Hayward VL Series Sand Filter Systems Model: VL40T32
Hayward VL Series Sand Filter Systems Manual
 |
View all Hayward VL Series Sand Filter Systems manuals
Add to My Manuals
Save this manual to your list of manuals |
Hayward VL Series Sand Filter Systems manual content summary:
- Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 1
OWNER'S MANUAL INSTALLATION, OPERATION & PARTS ISVL40 Rev. D SAND FILTER Model VL40T32 Basic safety precautions should always be followed, including the following: Failure to follow instructions can cause severe injury and/or death. This is the safety-alert symbol. When you see this symbol on your - Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 2
. Before starting system pump, all system valves must be set in a position to allow system water to return back to the pool. Do not change filter control valve position while system pump is running. Page 2 of 8 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS TOP MOUNT VALVE SAND FILTERS ISVL40 Rev D - Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 3
system should be installed, 1 1/2 feet below pool water level, on a level concrete slab, very firm ground, or equivalent, as recommended by your pool dealer. Position the filter so that the piping connections, control valve are accessible for operation, service and winterizing. 2. Assemble pump - Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 4
the expressed authorization of Hayward Pool Products, Inc. PLEASE REALIZE. Pure, clear swimming pool water is a combination of two factors- adequate filtration and proper water chemistry balance. One without the other will not give the clean water you desire. Your filter system is designed for - Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 5
O-ring Strainer Housing kit including: 1 Strainer Housing, drain plug o-ring and plug, and pump interlocking nut Pump Shaft Seal and pump Body 1 O-Ring (Not shown) Pump without Strainer 1 Page 5 of 8 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS TOP MOUNT VALVE SAND FILTERS ISVL40 Rev D - Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 6
. PROBLEM SOLVING LIST LOW WATER FLOW REMEDY 1. Check skimmer and pump strainer baskets for debris. 2. Check for restrictions in intake and discharge lines. 3. Check for air leak in intake line (indicated by bubbles returning to pool). 4. Backwash filter. SHORT FILTER CYCLES POOL WATER WON - Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 7
Page 7 of 8 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS TOP MOUNT VALVE SAND FILTERS ISVL40 Rev D - Hayward VL Series Sand Filter Systems | Model: VL40T32 - Page 8
□ Soft Sided □ Chlorinator □ Skimmer □ Heater □ Heat Pump □ Salt/Chlorine Generator □ Controls Size of Pool REGISTER ONLINE AT WWW.HAYWARDNET.COM © Hayward Pool Products, Inc. 2010 All rights Page 8 of 8 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS TOP MOUNT VALVE SAND FILTERS ISVL40 Rev D
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
OWNER’S MANUAL
INSTALLATION, OPERATION & PARTS
SAND FILTER
Model VL40T32
SAVE THIS INSTRUCTION MANUAL
Basic safety precautions should always be followed, including the following: Failure to follow instructions can cause
severe injury and/or death.
This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for one of the
following signal words and be alert to the potential for personal injury.
WARNING
warns about hazards that
could
cause serious personal injury, death or major property damage
and if ignored presents a potential hazard.
CAUTION
warns about hazards that
will
or
can
cause minor or moderate personal injury and/or property
damage and if ignored presents a potential hazard.
It can also make consumers aware of actions that are unpredictable
and unsafe.
The
NOTICE
label indicates special instructions that are important but not related to hazards.
Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm)
ISVL40
Rev. D
Hayward Pool Products
One Hayward Industrial Drive, Clemmons, NC 27012
www.haywardnet.com