HP Latex 360 Site preparation guide Latex 3x5
HP Latex 360 Manual
 |
View all HP Latex 360 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Latex 360 manual content summary:
- HP Latex 360 | Site preparation guide Latex 3x5 - Page 1
HP Latex 300 Printer Series Site Preparation Guide - HP Latex 360 | Site preparation guide Latex 3x5 - Page 2
to change without notice. The only warranties for HP products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP Latex 360 | Site preparation guide Latex 3x5 - Page 3
Table of contents 1 Overview ...1 Introduction ...1 Documentation ...1 Customer responsibility ...1 Installation time schedule ...2 2 Site preparation requirements ...3 Physical space requirements ...3 Unloading route ...3 Environmental specifications ...4 Ventilation ...4 Air conditioning ...4 - HP Latex 360 | Site preparation guide Latex 3x5 - Page 4
iv ENWW - HP Latex 360 | Site preparation guide Latex 3x5 - Page 5
your printer, and can also be downloaded from http://www.hp.com/go/ Latex300/manuals/: ● Introductory information ● Limited warranty ● Legal information ● Site preparation guide (this guide) ● Assembly instructions ● User's guide Customer responsibility You are responsible for preparing the physical - HP Latex 360 | Site preparation guide Latex 3x5 - Page 6
Installation time schedule Allow a minimum of three hours for the installation. The installer may require the help of three people to perform certain tasks during installation. 2 Chapter 1 Overview ENWW - HP Latex 360 | Site preparation guide Latex 3x5 - Page 7
2 Site preparation requirements Physical space requirements Unloading route The route between the unloading area of the printer and the installation site, including any corridors and doorways through which the printer must be transported, is important to proper site preparation and must be - HP Latex 360 | Site preparation guide Latex 3x5 - Page 8
so may cause print-quality problems or damage sensitive electronic components. the printer parts and cartridges and can result in ink leaks and printer errors. In this case, HP recommends that HP Latex 315 Printers ● 2.6 kW (8.9 kBTU/h) for HP Latex 335 Printer ● 4.6 kW (15.7 kBTU/h) for HP Latex - HP Latex 360 | Site preparation guide Latex 3x5 - Page 9
Print ● Replace a substrate roll ● Service the printer or replace printer components ● ll be using for the RIP station. See http://www.hp.com/go/latexrips for a complete list of certified RIP following tasks: NOTE: In order to perform remote support, the printer must have access to the Internet using - HP Latex 360 | Site preparation guide Latex 3x5 - Page 10
. If you can connect to hp.com, you can check the settings in the main window, or in the HTTP part of the Advanced settings window. ● For Safari, printhead alignment during printer setup. Return the site preparation checklist The checklist must be completed and returned to your reseller or service - HP Latex 360 | Site preparation guide Latex 3x5 - Page 11
the equipment is installed. The printer requires two power cords that meet the following requirements. Dedicated lines per SKU HP Latex 365/375 HP Latex 335 HP Latex 315 Printer Curing Printer Curing Printer Curing Dedicated line Yes Yes Not required. Do Yes Not required. Do Not - HP Latex 360 | Site preparation guide Latex 3x5 - Page 12
and check the plug type. WARNING! Use only use the power cord supplied by HP with the printer. Do not use a power strip (relocatable power tap) to HP-approved power cord. NOTE: You need two power cords from the tables below. HP Latex 335/365/375 Printers-Power cord specifications Country HP part - HP Latex 360 | Site preparation guide Latex 3x5 - Page 13
NEMA 6-20P, 240 V, 20 A, non-locking International 8121-1287 2.5 m IEC 60309, 240 V, 16 A, 2L +PE HP Latex 315 Printer-Power cord specifications per region Country HP part number Length Plug type Plug America Region Argentina 8121-0925 2.5 m IRAM 2073 Brazil Chile, Uruguay 8121-1101 - HP Latex 360 | Site preparation guide Latex 3x5 - Page 14
HP Latex 315 Printer-Power cord specifications per region (continued) Country HP part number Length Plug type Plug Korea, Indonesia 8120-6352 2.5 m CEE 7-VII India 8121-1074 2.5 m IS 1293 Taiwan 8121-1033 4.5 m CNS 690 Hong Kong, Singapore 8121- - HP Latex 360 | Site preparation guide Latex 3x5 - Page 15
HP Latex 315 Printer-Power cord specifications per region (continued) Country HP part number Length Plug type Plug U.K. 8121-0907 2.5 m BS 1363/A (13A fused) Middle East 8120-6360 2.5 m NEMA 6-20P, 240 V, 20 A, non-locking Appliance coupler (printer connection) - HP Latex 360 | Site preparation guide Latex 3x5 - Page 16
aware of all requirements and specifications highlighted in this guide? (Required) Is the single-phase line voltage inside receptacles (wall sockets) suitable for the power cord plug type provided by HP? (Required) Are the wall receptacles (wall sockets) and electrical installation suitable - HP Latex 360 | Site preparation guide Latex 3x5 - Page 17
for supplies such as substrate and ink cartridges to be available on the day of installation? Have you met the requirements specified in this guide? No (Required) Comments Date of site preparation completion Site preparation guide edition number or copyright date Customer signature ENWW 13
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
 |
 |
HP Latex 300 Printer Series
Site Preparation Guide