Hitachi CPX380 User Manual

Hitachi CPX380 - XGA LCD Projector Manual

Get Hitachi CPX380 - XGA LCD Projector PDF manuals and user guides View all Hitachi CPX380 manuals
Add to My Manuals
Save this manual to your list of manuals

Hitachi CPX380 manual content summary:

  • Hitachi CPX380 | User Manual - Page 1
    ENGLISH Liquid Crystal Projector CP-X380W USER'S MANUAL Please read this user's manual thoroughly to ensure correct usage through understanding. TECHNICAL REGULATORY NOTICES
  • Hitachi CPX380 | User Manual - Page 2
    Options Menu 15 No Signal Menu 16 MAINTENANCE 17 Lamp 17 Air Filter 19 Other Maintenance 19 Page TROUBLESHOOTING 20 OSD Message 20 Indicators Message 21 Symptom 22 SPECIFICATIONS 23 WARRANTY AND AFTER-SERVICE ......24 TABLES Table 1. Installation Reference 6 Table 2. Cabling 7 Table
  • Hitachi CPX380 | User Manual - Page 3
    reshipment. Projector Liquid Crystal Projector CP-X380W USER'S MANUAL Please read this user's manual thoroughly to Video Cable (with green lead) Mouse cable (PS/2) STANDBY/ON BLANK LASER VIDEO RGB Batteries for Remote Control Transmitter AUTO MENU KEYSTONE MENU SELECT POSITION RESET
  • Hitachi CPX380 | User Manual - Page 4
    Adjuster REAR/RIGHT VIEW OF THE PROJECTOR INPUT Button LAMP Indicator TEMP Indicator POWER Indicator RESET Button MENU Button Ventilation Openings (exhaust) Terminal Panel (Refer below) S-VIDEO Terminal COMPONENT VIDEO Y Terminal CB/PB Terminal CR/PR Terminal VIDEO IN Terminal AUDIO IN R Terminal
  • Hitachi CPX380 | User Manual - Page 5
    VIDEO AUTO KEYSTONE MENU MENU SELECT RESET cause vision problems. AVOID remote control transmitter. • Do not wet the remote control transmitter or place it on any wet object. • Do not place the remote control transmitter close to the cooling fan of the projector. • Do not disassemble the remote
  • Hitachi CPX380 | User Manual - Page 6
    period, remove the batteries from the remote control transmitter. NOTE Replace the batteries when remote control transmitter operation becomes difficult. Make sure the handle is fixed before carrying the projector with the handle. If the projector should be dropped from the handle should be off,
  • Hitachi CPX380 | User Manual - Page 7
    CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. • When you fix • Do not install LCD projector in smoke effected environment. Smoke residue may buildup on critical parts (i.e.LCD panel, Lens Assy etc
  • Hitachi CPX380 | User Manual - Page 8
    have to be used with the core set to the projector side. Use the cables which are included with the projector or specified. NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the projector is compatible with the device. • Secure the screws on the
  • Hitachi CPX380 | User Manual - Page 9
    computer, set to valid the RGB external image output (setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of the notebook for more information. Plug & Play This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is
  • Hitachi CPX380 | User Manual - Page 10
    manual, and the separate "SAFETY INSTRUCTIONS" thoroughly before using the equipment. Always ensure that the equipment is used safely. NOTE • Except in emergencies, follow the above-mentioned procedure for turning power off. Incorrect procedure will reduce the life of the projector lamp and LCD
  • Hitachi CPX380 | User Manual - Page 11
    Video Input : Press the VIDEO button. RGB IN 1 / RGB IN 2 → VIDEO IN / S-VIDEO IN / COMPONENT VIDEO VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ VIDEO H PHASE. • The RESET button may operate as the remote control transmitter at a distance of approximately 5m from the sensor on the front of the projector
  • Hitachi CPX380 | User Manual - Page 12
    for the input signal is selected automatically. Valid only when AUTO is set for VIDEO on the menu. • This operation requires approximately 10 seconds. It may not SELECT Select Menu Type: Press the MENU SELECT button. Allows the user to select the normal menu or the single menu. Only the selected
  • Hitachi CPX380 | User Manual - Page 13
    if the horizontal size is excessive. In such cases, press the RESET button, and initialize the horizontal size. Soft ↔ Clear Light ↔ Dark RGB VIDEO S-VIDEO COMPONENT 480i 575i 480P 720P 1080i ✔✔✔✔ ✔✔✔✔ ✔- - - ✔- - - ✔ - ✔✔ ✔- - - -✔- - - ✔✔✔ TINT Red ↔ Green • Valid only
  • Hitachi CPX380 | User Manual - Page 14
    . It may not function correctly with some input signals. Pressing the AUTO button in this case may correct this problem except for the N-PAL input. • For the COMPONENT VIDEO input, this function is not effective and the signal type is distinguished automatically. Select HDTV mode: Select the 1035i
  • Hitachi CPX380 | User Manual - Page 15
    OPERATIONS (continued) Image Menu The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. SETUP INPUT BLANK MIRROR START UP GAMMA COLOR TEMP IMAGE OPT. Table 6. Image Menu
  • Hitachi CPX380 | User Manual - Page 16
    ENGLISH OPERATIONS (continued) Options Menu The following adjustments and settings are available when OPT. is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. SETUP INPUT VOLUME MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER IMAGE OPT.
  • Hitachi CPX380 | User Manual - Page 17
    and buttons. Table 8. No Signal Menu Item Description VOLUME BLANK Reduce ↔ Increase • When this function is used, audio input is automatically switched to video. The audio input can be switched by moving the DISK PAD left and right during the display of the volume adjustment bar. The volume
  • Hitachi CPX380 | User Manual - Page 18
    component in the projector and not necessarily the lamp. If unsure contact your local service center. • If it is probable that the lamp has exploded (explosive sound is heard), disconnect the power plug from the power outlet and ask your dealer to replace lamp. The lamp is covered by front
  • Hitachi CPX380 | User Manual - Page 19
    injury or accidents. • Do not use the projector with the lamp cover removed. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP indicator is red, or the CHANGE THE LAMP message is displayed, complete the following operation within
  • Hitachi CPX380 | User Manual - Page 20
    projector power supply OFF, and remove the power cord from the power outlet. 2. Clean the air filter with a vacuum cleaner. Replacing the Air Filter Replace before beginning maintenance work. Please read the separate "SAFETY INSTRUCTIONS" thoroughly to ensure that maintenance is performed correctly.
  • Hitachi CPX380 | User Manual - Page 21
    reset the lamp timer after replacing the lamp. NO INPUT IS DETECTED ON *** No input signal found. Check signal input connections and signal sources. SYNC IS OUT OF RANGE ON *** The horizontal or vertical frequency of the input signal is not within the specified range. Check the specifications
  • Hitachi CPX380 | User Manual - Page 22
    TROUBLESHOOTING (continued) Indicators Message The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the appropriate measures. Table 10. Indicators Message POWER LAMP Replace the lamp if the same problem occurs. Blinks /Lights red Blinks red Lamp or lamp
  • Hitachi CPX380 | User Manual - Page 23
    . adjusted. Brightness and contrast are not correctly adjusted. Adjust the video. 12 Images are dark. The lamp is nearing the end of its service life. Replace with a new lamp. 17 WHISPER mode is set. Clear WHISPER mode. 15 Video is blurred. Focus or H PHASE is out of adjustment. Adjust
  • Hitachi CPX380 | User Manual - Page 24
    Table 12. Specifications Item Specification Product name Liquid crystal projector Liquid crystal panel Panel size Drive system Pixels 2.3 cm (0.9 type) TFT active matrix 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=1.7 ~ 2.1 f=36.8 ~ 47.8 mm Lamp 200 W UHB
  • Hitachi CPX380 | User Manual - Page 25
    WARRANTY AND AFTER-SERVICE If a problem occurs with the equipment, first refer to the P.20 "TROUBLESHOOTING" section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied. ENGLISH-24
  • Hitachi CPX380 | User Manual - Page 26
    1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT) Pin No Signal Pin No Signal Pin No Signal 1 Video input Red 2 Video input Green 3 Video input Blue 4 - 5 Ground 6 Ground Red 7 Ground Green 8 Ground Blue 9 - 10 Ground 11 - RGB IN 1: SDA(DDC) 12 RGB IN 2: - RGB
  • Hitachi CPX380 | User Manual - Page 27
    have multiple display screen modes. Use of some of these modes will not be possible with this projector. • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. • Depending on the input signal, full-size display may not be possible in some
  • Hitachi CPX380 | User Manual - Page 28
    TECHNICAL (continued) Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu. Back porch b Front porch d Display interval c DATA Back porch b
  • Hitachi CPX380 | User Manual - Page 29
    and "MOUSE/RIGHT button" of page 4. 2. USB Mouse (1) Connect the projector and computer with a suitable commercially available USB cable. Consult your dealer to /RIGHT button" of page 4. NOTE • Before connecting, read the instruction manuals of the devices to be connected. • In the case of notebook
  • Hitachi CPX380 | User Manual - Page 30
    ADB Mouse CONTROL Terminal D-sub 15-pin shrink jack Serial Mouse CONTROL Terminal D-sub 15-pin shrink jack Projector 1 2 DATA 3 4 5 6 RTS 7 8 +5V 9 GND 10 11 12 13 14 15 Projector 1 2 3 4 5 SEL0 6 RTS 7 8 9 GND 10 11 12 13 TD 14 15 USB Mouse Computer 1 ADB 2 (POWER ON) 3 +5V 4 GND
  • Hitachi CPX380 | User Manual - Page 31
    the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector power supply. Control jack D-sub 15-pin shrink jack Projector 1 2 3 4 5 SELO 6 RTS 7 8 9 GND 10 11 12 RD 13 TD 14 15 Computer 1 CD 2 RD 3 TD 4 DTR 5 GND 6 DSR 7 RTS 8 DTS
  • Hitachi CPX380 | User Manual - Page 32
    projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code '06H' to the computer. Using the projector default settings (Reset . • The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore
  • Hitachi CPX380 | User Manual - Page 33
    TECHNICAL (continued) Names Blank Color Mirror Freeze Menu Color Startup Language Operation type Red Orange Green Set Blue Purple White Black Get Normal H Inverse Set V lnverse H&V Inverse Get Normal Set Freeze Get Red Orange Green Set Blue Purple Transparent Gray Get Turn
  • Hitachi CPX380 | User Manual - Page 34
    00 Brightness Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00 Contrast Reset Execute BE Fan-error) (Lamp-error) Power OFF Set ON Get RGB1 04 00 05 00 06 00 (Temp-error) (Air flow-error) (Lamp-Time-over) D0 01 00 00 20 04 00 Input Source Set Video SVideo BE EF BE EF 03 06 00 6E
  • Hitachi CPX380 | User Manual - Page 35
    TECHNICAL (continued) Names Operation type Mute Brightness Contrast Color Balance R Color Balance B Keystone_V Aspect Display Position at 16 : 9 or Small V.Position H.Position H.Size H.Phase Normal Set Mute Get Get Increment Decrement Get Increment Decrement Get Increment Decrement
  • Hitachi CPX380 | User Manual - Page 36
    TECHNICAL (continued) Names Operation type Sharpness Color Tint Video Format HDTV Get Increment Decrement Get Increment Decrement Get Increment Decrement Auto NTSC PAL Set SECAM NTSC 4.43 M-PAL N-PAL Get 1080i Set 1035i Get
  • Hitachi CPX380 | User Manual - Page 37
    TECHNICAL (continued) Names Operation type Set Sync on G Set WHISPER Set GAMMA Set COLOR TEMP off on Get NORMAL WHISPER Get NORMAL CINEMA DYNAMIC Get NORMAL LOW Get Command data chart Header Command data CRC Action Type Setting code BE EF 03 06 00 CB D0 01 00 08 30 01 00 BE EF 03 06 00 5B
  • Hitachi CPX380 | User Manual - Page 38
    radio/TV technician for help. INSTRUCTIONS TO USERS: This equipment complies with the projector side. Use the cables which are included with the projector or specified. Core CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user
  • Hitachi CPX380 | User Manual - Page 39
  • Hitachi CPX380 | User Manual - Page 40
    CA 94005-1835 Tel: +1-800-225-1741 Fax: +1-650-244-7776 www.hitachi.com/lcd. Hitachi Canada, Ltd. 6740 Campobello Road, Mississauga, Ontario L5N2L8, Canada Tel: +1-905-821-4545 Fax: +1-905-821-1101 Hitachi Home Electronics (Europe), Ltd. Dukes Meadow, Millboard Road, Bourne End , Buckinghamshire SL8
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
ENGLISH
Liquid Crystal Projector
CP-X380W
USER'S MANUAL
Please read this user's manual thoroughly to ensure correct usage through understanding.