Epson TM-L90 Plus with Peeler UB-S01 Users Manual
Epson TM-L90 Plus with Peeler Manual
 |
View all Epson TM-L90 Plus with Peeler manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson TM-L90 Plus with Peeler manual content summary:
- Epson TM-L90 Plus with Peeler | UB-S01 Users Manual - Page 1
Epson Corporation Printed in China User's Manual Standards and Approvals The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the EPSON power supplies and TM series printers used in accordance with the instruction manual, EN 55022 Class A may - Epson TM-L90 Plus with Peeler | UB-S01 Users Manual - Page 2
you feel the connector fit into place. Connector of the UB-S01 Connector of the TM printer 3. Secure the UB-S01 with the two screws. 4. Change the printer DIP switches to match the printer to the new interface. See the printer documentation for information about these settings. Make sure you set the - Epson TM-L90 Plus with Peeler | UB-S01 Users Manual - Page 3
Copyright 1997 Printed in China はじめに 本書は、TM UB-S01 UBS01 UB-S01 注意 : VCCI-A 注意 : UB-S01 UB-S01 1 - Epson TM-L90 Plus with Peeler | UB-S01 Users Manual - Page 4
同梱品 ❏ UB-S01 ❏ 本書 交換手順 1. UB-BOARD 2 UB-BOARD 注意 : UB-BOARD 2 UB-S01 す。UB-S01 UB-S01 TM 3. 2 UB-S01 4 2
-
1 -
2 -
3 -
4
 |
 |
1
User’s Manual
Standards and Approvals
Introduction
This manual describes how to replace the UB-S01 on TM series printers
designed for this board. You must check the printer DIP switches after
replacing the UB-S01.
See the documentation that came with the printer for
information about setting the DIP switches.
About The Symbol In This Manual
CAUTION:
Cautions must be observed to avoid minor injury to yourself or damage
to your equipment.
The following standards are applied only to the interface
boards that are so labeled. (EMC is tested using the EPSON
power supplies and TM series printers.)
Europe:
CE marking
North America:
FCC/ICES-003 Class A
Japan:
VCCI Class A
Oceania:
AS/NZS CISPR22 Class A
CE Marking
These products conform to the following Directive and norms:
Directive 2004/108/EC
EN 55022 Class A
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-11
WARNING
This is a Class A product. In a domestic environment this
product may cause radio interference, in which case the user
may be required to take adequate measures.
The printers in which this board is installed becomes class A
devices.
The connection of a non-shielded printer interface cable to the
board will invalidate the EMC standards of this device.
You are cautioned that changes or modifications not expressly
approved by Seiko Epson Corporation could void your
authority to operate the equipment.
FCC Compliance Statement
For American Users
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual,
may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful
interference, in which case the user will be required
to correct the interference at his own expense.
For Canadian Users
This Class A digital apparatus complies with
Canadian ICES-003.
À l'intention des utilisateurs
canadiens
Cet appareil numérique de la classe A est conforme
à la norme NMB-003 du Canada.
Copyright © 1997 by Seiko Epson Corporation
Printed in China