GE DCVH680GJMR Installation Instructions

Step 1

Verify Your Gas Installation (see section 2).

Step 2

Prepare the Area and Exhaust for Installation of New

Dryer (see section 1).

Step 3

Check and Insure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Specifications. (see section 6).

Step 4

Remove the Foam Shipping Pads (see section 1).

Step 5

Move the Dryer to the Desired Location.

Step 6

Level Your Dryer (see section 8).

Step 7

Connect the Gas Supply (see section 3) and check for

leaks (see section 4).

Step 8

Connect the External Exhaust (see section 7).

Step 9

Connect the Power Supply (see section 5).

Step 10

Check the Operation of the Power Supply, Gas

Connections, and Venting.

Step 11

Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation see section 9.

For Bathroom or Bedroom Installation see section 10.

For Mobile or Manufactured Home see section 11.

D

E

S

I

G

N

C

E

R

T

I

F

I

E

D

If you have any questions, call 1-800-GECARES (US) or 1-800-561-3344 (Canada)

or

Visit our Web site at:

www.GEAppliances.com (US)

Installation

Instructions

Gas Dryer

10

PEDESTALS FOR DRYERS

(comes with individual installation instructions)

3 models available:

500A436P010

Pub# 31-16229

In the state of Massachusetts, installation must be performed by a qualified or

licensed contractor, plumber, or gasfitter qualified or licensed by the state.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IMPORTANT-

Save these

instructions for local inspector’s use.

•

IMPORTANT-

Observe

all governing codes and ordinances.

•

Note to Installer

- Be sure to leave these

instructions with the customer.

•

Note to Customer

- Keep these

instructions with your Use and Care Book

for future reference.

•

Before the old dryer is removed from

service or discarded, remove the dryer door.

•

Service information and the wiring diagram

are located in the control console.

•

D

o not allow children on or in the appliance.

Close supervision of children is necessary

when the appliance is used near children.

•

Install the dryer where the temperature is

above 50°F for satisfactory operation of

the dryer control system.

•

•

Inspect the dryer exhaust outlet and

straighten the outlet walls if they are bent.

MATERIALS YOU WILL NEED

LEVEL

8" PIPE WRENCH

EXHAUST HOOD

FLEXIBLE GAS LINE CONNECTOR

SOAP SOLUTION

FOR LEAK DETECTION

PIPE

COMPOUND

DUCT TAPE

GLOVES

SAFETY GLASSES

4" DIAM METAL ELBOW

10" ADJUSTABLE WRENCHES

(x2)

4" DUCT CLAMPS

OR

4" SPRING CLAMPS

(x2)

(x2)

TOOLS YOU WILL NEED

SLIP JOINT PLIERS

FLAT BLADE SCREWDRIVER

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

To reduce the risk of severe injury or death, follow all installation instructions.

•

Clothes dryer installation must be performed by a qualified installer.

•

Install the clothes dryer according to these instructions and in accordance with local codes. In

the absence of local codes, installation must comply with National Fuel Gas Code,

ANSIZ223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

•

This dryer must be exhausted to the outdoors.

This act requires the governor of California to publish a list of substances known to the state to

cause cancer, birth defects or other reproductive harm and requires businesses to warn

customers of potential exposure to such substances. Gas appliances can cause minor

exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde and

soot, caused primarily by the incomplete combustion of natural gas or LP fuels. Properly

adjusted dryers will minimize incomplete combustion. Exposure to these substances can be

minimized further by properly venting the dryer to the outdoors.

•

California Safe Drinking Water and Toxic Enforcement Act

•

Use only 4” rigid metal ducting for exhausting the clothes dryer to the outdoors.

•

Do not install or store this appliance in any location where it could be exposed to water and or

weather.

•

Save these instructions. (Installers: Be sure to leave these instructions with the customer).

•

DO NOT install a clothes dryer with flexible plastic ducting materials.

If flexible metal (semi-

rigid or foil-type) duct is installed, it must be UL-listed and installed in accordance with the

instructions found in "Connecting The Dryer To House Vent" on page 6 of this manual.

Flexible

ducting materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct dryer airflow and increase the risk of fire.

- RISK OF FIRE

WARNING

•

SBSD227F, SBSD137H

SBSD107H

GE DCVH680GJMR Installation Instructions

GE DCVH680GJMR Manual

GE DCVH680GJMR manual content summary: