Hikvision DS-2CD2532F-IS User Manual

Hikvision DS-2CD2532F-IS Manual

Get Hikvision DS-2CD2532F-IS PDF manuals and user guides View all Hikvision DS-2CD2532F-IS manuals
Add to My Manuals
Save this manual to your list of manuals

Hikvision DS-2CD2532F-IS manual content summary:

  • Hikvision DS-2CD2532F-IS | User Manual - Page 1
    User Manual of Network Camera Network Camera User Manual UD.6L0201D1919A01 1
  • Hikvision DS-2CD2532F-IS | User Manual - Page 2
    written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to Network Camera (V5.3.0). The Manual includes instructions for using and
  • Hikvision DS-2CD2532F-IS | User Manual - Page 3
    RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15
  • Hikvision DS-2CD2532F-IS | User Manual - Page 4
    of Network Camera with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
  • Hikvision DS-2CD2532F-IS | User Manual - Page 5
    Manual of Network Camera This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. Safety Instruction These instructions that the ceiling can support more than 50(N) service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems
  • Hikvision DS-2CD2532F-IS | User Manual - Page 6
    User Manual of Network Camera Cautions:  Make sure the power supply voltage is result in hazard of explosion. Please use the manufacturer recommended battery type. Notes: For the camera supports IR, you are required to pay attention to the following precautions to prevent IR reflection:  Dust
  • Hikvision DS-2CD2532F-IS | User Manual - Page 7
    Network Connection 33 Chapter 5 Live View 35 5.1 Live View Page ...35 5.2 Starting Live View 36 5.3 Recording and Capturing Pictures Manually 37 5.4 Operating PTZ Control 37 5.4.1 PTZ Control Panel ...37 5.4.2 Setting / Calling a Preset 38 5.4.3 Setting / Calling a Patrol 40 Chapter 6 Network
  • Hikvision DS-2CD2532F-IS | User Manual - Page 8
    User Manual of Network Camera 6.3.9 6.3.10 6.3.11 6.3.12 6.3.13 6.3.14 Configuring Wireless Dial Settings 55 Email Sending Intrusion Detection 101 6.6.13 Configuring Region Entrance Detection 103 6.6.14 Configuring Region Exiting Detection 104 6.6.15 Configuring Unattended Baggage Detection
  • Hikvision DS-2CD2532F-IS | User Manual - Page 9
    User Manual of Network Camera 7.2 Configuring Recording Schedule 128 7.3 Configuring Snapshot Settings 132 Filter 152 12.5 Security Service 153 12.6 Viewing Device Information 154 12.7 Maintenance ...155 12.7.1 Rebooting the Camera 155 12.7.2 Restoring Default Settings 155 12.7.3 Exporting
  • Hikvision DS-2CD2532F-IS | User Manual - Page 10
    User Manual of Network Camera Chapter 1 System Requirement Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium
  • Hikvision DS-2CD2532F-IS | User Manual - Page 11
    User Manual of Network Camera Chapter 2 Network Connection Note:  You shall acknowledge we recommend you to have the network camera assessed and maintained termly. You can contact us if you need such service. Before you start:  If you want to set the network camera via a LAN (Local Area Network),
  • Hikvision DS-2CD2532F-IS | User Manual - Page 12
    password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. interface. Notes:  The default IP address of the camera is 192.168.1.64.  For the camera enables the DHCP by default, you need to activate the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 13
    Manual of Network Camera Figure 2-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED- We highly recommend you create a strong password device, activating the camera, and resetting the password. Get the SADP software from the 13
  • Hikvision DS-2CD2532F-IS | User Manual - Page 14
    , lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click OK to save the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 15
    User Manual of Network Camera Figure 2-5 Modify the IP Address 6. Input the password and click the Save button to activate your IP address modification.  Activation via Client Software The client software is software and the control panel of the software pops up, as shown in the figure below. 15
  • Hikvision DS-2CD2532F-IS | User Manual - Page 16
    User Manual of Network Camera Figure 2-6 Control Panel 2. Click the Device Management icon to enter the Device Management interface, as shown in the figure below. Figure 2-7 Device Management Interface 16
  • Hikvision DS-2CD2532F-IS | User Manual - Page 17
    User Manual of Network Camera 3. Check the device status from the device list, and select an inactive device. 4. Click the Activate button to pop up the Activation interface. 5. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED- We
  • Hikvision DS-2CD2532F-IS | User Manual - Page 18
    by either modifying the IP address manually or checking the checkbox of Enable DHCP. 9. Input the password to activate your IP address IP Connection Before you start: Please apply a static IP from an ISP (Internet Service Provider). With the static IP address, you can connect the network camera via
  • Hikvision DS-2CD2532F-IS | User Manual - Page 19
    User Manual of Network Camera 2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 for detailed IP address configuration of the network camera. 3.
  • Hikvision DS-2CD2532F-IS | User Manual - Page 20
    Manual of Network Camera 1. Connect the network camera to the router. 2. In the camera, assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 for detailed IP address configuration of the network camera. 3. In the router, set the PPPoE user name, password camera supports the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 21
    User Manual of Network Camera Figure 2-13 Normal Domain Name Resolution Steps: 1. Apply a domain name from a domain name provider. 2. Configure the DDNS settings in the DDNS Settings interface of the network camera.
  • Hikvision DS-2CD2532F-IS | User Manual - Page 22
    User Manual of Network Camera first time using, refer to the section 2.1.2 for details. Note:  The default IP address is 192.168.1.64.  If the camera is not activated, -right of login interface. 5. Input the user name and password and click . The admin user should configure the device accounts
  • Hikvision DS-2CD2532F-IS | User Manual - Page 23
    User Manual of Network Camera 6. Install the plug-in before viewing the live video and operating the camera. Please follow the installation prompts to install the plug-
  • Hikvision DS-2CD2532F-IS | User Manual - Page 24
    User Manual of Network Camera web browser and log in again after installing the plug-in. 3.2 Accessing by Client Software The product CD contains the iVMS-4200
  • Hikvision DS-2CD2532F-IS | User Manual - Page 25
    User Manual of Network Camera Figure 3-6 iVMS-4200 Main View Note: For detailed information about the software, please refer to the user manual of the iVMS-4200. 25
  • Hikvision DS-2CD2532F-IS | User Manual - Page 26
    User Manual of Network Camera Chapter 4 Wi-Fi Settings Purpose: By connecting to the wireless network, you don't need to use cable of any kind for network
  • Hikvision DS-2CD2532F-IS | User Manual - Page 27
    Network mode as Manage, and the Security mode of the network is automatically shown when you select the wireless network, please don't change it manually. Note: These parameters are exactly identical with those of the router. 5. Enter the key to connect the wireless network. The key should be that
  • Hikvision DS-2CD2532F-IS | User Manual - Page 28
    User Manual of Network Camera Figure 4-5 Ad-hoc Connection Point 6. Choose the SSID and connect. Security Mode Description: Figure 4-6 Security Mode You can choose the Security Mode
  • Hikvision DS-2CD2532F-IS | User Manual - Page 29
    on the access point being used. The following options are available: HEX - Allows you to manually enter the hex key. ASCII - In this method the string must be exactly 5 characters for 64-bit WEP and 13 characters for 128-bit WEP. WPA-personal and WPA2-personal Mode: Enter the required Pre-shared
  • Hikvision DS-2CD2532F-IS | User Manual - Page 30
    User Manual of Network Camera Figure 4-9 EAP-TLS  Identity - Enter the user ID to present to the network.  Private key password - Enter the password for your user ID.  EAPOL version - Select the version used (1 or 2) in your access point.  CA Certificates - Upload a CA certificate to present to
  • Hikvision DS-2CD2532F-IS | User Manual - Page 31
    Manual of Network Camera numbers and special characters) in order to increase the security of your product.  Proper configuration of all passwords to the Push-Button-Configuration, in which the user simply has to push a button, either an actual or virtual one (as the button on the configuration
  • Hikvision DS-2CD2532F-IS | User Manual - Page 32
    User Manual of Network Camera 2. Choose the connection mode as PBC. Note: Support of this mode is mandatory for both the Access Points and the connecting devices. 3. Check on the Wi-Fi router to see if there is a WPS button. If yes push the button and you can see the indicator near the button start
  • Hikvision DS-2CD2532F-IS | User Manual - Page 33
    User Manual of Network Camera Figure 4-11 Wi-Fi Settings - WPS PIN Mode 2. in the example, enter 48167581 to the router. 4.3 IP Property Settings for Wireless Network Connection The default IP address of wireless network interface controller is 192.168.1.64. When you connect the wireless network you
  • Hikvision DS-2CD2532F-IS | User Manual - Page 34
    User Manual of Network Camera 1. Enter the TCP/IP configuration interface. Configuration> Advanced IP Settings 2. Select the NIC as wlan. 3. Customize the IPv4 address, the IPv4 Subnet Mask and the Default Gateway. The setting procedure is the same with that of LAN. If you want to be assigned the IP
  • Hikvision DS-2CD2532F-IS | User Manual - Page 35
    User Manual of Network Camera Chapter 5 Live View 5.1 Live View Page Purpose: The It lists the camera model you are connecting to. Online Help: Click to get the online help, which will guide you through the basic operations for each function. Menu Bar: Click each tab to enter Live View, Playback,
  • Hikvision DS-2CD2532F-IS | User Manual - Page 36
    User Manual of Network Camera Display Control: Click each tab to adjust , tilting and zooming actions of the camera and the light and wiper control. (only available for cameras supporting PTZ function) Preset/Patrol Settings: Set/call/delete the presets or patrols for PTZ cameras. 5.2 Starting
  • Hikvision DS-2CD2532F-IS | User Manual - Page 37
    third stream and 3D positioning require the support of camera. 5.3 Recording and Capturing Pictures Manually In the live view interface, click on control buttons to realize pan/tilt/zoom control of the camera. Note: To realize PTZ control, the camera connected to the network must support the PTZ
  • Hikvision DS-2CD2532F-IS | User Manual - Page 38
    User Manual of Network Camera Figure 5-3 PTZ Control Panel Click the zoom/iris/focus buttons to realize lens control. Notes:  There are 8 direction arrows in the live view window when you click and drag the mouse in the relative positions.  For the cameras which support lens movements only,
  • Hikvision DS-2CD2532F-IS | User Manual - Page 39
    User Manual of Network Camera Figure 5-4 Setting a Preset 2. Use the PTZ control buttons to move the lens to the desired  Calling a Preset: This feature enables the camera to point to a specified preset scene manually or when an event takes place. For the defined preset, you can call it at any
  • Hikvision DS-2CD2532F-IS | User Manual - Page 40
    User Manual of Network Camera 5.4.3 Setting / Calling a Patrol Note: No less than 2 presets have to be configured before you set a patrol. Steps: 1. Click to enter the patrol
  • Hikvision DS-2CD2532F-IS | User Manual - Page 41
    User Manual of Network Camera Chapter 6 Network Camera Configuration 6.1 Configuring Local Parameters Note: The local configuration refers to the parameters of the live view, record files and
  • Hikvision DS-2CD2532F-IS | User Manual - Page 42
    or 1G. After the selection, the maximum record file size is the value you selected.  Save record files to: Set the saving path for the manually recorded video files.  Save downloaded files to: Set the saving path for the downloaded video files in playback mode.  Picture and Clip Settings: Set the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 43
    User Manual of Network Camera 3. Click Save to save the settings. 6.2 Configuring Time Settings Purpose: You can follow the instructions in this section to configure the time synchronization and DST settings. Steps: 1. Enter the Time Settings interface: Configuration > Basic Configuration > System >
  • Hikvision DS-2CD2532F-IS | User Manual - Page 44
    : You can also check the Sync with computer time checkbox to synchronize the time of the camera with that of your computer. Figure 6-4 Time Sync Manually  Click the DST tab page to enable the DST function and Set the date of the DST period. Figure 6-5 DST Settings 2. Click Save to save
  • Hikvision DS-2CD2532F-IS | User Manual - Page 45
    Manual of Network Camera 6.3 Configuring Network Settings 6.3.1 Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the camera over network. The camera supports or IPv6 Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings 45
  • Hikvision DS-2CD2532F-IS | User Manual - Page 46
    User Manual of Network Camera and Multicast Address. 3. (Optional) Check the checkbox of Enable Multicast 2. Set the HTTP port, RTSP port, HTTPS port and server port of the camera. HTTP Port: The default port number is 80, and it can be changed to any port No. which is not occupied. RTSP Port: The
  • Hikvision DS-2CD2532F-IS | User Manual - Page 47
    Manual of Network Camera ranges from 1024 to 65535. HTTPS Port: The default port number is 443, and it can be changed to any port No. which is not occupied. Server Port: The default of your product.  Proper configuration of all passwords and other security settings is the responsibility of the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 48
    Manual of Network Camera Note: A reboot is required for the settings to take effect. 6.3.4 Configuring DDNS Settings Purpose: If your camera is set to use PPPoE as its default security of your product.  Proper configuration of all passwords and other security settings is the responsibility of the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 49
    User Manual of Network Camera and DynDNS.  DynDNS: Steps: (1)Enter Server Address of DynDNS (e.g. members.dyndns.org). (2)In the Domain text field, enter the domain name obtained from the DynDNS website. (3)Enter the Port of DynDNS server. (4)Enter the User Name and Password registered on the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 50
    User Manual of (4) Enter the Port number, if needed. (5) Enter the User Name and Password. (6) Click Save and then you can view the camera with the domain name.  HiDDNS Steps: (1)Choose the DDNS Type as HiDDNS. Figure 6-13 HiDDNS Settings (2) Enter the Server Address www.hik-online.com. (3)
  • Hikvision DS-2CD2532F-IS | User Manual - Page 51
    User Manual of Network Camera (4) Click Save to save the new settings. Note: different version according to the security level you required. SNMP v1 provides no security and SNMP v2 requires password for access. And SNMP v3 provides encryption and if you use the third version, HTTPS protocol must be
  • Hikvision DS-2CD2532F-IS | User Manual - Page 52
    User Manual of Network Camera Figure 6-14 SNMP Settings 2. Check the corresponding version checkbox ( , , ) to enable the feature. 3. Configure the SNMP settings. Note: The settings of the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 53
    Manual of Network Camera The IEEE 802.1X standard is supported be configured. Please apply and register a user name and password for 802.1X in the server.  For your privacy Configuration > Advanced Configuration > Network > 802.1X Figure 6-15 802.1X Settings 2. Check the Enable IEEE 802.1X checkbox
  • Hikvision DS-2CD2532F-IS | User Manual - Page 54
    User Manual of Network Camera 5. Click Save to finish the settings. Note: A reboot is required for the settings to take effect. 6.3.7 Configuring QoS Settings Purpose: QoS (Quality of Service) can help solve the network delay and network congestion by configuring the priority of data sending. Steps:
  • Hikvision DS-2CD2532F-IS | User Manual - Page 55
    network. Note: The wireless dial function requires the support of the camera. 1. Click the Wireless Dial tab manual dialing parameters. 2) Set the access number, user name, password, APN, MTU and verification protocol. You can also leave these parameters blank, and the device will adopt the default
  • Hikvision DS-2CD2532F-IS | User Manual - Page 56
    the security of your product.  Proper configuration of all passwords and other security settings is the responsibility of the installer and the offline time if Manual is selected as the dial mode. 5) Input the UIM Number (Mobile Phone Number). 6) Click the Edit button to set the arming schedule
  • Hikvision DS-2CD2532F-IS | User Manual - Page 57
    6-18 Dial Parameters 4. View the dial status. 1) Click the Refresh button to view the dial status including real-time mode, UIM status, signal strength, etc. 2) If Manual is selected as the dial mode, you can also manually connect / disconnect the wireless network. Figure 6-19 Dial Status 5. Set
  • Hikvision DS-2CD2532F-IS | User Manual - Page 58
    User Manual of Network Camera Figure 6-21 SMS Alarm Settings 3) Input the mobile phone number for the white list, check the checkbox of Reboot via SMS, select
  • Hikvision DS-2CD2532F-IS | User Manual - Page 59
    User Manual of Network Camera set the IPv4 Address, IPv4 Subnet Mask, IPv4 Default Gateway and the Preferred DNS Server. Note: Please Server IP address or host name (e.g., smtp.263xmail.com). SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25 (not secured). And the SSL SMTP port is 465.
  • Hikvision DS-2CD2532F-IS | User Manual - Page 60
    User Manual of Network Camera order to increase the security of your product.  Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end- port mapping mode. To port mapping with the default port numbers: Choose Port Mapping Mode as Auto. 60
  • Hikvision DS-2CD2532F-IS | User Manual - Page 61
    Camera To port mapping with the customized port numbers: Choose Port Mapping Mode as Manual. And for manual port mapping, you can customize the value of the port number by yourself. Figure FTP Figure 6-24 FTP Settings 2. Configure the FTP settings; and the user name and password are required for 61
  • Hikvision DS-2CD2532F-IS | User Manual - Page 62
    Manual of Network Camera login the FTP server.  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices. The password access function must be supported by the FTP server. 7.3. 6.3.13 Platform
  • Hikvision DS-2CD2532F-IS | User Manual - Page 63
    User Manual of Network Camera for the support of the camera. Check the checkbox of Enable to enable the EZVIZ Cloud P2P, and you are able to manage the device via EZVIZ Cloud
  • Hikvision DS-2CD2532F-IS | User Manual - Page 64
    User Manual of Network Camera Figure 6-26 HTTPS Settings  Create the self-signed certificate 1) Click Create button to enter the creation interface. Figure 6-27 Create Self-signed Certificate 2) Enter the country, host name/IP, validity and other information. 3) Click OK to save
  • Hikvision DS-2CD2532F-IS | User Manual - Page 65
    User Manual of Network Camera  Create the authorized certificate 1) Click Create button to create the certificate request. 2) Download the install the certificate. Figure 6-28 Installed Certificate 5. Click the Save button to save the settings. 6.4 Configuring Video and Audio Settings 6.4.1
  • Hikvision DS-2CD2532F-IS | User Manual - Page 66
    User Manual of Network Camera Figure 6-29 Video Settings 2. Select the Stream Type of the camera to main stream (normal), sub-stream or third stream. The main
  • Hikvision DS-2CD2532F-IS | User Manual - Page 67
    User Manual of Network Camera which the video stream is updated and it is : The video encoding type varies according to different camera platforms. For some certain cameras, H.265 is supported while MPEG4 is not. Profile: Basic profile, Main Profile and High Profile for coding are selectable.
  • Hikvision DS-2CD2532F-IS | User Manual - Page 68
    User Manual of Network Camera 6.4.2 Configuring Audio Settings Steps: 1. Enter the Audio Settings interface Configuration > Basic Configuration > Video / Audio > Audio Or Configuration > Advanced Configuration > Video / Audio > Audio
  • Hikvision DS-2CD2532F-IS | User Manual - Page 69
    User Manual of Network Camera whereas the background information is less focused. Note: ROI function varies according to different camera models. Figure 6-31 Region of Interest Settings
  • Hikvision DS-2CD2532F-IS | User Manual - Page 70
    User Manual of Network Camera 5. Click the Draw Area button, and then click-and-drag the mouse to region of interest. Note: To enable face tracking function, the face detection function should be supported and enabled. 3. Check the checkbox of Enable License Plate Tracking, and then the captured
  • Hikvision DS-2CD2532F-IS | User Manual - Page 71
    User Manual of Network Camera Figure 6-32 Display Info. on Stream 6.4.5 Configuring Target Cropping Purpose: You can specify a target area on the live video, and then it
  • Hikvision DS-2CD2532F-IS | User Manual - Page 72
    User Manual of Network Camera Figure 6-33 Target Cropping 6.5 Configuring Image Parameters 6.5.1 Configuring Display Settings Purpose: You can set the image quality of the camera, including brightness,
  • Hikvision DS-2CD2532F-IS | User Manual - Page 73
    from 1~100, and the default value is 50.  Exposure Settings If the camera is equipped with the fixed lens, only Manual is selectable, and the iris mode is not configurable. If Auto is selected, you can set the auto iris level from 0~ 100. For the camera supports
  • Hikvision DS-2CD2532F-IS | User Manual - Page 74
    of Network Camera 1/100,000s. Adjust it according to the actual luminance condition.  Focus Settings For the camera supports electronic lens, you can set the focus mode as Auto, Manual or Semi-auto. If auto is selected, the focus is adjusted automatically according to the actual monitoring scenario
  • Hikvision DS-2CD2532F-IS | User Manual - Page 75
    the IR LED, thus providing a clear image that is not overexposed or too dark. Select ON to enable the smart IR, and then Auto and Manual are selectable for IR mode. Select AUTO, and the power of IR LED changes automatically according to the actual luminance. E.g.: if the current scene is
  • Hikvision DS-2CD2532F-IS | User Manual - Page 76
    User Manual of Network Camera Figure 6-36 White Balance  Image Enhancement Digital Noise Reduction: DNR reduces the noise in the video stream. OFF, Normal Mode and Expert Mode are selectable. Set the DNR level from 0~100, and the default value is 50 in Normal Mode. Set the DNR level from both space
  • Hikvision DS-2CD2532F-IS | User Manual - Page 77
    User Manual of Network Camera Some of the camera supports CVBS, SDI, or HDMI output. Please refer to the actual camera model for details. Day/Night Scheduled-Switch Day/Night scheduled-switch configuration interface enables
  • Hikvision DS-2CD2532F-IS | User Manual - Page 78
    User Manual of Network Camera You can customize the camera name and time on the screen. Steps: 1. Enter the OSD Settings interface: Configuration > Advanced Configuration > Image > OSD
  • Hikvision DS-2CD2532F-IS | User Manual - Page 79
    User Manual of Network Camera live view window to adjust the OSD position. Figure 6-40 Adjust OSD Location 7. Click Save to activate the above settings. 6.5.3 Configuring Text
  • Hikvision DS-2CD2532F-IS | User Manual - Page 80
    User Manual of Network Camera Figure 6-41 Text Overlay 2. Check the checkbox in front of textbox to enable the on-screen display. 3. Input the characters in the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 81
    User Manual of Network Camera Note: You are allowed to draw up to 4 areas on the same image. 5. Click Stop Drawing to finish drawing or click Clear
  • Hikvision DS-2CD2532F-IS | User Manual - Page 82
    User Manual of Network Camera 6.6 Configuring and Handling Alarms This section explains how to , intrusion detection, defocus detection, scene change detection, etc. A help document will guide you to go through the configuration steps. 6.6.1 Configuring Motion Detection Purpose: Motion detection
  • Hikvision DS-2CD2532F-IS | User Manual - Page 83
    User Manual of Network Camera (1)Enter the motion detection settings interface Configuration > Advanced Configuration> Basic Event > Motion Detection (2)Check the checkbox of Enable Motion Detection. (3)Check the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 84
    User Manual of Network Camera Figure 6-45 Arming Time (1)Click Edit to edit the arming schedule. The Figure 6-34 shows the editing interface of the arming schedule. (2)
  • Hikvision DS-2CD2532F-IS | User Manual - Page 85
    User Manual of Network Camera 3. Set the Alarm Actions for Motion Detection. Check the occurs. Figure 6-47 Linkage Method  Audible Warning Trigger the audible warning locally. And it only supported by the device have the audio output.  Notify Surveillance Center Send an exception or alarm signal
  • Hikvision DS-2CD2532F-IS | User Manual - Page 86
    User Manual of Network Camera  The captured image can also be uploaded to the available SD card or network disk.  Trigger  Day/Night Switch OFF Steps: (1)Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. (2)Select OFF for Switch Day and Night Settings. 86
  • Hikvision DS-2CD2532F-IS | User Manual - Page 87
    User Manual of Network Camera (3)Select the area by clicking the area No Night Auto-Switch Steps: (1)Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. (2)Select Auto-Switch for Switch Day and Night Settings. Figure 6-49 Day/Night Auto-Switch (3)Select the area
  • Hikvision DS-2CD2532F-IS | User Manual - Page 88
    User Manual of Network Camera mode. (7)Click Save to save the settings.  Day/Night Scheduled-Switch (1)Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. (2)Select Scheduled-Switch for Switch Day and Night Settings. Figure 6-50 Day/Night Scheduled-Switch (3)
  • Hikvision DS-2CD2532F-IS | User Manual - Page 89
    User Manual of Network Camera Figure 6-51 Video Tampering Alarm 2. Check Enable Video Tampering checkbox to enable the video tampering detection. 3. Set the video tampering area. Refer
  • Hikvision DS-2CD2532F-IS | User Manual - Page 90
    User Manual of Network Camera 2. Choose the alarm input No. and the Alarm Type. The alarm type can be NO (Normally Open) and NC (Normally Closed). Edit
  • Hikvision DS-2CD2532F-IS | User Manual - Page 91
    . You can also set a name for the alarm output (optional). 3. The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or Manual. The delay time refers to the time duration that the alarm output remains in effect after alarm occurs. 4. Click Edit to enter the Edit Schedule
  • Hikvision DS-2CD2532F-IS | User Manual - Page 92
    User Manual of Network Camera 1. Enter the Exception Settings interface: Configuration > Advanced Alarm 2. Select the wireless alarm number. Up to 8 channels of external wireless alarm input are supported. 3. Check the checkbox of Enable Wireless Alarm to activate the wireless alarm. 4. Input the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 93
    User Manual of Network Camera 6. Click Save to save the settings. 7. Locate the desired. 4. Check the checkbox to select the linkage methods taken for the PIR alarm. 5. Click the Edit button to set the arming schedule. 6. Click Save to save the settings. 7. Go to Configuration > Advanced
  • Hikvision DS-2CD2532F-IS | User Manual - Page 94
    User Manual of Network Camera Figure 6-56 Configuring PIR Alarm Settings  Emergency Alarm Purpose: You can press the Emergency button on the remote control to trigger the Emergency Alarm in case of an emergency. Note: The remote control is required for the Emergency Alarm. Go
  • Hikvision DS-2CD2532F-IS | User Manual - Page 95
    User Manual of Network Camera Figure 6-57 Configuring Emergency Alarm Settings 6.6.7 Configuring Audio Exception Detection Purpose: Audio exception detection function detects the abnormal sounds in the surveillance
  • Hikvision DS-2CD2532F-IS | User Manual - Page 96
    User Manual of Network Camera  Sound Intensity Threshold: Range [1-100], it can the real environment. 5. You can view the real-time volume of the sound. 6. Click the Edit button to set the arming schedule. 7. Select the linkage methods for audio exception, including Notify Surveillance Center, Send
  • Hikvision DS-2CD2532F-IS | User Manual - Page 97
    User Manual of Network Camera 4. Select the linkage methods for defocus, including the value is, the more easily the change of scene can trigger the alarm. 4. Click the Edit button to set the arming schedule. 5. Select the linkage methods for scene change, including Notify Surveillance Center, Send
  • Hikvision DS-2CD2532F-IS | User Manual - Page 98
    User Manual of Network Camera Figure 6-60 Configuring Scene Change Detection 6.6.10 Configuring Face Detection Purpose: Face detection function detects the face appears in the surveillance scene,
  • Hikvision DS-2CD2532F-IS | User Manual - Page 99
    User Manual of Network Camera 5. Click the Edit button to set the arming schedule. 6. Select the linkage methods for face detection, including Notify Surveillance Center, Send Email, Upload to FTP, Trigger Channel and Trigger
  • Hikvision DS-2CD2532F-IS | User Manual - Page 100
    User Manual of Network Camera 1. Enter the Line Crossing Detection settings interface: Configuration the function. 3. Select the line from the drop-down list for detection settings. 4. Click the Draw Area button, and a virtual line is displayed on the live video. 5. Click-and-drag the line, and you
  • Hikvision DS-2CD2532F-IS | User Manual - Page 101
    User Manual of Network Camera Figure 6-62 Draw Crossing Line 6.6.12 Configuring Intrusion function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the detection
  • Hikvision DS-2CD2532F-IS | User Manual - Page 102
    User Manual of Network Camera 6. Set the time threshold, detection sensitivity and object percentage Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 8. Click the Edit button to set the arming schedule. 9. Select the linkage methods for intrusion detection
  • Hikvision DS-2CD2532F-IS | User Manual - Page 103
    User Manual of Network Camera 6.6.13 Configuring Region Entrance Detection Purpose: Region entrance detection Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of
  • Hikvision DS-2CD2532F-IS | User Manual - Page 104
    User Manual of Network Camera Figure 6-64 Configuring Region Entrance Detection 6.6.14 Configuring function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 105
    User Manual of Network Camera object which can trigger the alarm. When the sensitivity is high, a very small object exiting from the region can trigger the alarm. 7. Repeat the above steps to configure other regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined
  • Hikvision DS-2CD2532F-IS | User Manual - Page 106
    User Manual of Network Camera 1. Enter the Unattended Baggage Detection settings interface: Configuration> . 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 107
    User Manual of Network Camera Figure 6-66 Configuring Unattended Baggage 6.6.16 Configuring function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 108
    User Manual of Network Camera 6. Set the time threshold and detection sensitivity for object regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 8. Click the Edit button to set the arming schedule. 9. Select the linkage methods for object removal
  • Hikvision DS-2CD2532F-IS | User Manual - Page 109
    User Manual of Network Camera 6.7 VCA Configuration 6.7.1 Behavior Analysis The behavior analysis detects a series of suspicious behavior, and certain linkage methods will be enabled if the alarm
  • Hikvision DS-2CD2532F-IS | User Manual - Page 110
    Data: Input the mounting height, viewing angle, and horizon ratio of the camera manually. Draw on Live View Video: Click Draw Verification Line (Horizontal) / ( / Vertical Verify button to draw a horizontal / vertical line on the live video, and then click the Calibrate button to calculate the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 111
    User Manual of Network Camera Figure 6-69 Draw on Live View Window  Shield Region The shield region allows you to set the specific region in which the behavior analysis will not function. Up to 4 shield regions are supported. Steps: 1. Click Shield Region tab to enter the shield region
  • Hikvision DS-2CD2532F-IS | User Manual - Page 112
    User Manual of Network Camera 3. Click Save to save the settings.  Rule The behavior analysis supports a series of behaviors, including line crossing detection, intrusion, region entrance, and region exiting, etc. Note: Please refer to each chapter for detailed information of each
  • Hikvision DS-2CD2532F-IS | User Manual - Page 113
    User Manual of Network Camera Steps: 1. Click Rule Tab to enter the rule configuration interface. 2. Check the checkbox of the Up to 8 single rules and 2 combined rules are configurable. And the line crossing, intrusion, region exiting and region entrance are supported for the combined rules. 113
  • Hikvision DS-2CD2532F-IS | User Manual - Page 114
    User Manual of Network Camera 6. Click Save to save the settings. 7. Click Arming . The higher the value, the easier a target be recognized, and the higher the misinformation is. The default value of 3 is recommended. Background Update Rate [0~4]: It refers to the speed of the new scene replaces
  • Hikvision DS-2CD2532F-IS | User Manual - Page 115
    User Manual of Network Camera Restore Default: Click to restore the configured parameters to the default. Restart VCA: Restart the algorithms library of behavior analysis. ● Global Size Filter Note: Compared with the size filter under rule, which is aiming at each
  • Hikvision DS-2CD2532F-IS | User Manual - Page 116
    User Manual of Network Camera 6.7.2 Face Capture Face capture can capture the face to set the specific region in which the face capture will not function. Up to 4 shield regions are supported. Steps: 1. Click Shield Region tab to enter the shield region configuration interface. 2. Click Draw Area.
  • Hikvision DS-2CD2532F-IS | User Manual - Page 117
    Manual of to finish the area drawing. Notes:  Polygon area (4~10 sides) sides is supported.  If the live view is stopped, there is no way to draw the the misinformation of the faces in the wall painting or posters. The default value of 3 is recommended. Capture Times [1~10]: Refers to the capture
  • Hikvision DS-2CD2532F-IS | User Manual - Page 118
    is. Minimum Duration [1~60min]: The minimum duration of the camera exposures the face. The default value is 1 minute. Note: If the face exposure is enabled, please make sure the WDR function is disabled, and the manual iris is selected. Enable Face ROI: If the camera captures a face, the face area
  • Hikvision DS-2CD2532F-IS | User Manual - Page 119
    User Manual of Network Camera Figure 6-73 Advanced Configuration 6.7.3 Heat Map Heat map is a graphical representation of data represented by colors. The heat map function of the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 120
    User Manual of Network Camera Figure 6-74 Heat Map Configuration 2. Select Heat Map target. The over-high sensitivity may cause the misinformation. It is recommended you set the sensitivity as the default value, which is 50. Background Update Rate [0~100]: It refers to the speed of the new scene
  • Hikvision DS-2CD2532F-IS | User Manual - Page 121
    Manual of Network Camera misinformation. The default level is 50. Minimum Target Size [0~100]: It refers to the size of the camera identify a target. You can set the target size according to the actual environment. The default , there is an Export button to export the data in an excel file. 121
  • Hikvision DS-2CD2532F-IS | User Manual - Page 122
    User Manual of Network Camera Figure 6-75 Space Heat Map Notes:  As shown in the configured area and is widely applied to the entrances or exits. Notes:  People counting function is supported by some certain iDS camera models.  It is recommended to install the camera vertically to the ground
  • Hikvision DS-2CD2532F-IS | User Manual - Page 123
    User Manual of Network Camera Steps: 1. Enter the People Counting Configuration interface: of the detection line to adjust its length. 4) To delete the detection line, click the Delete Line button. Note: The detection line should cover the whole entrance / exit. 6. An arrow indicating the entering
  • Hikvision DS-2CD2532F-IS | User Manual - Page 124
    User Manual of Network Camera detection line is selected. You can click the Change Direction button to adjust the arrow direction to opposite side. 7. Check the checkbox of Camera Calibration to enable the function. 8. Click the Reset Counter button, and the number of the people entered and exited
  • Hikvision DS-2CD2532F-IS | User Manual - Page 125
