Epson TM-L90 Technical Reference

Epson TM-L90 Manual

Get Epson TM-L90 PDF manuals and user guides View all Epson TM-L90 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson TM-L90 manual content summary:

  • Epson TM-L90 | Technical Reference - Page 1
    Peeler Model Technical Reference Guide 410019405 Rev. F
  • Epson TM-L90 | Technical Reference - Page 2
  • Epson TM-L90 | Technical Reference - Page 3
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Cautions ❏ No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson
  • Epson TM-L90 | Technical Reference - Page 4
    For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. WARNING: You must follow warnings carefully to
  • Epson TM-L90 | Technical Reference - Page 5
    -L90/TM-L90 Peeler Model Technical Reference Guide WARNING: ❏ Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire or electric shock. Immediately unplug the equipment. ❏ Only disassemble this product as described in this manual
  • Epson TM-L90 | Technical Reference - Page 6
    on the manual cutter • When you remove printed paper • When you perform other operations such as loading/replacing roll paper ❏ Do not open the roll paper cover after a full evaluation. Modular Connector Use the modular connectors specifically designed for the cash drawer for this product. Do not
  • Epson TM-L90 | Technical Reference - Page 7
    TM-L90/TM-L90 Peeler Model Technical Reference Guide About This Manual Aim of the Manual This manual was created to provide all information necessary for system planning, design, installations and application of the printer for designers and developers of POS systems. Manual Content The manual
  • Epson TM-L90 | Technical Reference - Page 8
    Part Names (TM-L90 Peeler Model 16 Paper FEED button inside the printer 17 Control Panel 17 Power Switch 19 Power Switch Cover 20 Mode Switch (TM-L90 Peeler Model Only 21 Connectors 22 Chapter 2 Setup Setup Flow 23 Installation Procedures 24 Precaution For Installation 24 Instructions for
  • Epson TM-L90 | Technical Reference - Page 9
    Advanced Printer Driver 85 EPSON OPOS ADK 87 ESC/POS Commands 90 Various Utilities 91 Sensors 91 Paper Sensors 91 Printer Cover Sensor 92 Label Peeling Sensor (Peeler Specification Only 94 Barcode Printing 94 CODE 128 Barcode 95 Precautions for Two-Dimensional Code Printing 99 NV Memory
  • Epson TM-L90 | Technical Reference - Page 10
    items for Memory Switch Setting Mode 121 Setting items of TM-L90 4** models 121 Setting items of TM-L90 other than 4** models 125 Setting items of TM-L90 Peeler 39* models 126 Setting items of TM-L90 Peeler other than 39* models 128 Product Specifications 130 Product Specifications 130 Print
  • Epson TM-L90 | Technical Reference - Page 11
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Page 30 (TCVN-3: Vietnamese 187 Page 31 (TCVN-3: Vietnamese 188 Page 32 (PC720: Arabic 189 Page 33 (WPC775: Baltic Rim 190 Page 34 (PC855: Cyrillic
  • Epson TM-L90 | Technical Reference - Page 12
    12
  • Epson TM-L90 | Technical Reference - Page 13
    .11b for the other models) TM-L90 4** models and TM-L90 Peeler 39* models may have the build-in-USB. 1.1.2 Accessories TM-L90 ❏ Start Here ❏ Label roll paper ❏ Manual CD ❏ Power switch cover ❏ Control panel label used for horizontal installation ❏ Paper exit guide for horizontal installation ❏ Roll
  • Epson TM-L90 | Technical Reference - Page 14
    ❏ AC cable* * May not be included depending on the printer model. TM-L90 Peeler Model ❏ Start Here ❏ Label roll paper ❏ Manual CD ❏ Power switch cover ❏ Operation label (an instruction label for the peeler open lever and the cover open lever) ❏ Roll paper spacer ❏ Screw for installation of the roll
  • Epson TM-L90 | Technical Reference - Page 15
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 1.2 Name and Description of Each Part 1.2.1 Part Names (TM-L90) Power switch Rocker switch (with a power switch soft cover) or Non-locking push button Cutter cover Perforation to pass the cables through FEED Button Manual cutter Cover open
  • Epson TM-L90 | Technical Reference - Page 16
    Cover open lever FEED Button Control panel Cutter cover Label peeling sensor Manual cutter Peeler cover Wiring knockout Roll paper cover Part Names of TM-L90 Peeler Model * Refer to page 44 for the DIP switch positions. (available only for TM-L90 Peeler other than 39* models) 16 Product Overview
  • Epson TM-L90 | Technical Reference - Page 17
    /TM-L90 Peeler Model Technical Reference Guide 1.2.3 Paper FEED button inside the printer Another FEED button is located under the roll paper cover. Paper FEED button (inside the printer) 1.2.4 Control Panel FEED Button PAPER OUT LED ERROR LED POWER LED FEED button (with the TM-L90) When using label
  • Epson TM-L90 | Technical Reference - Page 18
    or when the printer waits for the macro execution switch to go on. PAPER OUT LED (with the TM-L90 Peeler Model) ❏ Lights when there is no more roll paper or there is little remaining. (Default setting. The LED condition varies according to the memory switch settings. Refer to "Memory Switch Settings
  • Epson TM-L90 | Technical Reference - Page 19
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 1.2.5 Power Switch Refer to "Printer Part Names" on page 15 for the power switch location. The type of the power switch differs, depending on models and functions may differ, depending on the models. Therefore, be sure to check the type of the
  • Epson TM-L90 | Technical Reference - Page 20
    cover, to turn on or off the TM printer, press the power switch through the hole in the power switch cover. Attach the cover as shown in the illustrations below. TM-L90 4** models, TM-L90 Peeler 39* models 1 2 3 TM-L90 other than 4** models, TM-L90 Peeler other than 39* models 1 2 WARNING: If
  • Epson TM-L90 | Technical Reference - Page 21
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 1.2.7 Mode Switch (TM-L90 Peeler Model Only) With the TM-L90 Peeler Model, you can select the peeling issuing mode and continuous issuing mode with the mode switch. The mode switch switches between the peeling issuing mode and continuous issuing
  • Epson TM-L90 | Technical Reference - Page 22
    located on the lower rear side of the printer. The connector panel differs, depending on the models. TM-L90 4** models, TM-L90 Peeler 39* models power supply connector USB interface drawer kick connector TM-L90 other than 4** models, TM-L90 Peeler other than 39* models Connector Panel Note: The
  • Epson TM-L90 | Technical Reference - Page 23
    Chapter 2 Setup TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.1 Setup Flow Before using the printer, you need to set various settings to increase the printer's functionality. Configure the printer appropriately depending on the environment. Determine how to install the printer (install
  • Epson TM-L90 | Technical Reference - Page 24
    on the power supply or other cables or other objects. • Consider vibration during paper cutting and drawer usage. Take measures to prevent the printer from moving. ❏ TM-L90 Peeler Model • Locate the printer on a flat surface. • Avoid locations susceptible to dust and other foreign matter. • Avoid
  • Epson TM-L90 | Technical Reference - Page 25
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.2.2 Instructions for Installation The TM-L90 can be placed vertically (paper outlet in front), horizontally (paper outlet at the top), or attached to a wall (using the optional wall hanging set WH-10). With the TM-L90 Peeler Model, you can use
  • Epson TM-L90 | Technical Reference - Page 26
    in the illustration below. Control panel label Note: To hang the printer on the wall, see the Wall Hanging Bracket Set Installation Manual provided with the WH-10 for instructions. When you use TM-L90 horizontally, peel off the backing sheet of the paper exit guide and attach it as shown below to
  • Epson TM-L90 | Technical Reference - Page 27
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.3 Adjusting Roll Paper Near-End Detection Position 2.3.1 With TM-L90 Below are three situations when roll paper N.E. detector adjustment is required. ❏ When changing the way of installation. (VerticallyHorizontally) ❏ To adjust the location of
  • Epson TM-L90 | Technical Reference - Page 28
