Hoveround Teknique HD6 User Manual
Hoveround Teknique HD6 Manual
 |
View all Hoveround Teknique HD6 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hoveround Teknique HD6 manual content summary:
- Hoveround Teknique HD6 | User Manual - Page 1
TEKNIQUE Power Wheelchairs TEKNIQUE FWD TEKNIQUE HD-6 ATTENTION: Please read the content of your owner's manual before operating your power wheelchair. TEKNIQUE RWD OWNER'S MANUAL & WARRANTY D82007778 REV N 7/10/12 TEKNIQUE XHD TEKNIQUE GT - Hoveround Teknique HD6 | User Manual - Page 2
2 D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 3
Notes usually contain information regarding troubleshooting the power wheelchair when an indicator or fault light appears. Using the Hoveround® product safely depends upon your diligence in following the warnings, cautions, and instructions in this owner's manual. Hoveround® is not responsible for - Hoveround Teknique HD6 | User Manual - Page 4
Dear Teknique Owner, Congratulations on your choice of the Hoveround® Teknique to fulfill your personal mobility needs. The Teknique has the same innovation of design that is the hallmark of our company. It is compact yet very stable; attractive yet rugged; simple yet functional; gentle yet powerful - Hoveround Teknique HD6 | User Manual - Page 5
8 Hoveround® Teknique / Diagram 12 Hoveround® Teknique / Warning Labels 13 Chapter 1 Operating Instructions 17 Entering Your Teknique 17 Driving Your Teknique 18 Joystick Controllers 20 Chapter 2 Batteries and Charging 22 Caring For Your Batteries and Charger 22 Battery Replacement 23 - Hoveround Teknique HD6 | User Manual - Page 6
FWD, XHD, HD-6 models only) . . . . . 38 Legrests 39 Chapter 7 Options and Accessories 40 Chapter 8 Routine Maintenance 43 Chapter 9 Disassembling and Reassembling Your Teknique 46 Controller Removal/Replacement 57 Appendix E Record of Service 62 Limited Warranty 66 6 Table of - Hoveround Teknique HD6 | User Manual - Page 7
phone call away. If we cannot answer your questions over the phone, or in the unlikely event your chair requires repair, we will dispatch a Field Service Technician to your home. Just call Hoveround® Technical Support and Repair, toll free at 1-800-96-HOVER (1-800-964-6837). D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 8
Use Your Teknique Before You Use Your Teknique The Hoveround® Teknique is a battery-operated motorized vehicle. The operation of the power wheelchair important safety warnings. Please read this entire manual thoroughly, and follow all warnings and instructions to avoid serious injury or death. Call - Hoveround Teknique HD6 | User Manual - Page 9
capacity of your Hoveround® Teknique HD-6 power wheelchair. To avoid serious injury or fatality from sudden unexpected movement of the chair or contact with moving parts and other objects: • Keep your hands, legs and feet away from moving wheels. • Do not use your power wheelchair with bare feet - Hoveround Teknique HD6 | User Manual - Page 10
. • Do not operate the power wheelchair in conditions such as rain, standing water, sleet, slush or snow. • Do not sit in your power wheelchair while riding in a motor vehicle, even if the chair is secured to the vehicle and you are using the chair's restraint. 10 General Warnings D82007778 - Hoveround Teknique HD6 | User Manual - Page 11
• Do not reach over the back of the chair or lean excessively forward or sideways. • Do not carry passengers or cargo. • Do not stand on footplate. Do not put weight on footplate, armrest or controller while getting into or out of the power wheelchair. D82007778 REV N 7/10/12 General Warnings 11 - Hoveround Teknique HD6 | User Manual - Page 12
Hoveround® Teknique - Diagram Adjustable Seatback Joystick Controller • Removable Seat • Flip-Up Foot Rest • Anti-Tip Wheels • • • Adjustable Armrests • Seat Belt • • • • Seat Height & Position Adjustment Batteries Dual Motor Drive Brake Release Levers 12 Hoveround® Teknique - Diagram - Hoveround Teknique HD6 | User Manual - Page 13
Hoveround® Teknique FWD Warning Labels For VSI For VR2 For FWD For VSI •• • • • • • For EMI warning label see page 16. D82007778 REV N 7/10/12 Hoveround® Teknique - Warning Labels 13 - Hoveround Teknique HD6 | User Manual - Page 14
