Ganz Security ZNT1-H Ganz G2 Fixed Thermal Quick Start Guide

CBC AMERICAS CORP. - EAST COAST +1 (919) 230-8700 | WEST COAST +1 (310) 222-8600 | MEXICO +52 (55) 5280 4660

ganzsecurity.com. 01/17

1

ZNT1-H Series Quick Start Guide

Before installing and operating the unit, please read this manual

thoroughly and keep it for future reference.

About the manuals

This manual provides the instructions for the quick installation

and the basic configuration of your IP device. For more detailed

information, refer to the camera

’

s installation guide and the web

page user

’

s manual.

Part names and functions

Please check the name and position of each part by

referring to the following image.

Sunshield:

It prevents the lens from getting the direct sunlight.

NTSC / PAL Button:

The button switches the video output mode between

NTSC and PAL. Pressing the button will maintain the current video output

mode unless pressing again to switch to the other mode.

Analogue Video Output:

Connect a video output cable to see video via an

analogue monitor.

RJ45 Socket:

RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)

Reset Button:

Press the button either for the restart or the factory default

of the device. For

restart

,

1.

press the button only for 2 seconds while the

device is powered on.

2.

Wait for the system to reboot. For

factory default

,

1.

press the button for 10 seconds while the device is powered on.

2.

Wait for

the system to reboot. There are also the methods performed on the

camera

’

s web page. Refer to the Reboot and Factory Default section in this

manual.

Terminal Connectors for DI/DO:

Connector for audio input (sensor) and

audio outputs (alarms). Refer to the Connection section for more

information about the characteristics of DIDO in the installation guide.

Terminal Connectors for Audio I/O:

Connector for audio input (MIC) and

audio output(speaker). Refer to the Connection section for more

information about the characteristics of audio in the installation guide.

Terminal Connectors for RS-485:

Connector for RS-485. Refer to the

Connection section for more information about the characteristics about RS-

485 in the installation guide.

Terminal Connector for power adaptor:

Connector for power supply

(12VDC, 24VAC, and PoE supported).

Installation

Installing Cable Gland

To meet the IP66 requirements, you need to install the cable gland unit to

the camera. Follow the instructions on the other side of this page.

Connecting Cable(s)

Refer to the connection section for more information about each connector.

Installing Base Mount

Connecting Cables

For the information about the necessary cables, refer to the part names and

functions section on the left side of this page and the Connection section in

the installation guide.

Closing Back Cover

Installing Sunshield

Terminal

connectors

for power

adaptor

Sunshield

1)

Detach the back cover by twisting it counter-clockwise.

2)

Disassemble the cable gland unit

(Disassembled parts: electrical nut, rubber sealing

ring inside the gland - you need to take it out, gland body, and sealing nut)

.

3)

Pass the electrical nut through the ends of the necessary cables.

4)

Pass the cables through the holes both on the back and the bottom of

the camera by referring to the image above.

5)

Pass the provided O-ring, gland body through the ends of the cables

that are on the backside of the camera.

6)

Insert the cables into the rubber sealing ring at the point where about

4.5 inches (11.5 cm) of the cable ends remains to connect to the

corresponding connectors on the back panel later.

7)

Push the rubber sealing ring through the claw of the gland body.

8)

Insert the sealing nut into the thread of the gland body, and tighten it

by turning the nut on the thread. The rubber sealing ring will be tightened

to fill the gap between the rubber sealing ring and the cables.

9)

Push the gland unit through the hole on the back of the camera so that

the other end of the thread on the gland unit will be inserted into hole for

gland.

10)

Fix the gland unit to the hole by inserting the electrical nut and

tightening it on the thread of the gland unit.

NOTE1

A thin type of the BNC cable is recommended when you insert

multiple cables including a BNC cable as the standard size of BNC cable is

too thick to be inserted together into the rubber sealing ring.

NOTE2

Use the detachable cable with a separate BNC connector to pass

the hole of the sealing nut or the female type head of the BNC cable to

pass the hole of the sealing nut.

1)

Insert the provided

8 tamper resistant

screws to the

corresponding screw

holes on the base

mount by referring to

the image on the right.

2)

Tighten them with

a Phillips head #2

screwdriver to fix the

base mount to the

camera.

1)

Insert the provided

silica gel packet inside

the back panel.

2)

Close the back

panel of the camera

by twisting the back

cover clockwise

on the camera

’

s back

panel.

3)

Insert the two tamper

resistant screws into the

holes on the back cover,

and tighten them with a

Phillips #2 screwdriver

to fix the back cover to

the camera unit.

* The model herein and its appearance are subject to change without any prior notice.

NTSC / PAL button

Analogue video output

RJ45 socket

Reset button

Terminal connectors

for DI/DO

Terminal connectors

for Audio In/Out

Terminal connectors

for RS-485

[ Back Panel of Camera ]

Electrical nut

Hole for gland O-ring

Gland body

Sealing nut

[Base Mount Installation: Upside-Down View]

Section	Page
ZNT1-H Series Quick Start Guide	1
About the manuals	1
Part names and functions	1
Installation	1
Setting up network environment	2
Viewing video on web page	2
SETUP page	2
Reboot*	2
Factory Default*	2
Safe mode	2

Ganz Security ZNT1-H Ganz G2 Fixed Thermal Quick Start Guide

Ganz Security ZNT1-H Manual

Ganz Security ZNT1-H manual content summary: