HP V142 HP V142 Rack User Guide

HP V142 Manual

Get HP V142 PDF manuals and user guides View all HP V142 manuals
Add to My Manuals
Save this manual to your list of manuals

HP V142 manual content summary:

  • HP V142 | HP V142 Rack User Guide - Page 1
    HP V142 Rack User Guide Part Number 597608-002 June 2010 (Second Edition)
  • HP V142 | HP V142 Rack User Guide - Page 2
    such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Intended audience This document is for the person who installs racks and rack products. This procedure
  • HP V142 | HP V142 Rack User Guide - Page 3
    stabilizer option kit ...11 Rack baying option kit ...12 Installing components ...13 Installing rack components ...13 Rack options ...14 Ordering rack options ...14 Specifications ...15 HP V142 Rack specifications ...15 Electrostatic discharge ...16 Preventing electrostatic discharge ...16 Grounding
  • HP V142 | HP V142 Rack User Guide - Page 4
    the Best Practices document on the HP website (http://h18004.www1.hp.com/products/servers/proliantstorage/racks). Space requirements When deciding where to place your rack: • At least 1219 mm (48 in) of clearance is needed all the way around the pallet and above the rack to enable the removal of the
  • HP V142 | HP V142 Rack User Guide - Page 5
    , refer to the Important Safety Instructions that are shipped with the rack. Also, refer to the Safety and Comfort Guide-Precautions for Server and Network Products on the HP website (http://www.hp.com) (search for Safety and Comfort Guide). Additional rack considerations Consider the following
  • HP V142 | HP V142 Rack User Guide - Page 6
    one less than the number of racks in the suite. Each baying kit supplies parts to bay two cabinets on 600 mm (24 in) center line spacing. • Side panels-Only one set of side panels is required for each row of bayed racks. • Stabilizer kit-A stabilizer kit is either required or recommended, depending
  • HP V142 | HP V142 Rack User Guide - Page 7
    . • Load the heavier components first from the bottom of the rack. • Be sure to balance the weight load among bayed racks. For example, if you have several UPS units and several servers, do not load all of the UPS units into one rack. Instead, distribute them evenly in the bottom positions of each
  • HP V142 | HP V142 Rack User Guide - Page 8
    to be installed For comfort and efficiency while setting up your rack, use power tools where applicable. Removing the rack doors To provide access to all sides of the rack while you are installing the various components, remove the rack doors. Removing the front door 1. Unlock the door, and open it
  • HP V142 | HP V142 Rack User Guide - Page 9
    hinge pin down, and tilt the door away from the rack. 3. Lift the door up to remove it from the bottom hinge. Store the door in an upright position, taking care to protect it from damage. Removing the rear door 1. Unlock the door and open it. Preparing the rack for component installation 9
  • HP V142 | HP V142 Rack User Guide - Page 10
    2. Open the hinge bracket by pulling down on the top hinge pin. 3. Lift the rear door off the hinge bracket and remove it from the rack. Store the doors in an upright position, taking care to protect them from damage. Preparing the rack for component installation 10
  • HP V142 | HP V142 Rack User Guide - Page 11
    row. • Position and install the baying option kit before populating the racks with components. • Ensure that the weight of the rack rests on the leveling feet. Rack stabilizer option kit The HP V142 Rack Stabilizer Option Kit provides stability and support, preventing possible tipping when equipment
  • HP V142 | HP V142 Rack User Guide - Page 12
    bay racks together by installing the HP V142 Rack Baying Option Kit, as long as the racks are the same series, height, and depth. This configuration helps decrease space needs and increase stability. For more information, see the HP V142 Baying Rack Option Kit Installation Instructions. Stabilizing
  • HP V142 | HP V142 Rack User Guide - Page 13
    are for standard installations. For specific installation instructions, refer to the documentation included with your component. The following steps outline the sequence for installing rack-mountable components in a rack. HP strongly recommends installing a stabilizer foot before any other component
  • HP V142 | HP V142 Rack User Guide - Page 14
    contact your nearest HP authorized reseller. Rack option HP V142 Rack Side panel rack option kit HP V142 Rack Stabilizer rack option kit HP V142 Rack Ground bonding rack option kit HP V142 Rack Baying rack option kit Description Encloses the sides of a rack Increases the stability of free-standing
  • HP V142 | HP V142 Rack User Guide - Page 15
    Specifications HP V142 Rack specifications Item U height Width Depth Static load Specification 42U 600 mm (23.62 in) 1,070 mm (42.13 in) 907.2 kg (2,000 lb) Specifications 15
  • HP V142 | HP V142 Rack User Guide - Page 16
    up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other service tools. • Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding
  • HP V142 | HP V142 Rack User Guide - Page 17
    /us/en/wwcontact.html). For HP technical support: • In the United States, for contact options see the Contact HP United States webpage (http://welcome.hp.com/country/us/en/contact_us.html). To contact HP by phone: o Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day
  • HP V142 | HP V142 Rack User Guide - Page 18
    Acronyms and abbreviations CPU central processing unit CRT cathode-ray tube KVM keyboard, video, and mouse PDU power distribution unit RKM rackmount keyboard monitor TMRA recommended ambient operating temperature UPS uninterruptible power system Acronyms and abbreviations 18
  • HP V142 | HP V142 Rack User Guide - Page 19
    guidelines 6 grounding methods 16 I installing components 13 installing rack components 13 N notices 2 O optimum environment 4 ordering options 14 P preparing the rack for component installation 8 R rack baying option kit 12 rack doors, removing 8, 9 rack options 14 rack stabilizer option kit 11
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
HP V142 Rack
User Guide
Part Number 597608-002
June 2010 (Second Edition)