Gateway KX2153 User Manual
Gateway KX2153 Manual
 |
View all Gateway KX2153 manuals
Add to My Manuals
Save this manual to your list of manuals |
Gateway KX2153 manual content summary:
- Gateway KX2153 | User Manual - Page 1
Gateway LCD Monitor User's Guide - Gateway KX2153 | User Manual - Page 2
Gateway LCD Monitor User's Guide Original Issue: 4 /2013 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual to your computer. All correspondence - Gateway KX2153 | User Manual - Page 3
LCD monitors The following are normal with the LCD monitor and do not indicate a problem instructions marked on the product. Cleaning your monitor Please carefully follow these guidelines when cleaning the monitor: • Always unplug the monitor sure both the LCD monitor and the computer are turned off - Gateway KX2153 | User Manual - Page 4
power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect your hearing, follow these instructions. • Gradually increase the volume until you can hear it clearly and comfortably and without distortion. • After setting the volume level, do not - Gateway KX2153 | User Manual - Page 5
type SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length. Product servicing Do not attempt to service this product change in performance, indicating a need for service • the product does not operate normally after following the operating instructions - Gateway KX2153 | User Manual - Page 6
and obey all signs and instructions. Potentially explosive atmospheres include areas . Switch off the device near gas pumps at service stations. Observe restrictions on the use of radio of small children. IT Equipment Recycling Information Gateway is strongly committed to environmental protection and - Gateway KX2153 | User Manual - Page 7
vii Disposal instructions Do not throw this electronic device into the trash when discarding. Equipment (WEEE) regulations, visit http://www.acer‐group.com/public/Sustainability/ LCD pixel statement The LCD unit is produced with high-precision manufacturing techniques. Nevertheless, some pixels may - Gateway KX2153 | User Manual - Page 8
within 15 minutes of user inactivity. • Activate computer's Sleep mode within 30 minutes of user inactivity. • Wake the computer from Sleep mode by for more comfortable computer use. Finding your comfort zone Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest - Gateway KX2153 | User Manual - Page 9
eyes frequently. • Give your eyes regular breaks by looking away from the monitor and focusing on a distant point. • Blink frequently to keep your eyes good work habits Develop the following work habits to make your computer use more relaxing and productive: • Take short breaks regularly and - Gateway KX2153 | User Manual - Page 10
undesired operation. The following local Manufacturer /Importer is responsible for this declaration: Product: Model Number: SKU Number: LCD Monitor KX2153 KX2153 xxxxxx ("x" = 0~9, a ~ z, A ~ Z or Blank) Name of Responsible Party: Acer America Corporation Address of Responsible Party: 333 West - Gateway KX2153 | User Manual - Page 11
for your safety and comfort Safety instructions Cleaning your monitor Connecting/disconnecting the device Accessibility Safe listening Warnings Using electrical power Product servicing Additional safety information IT equipment recycling information Disposal instructions LCD pixel statement Tips and - Gateway KX2153 | User Manual - Page 12
Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor Quick start guide Audio Cable (Option) D-sub cable (Option) DVI cable (Option) AC power cord EN-1 - Gateway KX2153 | User Manual - Page 13
screen. ① ② Remove: Reverse the steps to remove the base. Screen position adjustment To optimize the viewing position, you can adjust the monitor tilt by using both of your hands to hold the edges of the monitor as shown below. The monitor can be adjusted to 25 degrees up or 5 degrees down. EN-2 - Gateway KX2153 | User Manual - Page 14
user-adjustment is required. • Plug one end of the power cord to the AC inlet, and plug the other end into an AC outlet. • For units using 120 V AC: Use a UL-listed cord set, type SVT wire and plug rated your system supports the DDC protocol, the monitor is able to plug-and-play. - Gateway KX2153 | User Manual - Page 15
assignment 1 5 6 10 11 15 15-pin color display signal cable PIN No. Description 1 Red 2 Green 3 Blue 4 Monitor ground 5 DDC-return 6 R-ground 7 G-ground 8 B-ground PIN No. Description 9 +5 V 10 Logic ground 11 Monitor ground 12 DDC-serial data 13 H-sync 14 V-sync 15 DDC-serial clock EN-4 - Gateway KX2153 | User Manual - Page 16
NC 14 +5 V power 15 GND (return for +5 V hsync.vsync) 16 Hot-plug detection 17 TMDS data 0- 18 TMDS data 0+ 19 TMDS data 0/5 shield 20 NC 21 NC 22 TMDS clock shield 23 TMDS clock+ 24 DDC TMDS clock- EN-5 - Gateway KX2153 | User Manual - Page 17
Standard timing table 1 VGA 640×480 60 Hz 2 MAC 640×480 66.66 Hz 3 VESA 720×400 70 Hz 4 SVGA 800×600 56 Hz 5 SVGA 800×600 60 Hz 6 XGA 1024×768 60 Hz 7 XGA 1024×768 70 Hz 8 VESA 1152×864 75 Hz 9 SXGA 1280×1024 60 Hz 10 VESA 1280×720 60 Hz 11 WXGA - Gateway KX2153 | User Manual - Page 18
LCD monitor and the line-out port on the computer with the audio cable. 4 Turn on the monitor and computer Turn on the monitor first, then the computer. This sequence is very important. 5 If the monitor does not function properly, please refer to the troubleshooting section to diagnose the problem - Gateway KX2153 | User Manual - Page 19
USER CONTROLS Power Switch / Power LED: To turn the monitor ON or OFF. Lights up to indicate the power INPUT Input Key Use Input key to select from different video sources that may be connected to your monitor. (a) VGA input (b) DVI input As you cycle through the sources you will see the following - Gateway KX2153 | User Manual - Page 20
eColor Management Operation instructions Step 1: Press " " Key to open the eColor Management OSD and access the Features and Benefits Main Menu icon Sub Menu icon Sub Menu item Description N/A User mode User defined. Settings can be fine-tuned to suit any situation N/A ECO mode Adjusts - Gateway KX2153 | User Manual - Page 21
Adjusting the OSD settings Note: The following content is for general reference only. Actual product specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and - Gateway KX2153 | User Manual - Page 22
Adjusting the OSD position 1 Press the MENU key to bring up the OSD. 2 Using the directional keys, select OSD from the on screen display. Then navigate to the feature you wish to adjust. EN-11 - Gateway KX2153 | User Manual - Page 23
Adjusting the setting 1 Press the MENU key to bring up the OSD. 2 Using the / keys, select Setting from the OSD. Then navigate to the feature you wish to adjust. 3 The Setting menu can be used to adjust the screen Menu Language and other important settings. EN-12 - Gateway KX2153 | User Manual - Page 24
Product information Information 1920 x 1080 H:65KHz V:60Hz VGA Input S/N:ETL5309 1326350380B3742 1 Press the MENU key to bring up the OSD. 2 Using the / keys, select Information from the OSD. Then the basic information of LCD monitor will show up for current input. EN-13 - Gateway KX2153 | User Manual - Page 25
Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. VGA mode Problem No picture visible LED status White Off Remedy Using the OSD, adjust brightness and contrast to maximum or reset to their default - Gateway KX2153 | User Manual - Page 26
to their default settings. Check the power switch. Check if the AC power cord is properly connected to the monitor. Blinking White Check if the video signal cable is properly connected at the back of monitor. Check that the computer system is switched on and in power saving/ standby mode. EN-15
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
 |
 |
User's Guide
Gateway LCD Monitor