Epson TM-T70-i Technical Reference Guide
Epson TM-T70-i Manual
 |
View all Epson TM-T70-i manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson TM-T70-i manual content summary:
- Epson TM-T70-i | Technical Reference Guide - Page 1
Technical Reference Guide Product Overview Describes features and general specifications for the product. Setup Describes setup and instrallation of the product and peripherals. Application Development Information Describes how to control the printer and necessary information when you develop - Epson TM-T70-i | Technical Reference Guide - Page 2
to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. • Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those - Epson TM-T70-i | Technical Reference Guide - Page 3
For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. You must follow warnings carefully to avoid - Epson TM-T70-i | Technical Reference Guide - Page 4
this equipment, do not continue to use it. Continued use may lead to fire. Unplug the power cord immediately and contact your dealer or a Seiko Epson service center for advice. If you open the DIP switch cover, be sure to close the cover and tighten the screw after adjusting the DIP switch - Epson TM-T70-i | Technical Reference Guide - Page 5
breakage and possible injury. To avoid injury, do not insert fingers or any part of the hand in the roll paper opening where the manual cutter is installed. Do not open the roll paper cover without taking the necessary precautions, as this can result in injury from the autocutter fixed blade - Epson TM-T70-i | Technical Reference Guide - Page 6
result in injury or fire. CAUTION OT-WL01 is only for indoor use. OT-WL01 should only be used for EPSON TM Intelligent Printers. If it is installed on another device, it may result in computer failure, damage, or malfunctions. To comply with RF exposure compliance requirements, a distance - Epson TM-T70-i | Technical Reference Guide - Page 7
, and with your full understanding of problems that may occur if you do not make any security settings. Notes on Setting SSID (Service Set Identifier) For protection of security, note the following precautions when setting the SSID. • Change the SSID from the default setting. • Do not set texts by - Epson TM-T70-i | Technical Reference Guide - Page 8
Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc.; or functional/precision devices etc., you should use this - Epson TM-T70-i | Technical Reference Guide - Page 9
created to provide information on development, design, and installation of receipt issue systems and development and design of printer applications for developers. Manual Content The manual is made up of the following sections: Chapter 1 Product Overview Chapter 2 Setup Chapter 3 Application - Epson TM-T70-i | Technical Reference Guide - Page 10
Precautions 6 ■ Restriction of Use ...8 ■ About this Manual ...9 Aim of the Manual ...9 Manual Content ...9 Product Overview 15 ■ Features...15 ■ Product Product Specifications ...25 Software Specifications ...26 Intelligent Section Specifications...26 Printing Specifications...27 Character - Epson TM-T70-i | Technical Reference Guide - Page 11
TM-T70-i Dedicated AC Adapter ...34 ■ Option Specifications...35 Wireless LAN Cable Set (OT-WL01) ...35 Setup 37 ■ Flow of Setup ...37 ■ Installing the Printer ...38 Important Notes on Installation to Control the Printer 71 ■ Software and Manuals ...71 Download ...71 ■ EPSON TMNet WebConfig 72 11 - Epson TM-T70-i | Technical Reference Guide - Page 12
Starting EPSON TMNet WebConfig ...72 General Information...73 TCP/IP Information (Wired) ...74 TCP/IP Information (Wireless)...75 Web Contents Update Information...76 Time Information ...77 Wired Setting...78 TCP/IP Setting (Wired) ...79 Wireless Setting ...80 TCP/IP Setting (Wireless)...81 Device - Epson TM-T70-i | Technical Reference Guide - Page 13
for receipt ejection Software • XML printer using ePOS-Print API and ePOS-Print XML • Direct server printing with data sent from a web server to the printer (supported by ePOS- Print XML) • Status notification function that sends notification of printer status to a web server • Printer driver is - Epson TM-T70-i | Technical Reference Guide - Page 14
• Registering web pages on the TM-T70-i makes them accessible on the Web. • Methods to efficiently construct multiple systems are included. For details, see the "TM-i series Easy Setup Guide". Product Configuration Color • ECW (Epson Cool White) • EDG (Epson Dark Gray) Accessories Attachments • Roll - Epson TM-T70-i | Technical Reference Guide - Page 15
the power switch cover that comes with the TM-T70-i onto the printer to prevent inadvertent changing of the power switch, to prevent tampering, and to improve the appearance of the printer. To reset the printer when the power switch cover is installed, insert a long, thin object (such as the end - Epson TM-T70-i | Technical Reference Guide - Page 16
