HP 158222-B21 Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install
HP 158222-B21 - StorageWorks Fibre Channel SAN Switch 8 Manual
UPC - 720591237431
View all HP 158222-B21 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 158222-B21 manual content summary:
- HP 158222-B21 | Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install - Page 1
the contents of the universal mounting kit and provides procedures for mounting Fibre Channel 8-port (380591-B21/ DS-DSGGA-AA or 176219-B21/ DS-DSGGC-AA) and 16-port (380578-B21/ DS-DSGGA-AB or 212776-B21/DS-DSGGC-AB) switches into the following Compaq racks: • RETMA 41U or 42U • Compaq Classic - HP 158222-B21 | Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install - Page 2
Installation Process Orientation The current or planned configuration of rack components determines which installation process orientation to follow. A key consideration is whether the cables are routed at the front or rear of the rack. General rack configuration guidelines include: • For RETMA 41U - HP 158222-B21 | Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install - Page 3
Attaching the Mounting Brackets Attach two mounting brackets, using the appropriate procedure for the rack type. WARNING: To reduce the risk of personal injury or equipment damage during installation, never extend multiple components installed in the rack at the same time. A rack may become unstable - HP 158222-B21 | Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install - Page 4
and that flat washers are used. Installing screws longer than 9/32 inch or without a flat washer may damage the switch. • For older 8-port switches (380591-B21/ DS-DSGGA-AA) in rack-front and rear installations, see Figure 8. Use four pan head SEMS screws (10-32 x 9/32 inches) and four flat washers - HP 158222-B21 | Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install - Page 5
• For 1.5U 16-port switches (such as 212776-B21/ DS-DSGGC-AB)-Positioned approximately three inches from the rack front for cable-front installations (see Figures 11 and 12), or one inch from the - HP 158222-B21 | Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install - Page 6
• For 2U 16-port switches (such as 380578-B21/ DS-DSGGA-AB) in rack-front and rack-rear installations, see Figures 15 and 16. Use four pan head SEMS screws (10-32 x 9/32 inches) - HP 158222-B21 | Fibre Channel Switch, 8-/16-Port Universal Mounting Kit Install - Page 7
Routing Power and Data Cables IMPORTANT: All switches use the same cable routing method, so a representative example is used here to illustrate this process. Install a snap-on cable tie into each slide bracket, as shown in Figure 19 (representative example), as desired, and route the power cables
Compaq StorageWorks
Fibre Channel
Switch, 8-/16-Port
Universal
Mounting Kit
Open Card Completely Before
Beginning Installation Procedures
© 2001 Compaq Information Technologies Group, L.P.
Compaq, the Compaq logo, and StorageWorks are trademarks of Compaq
Information Technologies Group, L.P.
All other product names mentioned herein may be trademarks of their
respective companies.
Compaq shall not be liable for technical or editorial errors or omissions
contained herein. The information is provided “as is” without warranty of
any kind and is subject to change without notice. The warranties for
Compaq products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as
constituting an additional warranty.
Printed in the U.S.A.
Fibre Channel Switch, 8-/16-Port Universal Mounting Kit
Third Edition (November 2001)
Part Number: EK-GGAAB-IA. C01
Compaq Computer Corporation
About This Card
This card identifies the contents of the universal mounting kit
and provides procedures for mounting Fibre Channel 8-port
(380591–B21/ DS–DSGGA–AA or 176219–B21/
DS–DSGGC–AA) and 16-port (380578–B21/
DS–DSGGA–AB or 212776–B21/DS–DSGGC–AB) switches
into the following Compaq racks:
•
RETMA 41U or 42U
•
Compaq Classic
•
Metric SW600
Kit Contents
NOTE:
This kit contains parts for multiple rack installations. Not all kit parts
are needed for all rack installations.
1
Mounting brackets (2)
2
Extender brackets (2)
3
Slide brackets (2)
4
Bag of miscellaneous hardware:
•
Snap-on cable ties (2)
•
Clip nuts (4)
•
Alignment washers (8)
•
Pan head SEMS screws, 10-32 x 9/32 inches (4)
•
Pan head SEMS screws, 10-32 x 5/8 inches (16)
•
Flat washers for #10 screws (4)
•
Pan head SEMS screws, 8-32 x 1/4 inches (4)
•
Flat washers for #8 screws (4)
Tools Required
•
No. 2 Phillips screwdriver
1
2
3
4
CXO7467B