    that its tab comes out from the hole near the bottom of the printer. (Refer to "Adjusting Roll Paper Near-End Detection Position" on page 27, "Adjustment Positions of N.E. Detector change of installation, move the roll paper N.E. detector as the above arrow shows while holding down the detector. 28
  • Epson TM-L90 | Technical Reference - Page 29
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 5. To fine tune the amount of remaining paper that is paper N.E. detector varies depending on the method of printer installation (vertical/horizontal). N.E. Detector Holder Adjustment Position Number Specified Thermal Paper N.E. Detector Setup 29
  • Epson TM-L90 | Technical Reference - Page 30
    6. Tighten the detector adjustment screw using a coin or similar tool. 7. Move the N.E. detect lever by hand (finger) to confirm that it moves smoothly. Check that the N.E. detect lever is operating properly. 8. Load the roll paper. 9. Close the roll paper cover. 30 Setup
  • Epson TM-L90 | Technical Reference - Page 31
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.3.2 With the TM-L90 Peeler Model In the following 2 cases, it is necessary to adjust the position of the roll paper near end sensor. ❏ When adjusting the detection position according to the thickness of the roll paper core ❏ When adjusting the
  • Epson TM-L90 | Technical Reference - Page 32
    the roll paper near end sensor so that the claw of the roll paper near end sensor projects from the hole near the bottom of the device. (Refer to window. 6. To make fine adjustments to the amount of paper remaining detected by the roll paper near end sensor, finely adjust the position of the near
  • Epson TM-L90 | Technical Reference - Page 33
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: Move the N.E. detector in the direction shown by arrow. Adjustment direction N.E. detector holder Adjustment scale #1 #2 Near end sensor holder Outside diameter of specified thermal paper Near end sensor adjustment position Setup 33
  • Epson TM-L90 | Technical Reference - Page 34
    7. Using a coin or similar tool, tighten the sensor adjustment screw. 8. Push the near end sensor with your finger and check that it moves smoothly. push the near end sensor with your finger and check that it moves smoothly 9. Set the roll paper. 10. Close the roll paper cover. 34 Setup
  • Epson TM-L90 | Technical Reference - Page 35
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.4 Connecting AC adapter (PS-180) Be sure to use the PS-180 or the equivalent product as the AC adapter. CAUTION: Be sure to remove the AC cable from the wall outlet whenever connecting or disconnecting the AC adapter to the printer . Setup 35
  • Epson TM-L90 | Technical Reference - Page 36
    connector of the DC cable onto the DC connector (labeled DC24V). Power supply connector Power Supply Connector Note: The . When removing the DC cable connector from the printer, first confirm that the AC cable has been Refer to "Unrecoverable errors" on page 116 for the LED flashing
  • Epson TM-L90 | Technical Reference - Page 37
    . Contact the nearest Epson service center if you'd like to do the above change. To disable the autocutter, change the memory switch (MSW2-2) settings. (Refer to "Memory Switch Settings" on page 44). Performing full cut without the paper exit guide when the printer installed horizontally may cause
  • Epson TM-L90 | Technical Reference - Page 38
    2.5.2 Setting Procedure 1. Turn off the power. 2. Pull the cover open lever, and open the roll paper cover. 3. Push the body case outward (in the direction of the 2 arrows) and remove the cutter cover. top of the cutter unit upward and remove it. Loosen this screw Cutter unit Lift upwards 38 Setup
  • Epson TM-L90 | Technical Reference - Page 39
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 6. Moving the cutter unit in a lateral direction, shift to the dowel position of the desired cut method. cutter unit again using the removed screw and the loosened screw. 8. Install the cutter cover. 9. Close the roll paper cover. Setup 39
  • Epson TM-L90 | Technical Reference - Page 40
    Setting Roll Paper Width The TM-L90 / TM-L90 Peeler Model uses a roll paper 80 mm wide in the default state. When using a roll paper 38 to 70 mm wide with this printer, attach the roll paper spacer in accordance with the following procedure. Note: If a printer has already been used, the paper width
  • Epson TM-L90 | Technical Reference - Page 41
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 4. Push the roll paper spacer until it clicks. Note: Check that the roll paper spacer slides smoothly from side to side. 5. Slide the roll paper spacer side-to-side and set it to the appropriate position. Use the measurement lines if necessary.
  • Epson TM-L90 | Technical Reference - Page 42
    have the DIP switches for settings. ❏ TM-L90 other than 4** models ❏ TM-L90 Peeler other than 39* models The DIP switches are located inside the printer as shown the picture below. DIP switch cover Before setting DIP switches, remove the DIP switch cover. Note: Set the DIP switches after turning
  • Epson TM-L90 | Technical Reference - Page 43
    TM-L90/TM-L90 Peeler Model Technical Reference Guide DIP switch settings (Serial interface model) SW No. Function ON OFF 1 Enable/disable Power Switches power supply On/ Power switch is used to switch. Off using commands. switch power On/Off. (Power switch is disabled.) 2 Select for
  • Epson TM-L90 | Technical Reference - Page 44
    Utility, refer to the user's manual of the utility. For usage of the Memory Switch Setting Mode, see "Memory switches of TM-L90" on page 45 for TM-L90 4** models, TM-L90 Peeler 39* models, or "Memory switches of TM-L90 Peeler Model" on page 50 for TM-L90 other than 4** models, TM-L90 Peeler other
  • Epson TM-L90 | Technical Reference - Page 45
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.8.1 Memory switches of TM-L90 In the following tables, "✓" interface [Msw1-5]: Valid only for parallel interface [Msw1-7], [Msw1-8]: Not available for TM-L90 4** models Msw2 Msw Function 2-1 (Reserved) 2-2 Autocutter function 2-3 (Reserved) to
  • Epson TM-L90 | Technical Reference - Page 46
    [Msw8-2] is OFF and the printer recovers from a paper layout error, the printer feeds the paper to the next print starting position. (*3) When using paper without black mark (excluding label roll paper), when the roll paper cover is closed, the printer feeds the paper for the amount set with [Msw7
  • Epson TM-L90 | Technical Reference - Page 47
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Msw8 Msw Function Initial Msw Setting Msw Setting Off On setting utility Mode 8-1 (Reserved) - - Off 8-2 User operation for recovery Send the error Send the error Off ✓ ✓ from paper layout error recovery recovery command or
  • Epson TM-L90 | Technical Reference - Page 48
    , Dark ✓ Buzzer selection: Internal, Option, Disable ✓ Buzzer frequency: Continuous, 1 time, No sound Sound pattern: Pattern A, B, C, D, or E (Refer to "Setting items of TM-L90 4** models" on page 121, about the initial settings.) Msw Setting Mode ✓ ✓*1 ✓ ✓ ✓ 3 ✓ *1: Not available for
  • Epson TM-L90 | Technical Reference - Page 49
    TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ Depending on the paper type, it is recommended to set the print density as shown in the table below for the best print quality. Receipt Label Paper these settings are valid only when the DIP switch 1-2 is Off. USB communication conditions (
  • Epson TM-L90 | Technical Reference - Page 50
    2.8.2 Memory switches of TM-L90 Peeler Model In the following tables, "✓" shows that the setting can be set by the utility or the setting mode. Msw1 Msw Function 1-1 Transmission of Power-
  • Epson TM-L90 | Technical Reference - Page 51
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Msw7 (only for 39* models) Msw Function 7-1 (Reserved) to 7-7 7-8 Function when FEED button is pressed Off - Feed to the next print starting position On - Feed to the manual cutting position Initial Msw Setting Msw Setting setting utility
  • Epson TM-L90 | Technical Reference - Page 52
    the power is turned on or the cover is opened/closed if the paper layout is not set. Refer to "Setting Paper Layout" on page 59 for the paper layout. When [Msw 8-6] is set to "Feeding paper to the print starting position at power on is disabled", the printer does not execute the operation of feeding
  • Epson TM-L90 | Technical Reference - Page 53
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Customized values Item NV user memory capacity NV graphics memory capacity Print density Print speed Default character code table*1 Default international character*1 Number of divisions of thermal head energizing Paper selection (monochrome or
  • Epson TM-L90 | Technical Reference - Page 54
    7-bits, 8-bits Msw Setting Msw Setting utility Mode ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Note: For models other than 4** models, these settings are valid only when the DIP switch 1-2 is Off. USB communication conditions (only for 39* models) This setting is valid for the built-in USB. Item Class Option
  • Epson TM-L90 | Technical Reference - Page 55
    Loading Method TM-L90/TM-L90 Peeler Model Technical Reference Guide WARNING: Do not open the roll paper cover (for the TM-L90 Peeler Model, do not open the peeler cover and the roll paper cover) during the operation. Doing so may damage the printer. Do not touch the manual cutter with your hands
  • Epson TM-L90 | Technical Reference - Page 56
    2.9.2 With the TM-L90 Peeler Model With the TM-L90 Peeler, the paper loading method differs depending on whether peeling issuing or continuous issuing is used. They are explained as follows. Paper setting with peeling issuing 1. Pull the peeler open lever forward, and open the peeler cover. 2. Pull
  • Epson TM-L90 | Technical Reference - Page 57
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 7. As shown in the following figure, pull the end of the paper to the bottom of the square hole above the manual cutter (label peeling sensor), and close the roll paper cover. Note: Matching the leading edge of the roll paper with the printed
  • Epson TM-L90 | Technical Reference - Page 58
    , and open the peeler cover. 2. Pull the cover open lever, and open the roll paper cover. 3. If there is roll paper with little paper remaining inside the printer, take it out. 4. Put new roll paper in the printer as shown in the following figure. 5. Slide the mode switch to the left (continuous
  • Epson TM-L90 | Technical Reference - Page 59
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 6. As shown in the following figure, pull the end of the paper to the bottom of the square hole above the manual cutter (label peeling sensor). Note: Matching the leading edge of the roll paper with the printed marks on the printer ensures that
  • Epson TM-L90 | Technical Reference - Page 60
    labels and remember the label paper size. See the instructions below. ❏ TM-L90 setting procedure (Procedure for setting the paper type and size to the printer) 1. Install the printer. 2. Connect the power and other cables. 3. Open the roll paper cover. 4. Set the roll paper in the printer. 60 Setup
  • Epson TM-L90 | Technical Reference - Page 61
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 5. With the roll paper cover open, turn on the power while pressing the FEED button inside the printer. (Keep pressing the FEED button until the ERROR LED comes on.) 6. Check that the ERROR LED is on, and release the FEED button. 7. Press the
  • Epson TM-L90 | Technical Reference - Page 62
    the ejection path, and close the roll paper cover. The printer feeds several labels and remembers the label paper size. This completes the task. 6. For peeling issuing, after setting the paper, the PAPER OUT LED flashes. To print, insert the label into the peeler path, and press the FEED button. If
  • Epson TM-L90 | Technical Reference - Page 63
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: L1 and L2 are measured by the printer. See the following sketch for the lengths L1 to L7. Parameters Calculated for Automatic Layout Setting ❏ Manual paper layout setting Manual paper layout setting is to directly enter paper data into the
  • Epson TM-L90 | Technical Reference - Page 64
    For the Memory Switch Setting Utility and ESC/POS commands, refer to "Introduction of Control Methods" on page 85. When using the Advanced Printer Driver (APD) or ESC/POS commands, set the print area as required. The print area position influences the paper layout. When using label paper with black
  • Epson TM-L90 | Technical Reference - Page 65
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Chapter 3 Connecting to the Host Computer and Options 3.1 Connecting the Cable This printer has 5 types of interface, serial, parallel, USB, Ethernet, and wireless LAN. The method of connecting such options as a customer display varies depending
  • Epson TM-L90 | Technical Reference - Page 66
    : The types of cable (Type A or B) varies depending on the combination of the operation method and the handshake for the TM printer. You can operate the TM printer by a Windows driver, OPOS, or ESC/POS commands. Xon/Xoff, DTR/DSR or RTS/CTS are available as handshake control. See tables in the
  • Epson TM-L90 | Technical Reference - Page 67
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: Refer to Chapter 5 for the Windows driver, OPOS ADK, and ESC/POS commands. Refer to "Connecting the Cable" on page 65 for the cable connection procedure. DTR/DSR control is available for OPOS. Xon/Xoff or CTS/RTS control
  • Epson TM-L90 | Technical Reference - Page 68
    Pass-through Connections TM printer is connected to DM-D via serial port and DM-D is connected to the host PC via serial port. The following table shows the application control and cable connection types. Application control TM side control setting Xon/Xoff (except OPOS) Xon/Xoff Not available
  • Epson TM-L90 | Technical Reference - Page 69
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 3.2.2 With the Parallel (IEEE1284) Interface TM printer is connected to the host PC via parallel port mounting parallel interface board (UB-P**). DM-D is connected to the host PC via serial port or
  • Epson TM-L90 | Technical Reference - Page 70
    PC via USB. The second TM printer can be connected via a self-powered USB hub from the printer connected to the host PC. *1 Only the printer with the USB hub function allows another TM printer to be connected using a USB cable. *2 Epson does not supply the port driver or similar program necessary to
  • Epson TM-L90 | Technical Reference - Page 71
    the User's Manual packed with your customer display. Note: TM-L90 other than 4** models or TM-L90 Peeler other than 39* models have the DIP switches. TM-L90 4** models or TM-L90 Peeler 39* models do not have the DIP switches; however, various functions can be set with memory switches. For detailed
  • Epson TM-L90 | Technical Reference - Page 72
    cable into the ferrite core. 3.2.4 With the Ethernet Interface (TM-L90 only) TM printer with the Ethernet interface is connected to a network with the Ethernet cable via a Hub. 10BASE-T/100BASE-TX Note: The Ethernet interface TM printer does not accept a customer display (DM-D). Connect
  • Epson TM-L90 | Technical Reference - Page 73
    Connection procedure TM-L90/TM-L90 Peeler Model Technical Reference Guide CAUTION: Connecting devices directly to LAN cables that are installed outdoors will expose them to damage from power surges caused by lightning and other inductive
  • Epson TM-L90 | Technical Reference - Page 74
    the properties of the driver or outputting a pulse signal by a command. The internal buzzer cannot change the buzzer volume and sound pattern but can change the buzzer frequency. When using the internal buzzer, you need to enable the internal buzzer with the memory switch. The buzzer setting is
  • Epson TM-L90 | Technical Reference - Page 75
    TM-L90/TM-L90 Peeler Model Technical Reference Guide CAUTION: Since the buzzer drive signal and the cash drawer drive signal are common in the printer, do not use the same connector pin numbers to output the signal for the buzzer and the cash drawer. Note: For detailed information about ESC/
  • Epson TM-L90 | Technical Reference - Page 76
    76 Connecting to the Host Computer and Options
  • Epson TM-L90 | Technical Reference - Page 77
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Chapter 4 Setting/Checking Modes 4.1 Setting/Checking Modes of TM-L90 4** models, TM-L90 Peeler 39* models Besides the ordinary print mode, the printer has the following modes to set or check settings of the printer. ❏ Self-test Mode ❏ NV Graphics
  • Epson TM-L90 | Technical Reference - Page 78
    1 and 2, the following guidances are printed, the PAPER OUT LED flashes, and instructs the user's operations. 1. Continuing self-test guidance reset signal ❏ Print density ❏ Power-on notification setting ❏ Paper width setting ❏ Paper type ❏ All types of sensor thresholds ❏ Print speed setting
  • Epson TM-L90 | Technical Reference - Page 79
    TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ Memory switch settings Follow the steps below. 1. Close the roll paper cover. 2. Turn on the loaded text. After "*** completed ***" is printed, the printer initializes and switches to standard mode. 4.1.2 NV Graphics Information Print Mode You
  • Epson TM-L90 | Technical Reference - Page 80
    and Reboot Printer". 4.1.3 Memory Switch Setting Mode Use the following procedure to start this mode. 1. Close the roll paper cover. memory switch setting mode (Customize Value Settings). A guidance for the Memory switch setting mode is printed, and the PAPER OUT LED flashes. TM-L90 TM-L90 Peeler
  • Epson TM-L90 | Technical Reference - Page 81
    TM-L90/TM-L90 Peeler Model Technical Reference Guide for Memory Switch printer. Keep pressing the button until the ERROR LED comes on. 3. For TM-L90, close the roll paper cover. For TM-L90 Peeler, close the roll paper cover, and then after loading paper in the paper path, press the paper feed switch
  • Epson TM-L90 | Technical Reference - Page 82
    in undesirable results. 4.2 Setting/Checking Modes of TM-L90 other than 4** models, TM-L90 Peeler other than 39* models Besides the ordinary print mode, the printer has the following modes to set or check settings of the printer. ❏ Self-test Mode ❏ Memory Switch Setting Mode (page 83) ❏ Hexadecimal
  • Epson TM-L90 | Technical Reference - Page 83
    TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ Power-on notification setting ❏ Print density ❏ Setting status for power ON ❏ Paper width setting ❏ Paper type ❏ All types of sensor thresholds ❏ Print speed setting ❏ Dip switch settings ❏ Memory switch settings Follow the steps below. 1. Close
  • Epson TM-L90 | Technical Reference - Page 84
    while pressing FEED button inside the printer. Keep pressing the button until the ERROR LED comes on. 3. For TM-L90, close the roll paper cover. For TM-L90 Peeler, close the roll paper cover, and then after loading paper in the paper path, press the paper feed switch. Data received after this is
  • Epson TM-L90 | Technical Reference - Page 85
    The TM printer can print and be controlled by any of the following three methods. 1. Windows printer driver (EPSON Advanced Printer Driver) 2. EPSON OPOS ADK 3. ESC/POS commands Depending on the driver and interface used, the IP setup tool for Ethernet specifications, USB device driver, printing
  • Epson TM-L90 | Technical Reference - Page 86
    • Label: For printing label paper Sample programs Sample programs in Visual Basic and Visual C++ to use Status API can be installed. Manuals The following manuals can be installed. ❏ With TM-L90 • Driver: User's Manual • Status API: Reference Manual ❏ With the TM-L90 Peeler Model • User's Guide
  • Epson TM-L90 | Technical Reference - Page 87
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 5.1.1.3 EPSON Advanced Printer Driver Support Environment Supported interfaces • Serial, Parallel, USB, Ethernet, Wireless LAN Supported OSs (with confirmation of system operation) For details on the supported operating systems, see the release
  • Epson TM-L90 | Technical Reference - Page 88
    developers have to consider. The functions are: Support with the Epson-original Direct IO with a parameter, the power-on notification, and off-line buffer clear processing. Note: For detailed information on the API functions, see the UnifiedPOS specification available at the following web site: http
  • Epson TM-L90 | Technical Reference - Page 89
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 5.1.2.1 EPSON OPOS ADK (OPOS Control) Overview OPOS Control included with EPSON OPOS ADK has the following features. ❏ Supplies CO for each device class and SO for Epson devices. ❏ Direct IO with parameters available. • Gets the maintenance
  • Epson TM-L90 | Technical Reference - Page 90
    information on the ESC/POS commands, see the ESC/POS Command Reference. For details on how to obtain this manual, see "Introduction of Control Methods" on page 85. Note: The printer of Ethernet specifications requires the IP setup utility separately. For details on how to obtain the utility, see
  • Epson TM-L90 | Technical Reference - Page 91
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 5.1.4 Various Utilities We provide the utilities as described below. Get the utilities from the following URL. For customers in North America, go to the following web site: http://www.epsonexpert.com/ and follow the on-screen instructions. For
  • Epson TM-L90 | Technical Reference - Page 92
    affect the status reported by the roll paper end sensor. Note: When OPOS or Advanced Printer Driver is used, do not change the default setting of the memory switch. 5.2.2.2 Offline This printer is not equipped with an online/offline switch. The printer goes offline under the following conditions
  • Epson TM-L90 | Technical Reference - Page 93
    TM-L90/TM-L90 Peeler Model Technical Reference Guide • During the self test. • When the roll paper cover is open. • During paper feeding using the FEED button. • When the printer stops printing due to a paper-end (in cases when an empty paper supply is detected by roll paper end detector or when it
  • Epson TM-L90 | Technical Reference - Page 94
    due to misdetection, and the printer continues waiting for label removal status. In this case, press the FEED button once to return the paper to the next label printing start position. 5.3 Barcode Printing The TM-L90 / TM-L90 Peeler Model can print the types of barcode shown below. UPC-A, UPC-E JAN
  • Epson TM-L90 | Technical Reference - Page 95
    -L90/TM-L90 Peeler Model Technical Reference Guide QRCode Composite Symbology* DataMatrix* *: Available only for TM-L90 4** models or TM-L90 Peeler 39* models Refer to each document of OPOS, Printer Driver or ESC/POS commands for the setting/ printing procedures of each barcode. 5.4 CODE 128 Barcode
  • Epson TM-L90 | Technical Reference - Page 96
    Printable characters for code set A characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code NUL 00 0 ( 28 40 P 50 80 SOH 01 1 ) 29 41 Q 51 81 STX
  • Epson TM-L90 | Technical Reference - Page 97
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Printable characters for code set B characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code
  • Epson TM-L90 | Technical Reference - Page 98
    Printable characters for code set C characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code 00 00 0 40 28 40 80 50 80 01 01 1 41 29 41 81 51 81
  • Epson TM-L90 | Technical Reference - Page 99
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 5.5 Precautions for Two-Dimensional Code Printing This printer can print two-dimensional codes. The following two-dimensional codes can be printed. ❏ PDF417 ❏ QRCode ❏ MaxiCode ❏ Composite Symbology* ❏ DataMatrix* *: Available only for TM-L90 4**
  • Epson TM-L90 | Technical Reference - Page 100
    with "Q" to find information relating to your question or problem. 2. Then follow the instructions described in the "A" sentence below it. Q: Print data unit and printer settings so that they match. Corrective procedure 1. Confirm the serial communication cable. Confirm the specification of cable
  • Epson TM-L90 | Technical Reference - Page 101
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 2. Confirm DIP SW 1-2. Printer serial communication condition can be set by DIP SW and memory switch. When the printer is powered on, DIP SW 1-2 selects DIP SW setting or memory switch setting as initial communication condition. Selected setting
  • Epson TM-L90 | Technical Reference - Page 102
    that the speed of communication between the USB2.0 equipment and the printer is "USB full speed mode." Note: USB2.0 defines three speeds: High speed (480 Mbps), Full speed (12 Mbps) and Low speed (1.5 Mbps). This printer supports only Full speed (12 Mbps) and Low speed (1.5 Mbps). 102 Application
  • Epson TM-L90 | Technical Reference - Page 103
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Chapter 6 ESC/POS Command-Related Information This chapter introduces the printer operation settings that can be made with ESC/POS commands and their precautions. 6.1 TM Printer Operation Performed When Power Switch is Disabled Note: This function
  • Epson TM-L90 | Technical Reference - Page 104
    6.1.2 Power Off Control by the Host You can turn off the power of the TM printer from the application. When using the printer with the power switch disabled (DIP switch 1 on), turn off the printer by command before turning off the host. Power off control differs as follows according to the setting
  • Epson TM-L90 | Technical Reference - Page 105
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 6.3 Control After Paper Cut When command control is used for printing, feed paper more than 1 mm {16/406"} immediately after paper cutting, and then stop feeding. 1 mm {16/406"} is equivalent to about 8 dots. If paper is left unfed after cutting,
  • Epson TM-L90 | Technical Reference - Page 106
    can customize your TM printer by changing memory switches and the command default value and saving the data onto the NV (nonvolatile) memory. Refer to the next section. 6.5.1 Printer Initial Setting Up Printer initial setting up can be made by memory switches and character code page. Refer to page
  • Epson TM-L90 | Technical Reference - Page 107
    Handling TM-L90/TM-L90 Peeler Model Technical Reference Guide 7.1 Maintenance 7.1.1 Cleaning the autocutter (TM-L90 only) If label paper printer from the power connector. 3. Open the roll paper cover. Note: If the roll paper cover will not open, take action in accordance with the troubleshooting
  • Epson TM-L90 | Technical Reference - Page 108
    -based solvents. To do so may dissolve the adhesive and make removing it even more difficult. 5. Insert the roll paper after removing the adhesive. For the method of inserting the roll paper, refer to "Paper Loading Method" on page 55. WARNING: Be sure to remove your finger from inside the roll
  • Epson TM-L90 | Technical Reference - Page 109
    TM-L90/TM-L90 Peeler Model Technical Reference Guide CAUTION: The print head is very hot right after printing and is very dangerous. Be sure to allow the print head to cool down (after printing) before cleaning it. Also, be sure to turn off the printer power before cleaning the print head. Paper
  • Epson TM-L90 | Technical Reference - Page 110
    Cleaning the peeler (TM-L90 Peeler Model only) If label adhesive accumulates on the rollers of the peeler, remove it with the following procedure. 1. Pull the peeler open lever forward, and open the peeler cover. 2. Using a waste label or the like, remove the adhesive by dabbing the label on the
  • Epson TM-L90 | Technical Reference - Page 111
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 7.2 Troubleshooting 7.2.1 Panel LED and Error Status 7.2.1.1 Power (POWER) LED Power (POWER) LED Item LED color On states On Off Flashing with short intervals *1 Flashing with long intervals *1 Specifications Green Power is supplied Power is
  • Epson TM-L90 | Technical Reference - Page 112
    execution status Approx.320 ms Waiting for label removal (TM-L90 Peeler Model only) Approx.320 ms 7.2.1.3 Error (ERROR) LED Error (ERROR) LED Item LED color ON states On Off Blinking Specifications Red / Orange (TM-L90: 4** models) Offline (except during paper feeding using the FEED button and
  • Epson TM-L90 | Technical Reference - Page 113
    TM-L90/TM-L90 Peeler Model Technical Reference Guide your dealer or a Epson service center. Automatically recoverable errors Although normal printer operation is no longer closing the roll paper cover. Recovers automatically when the print head cools. Note: *1 Use the memory switch Msw8-8 to
  • Epson TM-L90 | Technical Reference - Page 114
    , and then reset the paper layout of the current paper in the printer. Note: *1: Use the memory switch Msw8-8 to determine the cover open error as an automatically recoverable error or a recoverable error. (Factory default setting is Recoverable Error.) *2: With the TM-L90, if an autocutter error
  • Epson TM-L90 | Technical Reference - Page 115
    TM-L90/TM-L90 Peeler Model Technical Reference Guide How to send the error recover command from each of the drivers is as follows. ❏ OPOS ADK Either use the ClearOutput method or send the error recover command of ESC/POS to the printer. For more details, see the manual supplied with your OPOS. ❏ APD
  • Epson TM-L90 | Technical Reference - Page 116
    the power back on, contact your dealer or a Epson service center. CAUTION: When an unrecoverable error occurs, turn off the power supply immediately. Unplug the AC cable from the printer when the power switch is invalid. ❏ TM-L90 unrecoverable errors Unrecoverable Errors Error name Type of
  • Epson TM-L90 | Technical Reference - Page 117
    TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ TM-L90 Peeler Model unrecoverable errors Unrecoverable Errors Error name Type of error Error LED flash code Approx.320 ms Recovery measure R/W error in memory After R/W checking, the printer does not work correctly. LED ON LED OFF
  • Epson TM-L90 | Technical Reference - Page 118
    7.2.2 The autocutter is jammed or the roll paper cover will not open (TM-L90 only) 1. Turn off the power. 2. Insert a flathead screwdriver into the groove shown in the figure, and push up the cover. Side view closeup Note: There
  • Epson TM-L90 | Technical Reference - Page 119
    -L90/TM-L90 Peeler Model Technical Reference Guide 7.2.3 When a paper jam occurs (TM-L90 Peeler Model) 1. Turn off the power. 2. Pull the peeler open lever forward, and open the peeler cover. 3. Pull the cover open lever, and open the roll paper cover. 4. Check for a paper jam, and remove the paper
  • Epson TM-L90 | Technical Reference - Page 120
    7.3 Shipping Procedures Perform the following measures before shipping the printer. 1. Turn off the printer. 2. Check that the POWER LED is off. 3. Remove the power supply connectors. 4. Pack the printer, keeping it right-side-up. 120 Handling
  • Epson TM-L90 | Technical Reference - Page 121
    Appendix Appendix TM-L90/TM-L90 Peeler Model Technical Reference Guide Setting items for Memory Switch Setting Mode Setting items of TM-L90 4** models See "Memory Switch Settings" on page 44 for the procedures for the memory switch setting mode. Setting Items 1st page 2nd page 3rd page 1:
  • Epson TM-L90 | Technical Reference - Page 122
    5: Default Character 1: Code Page 1: Western Europe, Southern Europe Page 0: PC437 (USA, Standard Europe) Page 3: PC860 (Portuguese) Page 11: PC851 (Greek) Page 14: PC737 (Greek) Page 15: ISO8859-7 (Greek) Page 16: WPC1252 Page 18: PC852 (Latin 2) Page 19: PC858 Page 34: PC855 (Cyrillic) Page 38:
  • Epson TM-L90 | Technical Reference - Page 123
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 8: USB Interface 1: Class Settings 2: USB Power Saving Vendor Class, Printer Class Enabled, Disabled 9: Printing Speed Level 1 (Slow) - Level 6 - Level 9 (Fast) 10: Auto Cut Enable, Disable 11: Label measurement for paper, Move to
  • Epson TM-L90 | Technical Reference - Page 124
    13: Other Settings 1: Buzzer Control 1: Select Buzzer 2: Buzzer Frequency (Error) Internal Buzzer, Option Buzzer, Buzzer Disable Continuous, 1 time, No sound 3: Sound Pattern (Auto cut) Pattern A, Pattern B, Pattern C, Pattern D, Pattern E 4: Buzzer Frequency (Auto cut) 1 time, No sound 5:
  • Epson TM-L90 | Technical Reference - Page 125
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Setting items of TM-L90 other than 4** models See "Memory Switch Settings" on page 44 for the procedures for the memory switch setting mode. Setting Items 1st page 2nd page 1: Auto Cutter 2: Paper, Print Density 1: Monochrome 2: Two color
  • Epson TM-L90 | Technical Reference - Page 126
    DLE ENQ [Select automatic measurement of maximum length for paper] 160 mm, 300 mm [Select moving to the print starting position when power is turned on] moves to starting position does not move Setting items of TM-L90 Peeler 39* models See "Memory Switch Settings" on page 44 for the procedures for
  • Epson TM-L90 | Technical Reference - Page 127
    TM-L90/TM-L90 Peeler Model Technical Reference Guide 5: Default Character 1: Code Page 1: Western Europe, Southern Europe Vietnam, Arabia 8: USB Interface 1: Class Settings 2: USB Power Saving Vendor Class, Printer Class Enabled, Disabled 9: Printing Speed Level 1 (Slow) - Level 6 - Level
  • Epson TM-L90 | Technical Reference - Page 128
    cover open/close DLE ENQ or press down PAPER FEED button DLE ENQ or Main cover open/close or press down PAPER FEED button Setting items of TM-L90 Peeler other than 39* models See "Memory Switch Settings" on page 44 for the procedures for the memory switch setting mode. Setting Items 1st page 2nd
  • Epson TM-L90 | Technical Reference - Page 129
    Signal 7: Paper Width 8: Other settings 1 9: Other settings 2 11: Select label TM-L90/TM-L90 Peeler Model Technical Reference Guide [Baud PAPER FEED button DLE ENQ or Main cover open/close or press down PAPER FEED button [Select manual feed operation] Paper feed to the print starting position Paper
  • Epson TM-L90 | Technical Reference - Page 130
    Product Specifications TM-L90 Print method Print width Cutting method Cut type Possible thickness to be cut with a manual cutter Character sets Interface (compatible) Buffer D.K.D. function Power Supply Operating Voltage Current consumption 4** models Other than 4** models Thermal line
  • Epson TM-L90 | Technical Reference - Page 131
    Temperature Humidity Weight (mass) TM-L90/TM-L90 Peeler Model Technical Reference Guide Operating: 5 to 45 °C {41 to 113 °F} Storage: -10 to 50 °C {14 to 122 °F} 10 to 90% Approximately 1.9 kg {4.19 lb} Note: Install the paper exit guide packed in the box with the printer when the autocutter is
  • Epson TM-L90 | Technical Reference - Page 132
    TM-L90 Peeler Model 39* models Other than 39* models Print method Thermal line, 8 dots/mm x 8 dots/mm (203 dpi x 203 dpi) Print width 80 mm (factory setting) or 38 to 70 mm can be set using a roll paper spacer Manual cutter specification With continuous issuing, it is possible to cut the
  • Epson TM-L90 | Technical Reference - Page 133
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Print Specifications Item Printing method Dot density Printing direction Paper width Maximum printable area Characters per line Print Speed Carriage return width Specifications Thermal line printing 0.125 mm/dot x 0.125 mm/dot (203 dpi x 203
  • Epson TM-L90 | Technical Reference - Page 134
    TM-L90 Life MTBF MCBF When printing labels When issuing receipts (thickness type) When printing receipts Thermal head Autocutter 1,000,000 labels issued (When the length of the label in the paper on the printer using 15-line feeding and 10-line printing repeatedly with 75 m of paper thickness. The
  • Epson TM-L90 | Technical Reference - Page 135
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Vibration resistance and release it (for all 4 edges). When the printer is not printing, no external or internal damage should when the Epson evaluation printing pattern is used. This value may be different, depending on the paper to be
  • Epson TM-L90 | Technical Reference - Page 136
    TM-L90 Peeler Model Life Labels Receipts MTBF MCBF Thermal head Vibration resistance Impact resistance Acoustic noise (operating) Issues 1,000,000 labels (With feed direction label the printer is Epson evaluation printing pattern is used. This value may be different, depending on the paper
  • Epson TM-L90 | Technical Reference - Page 137
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Character Specifications Character Specifications Item Character type Alphanumeric International Extended graphics JIS (JISX0208-1990) Special font Specifications TM-L90 4** models, TM-L90 Peeler 39* models 95 characters 18 sets 128
  • Epson TM-L90 | Technical Reference - Page 138
    vertical magnification 24 vertical magnification ❏ When the printer is placed in the wait state for data from paper feed of 10 or more lines. (This is because a small piece of cut paper is difficult to eject and may cause a paper jam.) Paper Specifications Refer to "Consumable Specifications
  • Epson TM-L90 | Technical Reference - Page 139
    Printing Area Thermal Paper TM-L90/TM-L90 Peeler Model Technical Reference Guide Printable Area (For Thermal Paper) Note: The printable area may be out of alignment by 2 mm {0.08"} maximum (left or right), due to the paper position or tolerance of parts. Therefore, the print area must be set in
  • Epson TM-L90 | Technical Reference - Page 140
    of the liner. Numeric values used above table are center values in designing. Paper width is only for nominal dimension. The values in parenthesis are the maximum value for the paper tolerance. Continuous Label Roll Paper Allow the left and right margins of 2.8 mm or more outside the printable
  • Epson TM-L90 | Technical Reference - Page 141
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Printing Position in Relation to Cutter Position (TM-L90) The TM-L90 printing position and cutter positions are shown in the following figure. 29 14 Printing Position in Relation to Cutter Position Note: The values in the
  • Epson TM-L90 | Technical Reference - Page 142
    Manual Cutter Position (TM-L90 Peeler Model) The TM-L90 Peeler Model printing position, peeling position and manual cutter positions are shown in the following figure. Printing Position in Relation to Cutter Position Note: The values in the figure above are design center values, and since the paper
  • Epson TM-L90 | Technical Reference - Page 143
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Overview of External Dimensions ❏ Height: ❏ Width: ❏ Depth: ❏ Weight: 203 mm 140 mm 148 mm Approximately 1.9 kg (without roll paper) External view (TM-L90: other than 4** models) External Appearance (TM-L90) [Units: Appendix 143
  • Epson TM-L90 | Technical Reference - Page 144
    External view (TM-L90 Peeler 39* models) [Units: mm] External Appearance (TM-L90 Peeler Model) Note: As the printer is partly made of coated steel-faced plate, the edges of it may rust. However, it doesn't affect performance of the printer. 144 Appendix
  • Epson TM-L90 | Technical Reference - Page 145
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Operating Specifications Item Temperature Humidity When printing During storage When printing During storage Specifications 5 to 45 C {41 to 113 F} -10 to 50 C {14 to 122 F} (except for paper) 10 to 90% RH 10 to 90% RH (except for paper)
  • Epson TM-L90 | Technical Reference - Page 146
    length MARK SPACE Baud rate Parity check Parity selection Stop bit Connector Printer side Specifications Serial Asynchronous Select one of the following using DIP switch 1-3 or the memory switches (switch operation/command (operation). ❏DTR/DSR ❏XON/XOFF -3 V to -15 V logic "1" /Off +3 V to
  • Epson TM-L90 | Technical Reference - Page 147
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Functions of Each memory switch 1-8 setting enables this signal to be used as a reset signal for the printer. The printer is reset when the signal remains SPACE for 1 ms or more.* *: Available only for TM-L90 other than 4** models, TM-L90 Peeler
  • Epson TM-L90 | Technical Reference - Page 148
    recovers from an error using some ESC/POS commands. 5) When the receive buffer becomes full 6) When the printer switches from online to offline Memory Switch 1-3 1(ON) 0(OFF) Transmit Transmit Transmit - Transmit Transmit Transmit Transmit - Transmit Transmit Code The XON/XOFF codes are
  • Epson TM-L90 | Technical Reference - Page 149
    TM-L90/TM-L90 Peeler Model Technical Reference Guide IEEE1284 Parallel Interface Mode The IEEE1284 parallel interface is comprised of the following two modes. Mode Compatibility Mode Reverse Mode Communication direction Host  printer communication Printer  host communication Other information
  • Epson TM-L90 | Technical Reference - Page 150
    Host/Ptr 7 Host/Ptr 8 Host/Ptr 9 Host/Ptr 10 Printer 11 Printer 12 Printer 13 Printer 14 Host 15 16 17 18 Printer 19 20 21 22 23 24 25 26 27 28 29 30 31 Host 32 Printer 33 34 Printer 35 Printer 36 Host *NC: None Connect ND: Not Defined Compatibility Mode
  • Epson TM-L90 | Technical Reference - Page 151
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: A signal name prefixed by "n" indicates an "L" active signal. Bidirectional communications cannot take place unless all signal names for both sides correspond to each other.
  • Epson TM-L90 | Technical Reference - Page 152
    Output electric power (rating): Output peak current: DC 24 V ± 5% 2.0 A 48 VA 4.5 A Case Specifications ❏ Size: ❏ Weight: ❏ Material: ❏ Color: 68 mm (D)  136 mm (L)  32 mm (H) (excluding projections) Refer to figure below. Approx. 0.4 kg (excluding the AC cable) Flame-resistance grade: V0 Black
  • Epson TM-L90 | Technical Reference - Page 153
    TM-L90/TM-L90 Peeler Model Technical Reference Guide AC Cable Selection ❏ Select an AC cable that satisfies the following conditions. • Safety Standard product • Plug with P.E terminal ❏ Ground connection: Ground certainly for safety. Appendix 153
  • Epson TM-L90 | Technical Reference - Page 154
    TM-L90 Peeler Model. 90 mm {3.54"} maximum Receipt roll paper: see "Specified receipt roll paper" on page 155 Die-cut label roll paper: see "Specified die-cut label roll paper" on page 155 Continuous label roll paper: see "Specified continuous label roll paper" on page 155 TM-L90: Thermal paper
  • Epson TM-L90 | Technical Reference - Page 155
    TM-L90/TM-L90 Peeler Model Technical Reference Guide NOTE: ❏ Paper must not be pasted to the roll paper core. ❏ Using roll paper with an inside diameter of 25.4 mm {1"} or less may decrease the detection accuracy of the roll paper near-end sensor. Specified Roll Paper Specified receipt roll paper
  • Epson TM-L90 | Technical Reference - Page 156
    (2) NOTE: Reflecting rates are measured by the Macbeth PCM-II (Filter D) meter. Paper without intervals between labels, such as continuous label paper, paper with perforated lines between labels, and paper with slits between labels, can also be used under the same requirements. Black Mark Interval
  • Epson TM-L90 | Technical Reference - Page 157
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Requirements for Die-Cut Label Paper Die-cut label paper is shown below. Example of transparency label roll paper Features: ❏ Paper layout can be set automatically ("Paper Loading Method" on page 55) ❏ Paper layout can be set manually ("Paper
  • Epson TM-L90 | Technical Reference - Page 158
    from the cutting position to the print starting position (=L3-L4) is 2.75 mm {0.11"} or more. Black mark position for die-cut label paper If die-cut label with black marks is used, there are two reflective rate requirements, depending on the size and position of black marks. Be sure to use
  • Epson TM-L90 | Technical Reference - Page 159
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Black mark position I The black mark positions on the paper to be manufactured must meet the requirements in the figure below. The reflective rates of the black mark portions 1 and label portions 2 must meet the combinations shown in the table
  • Epson TM-L90 | Technical Reference - Page 160
    % 75% 70% More black mark does not exist (2) NOTE: Reflective rates are measured by the Macbeth PCM-II (Filter D) meter. If label paper meets Black Mark Position Requirement I, it is not necessary to consider Black Mark Position Requirement II.  4 - 5.5 *5  0.5 *15 or more   (The dotted
  • Epson TM-L90 | Technical Reference - Page 161
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Transparency rate of die-cut label paper If transparency (without black marks) label is used, use a label that meets the following requirements so that the printer can recognize the label position: (label + backing paper): transparency 18% or less
  • Epson TM-L90 | Technical Reference - Page 162
    used with the printer are shown in the figure below: Die-Cut Label Paper Thickness, Peeling Strength, and Adhesive Agent Peeling strength of the label against backing paper, measured by FINAT FTM-1 (Europe), ASTM D3330/D3330M-02 (U.S.A.). Note: ❏ Total of thermal paper and backing paper: 145 m or
  • Epson TM-L90 | Technical Reference - Page 163
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Size of continuous label paper To prevent the print head from sticking to the adhesive agent, be sure to use continuous label paper that has a cut-off edge. Note: "cut-off edge" is a method of cutting and removing the edge of the label in advance
  • Epson TM-L90 | Technical Reference - Page 164
    Avoid direct light. ❏ Extended exposure to direct light (as with placement of the printer near windows) may cause discoloration or faded printing. ❏ When the printer is not used for one week or more, it is recommended not to leave the thermal paper between the platen and the print head. 164 Appendix
  • Epson TM-L90 | Technical Reference - Page 165
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Character Code Table Page 0 (PC437 : USA, Standard Europe) (International character set : when America is selected) HEX 0 1 2 3 4 5 6 7 0 NUL DLE SP 0 00 16 32 @ P 48 64 ` 80 p
  • Epson TM-L90 | Technical Reference - Page 166
    Page 1 (Katakana) HEX 8 9 A B C D E F 0 ‫ؤ‬ ┴ SP  㩊 㩚 ═ ‫ؖ‬ 128 144 160 176 192 208 224 240 1 ‫إ‬ ┬ 㨫 㨻 㩋 㩛 ╞ ౞ 129 145 161 177 193 209 225 241 2 ‫ا‬ ┤ 㨬 㨼 㩌 㩜 ╪ ᐕ 130 146 162 178 194 210 226 242 3 ‫ئ‬ ├ 㨭 㨽 㩍 㩝 ╡ ᦬ 131 147 163
  • Epson TM-L90 | Technical Reference - Page 167
    Page 2 (PC850: Multilingual) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ ð Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ Ð β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô 130 146 162 178 194 210
  • Epson TM-L90 | Technical Reference - Page 168
    Page 3 (PC860: Portuguese) HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü À í ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é È ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 163 179
  • Epson TM-L90 | Technical Reference - Page 169
    TM-L90/TM-L90 Peeler Model Technical Reference Guide Page 4 (PC863: Canadian-French) HEX 8 9 A B C D E F 0 Ç É ¦ ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü È ´ ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é Ê ó ▓ ┬ ╥ Γ ≥ 130 146 162 178
  • Epson TM-L90 | Technical Reference - Page 170
    Page 5 (PC865: Nordic) HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 163 179 195
  • Epson TM-L90 | Technical Reference - Page 171
    Page 11 (PC851: Greek) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç Ί ϊ ░ └ Τ ζ - 128 144 160 176 192 208 224 240 1 ü SP ΐ ▒ ┴ Υ η ± 129 145 161 177 193 209 225 241 2 é Ό ó ▓ ┬ Ф θ υ 130 146 162 178 194 210 226
  • Epson TM-L90 | Technical Reference - Page 172
    205 221 237 253 E Ä × « ż ╬ Ì · ■ 142 158 174 190 206 222 238 254 F Ĉ ĵ » ┐ ¤ ▀ ´ SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 172 Appendix
  • Epson TM-L90 | Technical Reference - Page 173
    Page 13 (PC857: Turkish) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ o Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ a β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô SP 130 146 162 178 194 210
  • Epson TM-L90 | Technical Reference - Page 174
    205 221 237 253 E О η χ ╛ ╬ ▐ Ό ■ 142 158 174 190 206 222 238 254 F П θ ψ ┐ ╧ ▀ Ύ SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 174 Appendix
  • Epson TM-L90 | Technical Reference - Page 175
    Page 15 (ISO8859-7: Greek) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP SP SP ° ΐ Π ΰ π 128 144 160 176 192 208 224 240 1 SP SP ' ± Α Р α р 129 145 161 177 193 209 225 241 2 SP SP ' ² Β SP β ς
  • Epson TM-L90 | Technical Reference - Page 176
    Page 16 (WPC1252) HEX 8 9 A B C D E F 0 € SP SP ° À Ð à ð 128 144 160 176 192 208 224 240 1 SP ' ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 , ' ¢ ² Â Ò â ò 130 146 162 178 194 210 226 242 3 ƒ " £ ³ Ã Ó ã ó 131 147 163 179 195
  • Epson TM-L90 | Technical Reference - Page 177
    Page 17 (PC866: Cyrillic #2) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 А Р а ░ └ ╨ р Ё 128 144 160 176 192 208 224 240 1 Б С б ▒ ┴ ╤ с ё 129 145 161 177 193 209 225 241 2 В Т в ▓ ┬ ╥ т Є 130 146 162 178 194 210
  • Epson TM-L90 | Technical Reference - Page 178
    Page 18 (PC852: Latin 2) HEX 8 9 A B C D E F 0 Ç É á ░ └ đ Ó - 128 144 160 176 192 208 224 240 1 ü Ĺ í ▒ ┴ Ð β ˝ 129 145 161 177 193 209 225 241 2 é ĺ ó ▓ ┬ Ď Ô ˛ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ Ë Ń ˇ 131 147 163 179
  • Epson TM-L90 | Technical Reference - Page 179
    Page 19 (PC858: Euro) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ ð Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ Ð β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô 130 146 162 178 194 210 226 242
  • Epson TM-L90 | Technical Reference - Page 180
    Page 20 (Thai character code 42) 180 Appendix
  • Epson TM-L90 | Technical Reference - Page 181
    Page 21 (Thai character code 11) TM-L90/TM-L90 Peeler Model Technical Reference Guide Appendix 181
  • Epson TM-L90 | Technical Reference - Page 182
    Page 22 (Thai character code 13) 182 Appendix
  • Epson TM-L90 | Technical Reference - Page 183
    Page 23 (Thai character code 14) TM-L90/TM-L90 Peeler Model Technical Reference Guide Appendix 183
  • Epson TM-L90 | Technical Reference - Page 184
    Page 24 (Thai character code 16) 184 Appendix
  • Epson TM-L90 | Technical Reference - Page 185
    Page 25 (Thai character code 17) TM-L90/TM-L90 Peeler Model Technical Reference Guide Appendix 185
  • Epson TM-L90 | Technical Reference - Page 186
    Page 26 (Thai character code 18) 186 Appendix
  • Epson TM-L90 | Technical Reference - Page 187
    Page 30 (TCVN-3: Vietnamese) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F 8 9 A B C D E F SP SP SP SP SP é 128 144 160 176 192 SP SP 208 224 240 SP SP SP SP SP ẹ ỏ ủ 129 145 161 177
  • Epson TM-L90 | Technical Reference - Page 188
    Ắ Ẻ Ị 142 158 174 190 206 Ợ Ỵ 222 238 254 SP SP SP SP Ẽ 143 159 175 191 Ò 207 Ù 223 SP 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 188 Appendix
  • Epson TM-L90 | Technical Reference - Page 189
    Page 32 (PC720: Arabic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP SP ‫ﺏ‬ ░ └ ╨ 128 144 160 176 192 208 224 240 1 SP ّ ‫ﺓ‬ ▒ ┴ ╤ ‫ﻁ‬ ً 129 145 161 177 193 209 225 241 2 é ْ ‫ﺕ‬ ▓ ┬ ╥ ‫ﻅ‬ ٌ 130 146 162 178 194
  • Epson TM-L90 | Technical Reference - Page 190
    205 221 237 253 E Ä × « Š ╬ ▐ Ņ ■ 142 158 174 190 206 222 238 254 F Å ¤ » ┐ Ž ▀ ' SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 190 Appendix
  • Epson TM-L90 | Technical Reference - Page 191
    Page 34 (PC855: Cyrillic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 ђ љ а ░ └ л Я - 128 144 160 176 192 208 224 240 1 Ђ Љ А ▒ ┴ Л р ы 129 145 161 177 193 209 225 241 2 ѓ њ б ▓ ┬ м Р Ы 130 146 162 178 194 210
  • Epson TM-L90 | Technical Reference - Page 192
    221 237 253 E Ä Pt « ╛ ╬ ▐ ε ■ 142 158 174 190 206 222 238 254 F Å ƒ » ┐ ╧ ▀ ∩ SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 192 Appendix
  • Epson TM-L90 | Technical Reference - Page 193
    Page 36 (PC862: Hebrew) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 ‫א‬ ‫נ‬ á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ‫ב‬ ‫ס‬ í ▒ ┴ ╤ ß ± 129 145 161 177 193 209 225 241 2 ‫ג‬ ‫ע‬ ó ▓ ┬ ╥ Γ ≥ 130 146 162 178
  • Epson TM-L90 | Technical Reference - Page 194
    205 221 237 253 E └ ‫ﻼ‬ ‫ﺡ‬ ‫ﺹ‬ ‫ﺧ‬ × ‫ﻍ‬ ■ 142 158 174 190 206 222 238 254 F ┘ ‫ﺀ‬ ‫ﺥ‬ ‫؟‬ ‫ﺩ‬ ‫ﻉ‬ ‫ﻡ‬ SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 194 Appendix
  • Epson TM-L90 | Technical Reference - Page 195
    Page 38 (PC869: Greek) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP Ί ϊ ░ └ Τ ζ 128 144 160 176 192 208 224 240 1 SP Ϊ ΐ ▒ ┴ Υ η ± 129 145 161 177 193 209 225 241 2 SP Ό ό ▓ ┬ Φ θ υ 130 146 162 178 194
  • Epson TM-L90 | Technical Reference - Page 196
    Í 189 Ý í 205 221 ý 237 253 E ¥ ╬ Ž ž Î Ţ î ţ 142 158 174 190 206 222 238 254 F ┐ ® Ż ż Ď ß  ˙ 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 196 Appendix
  • Epson TM-L90 | Technical Reference - Page 197
    Page 40 (ISO8859-15: Latin 9) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP SP SP ° À Ð à ð 128 144 160 176 192 208 224 240 1 SP SP ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 SP SP ¢ ² Â Ò â ò 130
  • Epson TM-L90 | Technical Reference - Page 198
    221 237 253 E ‫ﺄ‬ × « ‫ﻅ‬ ╬ ‫ﻗ‬ ‫ۀ‬ ■ 142 158 174 190 206 222 238 254 F ‫ﺡ‬ » ┐ SP ▀ ‫ی‬ SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 198 Appendix
  • Epson TM-L90 | Technical Reference - Page 199
    Page 42 (PC1118: Lithuanian) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ ą α ≡ 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ č β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ę Γ ≥ 130 146 162 178 194 210
  • Epson TM-L90 | Technical Reference - Page 200
    205 221 237 253 E О Ю о Š ╬ ▐ ю ■ 142 158 174 190 206 222 238 254 F П Я п ┐ Ž ▀ я SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 200 Appendix
  • Epson TM-L90 | Technical Reference - Page 201
    Page 44 (PC1125: Ukrainian) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 А Р а ░ └ ╨ р Ё 128 144 160 176 192 208 224 240 1 Б С б ▒ ┴ ╤ с ё 129 145 161 177 193 209 225 241 2 В Т в ▓ ┬ ╥ т Ґ 130 146 162 178 194 210
  • Epson TM-L90 | Technical Reference - Page 202
    Í 189 Ý í 205 221 ý 237 253 E Ž ž ®  Î Ţ î ţ 142 158 174 190 206 222 238 254 F Ź ź Ż ż Ď ß  ˙ 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 202 Appendix
  • Epson TM-L90 | Technical Reference - Page 203
    Page 46 (WPC1251: Cyrillic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ђ ђ SP ° А Р а р 128 144 160 176 192 208 224 240 1 Ѓ ' Ў ± Б С б с 129 145 161 177 193 209 225 241 2 , ' ў І В Т в т 130 146 162 178 194 210
  • Epson TM-L90 | Technical Reference - Page 204
    E SP SP ® Ύ Ξ ή ξ ώ 142 158 174 190 206 222 238 254 F SP SP ― Ώ Ο ί ο SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 204 Appendix
  • Epson TM-L90 | Technical Reference - Page 205
    Page 48 (WPC1254: Turkish) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 € SP SP ° À Ğ à ğ 128 144 160 176 192 208 224 240 1 SP ' ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 , ' ¢ ² Â Ò â ò 130 146 162 178 194
  • Epson TM-L90 | Technical Reference - Page 206
    ‫מ‬ SP 142 158 174 190 206 222 238 254 F SP SP ¯ ¿ ֿ SP ‫ן‬ SP 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 206 Appendix
  • Epson TM-L90 | Technical Reference - Page 207
    Page 50 (WPC1256: Arabic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 € ‫گ‬ SP ° ‫ہ‬ ‫ﺫ‬ à ً 128 144 160 176 192 208 224 240 1 ‫پ‬ ' ، ± ‫ء‬ ‫ﺭ‬ ‫ﻝ‬ ٌ 129 145 161 177 193 209 225 241 2 , ' ¢ ² ‫ﺁ‬ ‫ﺯ‬ â ٍ 130 146 162
  • Epson TM-L90 | Technical Reference - Page 208
    205 221 237 253 E ˇ ˛ ® ¾ Ī Ž ī ž 142 158 174 190 206 222 238 254 F ¸ SP Æ æ Ļ ß ļ ˙ 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 208 Appendix
  • Epson TM-L90 | Technical Reference - Page 209
    Page 52 (WPC1258: Vietnamese) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 € SP SP ° À Đ à đ 128 144 160 176 192 208 224 240 1 SP ' ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 , ' ¢ ² Â ̉ 130 146 162 178 194 â ̣
  • Epson TM-L90 | Technical Reference - Page 210
    189 205 221 237 253 E Һ һ ® ң О Ю о ю 142 158 174 190 206 222 238 254 F Џ џ Ү ү П Я п я 143 159 175 191 207 223 239 255 Note: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 210 Appendix
  • Epson TM-L90 | Technical Reference - Page 211
    Page 255 (Blank page) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F 8 9 A B C D E F SP SP SP SP SP SP SP SP 128 144 160 176 192 208 224 240 SP SP SP SP SP SP SP SP
  • Epson TM-L90 | Technical Reference - Page 212
    International Character Set * * * * Note: *: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 212 Appendix
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
Peeler Model
Technical Reference Guide
410019405
Rev. F