remaining. • Off when there is a sufficient amount of roll paper remaining. • Flashes when a self-test is in progress. ERROR LED Lights or flashes when the printer is offline. • Lights after the power is turned on or after a reset (offline). Automatically goes out after a while to indicate that the - Epson TM-T70-i | Technical Reference Guide - Page 17
PHP function with the firmware version 2.00 or later.) For details on how to connect the power supply connector and cash drawer, see "Connecting the Printer to the System" on page 48 and "Connecting the Cash Drawer" on page 44. For the Micro-USB connector, use the Micro USB (A-Micro B type - Epson TM-T70-i | Technical Reference Guide - Page 18
, a status sheet on which network parameters are printed will be ejected. (See "Confirming with a status sheet" on page 59.) • Initialization: Make sure the printer is turned on, press the push button for approximately 10 seconds. When you release the button, all setting will be initialized. (See - Epson TM-T70-i | Technical Reference Guide - Page 19
errors. Check the error codes. When connection to external devices fails, check the status LEDs at the lower rear of the printer. Automatically Recoverable Errors Printing is no longer possible when automatically recoverable errors occur. They can be recovered easily, as described below - Epson TM-T70-i | Technical Reference Guide - Page 20
High voltage error Low voltage error After R/W checking, the printer does not work correctly. The power supply voltage is extremely extremely low. CPU execution error The CPU is executing an incorrect address. Internal circuit connection error Internal circuits are not connected correctly. - Epson TM-T70-i | Technical Reference Guide - Page 21
1 Product Overview No Connection to External Devices When connection to external devices is not possible, check the status LED at the back of the printer. Status LED Orange: Booting Green: Operating normally 1 When the status LED is lit in green • Check whether the interface cable or the optional - Epson TM-T70-i | Technical Reference Guide - Page 22
, such as shop logos to be printed on receipts, can be stored. Use the TM Flash Logo Setup utility for NVRAM to register graphics. Memory Switches (Customized Value) With the memory switches (customized value), which are software switches for the printer, you can set print density, print speed, and - Epson TM-T70-i | Technical Reference Guide - Page 23
KB (both for user-defined characters and downloaded images) NV graphics data 256 KB 1 Barcode/two-dimensional code printing UPC-A, UPC-E JAN 8 (EAN 8), JAN 13 (EAN 13) CODE 39 ITF CODABAR (NW-7) CODE 93 CODE 128 PDF417 QR CODE Power supply EPSON AC ADAPTER, RA (Model: M266A) Life Mechanism - Epson TM-T70-i | Technical Reference Guide - Page 24
Web service is used. No printer driver is required.) EPSON TMNet WebConfig Network setting (Ethernet/Wireless LAN) Web contents registration ePOS-Print setting Following printers with the UB-E02 or UB-R03 embedded TM-T88V TM-T88IV* TM-T70 TM-T20* TM-T90 TM-L90* TM-U220* TM - Epson TM-T70-i | Technical Reference Guide - Page 25
UB-R03 embedded TM-T88IV TM-T70* TM-L90* TM-U220* *: Firmware Ver.3.0 or later KO Model Following printers with the UB-E02 or UB-R03 embed- ded TM-T88IV TM-L90* TM-U220* *: Firmware Ver.3.0 or later 1 Number of printers 20 printers at maximum Intelligent Section Specifications - Epson TM-T70-i | Technical Reference Guide - Page 26
Thermal line printing 180 × 180 dpi Unidirectional with friction feed (Reverse feed is not supported.) 72.2 mm, 512 dots 42 56 170 mm/s 150 mm/s 4.23 mm {1/6"} dpi: dots per inch * when the printer prints with the default print density level at 24V and 25°C {77°F}. Printing speed may be slower - Epson TM-T70-i | Technical Reference Guide - Page 27
Chapter 1 Product Overview Character Specifications Number of characters Alphanumeric characters: 95 Extended graphics: 128 × 11 pages (including user-defined page) International characters: 48 Character structure Font A (Initial setting): 12 × 24 (including 2-dot spacing in horizontal) Font B: - Epson TM-T70-i | Technical Reference Guide - Page 28
Printable Area OO OO OO OO OO In 2-divided energizing, the print position within the printable area of the thermal elements for dots 1 to 256 and 257 to 512 is shifted approximately 0.07 mm {0.0028"} as shown in the figure below in the paper feed direction. - Epson TM-T70-i | Technical Reference Guide - Page 29
Printing and Cutting Positions Chapter 1 Product Overview Manual-cutter position Autocutter blade position Center of the print dotline Approx. 15 Approx. 30 1 Paper feed direction [units: mm (All the numeric values are typical.)] - Epson TM-T70-i | Technical Reference Guide - Page 30
Electrical Characteristics Supply voltage DC 24V: DC 24V ± 5% DC 5V: DC 5V Current consumption (at 24V, 25°C, normal print density) Standby Operating Mean: Approximately 0.1A Maximum 1A for drawer kick-out driving. DC 24V Mean: Approximately 1.8A DC 5V*: Maximum 1.0A/2.5A Note: When print - Epson TM-T70-i | Technical Reference Guide - Page 31
Acoustic noise (Operating) 5 34 40 45 [°C] Ambient temperature Approximately 55 dB (Bystander position) Note) The values above are measured in the Epson evaluation condition. The acoustic noise differs depending on the paper used, printing contents, or the setting values such as print speed or - Epson TM-T70-i | Technical Reference Guide - Page 32
: Approximately 125 mm {4.92"} • Depth: Approximately 194 mm {7.64"} • Mass: Approximately 1.8 kg {3.96 lb} (except for roll paper) ‣․‧ 114 ‣‣... 255.5 [Unit: mm] 34 - Epson TM-T70-i | Technical Reference Guide - Page 33
Chapter 1 Product Overview TM-T70-i Dedicated AC Adapter Input conditions Output conditions Input voltage: AC 100V to 240V Frequency: 50/60 Hz Input current (rating): 1.3A Output voltage (rating): DC 24V ± 5% Output current (rating): 2.1A 1 35 - Epson TM-T70-i | Technical Reference Guide - Page 34
method, Encryption algorithm Power voltage Current consumption Frequency range Potential interference range Overall dimensions ELPAP07: 802. 11b/g/n wireless LAN Module (EPSON) IEEE802.11b/g/n (Wi-Fi certificated) 1 to 32 one-byte alphabet and numbers Ad hoc mode, Infrastructure mode Open+WEP - Epson TM-T70-i | Technical Reference Guide - Page 35
In this setup flow, necessary items are in a frame with a solid line. Optional items are explained in an frame with a dotted line. 1. Installing the Printer (page 38) 2. Setting the DIP Switches (page 41) 2 3. Connecting the Cash Drawer (page 44) 4. Arranging the Cables (page 46) 5. Connecting - Epson TM-T70-i | Technical Reference Guide - Page 36
. (See "Affixing Position of DF-10" on page 40.) As shown in the figure below, install the printer with a maximum tilt of 3°. Installing the printer with a tilt of more than 3° may cause the following problems. • Roll paper near end cannot be detected. • The roll paper cover will not close after - Epson TM-T70-i | Technical Reference Guide - Page 37
Chapter 2 Setup If the printer installation does not fit within the specifications shown in the figure below, the following problems may occur. • Cannot set the roll paper in the printer • Cannot cut the paper with the manual cutter Range that manual cutting is possible Area required for loading - Epson TM-T70-i | Technical Reference Guide - Page 38
118.5 Affixing Position of DF-10 When you use the affixing tapes for fixing the printer (Model: DF-10), paste them as shown in the figure below. Affixing position of the DF-10 40 - Epson TM-T70-i | Technical Reference Guide - Page 39
switches. Setting Procedure Follow the steps below to change the DIP switch settings. CAUTION Before you remove the DIP switch cover, turn the printer off. Otherwise, a short-circuit may cause the printer to malfunction. DIP switch settings are enabled only when the power is turned on or the - Epson TM-T70-i | Technical Reference Guide - Page 40
not change settings) Fixed to ON Factory setting ON OFF OFF OFF OFF ON Do not change the setting of DIP switches 2-1, 2-2, 2-6, 2-7, and 2-8. Otherwise, the printer may not operate normally. 42 - Epson TM-T70-i | Technical Reference Guide - Page 41
Chapter 2 Setup Selecting the Print Density (DIP Switch 2-3/2-4) Function Low power consumption mode Print density (Standard) Print density (Darker than standard) Print density (Dark) SW 2-3 ON OFF ON OFF SW2-4 ON OFF OFF ON If the print density is set to "Darker than standard" or "Dark" - Epson TM-T70-i | Technical Reference Guide - Page 42
drawer handled by EPSON or your dealer. a shield cable for the drawer connector cable. Two driver transistors cannot be energized simultaneously. Leave intervals longer than when sending it continuously. Be sure to use the printer power supply (connector pin 4) for the drawer power source. - Epson TM-T70-i | Technical Reference Guide - Page 43
Drawer Circuitry Chapter 2 Setup Drawer kick-out connector With shielded Drawer kick-out solenoid Printer side Drawer open/close switch User side [Drawer kick-out side] 2 45 - Epson TM-T70-i | Technical Reference Guide - Page 44
Arranging the Cables When installing cables without locking connectors (USB cable and DC 5V cable) through the cable exits on connector cover (OT-CC70), use multiple cable exits depending on the number of the cables. After installing, make sure the cables are not pinched by the connector cover. 46 - Epson TM-T70-i | Technical Reference Guide - Page 45
Doing so may result in damage to both the power supply and the printer. When installing the DC 5 V cable through the cable exits on the back, Make sure the printer's power supply is turned off, and then connect the AC adapter and AC cable. DC 24V DC 5V AC cable TM-T70-i dedicated AC adapter 47 - Epson TM-T70-i | Technical Reference Guide - Page 46
Ethernet Interface Connect the printer to a network by a LAN cable via a hub. Ethernet interface connection diagram DM-D Serial cable 10BASE-T/100BASE-TX Modular cable TM-T70-i Cash drawer Connecting the LAN interface cable CAUTION When LAN cables are installed outdoors, make sure devices - Epson TM-T70-i | Technical Reference Guide - Page 47
Chapter 2 Setup Connect a 10BASE-T/100BASE-TX cable to the 10BASE-T/100BASE-TX LAN connector by pressing firmly until the connector clicks into place. Ethernet connector 2 49 - Epson TM-T70-i | Technical Reference Guide - Page 48
printer is set and installed for both of them, only the LAN connection works. Wireless LAN interface connection diagram Access point Modular cable TM-T70 pair, 2 pieces) • Rubber cover • User's manual To connect the wireless LAN unit to the printer, you can connect directly or use the USB extension - Epson TM-T70-i | Technical Reference Guide - Page 49
Connecting the unit directly with the printer Install the wireless LAN unit to a USB connector of the printer. Chapter 2 Setup USB connector Using the USB extension cable 1 Attach the included rubber cover to the connector of the USB extension cable into which the - Epson TM-T70-i | Technical Reference Guide - Page 50
Flashing rapidly Status The wireless LAN unit is not connected to the printer. Or the printer power is OFF. This wireless LAN unit is connected to the printer and is in operation. This wireless LAN unit is connected to the printer and is in operation. This unit is communicating on a network. 52 - Epson TM-T70-i | Technical Reference Guide - Page 51
168.192.168" as the IP address. When the printer is turned on, the IP address is acquired automatically and then printed. The setting method using EPSON TMNet WebConfig is explained here. For more information about how to use EPSONNet Config, refer to the EpsonNet Config Operations Guide. For more - Epson TM-T70-i | Technical Reference Guide - Page 52
to the network. 2 Connect the TM-T70-i printer to the network, and turn printer's IP address printed on the status sheet in the address bar as shown below. http://xxx.xxx.xxx.xxx/PrinterConfigurationPage/ EPSON TMNet WebConfig starts. 6 Select [Configuration], [Wired], and then [TCP/IP]. The [TCP/IP - Epson TM-T70-i | Technical Reference Guide - Page 53
EPSON TMNet WebConfig. This printer cannot be used with the LAN connection and wireless LAN connection at the same time. When the printer is set and installed for both of them, only the LAN connection works. 5 7 2 9 6 8 1 Connect a PC for setting to the network. 2 Connect the TM-T70-i printer - Epson TM-T70-i | Technical Reference Guide - Page 54
the PC for setting, and enter the printer's IP address printed on the status sheet in the address bar as shown below. http://xxx.xxx.xxx.xxx/PrinterConfigurationPage/ EPSON TMNet WebConfig starts. 6 Select [Configuration], [Wireless], and then [TCP/IP]. The [TCP/IP Setting (Wireless)] screen appears - Epson TM-T70-i | Technical Reference Guide - Page 55
following items depending on the network mode. Chapter 2 Setup Item Network Mode SSID Ad-Hoc Channel Communication Standard Authentication Method Security Mode Default WEP Key WEP Key 1 to 4 WPA/WPA2 Pre-Shared Key 2 Description Set the communication mode (Infrastructure/Ad-Hoc). Same value as - Epson TM-T70-i | Technical Reference Guide - Page 56
Initially, Authentication Method is set to Open System and Security Mode is set to None with the firmware version 2.00 or later. To ensure security, be sure to change the settings before use. The following restrictions apply to the characters that can be specified for SSID, WEP keys, and WPA/ - Epson TM-T70-i | Technical Reference Guide - Page 57
Chapter 2 Setup Confirming Network Setting You can confirm the network setting with a status sheet or EPSON TMNet WebConfig. Confirming with a status sheet Make sure the printer is turned on, press the push button at the interface part for approximately 3 seconds. When you release the button, a - Epson TM-T70-i | Technical Reference Guide - Page 58
printer's software version. Model Shows [TM-T70-i]. Time Shows the present time and time difference Wired Shows wired LAN settings. MAC Address Shows the MAC address. Link Speed & Duplex Shows the speed of data link layer. Wired TCP/IP Shows TCP/IP settings for wired LAN. Get IP Address - Epson TM-T70-i | Technical Reference Guide - Page 59
