Icom IC-F4001 Instruction Manual
Icom IC-F4001 Manual
 |
View all Icom IC-F4001 manuals
Add to My Manuals
Save this manual to your list of manuals |
Icom IC-F4001 manual content summary:
- Icom IC-F4001 | Instruction Manual - Page 1
Limited functions only INSTRUCTION MANUAL VHF TRANSCEIVERS iF3000 Series UHF TRANSCEIVERS iF4000 Series This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. The photo shows the VHF transceiver. - Icom IC-F4001 | Instruction Manual - Page 2
INSTRUCTION MANUAL- This in- struction manual contains important operating instructions for the IC-F3001/IC-F3003 VHF TRANSCEIVERS and the IC-F4001/IC-F4003 or electric shock. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the - Icom IC-F4001 | Instruction Manual - Page 3
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio Icom Inc., could void your authority to operate this transceiver under FCC regulations. Icom, Icom Inc. and Icom logo are registered trademarks of Icom - Icom IC-F4001 | Instruction Manual - Page 4
or in an explosive atmosphere. R WARNING! NEVER use or charge Icom battery packs with nonIcom transceivers or non-Icom chargers. Only Icom battery packs are tested and approved for use with Icom transceivers or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers - Icom IC-F4001 | Instruction Manual - Page 5
change and then the transceiver may not comply with the requirements of required regulations. The transceiver warranty does not cover any problems caused by unauthorized modification. CAUTION: DO NOT place or leave the transceiver in excessively dusty environments. This could damage the transceiver - Icom IC-F4001 | Instruction Manual - Page 6
OPERATION 12-22 ■ Turning power ON 12 ■ Channel selection 13 ■ Call procedure 14 ■ Receiving and transmitting 15 ■ Setting the microphone gain 18 ■ Setting the squelch level 19 ■ Output power level selection 20 ■ Priority A channel selection 20 ■ MDC 1200 system operation 20 ■ Emergency - Icom IC-F4001 | Instruction Manual - Page 7
1 2 4 BATTERY CHARGING 23-33 ■ Caution (for the BP-264 ni-mh battery 23 3 ■ Caution (for the BP-265 li-ion battery 25 4 ■ Battery chargers 28 5 BATTERY CASE 34 5 ■ Optional battery case (BP-263 34 6 6 OPTIONS 35-40 7 ■ VOX function 38 8 9 10 11 12 13 14 15 16 17 18 19 20 vi - Icom IC-F4001 | Instruction Manual - Page 8
1 ACCESSORIES ■ Supplied accessories The following accessories are supplied with the transceiver. Battery pack* Flexible antenna (This illustration is for the VHF type.) Battery charger* Power adapter* Belt clip* Jack cover (with screws) * Not supplied, or the shape is different, depending on - Icom IC-F4001 | Instruction Manual - Page 9
transceiver, if it is attached. (p. 3) 13 w Lift the tab up (q), and slide the belt clip in the direction of the arrow (w). 14 15 q w 16 17 18 Tab 19 20 2 - Icom IC-F4001 | Instruction Manual - Page 10
1 ACCESSORIES D Battery pack/case To attach the battery pack/case: q Fit the battery pack/case in the direction of the arrow (q), then close. w Hook the latch until it makes a 'click' sound (w). q Battery pack/case w Latch To remove the battery pack/case: Unhook the latch (e), and lift up the - Icom IC-F4001 | Instruction Manual - Page 11
MIC] jack. phillips screwdriver. 9 w Tighten the screws. r Detach the jack cover to con- nect the optional equipment. 10 11 12 13 w q w 14 e 15 e r 16 17 18 19 20 4 - Icom IC-F4001 | Instruction Manual - Page 12
q ROTARY SELECTOR w VOLUME CONTROL e LED INDICATOR u PTT SWITCH y UPPER KEY t LOWER KEY Speaker r SPEAKER- MICROPHONE JACK Microphone q ROTARY SELECTOR Rotate to select the pre-programmed memory channels. w VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF, and adjust the audio level. 5 - Icom IC-F4001 | Instruction Manual - Page 13
the matched 2/5-tone code is re- 6 ceived, depending on the pre-programming. 7 r SPEAKER-MICROPHONE JACK [SP MIC] Connect the optional speaker-microphone The desired function can be assigned by your dealer. (p. 8) 17 18 u PTT SWITCH [PTT] Push and hold to transmit; release to receive. 19 - Icom IC-F4001 | Instruction Manual - Page 14
detected during TX mode. w BATT 1 R* R* • TX low Battery 2: Very Low Battery was detected during TX mode. w BATT 2 R* R* R* R* • Channel Error: A non-programmed channel is selected. R O R O R O R O R O R O R O R O * Lights (or blinks) orange when the optional battery case is attached. 7 - Icom IC-F4001 | Instruction Manual - Page 15
function keys. 3 Consult your Icom dealer or system operator for details concerning your transceiver's programming. 4 SCAN A 5 ➥ respectively. 17 MEMORY CHANNELS 1, 2, 3, 4 18 Push to directly select memory channel 1, 2, 3 or 4, if programmed. 19 Consult your dealer for details. 20 - Icom IC-F4001 | Instruction Manual - Page 16
2 PANEL DESCRIPTION MONITOR, MONITOR (AUDIBLE) ➥ Push to turn the CTCSS (DTCS) or 2/5-tone squelch Mute ON or OFF. • Only during LMR operation, push to open any squelch func- tions, or deactivate any mute functions. • Only during PMR operation, push to activate one or two of the following - Icom IC-F4001 | Instruction Manual - Page 17
25 kHz using the optional cloning software (PMR operation only). Ask your dealer 6 for details. 7 ➥ Push and hold to switch the IF bandwidth to Narrow. 8 DTMF AUTODIAL Push to transmit a programmed DTMF code. 9 10 CALL, which call is assigned to each key. 14 15 16 17 18 19 20 10 - Icom IC-F4001 | Instruction Manual - Page 18
2 PANEL DESCRIPTION EMERGENCY Push and hold for specified time period to transmit an emergency call. • The emergency call transmits with beeps, and the LED indicator lights red. • The transceiver can transmit an emergency call without the beep sounding and the LED indicator lighting. Ask your - Icom IC-F4001 | Instruction Manual - Page 19
[PTT], the count down beeps sound. After that, a long beep sounds.) 17 • 1 beep sounds after the long beep when the Li-ion battery is selected. 18 • 2 beeps sound after the long beep when the battery case is selected. • 3 beeps sound after the long beep when the Ni-MH battery is selected - Icom IC-F4001 | Instruction Manual - Page 20
3 BASIC OPERATION ■ Channel selection Several types of channel selecting methods are available. They may differ, according to your system set up. To select a desired operating channel, do one of the following. • Rotate [ROTARY SELECTOR]. • Push one of memory channel keys, [MR-CH 1] to [MR-CH 4]. - Icom IC-F4001 | Instruction Manual - Page 21
you. 5 6 q Select a desired TX code channel or 2/5-tone code, according to your System Operator's instructions. 7 • This may not be necessary, depending on programming. 8 w Push [Call] (assigned to one of the dealer programmable keys.) (p. 10) 9 e After transmitting a 2/5-tone - Icom IC-F4001 | Instruction Manual - Page 22
3 BASIC OPERATION ■ Receiving and transmitting CAUTION: Transmitting without an antenna will damage the transceiver. See p. 1 for antenna attachment. Receiving: q Rotate [VOL] to turn power ON. w Rotate [ROTARY SELECTOR], or push one of the memory chan- nel keys, [MR-CH 1] to [MR-CH 4], to select a - Icom IC-F4001 | Instruction Manual - Page 23
'receive only' channel. 7 8 • Time-out timer After continuously transmitting longer than the pre-programmed time 9 period, the time-out timer activates, and stops further transmitting. 10 • Penalty timer 11 (end of transmission), depending on the 15 presetting. 16 17 18 19 20 16 - Icom IC-F4001 | Instruction Manual - Page 24
3 BASIC OPERATION D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is usable. ➥ Push [DTMF Autodial] to transmit the DTMF code. D Receiving a Stun, Kill and Revive command The dispatcher can send a 2/5-tone signal that will stun, - Icom IC-F4001 | Instruction Manual - Page 25
15 of beep that sounds. t Rotate [VOL] to turn the power OFF, then ON to exit the micro- 16 phone gain adjustment mode. 17 NOTE: 18 • This operation may not be available, depending on the presetting. Ask your dealer for details. 19 • When using the VOX function, we recommend setting the - Icom IC-F4001 | Instruction Manual - Page 26
3 BASIC OPERATION ■ Setting the squelch level The squelch circuit mutes the received audio signal, depending on the signal strength. q Rotate [VOL] to turn the trans- [ROTARY SELECTOR] ceiver power OFF. w S et [ROTARY SELECTOR] to [VOL] any channel other than Chan- nel 16. e While pushing - Icom IC-F4001 | Instruction Manual - Page 27
MDC 1200 system's Emergency feature can be accessed using the [Emergency] key. The transceiver will send an Emergency 18 MDC 1200 system command once, or repeatedly for a programmed 19 number of times until it receives the acknowledgement signal. 20 The emergency call can be transmitted without - Icom IC-F4001 | Instruction Manual - Page 28
channel. If you want to cancel the emergency call, push and hold [Emergency] again before transmitting the call. If your transceiver is programmed for Silent operation, you can transmit an Emergency call without the beep sounding and the LED indicator lighting. IMPORTANT: It is recommended to - Icom IC-F4001 | Instruction Manual - Page 29
and hold to turn the Lone Worker function ON. 9 w Push to turn the Lone Worker function OFF. 10 11 12 13 14 15 16 17 18 19 20 22 - Icom IC-F4001 | Instruction Manual - Page 30
(above +55˚C; +131˚F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after charging. Keep it safely in a cool dry place at the following temperature range: -20˚C to +45˚C (-4˚F to +113˚F) (up to a month) -20˚C to +35 - Icom IC-F4001 | Instruction Manual - Page 31
the battery pack until it becomes almost completely ex- 15 hausted, under normal conditions. We recommend battery charg- 16 ing after transmitting becomes impossible. 17 18 19 20 24 - Icom IC-F4001 | Instruction Manual - Page 32
the transceiver may not turn ON. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause - Icom IC-F4001 | Instruction Manual - Page 33
purpose that is not specified in this instruction manual. 4 R DANGER! If fluid from inside If any of these conditions occur, contact your Icom dealer or distributor. 8 R WARNING! Immediately radio after discharging. You may use the battery until the remaining capacity is about half, 18 then - Icom IC-F4001 | Instruction Manual - Page 34
is not waterproof. CAUTION: DO NOT charge the battery outside of the specified temperature range: BC-193 (+10˚C to +40˚C; +50˚F to +104˚F). Icom recommends charging the battery at +20˚C (+68˚F). The battery may heat up or rupture if charged out of the specified temperature range. Additionally - Icom IC-F4001 | Instruction Manual - Page 35
12 13 14 15 Screws* (Self tapping screw: 16 M3.5 × at least 30 mm) *Purchase separately. 17 Using screws is recom- mended to secure the 18 charger. Charge indicator 19 • Lights orange: While charging. 20 • Lights green: Charging is completed. 28 - Icom IC-F4001 | Instruction Manual - Page 36
4 BATTERY CHARGING D Using the BC-192 to regular charge the BP-264 The BC-192 provides regular charging of the Ni-MH battery pack (BP-264 only). Never use for any other battery pack. Charging time period for the BP-264 (with BC-147S) : Approximately 16 hours The following item is - Icom IC-F4001 | Instruction Manual - Page 37
Screws* (Self tapping screw: 15 M3.5 × at least 30 mm) *Purchase separately. 16 Using screws is recom- mended to secure the 17 charger. Charge indicator 18 • Lights orange: While charging. 19 • Lights green: Charging is completed. 20 30 - Icom IC-F4001 | Instruction Manual - Page 38
4 BATTERY CHARGING D U sing the BC-197 to rapid charge the BP-264 or BP-265 The BC-197 rapidly charges up to six battery packs. Charging time for the BP-264: Approximately 2 hours Charging time for the BP-265: Approximately 2.5 hours The following additional item is required: • A power adapter ( - Icom IC-F4001 | Instruction Manual - Page 39
adapter. The type of battery it holds is printed on 8 the top right corner of the adapter. 9 10 11 12 13 14 15 16 17 18 19 20 32 - Icom IC-F4001 | Instruction Manual - Page 40
4 BATTERY CHARGING IMPORTANT: Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger. Tabs Guide rail 33 - Icom IC-F4001 | Instruction Manual - Page 41
incinerate used battery cells since internal battery gas 17 may cause them to rupture. • Never expose a detached battery case to water. If the battery 18 case gets wet, be sure to wipe it dry before using it. 19 • Never use batteries whose insulated cover is damaged. NOTE: When the optional - Icom IC-F4001 | Instruction Manual - Page 42
6 OPTIONS D BATTERY PACK Battery pack Voltage Capacity Battery life*1 BP-263 Battery case for AA (LR6) × 6 alkaline -*2 BP-264 7.2 V 1400 mAh (min.) 1420 mAh (typ.) VHF 14.1 hrs. UHF 13.7 hrs. BP-265 7.4 V 1850 mAh (min.) 2000 mAh (typ.) VHF 20.2 hrs. UHF 19.6 hrs. *1 When the power - Icom IC-F4001 | Instruction Manual - Page 43
on 2 the version. There are two types of BC-197 chargers for the ICF3000/IC-F4000 series. 3 BC-197 Charger Type Chargeable Battery Charging time 4 With AD-120* MHz 17 FA-SC57VS : 160-174 MHz • FA-SC25U/FA-SC57U/FA-SC72U/ 18 FA-SC25V/FA-SC55V antennas FA-SC25U : 400-430 MHz FA-SC57U : 430- - Icom IC-F4001 | Instruction Manual - Page 44
BC-192 and BC-193 battery chargers. Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom transceiver is used with equipment that is not manufactured - Icom IC-F4001 | Instruction Manual - Page 45
-94, HS-95 or HS-97) and OPC-2004 as described below. 10 OPC-2004 11 [VOL] HS-94 12 13 14 w 15 16 e 17 q 18 19 20 38 - Icom IC-F4001 | Instruction Manual - Page 46
6 OPTIONS D Turning the VOX function ON or OFF The VOX function can be turned ON or OFF when turning the transceiver power ON. q Rotate [VOL] to turn the transceiver power OFF. w Set [ROTARY SELECTOR] to any channel other than Channel 16. e While pushing and holding [Upper], turn the transceiver - Icom IC-F4001 | Instruction Manual - Page 47
type 15 of beep that sounds. y R otate [VOL] to turn the power OFF, then ON to exit the VOX 16 gain adjustment mode. 17 NOTE: 18 • This operation may not be available, depending on the preset- 19 ting. Ask your dealer for details. • Set the microphone gain before setting the VOX - Icom IC-F4001 | Instruction Manual - Page 48
A6797-1EX-3a Printed in Japan © 2009-2018 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
 |
 |
INSTRUCTION MANUAL
This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition that
this device does not cause harmful interference.
UHF TRANSCEIVERS
iF4000
Series
VHF TRANSCEIVERS
iF3000
Series
Limited functions only
The photo shows
the VHF transceiver.