    User Manual of Network Camera Figure 6-77 Statistics Result Note: It is recommended that you do not adjust the electronic lens after the installation is completed, which may cause the inaccuracy of the data in some degree. 125
  • Hikvision DS-2CD2532F-IS | User Manual - Page 126
    User Manual of Network Camera Chapter 7 Storage Settings Before you start: To configure record settings, please make sure that you path. (3) Select the mounting type. NFS and SMB/CIFS are selectable. And you can set the user name and password to guarantee the security if SMB/CIFS is selected. 126
  • Hikvision DS-2CD2532F-IS | User Manual - Page 127
    Camera Note: Please refer to the User Manual of NAS for creating the file path.  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing
  • Hikvision DS-2CD2532F-IS | User Manual - Page 128
    recording, refer to Section 5.3 Recording and Capturing Pictures Manually. In this section, you can follow the instructions to configure the scheduled recording. By default, the record files of scheduled recording are stored in the SD card (if supported) or in the network disk. Steps: 1. Enter the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 129
    User Manual of Network Camera Configuration > Advanced Configuration> Storage > Record Schedule Figure 7-5 starts to record at 9:59:55. The Pre-record time can be configured as No Pre-record, 5 s, 10 s, 15 s, 20 s, 25 s, 30 s or not limited.  Post-record: The time you set to stop recording after the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 130
    User Manual of Network Camera The Post-record time can be configured as 5 s, 10 s, 30 s, 1 min, 2 min, 5 min or 10 min. Note: The record parameter configurations vary
  • Hikvision DS-2CD2532F-IS | User Manual - Page 131
    User Manual of Network Camera to the time of the schedule.  Record Triggered by Motion Detection If you select Motion Detection, the video will be recorded when
  • Hikvision DS-2CD2532F-IS | User Manual - Page 132
    User Manual of Network Camera Figure 7-8 Edit Record Schedule (3) Check the checkbox of snapshot and event-triggered snapshot. The captured picture can be stored in the SD card (if supported) or the netHDD (For detailed information about netHDD, please refer to Section 7.1 Configuring NAS Settings
  • Hikvision DS-2CD2532F-IS | User Manual - Page 133
    Manual of Network Camera Check the Enable Event-triggered Snapshot checkbox to check event-triggered snapshot. 3. Select the quality of the snapshot. 4. Set the time interval between two snapshots. 5. Click Save to save the settings. Uploading to FTP You can follow below configuration instructions
  • Hikvision DS-2CD2532F-IS | User Manual - Page 134
    User Manual of Network Camera Figure 7-9 Snapshot Settings 7.4 Configuring Lite Storage Purpose: When there is no moving object in the monitoring scenario, the frame rate and bitrate
  • Hikvision DS-2CD2532F-IS | User Manual - Page 135
    been switched into the Cloud Storage working mode, refer to the User Manual of NVR for details. Steps: 1. Enter the Cloud Storage interface: port of the storage server. 4. Input the user name, password and confirm password for the authentication of the storage server.  For your privacy
  • Hikvision DS-2CD2532F-IS | User Manual - Page 136
    User Manual of Network Camera  Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 5. Input picture storage pool ID of the server. 6. (Optional) You can
  • Hikvision DS-2CD2532F-IS | User Manual - Page 137
    User Manual of Network Camera Chapter 8 Counting Purpose: Counting function is used to calculate the number of object entered or exited a certain configured area and is widely applied to the entrances or exits. Notes:  Counting function is supported by some certain non-iDS camera models.  Compared
  • Hikvision DS-2CD2532F-IS | User Manual - Page 138
    User Manual of Network Camera Figure 8-1 Counting Configuration 2. Select Counting Configuration To delete the detection line, click the Delete Line button. Note: The detection line should cover the whole entrance / exit. 6. Click the Reset Counter button, and the number of the people entered and
  • Hikvision DS-2CD2532F-IS | User Manual - Page 139
    User Manual of Network Camera export the data in an excel file. Figure 8-2 Statistics Result 139
  • Hikvision DS-2CD2532F-IS | User Manual - Page 140
    User Manual of Network Camera Chapter 9 Road Traffic Purpose: Vehicle Detection and Mixed-traffic Detection are available for the road traffic monitoring. In Vehicle Detection, the passed
  • Hikvision DS-2CD2532F-IS | User Manual - Page 141
    User Manual of Network Camera 1) To edit the arming schedule, click Edit button. 2) Choose the day you want to set the arming schedule. 3) Click to set the time period for the arming schedule. 4) (Optional) After you set the arming schedule, you can click the Copy button to copy the schedule to
  • Hikvision DS-2CD2532F-IS | User Manual - Page 142
    User Manual of Network Camera  Configuring the Upload Picture 1. Set the picture vehicle color, etc. You can also click the up and down direction buttons to adjust the sequence of the text. 4. Click the Save button to activate the settings. Figure 9-2 Upload Picture Settings  Configuring the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 143
    User Manual of Network Camera Figure 9-3 Overlay Content Settings 143
  • Hikvision DS-2CD2532F-IS | User Manual - Page 144
    User Manual of Network Camera Chapter 10 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD
  • Hikvision DS-2CD2532F-IS | User Manual - Page 145
    User Manual of Network Camera Button Figure 10-3 Playback Toolbar Table 10-1 Description of the buttons Operation Button Operation Play Capture a picture Pause Start/Stop clipping video / files Stop / Audio on and adjust volume/Mute Speed down Speed up Playback by frame /
  • Hikvision DS-2CD2532F-IS | User Manual - Page 146
    User Manual of Network Camera Chapter 11 Log Searching Purpose: The operation, alarm, exception and information of the camera can be stored in log files. You can
  • Hikvision DS-2CD2532F-IS | User Manual - Page 147
    User Manual of Network Camera 4. To export the log files, click Save log to save the log files in your computer. 147
  • Hikvision DS-2CD2532F-IS | User Manual - Page 148
    User Manual of Network Camera Chapter 12 Others 12.1 Managing User Accounts Enter the a User The admin user has all permissions by default and can create / modify / delete other accounts. The admin user cannot be deleted and you can only change the admin password. Steps: 1. Click Add to add a user.
  • Hikvision DS-2CD2532F-IS | User Manual - Page 149
    User Manual of Network Camera ● Proper configuration of all passwords and other security settings is the select the user from the list and click Modify. 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 150
    User Manual of Network Camera  Deleting a User Steps: Figure 12-3 Modify a User 1. Click to select the user you want to delete and click Delete. 2. Click OK on
  • Hikvision DS-2CD2532F-IS | User Manual - Page 151
    User Manual of Network Camera 2. Select the RTSP Authentication type basic or disable in the settings. 12.3 Anonymous Visit Enabling this function allows visit for whom doesn't have the user name and password of the device. Note: Only live view is available for the anonymous user. Steps: 1. Enter the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 152
    User Manual of Network Camera critical when permitting the Anonymous "Live View" function to ensure that your camera's field of view does not impact the privacy of
  • Hikvision DS-2CD2532F-IS | User Manual - Page 153
    User Manual of Network Camera Figure 12-8 Add an IP (3) Click the OK to finish adding.  Modify Clear to delete all the IP addrsses. 5. Click Save to save the settings. 12.5 Security Service To enable the remote login, and improve the data communication security, the camera provides the security
  • Hikvision DS-2CD2532F-IS | User Manual - Page 154
    12-10 Security Service 2. Check the checkbox of Enable SSH to enable the data communication security, and uncheck the checkbox to disable the SSH. 3. Check the checkbox of Enable Illegal Login Lock, and then the device will be locked if you input the incorrect user name or password for 5 continuous
  • Hikvision DS-2CD2532F-IS | User Manual - Page 155
    User Manual of Network Camera Figure 12-11 Device Information 12.7 Maintenance 12.7.1 Rebooting the Camera Reboot to reboot the network camera. Figure 12-12 Reboot the Device 12.7.2 Restoring Default Settings Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System >
  • Hikvision DS-2CD2532F-IS | User Manual - Page 156
    User Manual of Network Camera Figure 12-13 Restore Default Settings Note: After restoring the default settings, the IP address is also restored to the default IP address, please be careful for this action. 12.7.3 Exporting / Importing Configuration File Purpose: Configuration file is used for the
  • Hikvision DS-2CD2532F-IS | User Manual - Page 157
    User Manual of Network Camera 12.7.4 Upgrading the System Steps: 1. Enter the Maintenance interface: to select the local upgrade file and then click Upgrade to start remote upgrade. Figure 12-15 Remote Upgrade Note: The upgrading process will take 1~10 minutes. Please don't disconnect power
  • Hikvision DS-2CD2532F-IS | User Manual - Page 158
    User Manual of Network Camera Figure 12-16 RS-232 Settings Note: If you want to connect System > RS485 Figure 12-17 RS-485 Settings 2. Set the RS-485 parameters and click Save to save the settings. By default, the Baud Rate is set as 9600 bps, the Data Bit is 8, the stop bit is 1 and the Parity and
  • Hikvision DS-2CD2532F-IS | User Manual - Page 159
    User Manual of Network Camera 12.10 Service Settings Go to Configuration> Advanced Configuration> System > Service to enter the service settings interface. Service settings refer to the hardware service the camera supports, and it varies according to the different cameras. For the cameras support IR
  • Hikvision DS-2CD2532F-IS | User Manual - Page 160
    User Manual of Network Camera Appendix Appendix 1 SADP Software Introduction  Description of SADP online devices automatically After launch the SADP software, it automatically searches the online devices every 15 seconds from the subnet where your computer locates. It displays the total number and
  • Hikvision DS-2CD2532F-IS | User Manual - Page 161
    15 seconds after it went online; it will be removed from the list in 45 seconds after it went offline.  Search online devices manually You can also click to refresh the online device list manually use of strong passwords for all functions and network devices. The password should be something of
  • Hikvision DS-2CD2532F-IS | User Manual - Page 162
    User Manual of Network Camera Figure A.1.2 Modify Network Parameters 162
  • Hikvision DS-2CD2532F-IS | User Manual - Page 163
    User Manual of Network Camera Appendix 2 Port Mapping The following settings are for TP settings. Figure A.2.2 Set the LAN parameters 3. Set the port mapping in the virtual severs of Forwarding. By default, camera uses port 80, 8000 and 554. You can change these ports value with web browser or client
  • Hikvision DS-2CD2532F-IS | User Manual - Page 164
    User Manual of Network Camera another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings
  • Hikvision DS-2CD2532F-IS | User Manual - Page 165
    User Manual of Network Camera 165
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
User Manual of Network Camera
1
User Manual
UD.6L0201D1919A01
Network Camera