TCP/IP Shows TCP/IP settings for wireless LAN. Get IP Address Shows the method of getting the IP address. Set using Automatic Private IP Addressing (APIPA) Shows the APIPA setting. IP Address Shows the IP address. Subnet Mask Shows the subnet mask. Default Gateway Shows the default gateway - Epson TM-T70-i | Technical Reference Guide - Page 60
Item Date of Installed Web Contents Date of Last Automatic Update Status of Last Automatic Update Description When Automatic Update Setting is enabled: Shows the date and time when - Epson TM-T70-i | Technical Reference Guide - Page 61
PC for setting. 2 Connect the TM-T70-i printer to the network, and turn it on. 3 Start up the web browser on the PC for setting, and enter the printer's IP address in the address bar as shown below. http://xxx.xxx.xxx.xxx/PrinterConfigurationPage/ EPSON TMNet WebConfig starts. 4 Select [Information - Epson TM-T70-i | Technical Reference Guide - Page 62
connection fails, follow the steps below to initialize the network setting to the default. For firmware version 3.00 and later, the TMNet WebConfig password is also initialized. 1 Load the paper on the printer and turn on the printer. 2 Push and hold the push button for 10 seconds or longer. The - Epson TM-T70-i | Technical Reference Guide - Page 63
. ePOS-Print printer is a generic term that refers to TM-i series printers such as this product as well as TM printers that support ePOS-Print. Two environments are provided for ePOS-Print. ePOS-Print API: This is an application programming interface for using ePOS-Print Service from client-side - Epson TM-T70-i | Technical Reference Guide - Page 64
browser. • No need to install drivers or plugins. • No need to set up a computer or server for printing. • You can print from a public cloud or a private cloud. • You can print out in any language supported by the web browser. • The status of the TM printer is checked automatically before printing - Epson TM-T70-i | Technical Reference Guide - Page 65
control Controllable printers Wireless LAN/ Router 2 Input terminal Web application TM-T70-i • Input terminal: Executes the web application from a browser. The browser must be HTML 5 compliant. • TM-T70-i: Receives the print document sent from the web browser, prints receipts, or controls - Epson TM-T70-i | Technical Reference Guide - Page 66
control Controllable printers Wireless LAN/ Router Input terminal TM-T70-i • Web server: The web application is installed. • Input terminal: Executes the web application from a browser (HTML 5 compliant). • TM-T70-i: Receives the print document sent from the web browser, prints receipts, or - Epson TM-T70-i | Technical Reference Guide - Page 67
for each printer. For how to print a status sheet, see "Confirming with a status sheet" on page 59. 4 Start up the web browser on the PC for setting, and enter the TM-T70-i printer's IP address in the address bar as shown below. http://xxx.xxx.xxx.xxx/PrinterConfigurationPage/ EPSON TMNet WebConfig - Epson TM-T70-i | Technical Reference Guide - Page 68
Item Description Device ID Set an ID for a device to be controlled. Model number Select an model for a device to be controlled. IP address Enter an IP address for a device to be controlled. (See the status sheet printed in Step 3.) Retry interval (ms) Set a retry interval for a device to be - Epson TM-T70-i | Technical Reference Guide - Page 69
Web Pages When you register an application on the TM-70-i printer, register web contents. Specifications of the file to names for top folders in the web application. PrinterConfigurationPage lisences technical-support cgi-bin firmware-update The maximum size of the files before - Epson TM-T70-i | Technical Reference Guide - Page 70
on, the URL differs depending on the folder structure in the zip file. ➀ http://[the TM-T70-i printer's IP address]/index.html ➁ http://[the TM-T70-i printer's IP address]/webpage/index.html ➀ epsonsample.zip ｜ ├ index.html ├ css ｜└ *.css ├ img ｜├ *.bmp ｜├ *.jpg ｜└ *.png ├ js ｜└ *.js - Epson TM-T70-i | Technical Reference Guide - Page 71
to the network, and turn it on. 3 Start up the web browser on the PC for setting, and enter the TM-T70-i printer's IP address in the address bar. EPSON TMNet WebConfig starts. 4 Select [Configuration], and then [Web Contents]. The [Web Contents Update Settings] screen appears. 5 Click [Browse - Epson TM-T70-i | Technical Reference Guide - Page 72
information about the memory switch utility, see the user's manual for the Memory Switch Setting Utility. To use the Memory Switch Setting Utility, connect the printer with a PC for setting via the Micro-USB cable. Connecting the printer with a PC via a network is not possible. Selecting the - Epson TM-T70-i | Technical Reference Guide - Page 73
