Harbor Freight Tools 40315 User Manual
Harbor Freight Tools 40315 - 7 in. Portable Wet Cutting Tile Saw Manual
 |
View all Harbor Freight Tools 40315 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 40315 manual content summary:
- Harbor Freight Tools 40315 | User Manual - Page 1
Model 40315 SET UP AND OPERATING INSTRUCTIONS Please Note: Diamond Blade not included, sold separately. Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Copyright© 2008 by Harbor Freight - Harbor Freight Tools 40315 | User Manual - Page 2
. General Power Tool Safety Warnings IMPORTANT SAFETY INFORMATION In this manual, on the labeling, and all other information provided with this instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions - Harbor Freight Tools 40315 | User Manual - Page 3
plugs with grounded power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b.Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. c. Do not expose power - Harbor Freight Tools 40315 | User Manual - Page 4
persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are in a hazardous situation. 5. Service a.Have your power tool serviced by a qualified repair person using have regular medical checkups to ensure medical problems are not being caused or worsened from - Harbor Freight Tools 40315 | User Manual - Page 5
vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. 8. a flat, level, sturdy surface capable of supporting the weight of the Saw and work pieces. it was not intended. and/or reduce its service life. 3. Be sure the product is properly - Harbor Freight Tools 40315 | User Manual - Page 6
POWER CORD TILE SAW 19. Never leave the Tile Saw unattended when it is plugged into an elec- trical outlet. Turn off the Tile Saw, and unplug it from its electrical outlet. 120 VOLT, GROUNDED ELECTRICAL OUTLET DRIP LOOP Figure 1 14. Always arrange a "drip loop" in the Power Cord/Plug (34) - Harbor Freight Tools 40315 | User Manual - Page 7
large work piece make sure its entire length is properly supported. If necessary, use a roller stand (not included) with Cutting Guide (57). 34. Never cut pieces too small to be held securely against the Cutting Guide without cautions discussed in this manual can- not cover all possible conditions and SKU - Harbor Freight Tools 40315 | User Manual - Page 8
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in operation for which it can be used. c. Disconnect saw before servicing, when changing cutting wheel or cleaning. ment. Depending on - Harbor Freight Tools 40315 | User Manual - Page 9
interference or pacemaker failure. In addition, peo- 17. The warnings, precautions, and ple with pacemakers should: instructions discussed in this in- • Avoid operating alone. struction manual cannot cover all • Do not use with power switch locked possible conditions and situations on. that - Harbor Freight Tools 40315 | User Manual - Page 10
the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounded Tools: Tools with Three Prong Plugs - Harbor Freight Tools 40315 | User Manual - Page 11
25' 50' 75' 100' 150' 2. Double insulated tools may be used extension cord or have it repaired by in either of the 120 volt outlets shown a qualified electrician before using it. in the preceding illustration. (See Outlets for 2-Prong Plug.) 7. Protect the extension cords from sharp objects, - Harbor Freight Tools 40315 | User Manual - Page 12
shown on the cover of this manual as soon as possible. INSTRUCTIONS FOR PUTTING INTO USE Read the ENTIRE IMPORTANT SAFETY INFORMATION section the Tile Saw will be temporarily or permanently used is flat, level, sturdy enough to support the weight of the Tile Saw, any workpieces, and any additional tools, and is - Harbor Freight Tools 40315 | User Manual - Page 13
) behind the edge of the Table. Attach the Star Knob to the Cutting Guide. (See Figure 2, below.). Install The Cutting Wheel Blade: 1. Make certain power while you tighten the Nut (4) securely with the Nut Driver (60). CUTTING GUIDE (57) CLAMPING PLATE (56) FIGURE 2 EDGE OF TABLE (51) STAR KNOB - Harbor Freight Tools 40315 | User Manual - Page 14
INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual . 1. Use Clamping Plate (56) to secure and support smaller work pieces to the built-in fence. Holding 's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly - Harbor Freight Tools 40315 | User Manual - Page 15
Operating Instructions 1. Fill Tray (17) with water and carefully slide Tray under Blade. Make sure water level is deep enough to cover lower edge of Cutting Wheel Blade, but not so deep as to spill over edge of Tray. (See Figure 3, below.) 2. Loosen Star Knob (20) and adjust the Cutting Guide (57 - Harbor Freight Tools 40315 | User Manual - Page 16
servicing a tool, use only identical replacement parts. Fol- TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool to its "OFF" position and low instructions in the "Inspection, Maintenance, And Cleaning" section of this manual , have the problem corrected before - Harbor Freight Tools 40315 | User Manual - Page 17
location out of reach of children and other unauthorized people. 10. CAUTION! All maintenance, service, or repairs not listed in this manual are only to be attempted by a qualified service technician.. Troubleshooting Problem Possible Causes 1. No power at outlet. Tool will not start 2. Cord not - Harbor Freight Tools 40315 | User Manual - Page 18
49 Blade Guard 50 Safety Label 51 Table 52 Ruler 53 Star Knob (M6) 54 Washer (M6) 55 Bolt (M6x16) 56 Clamping Plate 57 Cutting Guide 58 Rear Blade Cover 59 Spanner Wrench 60 Nut Driver SKU 40315 For technical questions, please call 1-800-444-3353. Page 18 - Harbor Freight Tools 40315 | User Manual - Page 19
ASSEMBLY DIAGRAM 18 Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 40315 For technical - Harbor Freight Tools 40315 | User Manual - Page 20
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
7" PORTABLE WET CUTTING
TILE SAW
Model
40315
SET UP AND OPERATING INSTRUCTIONS
Please Note: Diamond Blade not included, sold separately.
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
2008 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due
to continuing improvements, actual product may differ slightly from the product described herein.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10e