Hoveround® Teknique XHD and HD-6 Warning Labels For VSI (XHD) For VR 2 (XHD & HD-6) For HD-6 For XHD For VSI •• • • • • • For EMI warning label see page 16. 14 Hoveround® Teknique - Warning Labels D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 15
Hoveround® Teknique RWD and GT Warning Labels For VSI For GT Pilot+ •• • • For VR2 D82007778 REV N 7/10/12 For EMI warning label see page 16. Hoveround® Teknique - Warning Labels 15 - Hoveround Teknique HD6 | User Manual - Page 16
EMI, Warning Label 16 Hoveround® Teknique - Warning Labels D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 17
to minimum while learning to drive the power wheelchair. Entering Your Teknique 1. Be sure the power is turned "OFF" before entering or exiting your Hoveround®. To locate the "ON/OFF" button on your joystick controller, see the section on joystick controller (page 20) to identify the type of - Hoveround Teknique HD6 | User Manual - Page 18
page 20 to identify the type of controller on your Teknique. 2. Allow plenty of space to test drive your power wheelchair. 3. With the joystick in the center position (neutral), turn chair power on. Check battery gauge for adequate battery capacity. 4. Set the Speed/Response Control to the lowest - Hoveround Teknique HD6 | User Manual - Page 19
be heard as the controller releases the motor brakes and your power wheelchair will move slowly forward. Observe that if the joystick is released, the lever will return to center (neutral) and the power wheelchair will stop. Note that when the chair stops, another "click" will be heard as the brakes - Hoveround Teknique HD6 | User Manual - Page 20
is indicated. Return the joystick to center. If the chair does not move, reset the control by turning the power off and then on. Joystick Controllers All the controls and indicators necessary to drive your Teknique are located on the joystick controller. Your Teknique may be equipped with one - Hoveround Teknique HD6 | User Manual - Page 21
decrease. Press mode or move the joystick forward to lock the setting. 9. Horn Button - Press to make the horn sound. Additional Features Locking feature - Locks the controller. Refer to Appendix C (page 55) for operating instructions. Sleep mode - Your chair will either power down or go off if left - Hoveround Teknique HD6 | User Manual - Page 22
any part of the battery. • Batteries are heavy. Use proper lifting and handling practices to prevent dropping, pinching or lifting-related injuries. • ALWAYS make sure the protective terminal covers are installed and all battery connections and screws are tight before using your power wheelchair - Hoveround Teknique HD6 | User Manual - Page 23
by Hoveround®. • ALWAYS use batteries of the same type and capacity for this power wheelchair. • NEVER connect life support systems or auxiliary devices to your wheel chair battery. The electrical system may fail and cause severe injury and/or death. • Do not leave the battery charger connected - Hoveround Teknique HD6 | User Manual - Page 24
for the batteries will vary based on the amount of use the chair has had. It may take up to 8 hours for a full recharge. We recommend an overnight charge after the day's use of your power wheelchair. • ALWAYS use the charger and connectors supplied with your Hoveround® power wheelchair. • DO NOT - Hoveround Teknique HD6 | User Manual - Page 25
a DC power source for any electrical or other equipment. • DO NOT attempt to charge a frozen battery. 1. Select a clean, dry, cool, well ventilated area to use the charger. 2. If your charger is equipped with an on/off button, ensure that the charger is in the OFF position, along with the joystick - Hoveround Teknique HD6 | User Manual - Page 26
. 5. Plug the other end of the AC power cord into a 120-volt grounded household power outlet. 6. Follow the specific instructions for your charger (see below). 7. When the batteries are charged, and/or you are ready to use the chair: A. If your charger is equipped with an on/off button, turn OFF - Hoveround Teknique HD6 | User Manual - Page 27
On occasion it may be necessary to push your Hoveround® power wheelchair. Each motor has a manual brake release lever. Refer to Figure 3A below to locate the manual brake release levers on your power wheelchair. • Always verify that the manual brake release levers are in the full "up" (engaged - Hoveround Teknique HD6 | User Manual - Page 28
and comfortable hand access to the joystick and speed/response control. • Inspect all areas of the skin in contact with power wheelchair daily. Discontinue use and contact physician at signs of skin irritation or discomfort. • Do not use power wheelchair until evaluated and instructed to do so by - Hoveround Teknique HD6 | User Manual - Page 29
Seat Belt Adjustment • Always fasten seat belt to maintain proper positioning in the seat and avoid injury. • Replace seat belt immediately at first signs of wear or improper latching. To fasten the seat belt, push the metal tab into the buckle until it - Hoveround Teknique HD6 | User Manual - Page 30
adjust the arm angle on the seat arms, lift the arm and locate the adjustment bolt near the pivot point. Refer to Figure 4D below. Use the supplied 1/4 inch hex wrench to make the adjustment. Turn the screw clockwise to lower the arm and counter clockwise to raise the arm. Figure - Hoveround Teknique HD6 | User Manual - Page 31
Arm Width Adjustment The standard seat has arm width adjustment (Figure 4F and 4G). To adjust the arm width: 1. Locate the two knobs and two set screws on the square tube at the rear of the seat. 2. Loosen the knobs and set screws. 3. Move the arms to a comfortable width. Make sure the tubes do not - Hoveround Teknique HD6 | User Manual - Page 32
tighten securely. Figure 4I The seat back will fold forward when pushed from the rear or pulled from the front. Always use caution when pushing the chair from the back. If the chair must be pushed from the back, push or pull on the arms or another solid surface. 32 Chapter 4 D82007778 REV - Hoveround Teknique HD6 | User Manual - Page 33
Adjusting The Seat Position Seats with side mounting brackets can be adjusted forward and rearward and up and down. To raise or lower the seat 1. Locate the hex head or socket head bolts on the side brackets below the seat. Loosen the rear bolts and remove the front bolts (See Figure 4J, below). 2. - Hoveround Teknique HD6 | User Manual - Page 34
below). Restrain the spring-loaded seatback either with your arm or by sitting in the chair and resting your back against the seatback. Move the spring loaded lever counter clockwise by pulling the lever arms. 34 Chapter 4 Lock Release Figure 4K - Manual Recline Lever D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 35
Seatback Adjustment for 22" and 24" Reclining Back Seat - The 22 and 24 inch seats have a heavy duty, dual hinge mechanism that allows you to adjust the seatback from the right or left side. The seatback release has two modes - one to recline or raise the seatback and one to release the seatback to - Hoveround Teknique HD6 | User Manual - Page 36
- Reclining Back Seats Arm Height Adjustment The arms can be raised from the standard position by repositioning the bolts that hold the arm in place. See Figure 4O below for bolt location. Locate the upper threaded hole by putting your finger on the fabric above the top bolt. Move up about 1 inch - Hoveround Teknique HD6 | User Manual - Page 37
start (See Figure 5A below). Do not remove Anti-Tip wheels. Figure 5A RWD and GT Anti-Tip Wheels (Rear Wheel Drive Shown) Figure 5A FWD, XHD and HD-6 Anti-Tip Wheels (Front Wheel Drive Shown) D82007778 REV N 7/10/12 Chapter 5 37 - Hoveround Teknique HD6 | User Manual - Page 38
rest on the plate(s) of the footrest/legrests. You can make several adjustments to maximize safety and comfort. In addition, a bracket mounted to the underside front of the seat accommodates swing-away legrests. Flip-Up Style Footrest (FWD the footplate height by using the upper or lower mounting holes - Hoveround Teknique HD6 | User Manual - Page 39
onto the appropriate hanger bracket and swing into the forward facing position. If your chair has elevating legrests, set the angle to the lowest position. 2. Fold down the foot plates. Your feet should comfortably rest on the plates without a tendency to lift your thighs from the seat cushion - Hoveround Teknique HD6 | User Manual - Page 40
pricing on accessories, contact HOVEROUND® CORPORATION at 800-96-HOVER (800-964-6837). Optional Tie-Down Brackets When transporting the Teknique in a motor vehicle, your wheelchair power wheelchair while riding in a motor vehicle even if the chair is secured to the vehicle and you are using the chair - Hoveround Teknique HD6 | User Manual - Page 41
When the indicator light is lit, move the joystick forward to raise the seat, back to lower. The Teknique will not drive while seat is raised and light is on. When seat is fully down, press either button to restore drive mode. Your power wheelchair contains a lock-out feature that prevents driving - Hoveround Teknique HD6 | User Manual - Page 42
Accessories Cane Holder Crutch Holder Beverage Holder Elevating Legrests Power Chair Lift Oxygen (Round) Oxygen (Square) Seat with Pan Seat with Pan and Cushion Step & Threshold Ramps 42 Chapter 7 D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 43
the safe operation of your power wheelchair. Service Please contact Hoveround® Technical Support at 1-800-96-HOVER (1-800-964-6837) for any service or maintenance needs. Stop using your power wheelchair immediately, and call for assistance if: • Your power wheelchair is not working correctly. • Your - Hoveround Teknique HD6 | User Manual - Page 44
signs of electrical damage. • Check that the seat swivel lock engages and holds (if so equipped). • Clean power wheelchair. (See page 45 for instructions.) A worn or improperly latching seat belt may not properly position you in the seat and can result in serious injury or death. Replace the seat - Hoveround Teknique HD6 | User Manual - Page 45
a mild detergent or window cleaner. Tires - Brush-off loose material with a dry bristle brush and wipe with a damp cloth or towel. Top Cover - Vacuum or brush off dirt, then wipe with a damp cloth or towel, using a mild detergent. Joystick - Ensure that the power switch is off before attempting - Hoveround Teknique HD6 | User Manual - Page 46
Chapter 9 Disassembling and Reassembling Your Teknique Controller Removal/Replacement Removal 1. Check that vehicle power is OFF. 2. Lift the arm and loosen the sockethead cap screw closest to the controller. Use the 1/4 inch hex wrench supplied with your chair (See Figure 9A below). 3. Slide the - Hoveround Teknique HD6 | User Manual - Page 47
tilt the seat back and remove from the rear slots. Replacement 1. Locate the rear mounting holes on the brackets attached rear of the frame bracket and allow the seat to rest in the forward position on the base frame. 4. Locate beyond the chair. Use care when driving to keep the cable from catching on objects - Hoveround Teknique HD6 | User Manual - Page 48
joystick to the junction box is a critical part of the vehicle. Ample cable is provided to allow for adjustments. There is a danger if this cable is not correctly routed. Do not allow the excess cable to extend beyond the width of the chair the chair. Use care when driving to keep the cable from catching on - Hoveround Teknique HD6 | User Manual - Page 49
to the owner's manual for all power wheelchairs. Electromagnetic Interference ( EMI ) From Radio Wave Sources. Power wheelchairs and motorized level, which would provide useful protection from the more common sources of radiated EMI. This Teknique power wheelchair model, as shipped, without - Hoveround Teknique HD6 | User Manual - Page 50
even when they are not being used for communication. 2. Medium range mobile transceivers, such as those used in police cars, fire trucks, electric shavers and hair dryers, as far as we know, are not likely to cause problems to your power wheelchair. Radio Wave sources may affect power wheelchair - Hoveround Teknique HD6 | User Manual - Page 51
such as citizens band (CB) radios and cellular phones, while the power wheelchair is turned ON. 2. Be aware of nearby transmitters, such as useful immunity level against interference from radio wave sources (as of May 1994, the higher the level, the greater the protection). 2. The Teknique wheelchair - Hoveround Teknique HD6 | User Manual - Page 52
Programmable Parameters The controller used on your power wheelchair is programmable for basic on the style of control system on your chair. Any subsequent change of the programmed values Speed Max Turning Speed Min Turning Acceleration Turning Deceleration TEK FWD VSI VR2 85 75 10 20 30 20 50 65 - Hoveround Teknique HD6 | User Manual - Page 53
system again and try to drive the chair. If the fault occurs again, switch off and do not try to use the wheelchair. Contact Hoveround Support 1-800-96-HOVER (1-800-964-6837) Controllers with system status indicator Tekniques with this controller system use a flashing "System Status Indicator" light - Hoveround Teknique HD6 | User Manual - Page 54
, right motor to battery. 6 bars: Verify battery charger is not plugged in (Pilot). Controller fault (VSI). 7 bars: Joystick fault. 8 bars: Controller fault. 9 bars: Problem with brake circuit. Check that manual brake release levers are in the drive position and power seat lift is lowered - Hoveround Teknique HD6 | User Manual - Page 55
feature. Please refer to the appropriate instructions for the controller on your Teknique. Key Lock Systems Figure 11E - Pilot Figure 11F - Pilot+ Figure 11G - Pilot & Pilot+ Key 1. Turn the controller on. 2. To lock the unit, insert and REMOVE the key at the charger port (See Figure 11E and 11F - Hoveround Teknique HD6 | User Manual - Page 56
the key (See Figure 11E and 11F, Page 55). The displays will illuminate indicating the controller is unlocked and the chair can be operated. Lock Sequence System ON/OFF Button Joystick Figure 11H - VSI or VR2 1. Turn the controller on. 2. To lock, depress and hold the on/off button. After one - Hoveround Teknique HD6 | User Manual - Page 57
Appendix D: Teknique FWD Specifications Performance Maximum Speed Range (per battery charge) Capacity Turning batteries** 179 lbs Base only** 90 lbs Base with batteries** 139 lbs Batteries** Two U1 batteries, 33 amp hour capacity each, Sealed AGM Tires and casters Tire type and tread Tire - Hoveround Teknique HD6 | User Manual - Page 58
Appendix D: Teknique RWD Specifications Performance Maximum Speed Range (per battery charge) Capacity Turning batteries 229 lbs Base only 100 lbs Base with batteries 178 lbs Batteries Two group 22 batteries, 50 amp hour capacity each, Sealed AGM Tires and casters Tire type and tread Tire - Hoveround Teknique HD6 | User Manual - Page 59
Appendix D: Teknique XHD Specifications Performance Maximum Speed Range (per battery charge) Capacity Turning batteries 273 lbs Base only 114 lbs Base with batteries 222 lbs Batteries Two group 24 batteries, 75 amp hour capacity each, Sealed AGM Tires and casters Tire type and tread Tire - Hoveround Teknique HD6 | User Manual - Page 60
Appendix D: Teknique HD-6 Specifications Performance Maximum Speed Range (per battery charge) Capacity Turning batteries 279 lbs Base only 120 lbs Base with batteries 228 lbs Batteries Two group 24 batteries, 75 amp hour capacity each, Sealed AGM Tires and casters Tire type and tread Tire - Hoveround Teknique HD6 | User Manual - Page 61
Appendix D: Teknique GT Specifications Performance Maximum Speed Range (per battery charge) Capacity Turning batteries 242 lbs Base only 102 lbs Base with batteries 181 lbs Batteries Two group 22 batteries, 50 amp hour capacity each, Sealed AGM Tires and casters Tire type and tread Tire - Hoveround Teknique HD6 | User Manual - Page 62
Appendix E: Record of Service Date Technician Service Performed 62 Chapter 11 D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 63
Record of Service Date Technician Service Performed D82007778 REV N 7/10/12 Chapter 11 63 - Hoveround Teknique HD6 | User Manual - Page 64
Record of Service Date Technician Service Performed 64 Chapter 11 D82007778 REV N 7/10/12 - Hoveround Teknique HD6 | User Manual - Page 65
Record of Service Date Technician Service Performed D82007778 REV N 7/10/12 Chapter 11 65 - Hoveround Teknique HD6 | User Manual - Page 66
of the Teknique FWD, RWD and GT to be free from defects in materials and workmanship for a period of five (5) years and the Teknique XHD and HD-6 for a period of one (1) year from the date of purchase. Hoveround® Corporation warrants all remaining components (excluding all upholstery, tires, tubes - Hoveround Teknique HD6 | User Manual - Page 67
D82007778 REV N 7/10/12 67 - Hoveround Teknique HD6 | User Manual - Page 68
Hoveround-TekManualRevN Format 8/7/12 3:37 PM Page 68 Phone: 1-800-96-HOVER (1-800-964-6837) Fax: 1-800-747-9252 6010 Cattleridge Drive | Sarasota, Florida 34232-6061 www.hoveround.com
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
 |
 |
D82007778 REV N
7/10/12
TEKNIQUE
Power Wheelchairs
OWNER’S MANUAL
& WARRANTY
TEKNIQUE FWD
TEKNIQUE XHD
TEKNIQUE GT
TEKNIQUE RWD
ATTENTION:
Please read the content
of your owner’s manual
before operating your
power wheelchair.
TEKNIQUE HD-6