application development methods used for this product. TM-i series WebConfig API User's Manual See this manual when you use API to set or check the settings for the TM-T70-i (firmware version 2.00 or later). TM-i series PHP Setup Manual See this manual when you establish the environment where you - Epson TM-T70-i | Technical Reference Guide - Page 74
, and manuals can be downloaded from one of the following URLs. For customers in North America, go to the following web site: http://www.epsonexpert.com/ and follow the on-screen instructions. For customers in other countries, go to the following web site: https://download.epson-biz.com/?service=pos - Epson TM-T70-i | Technical Reference Guide - Page 75
details, see TM Intelligent Printer WebConfig API User's Manual. Starting EPSON TMNet WebConfig Follow the steps below to start up EPSON TMNet WebConfig. 1 Start up a PC connected to the network. 2 Start up the web browser and input the printer's IP address (http:// printer's IP address) in the - Epson TM-T70-i | Technical Reference Guide - Page 76
of the TM-T70-i. Item Administrator Name Location/Person Software Version Printer Serial Number Wired MAC Address Description Shows the administrator name. Shows the user name Shows the software version of the TM-T70-i. Shows the serial number of the TM-T70-i. Shows the MAC address for wired - Epson TM-T70-i | Technical Reference Guide - Page 77
the communication mode. SSID Shows the SSID. Wireless LAN Frequency Region Shows region codes. Ad-Hoc Channel Shows the ad-hoc channel. Access Point (MAC Address) Shows the MAC address for the access point. Signal Condition Shows the signal strength. Time Shows the present time. 3 75 - Epson TM-T70-i | Technical Reference Guide - Page 78
Shows the method of getting the IP address. Shows the APIPA setting. Shows the IP address when [Get IP Address] is set to [Manual]. Shows the subnet mask when [Get IP Address] is set to [Manual]. Shows the default gateway when [Get IP Address] is set to [Manual]. Shows the method of getting the - Epson TM-T70-i | Technical Reference Guide - Page 79
using Automatic Private IP Addressing Shows the APIPA setting. (APIPA) IP Address Shows the IP address when [Get IP Address] is set to [Manual]. Subnet Mask Shows the subnet mask when [Get IP Address] is set to [Manual]. Default Gateway Shows the default gateway when [Get IP Address] is set to - Epson TM-T70-i | Technical Reference Guide - Page 80
contents (zip file) were created. When manual update setting is disabled: Shows the date and time when the web contents were uploaded. Date of Last Automatic Update Shows the latest date and time when the web contents were installed on the TM-T70-i automatically. Status of Last Automatic Update - Epson TM-T70-i | Technical Reference Guide - Page 81
Server Status Description Shows the present time. Shows whether time server is used for time setting. 3 Shows the method of getting time server. Shows the IP address or host name of the time server. Shows the result of communication with the time server. 79 - Epson TM-T70-i | Technical Reference Guide - Page 82
Wired Setting You can make settings for a wired LAN network. Item Link Speed & Duplex Submit Description Sets the speed of data link layer. Submits the setting to the TM-T70-i. 80 - Epson TM-T70-i | Technical Reference Guide - Page 83
IP Addressing Enables or disables the APIPA setting. 3 (APIPA) IP Address Sets the IP address when [Get IP Address] is set to [Manual]. Subnet Mask Sets the subnet mask when [Get IP Address] is set to [Manual]. Default Gateway Sets the default gateway when [Get IP Address] is set to [Manual - Epson TM-T70-i | Technical Reference Guide - Page 84
the optional wireless LAN cable set (OT-WL01) is used. Item Network Mode SSID Ad-Hoc Channel Communication Standard Authentication Method Security Mode Default WEP Key WEP Key 1 WEP Key 2 WEP Key 3 Description Sets the communication mode. Sets the SSID. Sets the ad-hoc channel. (Available only - Epson TM-T70-i | Technical Reference Guide - Page 85
Development Information Item WEP Key 4 WPA/WPA2 Pre-Shared Key Submit Description Sets the WEP key 4. Sets the network key. Submits settings to the TM-T70-i. Initially, Authentication Method is set to Open System and Security Mode is set to None with the firmware version 2.00 or later. To - Epson TM-T70-i | Technical Reference Guide - Page 86
IP Addressing Enables or disables the APIPA setting. (APIPA) IP Address Sets the IP address when [Get IP Address] is set to [Manual]. Subnet Mask Sets the subnet mask when [Get IP Address] is set to [Manual]. Default Gateway Sets the default gateway when [Get IP Address] is set to [Manual - Epson TM-T70-i | Technical Reference Guide - Page 87
is not possible. You can change the device ID for the TM-T70-i printer. 3 Item Description Register Device Device ID Sets the ID of a device to control. Model Sets the model of a device to control. IP Address Sets the IP address of a device to control. Retry Interval (ms) Sets the retry - Epson TM-T70-i | Technical Reference Guide - Page 88
