Hikvision DS-2CD2232-I5 User Manual

Hikvision DS-2CD2232-I5 Manual

Get Hikvision DS-2CD2232-I5 PDF manuals and user guides View all Hikvision DS-2CD2232-I5 manuals
Add to My Manuals
Save this manual to your list of manuals

Hikvision DS-2CD2232-I5 manual content summary:

  • Hikvision DS-2CD2232-I5 | User Manual - Page 1
    User Manual of Network Camera Network Camera User Manual UD.6L0201D1673A01 0
  • Hikvision DS-2CD2232-I5 | User Manual - Page 2
    of Network Camera User Manual ©2015 Hangzhou Hikvision Digital Technology Co., Ltd. This user manual is intended for users of Network Camera (V5.2.6). It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that
  • Hikvision DS-2CD2232-I5 | User Manual - Page 3
    User Manual of Network Camera SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR using this product for surveillance purposes to ensure that your use of this product conforms. Support Should you have any questions, please do not hesitate to contact your local dealer. 2
  • Hikvision DS-2CD2232-I5 | User Manual - Page 4
    User Manual of Network Camera Regulatory Information FCC Information FCC compliance: This equipment radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
  • Hikvision DS-2CD2232-I5 | User Manual - Page 5
    ceiling can support more than 50(N) Newton gravities if the camera is fixed to the ceiling.  If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused
  • Hikvision DS-2CD2232-I5 | User Manual - Page 6
    User Manual of Network Camera Cautions:  Make sure the power supply voltage is proper may result in hazard of explosion. Please use the manufacturer recommended battery type. CHANGE THE DEFAULT PASSWORD The default password (12345) for the Admin account is is for first-time log-in purposes only. You
  • Hikvision DS-2CD2232-I5 | User Manual - Page 7
    User Manual of Network Camera Notes: For the camera supports IR, you are required to pay attention to the following precautions to prevent IR reflection:  Dust or grease on the dome cover will cause IR
  • Hikvision DS-2CD2232-I5 | User Manual - Page 8
    Manual of Network Camera Table of Contents Chapter 1 System Requirement 10 Chapter 2 Network Connection 11 2.1 Setting the Network Camera over the LAN 11 2.1.1 Wiring over the LAN ...11 2.1.2 Detecting and Changing the IP Address 12 2.2 Setting the Network Camera over the WAN 13 2.2.1 Static IP
  • Hikvision DS-2CD2232-I5 | User Manual - Page 9
    User Manual of Network Camera 6.3.7 6.3.8 6.3.9 6.3.10 6.3.11 6.3.12 6.3.13 6.3.14 Configuring QoS Settings 48 Configuring UPnP™ Settings 48 Configuring Wireless Dial Settings 49 Email Sending Triggered by Alarm 52 Configuring NAT (Network Address Translation) Settings 54 Configuring FTP
  • Hikvision DS-2CD2232-I5 | User Manual - Page 10
    User Manual of Network Camera 6.7 VCA Configuration 109 6.7.1 Behavior Analysis ...109 6.7.2 Face Capture ...115 12.4 IP Address Filter 151 12.5 Security Service 153 12.6 Viewing Device Information 154 12.7 Maintenance 154 12.7.1 Rebooting the Camera 154 12.7.2 Restoring Default Settings 155
  • Hikvision DS-2CD2232-I5 | User Manual - Page 11
    User Manual of Network Camera Chapter 1System Requirement Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium
  • Hikvision DS-2CD2232-I5 | User Manual - Page 12
    User Manual of Network Camera Chapter 2 Network Connection Before you start:  If you the same subnet with your computer, and install the SADP or iVMS-4200 software to search and change the IP of the network camera. Note: For the detailed introduction of SADP, please refer to Appendix 1. 2.1.1
  • Hikvision DS-2CD2232-I5 | User Manual - Page 13
    of your computer. 3. Enter the IP address of network camera in the address field of the web browser to view the live video. Notes: The default IP address is 192.0.0.64 and the port number is 8000. YOU MUST CHANGE THE DEFAULT PASSWORD - The default Admin account password (12345) is for first-time
  • Hikvision DS-2CD2232-I5 | User Manual - Page 14
    section explains how to connect the network camera to the WAN with a static IP or a dynamic IP. 2.2.1 Static IP Connection Before you start: Please apply a static IP from an ISP (Internet Service Provider). With the static IP address, you can connect the network camera via a router or connect it to
  • Hikvision DS-2CD2232-I5 | User Manual - Page 15
    2.1.2 Detecting and Changing the IP Address for detailed IP address configuration of the camera. Figure 2-5 Accessing the Camera with Static IP Directly 2.2.2 Dynamic IP Connection Before you start: Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect the network
  • Hikvision DS-2CD2232-I5 | User Manual - Page 16
    router. 7. Visit the camera via the applied domain name.  Connecting the network camera via a modem Purpose: This camera supports the PPPoE auto dial-up function. The camera gets a public IP address by ADSL dial-up after the camera is connected to a modem. You need to configure the PPPoE parameters
  • Hikvision DS-2CD2232-I5 | User Manual - Page 17
    User Manual of Network Camera  Normal Domain Name Resolution Figure 2-7 Normal Domain Name Resolution Figure 2-8 Private Domain Name Resolution Steps: 1. Install and run the IP Server software in a computer with a static IP. 2. Access the network camera through the LAN with a web browser or
  • Hikvision DS-2CD2232-I5 | User Manual - Page 18
    the IP address of the network camera in the address bar, e.g., 192.0.0.64 and press the Enter key to enter the login interface. 3. Input the user name and password and click Login. Note: Figure 3-1 Login Interface YOU MUST CHANGE THE DEFAULT PASSWORD -- The default Admin account password (12345
  • Hikvision DS-2CD2232-I5 | User Manual - Page 19
    User Manual of Network Camera Figure 3-3 Install Plug-in (1) Figure 3-4 Install Plug-in (2) Note: You may have to close the web browser to install the plug-in.
  • Hikvision DS-2CD2232-I5 | User Manual - Page 20
    User Manual of Network Camera Figure 3-5 iVMS-4200 Control Panel Figure 3-6 iVMS-4200 Main View Note: For detailed information about the software, please refer to the user manual of the iVMS-4200. 19
  • Hikvision DS-2CD2232-I5 | User Manual - Page 21
    User Manual of Network Camera Chapter 4 Wi-Fi Settings Purpose: By connecting to the wireless network, you don't need to use cable of any kind for network
  • Hikvision DS-2CD2232-I5 | User Manual - Page 22
    Network mode as Manage, and the Security mode of the network is automatically shown when you select the wireless network, please don't change it manually. Note: These parameters are exactly identical with those of the router. 5. Enter the key to connect the wireless network. The key should be that
  • Hikvision DS-2CD2232-I5 | User Manual - Page 23
    User Manual of Network Camera Figure 4-5 Ad-hoc Connection Point 6. Choose the SSID and connect. Security Mode Description: Figure 4-6 Security Mode You can choose the Security Mode
  • Hikvision DS-2CD2232-I5 | User Manual - Page 24
    User Manual of Network Camera the method used by your access point. Not key types available depend on the access point being used. The following options are available: HEX - Allows you to manually enter the hex key. ASCII - In this method the string must be exactly 5 characters for 64-bit WEP and
  • Hikvision DS-2CD2232-I5 | User Manual - Page 25
    User Manual of Network Camera Figure 4-9 EAP-TLS  Identity - Enter the user ID to present to the network.  Private key password - Enter the password for your user ID.  EAPOL version - Select the version used (1 or 2) in your access point.  CA Certificates - Upload a CA certificate to present to
  • Hikvision DS-2CD2232-I5 | User Manual - Page 26
    User Manual of Network Camera 4.2 Easy Wi-Fi button on the configuration interface of the IE browser), on both the Access Point (and a registrar of the network) and the new wireless client device. 1. Check the checkbox of to enable WPS. 2. Choose the connection mode as PBC. Note: Support
  • Hikvision DS-2CD2232-I5 | User Manual - Page 27
    Manual of Network Camera connecting devices. 3. Check on the Wi-Fi router to see if there is a WPS button. If yes push the button and you can see the indicator near the button start flashing, which means the WPS function of the router is enabled. For detailed operation, please see the user guide
  • Hikvision DS-2CD2232-I5 | User Manual - Page 28
    User Manual of Network Camera Figure 4-11 Wi-Fi Settings - WPS PIN Mode 2. to the router, in the example, enter 48167581 to the router. 4.3 IP Property Settings for Wireless Network Connection The default IP address of wireless network interface controller is 192.168.1.64. When you connect the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 29
    > Basic Configuration> Network> TCP/IP Figure 4-12 TCP/IP Settings 2. Select the NIC as wlan. 3. Customize the IPv4 address, the IPv4 Subnet Mask and the Default Gateway. The setting procedure is the same with that of LAN. If you want to be assigned the IP address you can check the checkbox to
  • Hikvision DS-2CD2232-I5 | User Manual - Page 30
    User Manual of Network Camera Chapter 5 Live View 5.1 Live View Page Purpose: The It lists the camera model you are connecting to. Online Help: Click to get the online help, which will guide you through the basic operations for each function. Menu Bar: Click each tab to enter Live View, Playback,
  • Hikvision DS-2CD2232-I5 | User Manual - Page 31
    layout and the stream type of the live view. And you can click the drop-down to select the plug-in. For IE (internet explorer) user, webcomponents and quick time are selectable. And for Non-IE user, webcomponents, quick time, VLC or MJPEG is selectable if they are supported by the web
  • Hikvision DS-2CD2232-I5 | User Manual - Page 32
    function. Note: The third stream and 3D positioning require the support of camera. 5.3 Recording and Capturing Pictures Manually In the live view interface In the live view interface, you can use the PTZ control buttons to realize pan/tilt/zoom control of the camera. Before you start: To
  • Hikvision DS-2CD2232-I5 | User Manual - Page 33
    Manual of Network Camera Click the direction buttons to control the pan/tilt movements. Figure 5-3 PTZ Control Panel Click the zoom/iris/focus buttons relative positions.  For the cameras which support lens movements only, the direction buttons are invalid. Table 5-2 Descriptions of PTZ Control
  • Hikvision DS-2CD2232-I5 | User Manual - Page 34
    User Manual of Network Camera Figure 5-4 Setting a Preset 2. Use the PTZ control buttons to move the lens to the desired  Calling a Preset: This feature enables the camera to point to a specified preset scene manually or when an event takes place. For the defined preset, you can call it at any
  • Hikvision DS-2CD2232-I5 | User Manual - Page 35
    User Manual of Network Camera 5.4.3 Setting / Calling a Patrol Note: No less than 2 presets have to be configured before you set a patrol. Steps: 1. Click to enter the patrol
  • Hikvision DS-2CD2232-I5 | User Manual - Page 36
    User Manual of Network Camera Chapter 6 Network Camera Configuration 6.1 Configuring Local  Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable. TCP: Ensures complete delivery of streaming data and better video quality, yet the real-time transmission will be affected. UDP: Provides real-
  • Hikvision DS-2CD2232-I5 | User Manual - Page 37
    streaming under some network environments. MULTICAST: It's recommended to select MCAST type when using the Multicast function. For detailed information about Multicast, refer to Section 6.3.1 Configuring TCP/IP to: Set the saving path for the manually recorded video files.  Save downloaded files to
  • Hikvision DS-2CD2232-I5 | User Manual - Page 38
    User Manual of Network Camera 6.2 Configuring Time Settings Purpose: You can follow the instructions in this section to configure the time checkbox to enable the NTP function. (2) Configure the following settings: Server Address: IP address of NTP server. NTP Port: Port of NTP server. Interval: The
  • Hikvision DS-2CD2232-I5 | User Manual - Page 39
    as the server at the National Time Center (IP Address: 210.72.145.44). If the camera is set in a customized network, NTP software can be used to establish a NTP server for time synchronization.  Synchronizing Time Synchronization Manually Enable the Manual Time Sync function and then click to set
  • Hikvision DS-2CD2232-I5 | User Manual - Page 40
    > Basic Configuration > Network > TCP/IP Or Configuration > Advanced Configuration > Network > TCP/IP Figure 6-6 TCP/IP Settings 2. Configure the basic network settings, including the NIC Type, IPv4 or IPv6 Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings 39
  • Hikvision DS-2CD2232-I5 | User Manual - Page 41
    Manual of Network Camera and Multicast Address stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address port, RTSP port, HTTPS port and server port of the camera. HTTP Port: The default port number
  • Hikvision DS-2CD2232-I5 | User Manual - Page 42
    Manual of Network Camera ranges from 1024 to 65535. HTTPS Port: The default port number is 443, and it can be changed to any port No. which is not occupied. Server Port: The default Enter User Name, Password, and Confirm password for PPPoE access. Note: The User Name and Password should be assigned
  • Hikvision DS-2CD2232-I5 | User Manual - Page 43
    Manual of Network Camera 6.3.4 Configuring DDNS Settings Purpose: If your camera is set to use PPPoE as its default use of strong passwords for all functions and network devices. The password should be something of , NO-IP, and DynDNS.  DynDNS: Steps: (1)Enter Server Address of DynDNS (e.g. members.dyndns
  • Hikvision DS-2CD2232-I5 | User Manual - Page 44
    website. (3)Enter the Port of DynDNS server. (4)Enter the User Name and Password registered on the DynDNS website. (5)Click Save to save the settings. Figure 6-10 DynDNS Settings  IP Server: Steps: (1) Enter the Server Address of the IP Server. (2) Click Save to save the settings. Note: For the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 45
    User Manual of Network Camera (1)Choose the DDNS Type as NO-IP. Figure 6-12 NO-IP Settings (2) Enter the Server Address as www.noip.com (3) Enter the Domain name you registered. (4) Enter the Port number, if needed. (5) Enter the User Name and Password. (6) Click Save and then you can view the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 46
    User Manual to receive the camera information via SNMP port. By setting the Trap Address, the camera can send the alarm event and exception messages to the level you required. SNMP v1 provides no security and SNMP v2 requires password for access. And SNMP v3 provides encryption and if you use the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 47
    User Manual of Network Camera Figure 6-14 SNMP Settings 2. Check the corresponding version checkbox ( , , ) to enable the feature. 3. Configure the SNMP settings. Note: The settings of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 48
    User Manual of Network Camera 6.3.6 Configuring 802.1X Settings Purpose: The network camera supports IEEE 802.1X standard. IEEE The authentication server must be configured. Please apply and register a user name and password for 802.1X in the server. For your privacy and to better protect your
  • Hikvision DS-2CD2232-I5 | User Manual - Page 49
    Manual of Network Camera Note: The EAPOL version must be identical with that of the router or the switch. 4. Enter the user name and password priority is. Note: DSCP refers to the Differentiated Service Code Point; and the DSCP value is used in the IP header to indicate the priority of the data.
  • Hikvision DS-2CD2232-I5 | User Manual - Page 50
    is selected, you can set the offline time and manual dialing parameters. 2) Set the access number, user name, password, APN, MTU and verification protocol. You can also leave these parameters blank, and the device will adopt the default settings for dialing after other parameters are configured. 49
  • Hikvision DS-2CD2232-I5 | User Manual - Page 51
    selected, the network selection priority comes as: 4G > 3G > Wired Network. 4) Input the offline time if Manual is selected as the dial mode. 5) Input the UIM Number (Mobile Phone Number). 6) Click the Edit button to set the arming schedule if Auto is selected as the dial mode. 7) Click Save to save
  • Hikvision DS-2CD2232-I5 | User Manual - Page 52
    of Network Camera 4. View the dial status. 1) Click the Refresh button to view the dial status including real-time mode, UIM status, signal strength, etc. 2) If Manual is selected as the dial mode, you can also manually connect / disconnect the wireless network. Figure 6-19 Dial Status 5. Set the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 53
    User Manual of Network Camera Figure 6-21 SMS Alarm Settings 3) Input the mobile phone number Network > TCP/IP or Advanced Configuration > Network > TCP/IP before using the Email function. Steps: 1. Enter the TCP/IP Settings (Configuration > Basic Configuration > Network > TCP/IP or Configuration >
  • Hikvision DS-2CD2232-I5 | User Manual - Page 54
    User Manual of Network Camera set the IPv4 Address, IPv4 Subnet Mask, IPv4 Default Gateway and the Preferred DNS Server. Note: Please refer to Section 6.3.1 Configuring TCP/IP Settings for detailed information. 2. Enter the Email Settings interface: Configuration > Advanced Configuration > Network >
  • Hikvision DS-2CD2232-I5 | User Manual - Page 55
    passwords for all functions and network devices. The password should Receiver's Address: The email address of user to be notified. 4. default port numbers: Choose Port Mapping Mode as Auto. To port mapping with the customized port numbers: Choose Port Mapping Mode as Manual. And for manual
  • Hikvision DS-2CD2232-I5 | User Manual - Page 56
    User Manual of Network Camera Figure 6-23 Configure NAT Settings 3. Click Save to save the settings. 6.3.12 Configuring FTP Settings Purpose: You can configure the FTP server
  • Hikvision DS-2CD2232-I5 | User Manual - Page 57
    Manual of Network Camera 2. Configure the FTP settings; and the user name and password are required for login the FTP server. For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords or Device IP for the must be supported by the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 58
    User Manual of Network Camera simply leave the checkbox unchecked. Figure 6-25 Platform following steps to set the port number of https. E.g.: If you set the port number as 443 and the IP address is 192.0.0.64, you may access the device by inputting https://192.0.0.64:443 via the web browser. Steps
  • Hikvision DS-2CD2232-I5 | User Manual - Page 59
    User Manual of Network Camera  Create the self-signed certificate 1) Click Create button to enter the creation interface. Figure 6-27 Create Self-signed Certificate 2) Enter the country, host name/IP, validity and other information. 3) Click OK to save the settings. Note: If you already had a
  • Hikvision DS-2CD2232-I5 | User Manual - Page 60
    User Manual of Network Camera 6.4 Configuring Video and Audio Settings 6.4.1 Configuring Video Settings Steps the following parameters for the selected main stream or sub-stream: Video Type: Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded
  • Hikvision DS-2CD2232-I5 | User Manual - Page 61
    Manual the frequency at which the video stream is updated and it is measured by frames per second (fps). A Stream Type is set to main stream, H.264 and MPEG4 are selectable, and if the stream type is set to sub stream or third stream, H.264, MJPEG, and MPEG4 are selectable. Note: The supported
  • Hikvision DS-2CD2232-I5 | User Manual - Page 62
    User Manual of Network Camera lower value of the smoothing, the higher quality of the stream, though it may appear not fluent. 4. Click Save G.726, MP2L2 and PCM are selectable. For MP2L2, the sampling rate and audio stream bitrate are configurable; for PCM, the sampling rate can be set. Audio Input:
  • Hikvision DS-2CD2232-I5 | User Manual - Page 63
    User Manual of Network Camera 6.4.3 Configuring ROI Encoding Purpose: ROI (Region of Interest) encoding helps to discriminate the ROI and background information in video compression, which means,
  • Hikvision DS-2CD2232-I5 | User Manual - Page 64
    stream type for ROI encoding. 4. Select the region from the drop-down list for ROI settings. There are four fixed regions selectable. 5. Click the Draw Area button enable face tracking function, the face detection function should be supported and enabled. 3. Check the checkbox of Enable License Plate
  • Hikvision DS-2CD2232-I5 | User Manual - Page 65
    User Manual of Network Camera 6.4.4 Display Information on Stream Check the checkbox of Enable Dual-VCA, and the information of the objects (e.g. human, vehicle, etc.) will be marked in the video stream. And then you can set rules on the connected rear-end device to detect the events including line
  • Hikvision DS-2CD2232-I5 | User Manual - Page 66
    User Manual of Network Camera Figure 6-33 Target Cropping 6.5 Configuring Image Parameters 6.5.1 Configuring Display Settings Purpose: You can set the image quality of the camera, including brightness,
  • Hikvision DS-2CD2232-I5 | User Manual - Page 67
    from 1~100, and the default value is 50.  Exposure Settings If the camera is equipped with the fixed lens, only Manual is selectable, and the iris mode is not configurable. If Auto is selected, you can set the auto iris level from 0~ 100. For the camera supports
  • Hikvision DS-2CD2232-I5 | User Manual - Page 68
    ranges from 1 ~ 1/100,000s. Adjust it according to the actual luminance condition.  Focus Settings For the camera supports electronic lens, you can set the focus mode as Auto, Manual or Semi-auto. If auto is selected, the focus is adjusted automatically according to the actual monitoring scenario
  • Hikvision DS-2CD2232-I5 | User Manual - Page 69
    the IR LED, thus providing a clear image that is not overexposed or too dark. Select ON to enable the smart IR, and then Auto and Manual are selectable for IR mode. Select AUTO, and the power of IR LED changes automatically according to the actual luminance. E.g.: if the current scene is
  • Hikvision DS-2CD2232-I5 | User Manual - Page 70
    User Manual of Network Camera Figure 6-36 White Balance  Image Enhancement Digital Noise Reduction: DNR reduces the noise in the video stream. OFF, Normal Mode and Expert Mode are selectable. Set the DNR level from 0~100, and the default value is 50 in Normal Mode. Set the DNR level from both space
  • Hikvision DS-2CD2232-I5 | User Manual - Page 71
    User Manual of Network Camera Lens Distortion Correction: Select ON / OFF to enable / disable the lens distortion correction. The distorted image caused by the wide-angle lens can be corrected if this function enabled.  Other Some of the camera supports CVBS, SDI, or HDMI output. Please refer to
  • Hikvision DS-2CD2232-I5 | User Manual - Page 72
    User Manual of Network Camera Configuring OSD Settings Purpose: You can customize the camera name and time on the screen. Steps: 1. Enter the OSD Settings interface: Configuration >
  • Hikvision DS-2CD2232-I5 | User Manual - Page 73
    User Manual of Network Camera 6. You can use the mouse to click and drag the text frame live view window to adjust the OSD position. in the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 74
    User Manual of Network Camera Figure 6-41 Text Overlay 2. Check the checkbox in front of textbox to enable the on-screen display. 3. Input the characters in the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 75
    User Manual of Network Camera Figure 6-42 Privacy Mask Settings 4. Click and drag the mouse in the live video window to draw the mask area. Note: You
  • Hikvision DS-2CD2232-I5 | User Manual - Page 76
    User Manual of Network Camera Figure 6-43 Picture Overlay 2. Click Browse to select a picture. 3. Click Upload to upload detection, audio exception detection, intrusion detection, defocus detection, scene change detection, etc. A help document will guide you to go through the configuration steps. 75
  • Hikvision DS-2CD2232-I5 | User Manual - Page 77
    User Manual of Network Camera 6.6.1 Configuring Motion Detection Purpose: Motion detection detects the moving objects in the configured surveillance area, and a series of actions can be taken
  • Hikvision DS-2CD2232-I5 | User Manual - Page 78
    User Manual of Network Camera Figure 6-44 Enable Motion Detection (4)Click Draw Area. Click and drag the mouse on the live video to draw a motion detection area. (5)
  • Hikvision DS-2CD2232-I5 | User Manual - Page 79
    User Manual of Network Camera (3)Click to set the time period for the arming schedule. (4)(Optional) After you set the arming schedule, you can copy the schedule
  • Hikvision DS-2CD2232-I5 | User Manual - Page 80
    User Manual of Network Camera Trigger the audible warning locally. And it only supported by the device have the audio output is triggered and upload the picture to a FTP server. Notes:  Set the FTP address and the remote FTP server first. Refer to Section 6.3.12 Configuring FTP Settings for detailed
  • Hikvision DS-2CD2232-I5 | User Manual - Page 81
    User Manual of Network Camera area of each area for different day/night switch. Figure 6-48 Expert Mode of Motion Detection  Day/Night Switch OFF Steps: (1)Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. (2)Select OFF for Switch Day and Night Settings. (3)
  • Hikvision DS-2CD2232-I5 | User Manual - Page 82
    User Manual of Network Camera Figure 6-49 Day/Night Auto-Switch (3)Select the area by clicking -Switch (1)Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. (2)Select Scheduled-Switch for Switch Day and Night Settings. Figure 6-50 Day/Night Scheduled-Switch 81
  • Hikvision DS-2CD2232-I5 | User Manual - Page 83
    User Manual of Network Camera (3)Select the start time and the end time for the switch timing. (4)Select the area by clicking the area No. (5)Slide the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 84
    User Manual of Network Camera 3. Set the video tampering area. Refer to Task 1 Set the Motion Detection Area in Section 6.6.1. 4. Click Edit to edit the arming schedule
  • Hikvision DS-2CD2232-I5 | User Manual - Page 85
    User Manual of Network Camera 3. Click Edit to set the arming schedule for the output (optional). 3. The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or Manual. The delay time refers to the time duration that the alarm output remains in effect after alarm occurs. 4. Click Edit
  • Hikvision DS-2CD2232-I5 | User Manual - Page 86
    User Manual of Network Camera Figure 6-53 Alarm Output Settings 6.6.5 Handling Exception The exception type can be HDD full, HDD error, network disconnected, IP address conflicted and illegal login to the cameras. Steps: 1. Enter the Exception Settings interface: Configuration > Advanced
  • Hikvision DS-2CD2232-I5 | User Manual - Page 87
    User Manual of Network Camera 6.6.6 Configuring Other Alarm Note: Some certain cameras support Wireless Alarm, PIR (passive infrared wireless alarm number. Up to 8 channels of external wireless alarm input are supported. 3. Check the checkbox of Enable Wireless Alarm to activate the wireless alarm.
  • Hikvision DS-2CD2232-I5 | User Manual - Page 88
    User Manual of Network Camera  PIR Alarm Purpose: A PIR (Passive Infrared) alarm . 4. Check the checkbox to select the linkage methods taken for the PIR alarm. 5. Click the Edit button to set the arming schedule. 6. Click Save to save the settings. 7. Go to Configuration > Advanced Configuration
  • Hikvision DS-2CD2232-I5 | User Manual - Page 89
    User Manual of Network Camera  Emergency Alarm Purpose: You can press the Emergency button on the remote control to trigger the Emergency Alarm in case of an emergency. Note: The remote control is required for the Emergency Alarm. Go
  • Hikvision DS-2CD2232-I5 | User Manual - Page 90
    User Manual of Network Camera 2. Check the checkbox of Audio Loss Exception to the real environment. 5. You can view the real-time volume of the sound. 6. Click the Edit button to set the arming schedule. 7. Select the linkage methods for audio exception, including Notify Surveillance Center, Send
  • Hikvision DS-2CD2232-I5 | User Manual - Page 91
    User Manual of Network Camera 6.6.8 Configuring Defocus Detection Purpose: The image blur caused by defocus of the lens can be detected, and some certain actions can be
  • Hikvision DS-2CD2232-I5 | User Manual - Page 92
    User Manual of Network Camera Steps: 1. Enter the Scene Change Detection settings the value is, the more easily the change of scene can trigger the alarm. 4. Click the Edit button to set the arming schedule. 5. Select the linkage methods for scene change, including Notify Surveillance Center,
  • Hikvision DS-2CD2232-I5 | User Manual - Page 93
    User Manual of Network Camera Steps: 1. Enter the Face Detection settings interface: Configuration higher the value is, the more easily the face can be detected. 5. Click the Edit button to set the arming schedule. 6. Select the linkage methods for face detection, including Notify Surveillance
  • Hikvision DS-2CD2232-I5 | User Manual - Page 94
    User Manual of Network Camera Figure 6-61 Configuring Face Detection 6.6.11 Configuring Line Crossing Detection Purpose: Line crossing detection function detects people, vehicle or other objects which
  • Hikvision DS-2CD2232-I5 | User Manual - Page 95
    User Manual of Network Camera 3. Select the line from the drop-down list for detection settings. 4. Click the Draw Area button, and a virtual line is displayed on the live video. 5. Click-and-drag the line, and you can locate it on the live video as desired.
  • Hikvision DS-2CD2232-I5 | User Manual - Page 96
    User Manual of Network Camera Figure 6-62 Draw Crossing Line 6.6.12 Configuring Intrusion function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the detection
  • Hikvision DS-2CD2232-I5 | User Manual - Page 97
    User Manual of Network Camera 6. Set the time threshold, detection sensitivity and object percentage Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 8. Click the Edit button to set the arming schedule. 9. Select the linkage methods for intrusion detection
  • Hikvision DS-2CD2232-I5 | User Manual - Page 98
    User Manual of Network Camera 6.6.13 Configuring Region Entrance Detection Purpose: Region entrance function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 99
    User Manual of Network Camera Figure 6-64 Configuring Region Entrance Detection 6.6.14 Configuring function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 100
    User Manual of Network Camera object which can trigger the alarm. When the sensitivity is high, a very small object exiting from the region can trigger the alarm. 7. Repeat the above steps to configure other regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined
  • Hikvision DS-2CD2232-I5 | User Manual - Page 101
    User Manual of Network Camera Configuration> Advanced Configuration> Smart Event> Loitering Detection 2. Check the checkbox of Enable Loitering Detection to enable the function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region
  • Hikvision DS-2CD2232-I5 | User Manual - Page 102
    User Manual of Network Camera Figure 6-66 Configuring Loitering Detection 6.6.16 Configuring People function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 103
    User Manual of Network Camera 6. Set the object percentage for people gathering detection. Percentage: Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 8. Click the Edit button to set the arming schedule. 9. Select the linkage methods for people gathering
  • Hikvision DS-2CD2232-I5 | User Manual - Page 104
    User Manual of Network Camera Steps: 1. Enter the Fast Moving Detection settings interface: function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 105
    User Manual of Network Camera Figure 6-68 Configuring Fast Moving Detection 6.6.18 Configuring function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 106
    User Manual of Network Camera Sensitivity: Range [1-100]. The value of the sensitivity regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 8. Click the Edit button to set the arming schedule. 9. Select the linkage methods for parking detection,
  • Hikvision DS-2CD2232-I5 | User Manual - Page 107
    User Manual of Network Camera Steps: 1. Enter the Unattended Baggage Detection settings interface: function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 108
    User Manual of Network Camera Figure 6-70 Configuring Unattended Baggage 6.6.20 Configuring function. 3. Select the region from the drop-down list for detection settings. 4. Click the Draw Area button to start the region drawing. 5. Click on the live video to specify the four vertexes of the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 109
    User Manual of Network Camera 6. Set the time threshold and detection sensitivity for object regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 8. Click the Edit button to set the arming schedule. 9. Select the linkage methods for object removal
  • Hikvision DS-2CD2232-I5 | User Manual - Page 110
    User Manual of Network Camera 6.7 VCA Configuration 6.7.1 Behavior Analysis The behavior analysis : The captured target and the configured area will be framed on the alarm picture. Display VCA info. on Stream: The green frames will be displayed on the target if in a live view or playback. Note: Make
  • Hikvision DS-2CD2232-I5 | User Manual - Page 111
    Data: Input the mounting height, viewing angle, and horizon ratio of the camera manually. Draw on Live View Video: Click Draw Verification Line (Horizontal) / ( / Vertical Verify button to draw a horizontal / vertical line on the live video, and then click the Calibrate button to calculate the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 112
    User Manual of Network Camera Figure 6-73 Draw on Live View Window  Shield Region The shield region allows you to set the specific region in which the behavior analysis will not function. Up to 4 shield regions are supported. Steps: 1. Click Shield Region tab to enter the shield region
  • Hikvision DS-2CD2232-I5 | User Manual - Page 113
    User Manual of Network Camera 3. Click Save to save the settings.  Rule The behavior analysis supports a series of behaviors, including line crossing detection, intrusion, region entrance, and region exiting, etc. Note: Please refer to each chapter for detailed information of each
  • Hikvision DS-2CD2232-I5 | User Manual - Page 114
    User Manual of Network Camera Steps: 1. Click Rule Tab to enter the rule and 2 combined rules are configurable. And the line crossing, intrusion, region exiting and region entrance are supported for the combined rules. 6. Click Save to save the settings. 7. Click Arming Schedule tab, click Edit
  • Hikvision DS-2CD2232-I5 | User Manual - Page 115
    User Manual of Network Camera and click Save to save the settings. 8. Click Alarm value, the easier a target be recognized, and the higher the misinformation is. The default value of 3 is recommended. Background Update Rate [0~4]: It refers to the speed of the new scene replaces the previous scene.
  • Hikvision DS-2CD2232-I5 | User Manual - Page 116
    User Manual of Network Camera ● Global Size Filter Note: Compared with the size filter under rule, which is aiming at each rule, the global size filter is
  • Hikvision DS-2CD2232-I5 | User Manual - Page 117
    Manual of Network Camera uploaded with the captured picture as well. Figure 6-76 Face Capture  VCA Info Face Capture Version: It lists the version of the algorithms library. Display information includes the display on picture and display on stream 4 shield regions are supported. Steps: 1. Click
  • Hikvision DS-2CD2232-I5 | User Manual - Page 118
    User Manual of to finish the area drawing. Notes:  Polygon area (4~10 sides) sides is supported.  If the live view is stopped, there is no way to draw the the misinformation of the faces in the wall painting or posters. The default value of 3 is recommended. Capture Times [1~10]: Refers to the capture
  • Hikvision DS-2CD2232-I5 | User Manual - Page 119
    is. Minimum Duration [1~60min]: The minimum duration of the camera exposures the face. The default value is 1 minute. Note: If the face exposure is enabled, please make sure the WDR function is disabled, and the manual iris is selected. Enable Face ROI: If the camera captures a face, the face area
  • Hikvision DS-2CD2232-I5 | User Manual - Page 120
    User Manual of Network Camera 6.7.3 Heat Map Heat map is a graphical representation of data represented by colors. The heat map function of the camera usually be used
  • Hikvision DS-2CD2232-I5 | User Manual - Page 121
    User Manual of Network Camera recommended you set the sensitivity as the default value, which is 50. Background Update Rate [0~100]: It refers to the speed of the new scene replaces the previous time heat map to list the statistics, there is an Export button to export the data in an excel file. 120
  • Hikvision DS-2CD2232-I5 | User Manual - Page 122
    User Manual of Network Camera Figure 6-79 Space Heat Map Notes:  As shown in the figure above, red color block (255, 0, 0) indicates the most welcome area, and
  • Hikvision DS-2CD2232-I5 | User Manual - Page 123
    User Manual of Network Camera Figure 6-80 People Counting Configuration 3. Check the of the detection line to adjust its length. 4) To delete the detection line, click the Delete Line button. Note: The detection line should cover the whole entrance / exit. 6. An arrow indicating the entering
  • Hikvision DS-2CD2232-I5 | User Manual - Page 124
    User Manual of Network Camera 2) Select the detection line, and a set of blue lines lines to adjust the distance between them as the majority length of the blue marking lines. 8. Click the Reset Counter button, and the number of the people entered and exited will be cleared to zero. 9. Click Edit to
  • Hikvision DS-2CD2232-I5 | User Manual - Page 125
    User Manual of Network Camera 5. Click Counting to calculate the data. 6. Select to export the Statistics Result as Table, Bar Chart, or Line Chart. Note: If you select table to list the statistics, there is an Export button to export the data in an excel file. Figure 6-81 Statistics Result Note: It
  • Hikvision DS-2CD2232-I5 | User Manual - Page 126
    User Manual of Network Camera Chapter 7 Storage Settings Before you start: To Network Disk (2) Enter the IP address of the network disk, and enter the file path. (3) Select the mounting type. NFS and SMB/CIFS are selectable. And you can set the user name and password to guarantee the security if
  • Hikvision DS-2CD2232-I5 | User Manual - Page 127
    Camera Notes:  Please refer to the User Manual of NAS for creating the file path. For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing
  • Hikvision DS-2CD2232-I5 | User Manual - Page 128
    recording, refer to Section 5.3 Recording and Capturing Pictures Manually. In this section, you can follow the instructions to configure the scheduled recording. By default, the record files of scheduled recording are stored in the SD card (if supported) or in the network disk. Steps: 1. Enter the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 129
    User Manual of Network Camera Figure 7-5 Recording Schedule Interface 2. Check the checkbox of Enable Record Schedule to enable scheduled recording. 3. Set the record parameters of the camera.
  • Hikvision DS-2CD2232-I5 | User Manual - Page 130
    User Manual of Network Camera or 10 min. Note: The record parameter configurations vary depending on the camera model. 4. Click Edit to edit the record schedule. Figure 7-7
  • Hikvision DS-2CD2232-I5 | User Manual - Page 131
    User Manual of Network Camera  Record Triggered by Motion Detection If you select Motion Detection, the video will be recorded when the motion is detected. Besides configuring
  • Hikvision DS-2CD2232-I5 | User Manual - Page 132
    User Manual of Network Camera Figure 7-8 Edit Record Schedule (3) Check the checkbox of snapshot and event-triggered snapshot. The captured picture can be stored in the SD card (if supported) or the netHDD (For detailed information about netHDD, please refer to Section 7.1 Configuring NAS Settings
  • Hikvision DS-2CD2232-I5 | User Manual - Page 133
    Manual of Network Camera Check the Enable Event-triggered Snapshot checkbox to check event-triggered snapshot. 3. Select the quality of the snapshot. 4. Set the time interval between two snapshots. 5. Click Save to save the settings. Uploading to FTP You can follow below configuration instructions
  • Hikvision DS-2CD2232-I5 | User Manual - Page 134
    User Manual of Network Camera Figure 7-9 Snapshot Settings 7.4 Configuring Lite Storage Purpose: When there is no moving object in the monitoring scenario, the frame rate and bitrate of the video stream can be reduced to lengthen the storage time of the SD card. Note: Lite storage function varies
  • Hikvision DS-2CD2232-I5 | User Manual - Page 135
    to the User Manual of NVR for details. Steps: 1. Enter the Cloud Storage interface: Configuration > Advanced Configuration > Storage > Cloud Storage. 2. Check the checkbox of Enable Cloud Storage. 3. Input the IP address and port of the storage server. 4. Input the user name, password and confirm
  • Hikvision DS-2CD2232-I5 | User Manual - Page 136
    User Manual of Network Camera Figure 7-11 Cloud Storage Settings 135
  • Hikvision DS-2CD2232-I5 | User Manual - Page 137
    User Manual of Network Camera Chapter 8 People Counting Note: Compared with the people counting function supported by the iDS camera, the people counting of the non-iDS do not need to configure the calibrations, and the parameter configuration is easier. Steps： 
  • Hikvision DS-2CD2232-I5 | User Manual - Page 138
    User Manual of Network Camera 6. Click head or shoulder as a target. It is recommended you set the sensitivity as the default value, which is 50. 8. Configure the mounting related parameters. Camera Viewing Angle: Refers statistics, there is an Export button to export the data in an excel file. 137
  • Hikvision DS-2CD2232-I5 | User Manual - Page 139
    User Manual of Network Camera Figure 8-2 Statistics Result 138
  • Hikvision DS-2CD2232-I5 | User Manual - Page 140
    User Manual of Network Camera Chapter 9 Road Traffic Purpose: Vehicle Detection and Mixed-traffic Detection are available for the road traffic monitoring. In Vehicle Detection, the passed
  • Hikvision DS-2CD2232-I5 | User Manual - Page 141
    User Manual of Network Camera 1) To edit the arming schedule, click Edit button. 2) Choose the day you want to set the arming schedule. 3) Click to set the time period for the arming schedule. 4) (Optional) After you set the arming schedule, you can click the Copy button to copy the schedule to
  • Hikvision DS-2CD2232-I5 | User Manual - Page 142
    User Manual of Network Camera  Configuring the Upload Picture 1. Set the picture vehicle color, etc. You can also click the up and down direction buttons to adjust the sequence of the text. 4. Click the Save button to activate the settings. Figure 9-2 Upload Picture Settings  Configuring the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 143
    User Manual of Network Camera Figure 9-3 Overlay Content Settings 142
  • Hikvision DS-2CD2232-I5 | User Manual - Page 144
    User Manual of Network Camera Chapter 10 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD
  • Hikvision DS-2CD2232-I5 | User Manual - Page 145
    User Manual of Network Camera Button Figure 10-3 Playback Toolbar Table 10-1 Description of the buttons Operation Button Operation Play Capture a picture Pause Start/Stop clipping video / files Stop / Audio on and adjust volume/Mute Speed down Speed up Playback by frame /
  • Hikvision DS-2CD2232-I5 | User Manual - Page 146
    User Manual of Network Camera Chapter 11 Log Searching Purpose: The operation, alarm, exception and information of the camera can be stored in log files. You can
  • Hikvision DS-2CD2232-I5 | User Manual - Page 147
    Security > User Or Configuration > Advanced Configuration> Security > User Figure 12-1 User Information  Change the Admin Password Note: YOU MUST CHANGE THE DEFAULT PASSWORD - The default Admin account password (12345) is for first-time log-in purposes only. Steps: 1. Select the admin user from the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 148
    User Manual of Network Camera  The admin user cannot be deleted and you can only change the admin password. Figure 12-2 Change the Admin Password  Add a User Steps: 1. Click Add to add a user. 2. Input the User Name, select Level and input Password. Notes: ● Up to 31 user accounts can be created.
  • Hikvision DS-2CD2232-I5 | User Manual - Page 149
    User Manual of Network Camera 4. Click OK to finish the user addition. Figure 12-3 Add a User  Modify a User Steps: 1. Left-click to select the user from the list and click Modify. 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can
  • Hikvision DS-2CD2232-I5 | User Manual - Page 150
    Manual of Network Camera For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices. The password Authentication Purpose: You can specifically secure the stream data of live view. Steps: 1. Enter
  • Hikvision DS-2CD2232-I5 | User Manual - Page 151
    disable the RTSP authentication. Note: If you disable the RTSP authentication, anyone can access the video stream by the RTSP protocol via the IP address. 3. this function allows visit for whom doesn't have the user name and password of the device. Note: Only live view is available for the anonymous
  • Hikvision DS-2CD2232-I5 | User Manual - Page 152
    User Manual of Network Camera There will be a checkbox of Anonymous by the next time you logging in , video surveillance is inappropriate in areas where people have a higher expectation of privacy. 12.4 IP Address Filter Purpose: This function makes it possible for access control. Steps: 1. Enter the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 153
    User Manual of Network Camera Figure 12-8 IP Address Filter Interface 2. Check the checkbox of Enable IP Address Filter. 3. Select the type of IP Address Filter in the drop-down list, Forbidden and Allowed are selectable. 4. Set the IP Address Filter list.  Add an IP Address Steps: (1) Click the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 154
    Manual of Network Camera Figure 12-10 Modify an IP (3) Click the OK to finish modifying.  Delete an IP Address Left-click an IP address from filter list and click Delete.  Delete all IP Addresses Click Clear to delete all the IP addrsses. 5. Click Save to save the settings. 12.5 Security Service
  • Hikvision DS-2CD2232-I5 | User Manual - Page 155
    User Manual of Network Camera 12.6 Viewing Device Information Enter the Device Information interface: Configuration the Device Name. Other information of the network camera, such as Model, Serial No., Firmware Version, Encoding Version, Number of Channels, Number of HDDs, Number of Alarm Input and
  • Hikvision DS-2CD2232-I5 | User Manual - Page 156
    > Advanced Configuration> System > Maintenance 2. Click Restore or Default to restore the default settings. Figure 12-14 Restore Default Settings Note: After restoring the default settings, the IP address is also restored to the default IP address, please be careful for this action. 12.7.3 Exporting
  • Hikvision DS-2CD2232-I5 | User Manual - Page 157
    User Manual of Network Camera 4. Click Export and set the saving path to save Advanced Configuration> System > Maintenance 2. Select firmware or firmware directory to locate the upgrade file. Firmware: Locate the exact path of the upgrade file. Firmware Directory: Only the directory the upgrade file
  • Hikvision DS-2CD2232-I5 | User Manual - Page 158
    User Manual of Network Camera port. Device parameters can be configured by using software such as HyperTerminal. The serial port parameters must be the same as the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 159
    Protocol and PTZ Address parameters should be exactly the same as the PTZ camera parameters. 12.10 Service Settings Go to Configuration> Advanced Configuration> System > Service to enter the service settings interface. Service settings refer to the hardware service the camera supports, and it varies
  • Hikvision DS-2CD2232-I5 | User Manual - Page 160
    the searched devices in the Online Devices interface. Device information including the device type, IP address, port number, gateway, etc. will be displayed. Figure A.1.1 Search Online Devices went offline.  Search online devices manually You can also click Refresh to refresh the online device list
  • Hikvision DS-2CD2232-I5 | User Manual - Page 161
    User Manual of Network Camera searched devices will be added to the list. Note: the right side. 2. Edit the modifiable network parameters, e.g. IP address and port number. 3. Enter the password of the admin account of the device in the Password field and click Save to save the changes. For your
  • Hikvision DS-2CD2232-I5 | User Manual - Page 162
    User Manual of Network Camera  Restore default password Note: Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. You have the responsibility to keep you password properly. Steps: 1. Contact our technical engineers to get the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 163
    User Manual of Network Camera Appendix 2 Port Mapping The following settings are as in the following figure, including IP address and subnet mask settings. Figure A.2.2 Set the LAN parameters 3. Set the port mapping in the virtual severs of Forwarding. By default, camera uses port 80, 8000 and
  • Hikvision DS-2CD2232-I5 | User Manual - Page 164
    User Manual of Network Camera another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings mentioned above, map the port 80, 8000, 554 and 8200 for the
  • Hikvision DS-2CD2232-I5 | User Manual - Page 165
    User Manual of Network Camera 164
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
User Manual of Network Camera
0
User Manual
UD.6L0201D1673A01
Network Camera