Update Settings You can set how to install and update web contents to register on the TM-T70-i or update them. See also "Registering other settings in [Automatic Update Settings]. When it is disabled, install web contents manually. Sets the frequency of automatic update for web contents. Sets the - Epson TM-T70-i | Technical Reference Guide - Page 89
and Port Number]. Proxy URL and Port Number Sets the URL and port number for the proxy server to use. Submit Submits settings to the TM-T70-i. Web Contents Web Contents Archive File Specifies the web contents to install. Manual Update (*.zip) Upload Registers the specified web contents on the - Epson TM-T70-i | Technical Reference Guide - Page 90
Server Direct Print Setting You can set server direct print for the TM-T70-i. Item Server Direct Print ID Password URL Interval(s) Submit Description Sets whether to use the Server Direct for acquiring print data when [Server Direct Print] is set to [Enable]. Submits settings to the TM-T70-i. 88 - Epson TM-T70-i | Technical Reference Guide - Page 91
Status Notification Setting You can set the information for the administrator of the TM-T70-i. Item Administrator Name ID Password URL Interval(s) Submit Description Sets the name of the administrator of the TM-T70-i. Sets the web server ID when [Status Notification] is set to [Enable]. Sets - Epson TM-T70-i | Technical Reference Guide - Page 92
Administrator Setting You can set the information for the administrator of the TM-T70-i. Item Administrator Name Location/Person Submit Description Sets the name of the administrator of the TM-T70-i. Sets the location where the TM-T70-i is installed. Submits settings to the TM-T70-i. 90 - Epson TM-T70-i | Technical Reference Guide - Page 93
server or not for time 3 setting. Sets the method of getting the IP address/host name for the time server. Sets the IP address/host name for the time server when [Get Time Server] is set to [Manual]. Shows the result of communication with the time server. Submits settings to the TM-T70-i. 91 - Epson TM-T70-i | Technical Reference Guide - Page 94
new password. Enter the new password for confirmation. Submits settings to the TM-T70-i. A user name and a password will be required on the authentication screen when you start up this utility and when you change settings. Enter "epson" for the user name and the password you set for the password - Epson TM-T70-i | Technical Reference Guide - Page 95
Application Development Information Reset Item Factory Default Description Resets the network interface, and reboots wired LAN and wireless LAN functions after applying the changes made in the settings window. 3 Returns settings of the TM-T70-i to default ones. All settings are initialized - Epson TM-T70-i | Technical Reference Guide - Page 96
cover. 2 While pressing the FEED button, turn on the printer. (Keep pressing the FEED button until the printer starts printing.) The printer prints current status of the printer on the roll paper. When the printer finishes printing the printer status, the following message is printed and the PAPER - Epson TM-T70-i | Technical Reference Guide - Page 97
the line. 1 Open the roll paper cover. 2 While pressing the FEED button, turn on the printer. 3 Close the roll paper cover. Data received from then on is printed out from the printer in hexadecimal numbers and their corresponding characters. 4 To quit the hexadecimal dumping mode, turn off the - Epson TM-T70-i | Technical Reference Guide - Page 98
You can perform settings for multiple TM-i devices quickly and efficiently. If you are using a printer that can be controlled (a TM printer connected to a network), you can also perform their network settings at the same time. USB Memory Web contents file setting.ini file -WebConfig -IP address 96 - Epson TM-T70-i | Technical Reference Guide - Page 99
Handling This chapter describes basic handling of the printer. Installing and Replacing Roll Paper WARNING Do not open the roll paper cover during printing. The printer may be damaged. Do not touch the manual cutter with your hands when installing or replacing the roll paper. Otherwise, you - Epson TM-T70-i | Technical Reference Guide - Page 100
4 Pull out some roll paper, and make sure that the roll paper is set between the paper guides. Paper guides 5 Close the roll paper cover. 6 Tear off the roll paper. 92 - Epson TM-T70-i | Technical Reference Guide - Page 101
93.) because it can be very hot after printing. 1 Turn off the printer and press the cover open lever to open the roll paper cover. 2 Cleaning the Thermal Head Epson recommends cleaning the thermal head periodically (generally every 3 months) to maintain receipt print quality. CAUTION After - Epson TM-T70-i | Technical Reference Guide - Page 102
rated current of the external devices by checking the descriptions on the devices or manuals. Do not use a device whose rated current is unclear. Use the . When using the printer, make sure the protective cover fits firmly into place. When LAN cables are installed outdoors, make sure devices - Epson TM-T70-i | Technical Reference Guide - Page 103
Preparing for Transport Follow the steps below to transport the printer. 1 Turn off the printer. 2 Confirm that LED is off. 3 Remove the power supply connector. 4 Remove the roll paper. 5 Pack the printer upright. Chapter 4 Handling 4 95 - Epson TM-T70-i | Technical Reference Guide - Page 104
96 - Epson TM-T70-i | Technical Reference Guide - Page 105
Appendix Appendix Character Code Tables The character code tables show only character configurations. They do not show the actual print pattern. "SP" in the table shows a space. Common to All Pages When International character set (See "International Character Sets" on page 109.) is USA: HEX - Epson TM-T70-i | Technical Reference Guide - Page 106
Page 0 [PC437: USA, Standard Europe] HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 - Epson TM-T70-i | Technical Reference Guide - Page 107
Appendix Page 1 (Katakana) HEX 8 9 A B C D E F 0 ؤ ┴ SP 㩊 㩚 ═ ؖ 128 144 160 176 192 208 224 240 1 إ ┬ 㨫 㨻 㩋 㩛 ╞ 129 145 161 177 193 209 225 241 2 ا ┤ 㨬 㨼 㩌 㩜 ╪ ᐕ 130 146 162 178 194 210 226 242 3 ئ ├ 㨭 㨽 㩍 㩝 ╡ 131 - Epson TM-T70-i | Technical Reference Guide - Page 108
Page 2 (PC850: Multilingual) HEX 8 9 A B C D E F 0 Ç É á ░ └ ð Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ Ð β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô 130 146 162 178 194 210 226 242 3 â ô ú │ ├ Ë Ò ¾ 131 147 163 179 - Epson TM-T70-i | Technical Reference Guide - Page 109
Appendix Page 3 (PC860: Portuguese) HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü À í ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é È ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 - Epson TM-T70-i | Technical Reference Guide - Page 110
Page 4 (PC863: Canadian-French) HEX 8 9 A B C D E F 0 Ç É ¦ ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü È ´ ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é Ê ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 163 - Epson TM-T70-i | Technical Reference Guide - Page 111
Appendix Page 5 (PC865: Nordic) HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 163 - Epson TM-T70-i | Technical Reference Guide - Page 112
Page 16 (WPC1252) HEX 8 9 A B C D E F 0 € SP SP ° À Ð à ð 128 144 160 176 192 208 224 240 1 SP ' ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 , ' ¢ ² Â Ò â ò 130 146 162 178 194 210 226 242 3 ƒ " £ ³ Ã Ó ã ó 131 147 163 179 195 - Epson TM-T70-i | Technical Reference Guide - Page 113
Appendix Page 17 (PC866: Cyrillic #2) HEX 8 9 A B C D E F 0 А Р а ░ └ ╨ р Ё 128 144 160 176 192 208 224 240 1 Б С б ▒ ┴ ╤ с ё 129 145 161 177 193 209 225 241 2 В Т в ▓ ┬ ╥ т Є 130 146 162 178 194 210 226 242 3 Г У г │ ├ ╙ у є 131 - Epson TM-T70-i | Technical Reference Guide - Page 114
Page 18 (PC852: Latin2) HEX 8 9 A B C D E F 0 Ç É á ░ └ đ Ó - 128 144 160 176 192 208 224 240 1 ü Ĺ í ▒ ┴ Ð β ˝ 129 145 161 177 193 209 225 241 2 é ĺ ó ▓ ┬ Ď Ô ˛ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ Ë Ń ˇ 131 147 163 179 - Epson TM-T70-i | Technical Reference Guide - Page 115
Appendix Page 19 (PC858: Euro) HEX 8 9 A B C D E F 0 Ç É á ░ └ ð Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ Ð β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô 130 146 162 178 194 210 226 242 3 â ô ú │ ├ Ë Ò ¾ 131 147 163 - Epson TM-T70-i | Technical Reference Guide - Page 116
Page 255 (User-Defined Page) HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F 8 9 A B C D E F SP SP SP SP SP SP SP SP 128 144 160 176 192 208 224 240 SP SP SP SP SP SP SP SP 129 145 161 177 193 209 225 241 SP SP SP SP SP SP SP SP 130 146 162 178 194 210 226 - Epson TM-T70-i | Technical Reference Guide - Page 117
Appendix International Character Sets Country ASCII code (Hex) 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E USA France Germany U.K. Denmark I Sweden Italy Spain I Pt Ja pan Norway Denmark II Spain II Latin America Korea # $@ [ W - Epson TM-T70-i | Technical Reference Guide - Page 118
110
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
 |
 |
Describes character code tables.
Describes how to control the printer and necessary information
when you develop applications.
Describes setup and instrallation of the product and peripherals.
Describes how to handle the product.
Describes features and general specifications for the product.
Technical Reference Guide
M00041503
Rev. D
Product Overview
Setup
Application Development Information
Handling
Appendix