Epson TM-L90 Plus with Peeler Technical Reference Guide
Epson TM-L90 Plus with Peeler Manual
View all Epson TM-L90 Plus with Peeler manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson TM-L90 Plus with Peeler manual content summary:
- Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 1
Peeler Model Technical Reference Guide 410019405 Rev. F - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 2
- Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 3
TM-L90/TM-L90 Peeler Model Technical Reference Guide Cautions ❏ No part of this document may be reproduced, stored with Seiko Epson Corporation's operating and maintenance instructions. ❏ Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 4
For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. WARNING: You must follow warnings carefully to - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 5
Peeler Model Technical Reference Guide WARNING: ❏ Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire or electric shock. Immediately unplug the equipment. ❏ Only disassemble this product as described in this manual. Do not make - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 6
injury. ❏ To ensure safety, unplug this equipment prior to leaving it unused for an extended period. ❏ Take care not to injure your fingers on the manual cutter • When you remove printed paper • When you perform other operations such as loading/replacing roll paper ❏ Do not open the roll paper cover - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 7
Peeler Model Technical Reference Guide About This Manual Aim of the Manual This manual was created to provide all information necessary for system planning, design, installations and application of the printer for designers and developers of POS systems. Manual Content The manual is made up of - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 8
of Use 6 Modular Connector 6 About This Manual 7 Aim of the Manual 7 Manual Content 7 Related Documentation 7 Chapter 1 Product Setup Setup Flow 23 Installation Procedures 24 Precaution For Installation 24 Instructions for Installation 25 Adjusting Roll Paper Near-End Detection Position - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 9
TM-L90/TM-L90 Peeler Model Technical Reference Guide With the Parallel (IEEE1284) Interface 69 With TM-L90 only 107 Print Head Cleaning 109 Cleaning the peeler (TM-L90 Peeler Model only 110 Troubleshooting 111 Panel LED and Error Status 111 The autocutter is jammed or the roll paper cover will - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 10
138 Paper Specifications 138 Printing Area 139 Printing Position in Relation to Cutter Position (TM-L90 141 Printing Position, Peeling Position, Manual Cutter Position (TM-L90 Peeler Model 142 Overview of External Dimensions 143 Interface And Connectors 146 RS-232 Serial Interface 146 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 11
TM-L90/TM-L90 Peeler Model Technical Reference Guide Page 30 (TCVN-3: Vietnamese 187 Page 31 (TCVN-3: Vietnamese 188 Page 32 (PC720: Arabic 189 Page 33 (WPC775: Baltic Rim 190 Page 34 (PC855: Cyrillic - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 12
12 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 13
4** models and TM-L90 Peeler 39* models may have the build-in-USB. 1.1.2 Accessories TM-L90 ❏ Start Here ❏ Label roll paper ❏ Manual CD ❏ Power switch cover ❏ Control panel label used for horizontal installation ❏ Paper exit guide for horizontal installation ❏ Roll paper spacer Product Overview 13 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 14
model. TM-L90 Peeler Model ❏ Start Here ❏ Label roll paper ❏ Manual CD ❏ Power switch cover ❏ Operation label (an instruction label for the peeler open lever and the cover open lever) ❏ Roll (model: WH-10) ❏ AC adapter PS-180 (PS-180 supports power-saving feature) ❏ Power cables 14 Product Overview - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 15
-L90 Peeler Model Technical Reference Guide 1.2 Name and Description of Each Part 1.2.1 Part Names (TM-L90) Power switch Rocker switch (with a power switch soft cover) or Non-locking push button Cutter cover Perforation to pass the cables through FEED Button Manual cutter Cover open lever Roll - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 16
switch soft cover) or Non-locking push button Power switch Peeler open lever Cover open lever FEED Button Control panel Cutter cover Label peeling sensor Manual cutter Peeler cover Wiring knockout Roll paper cover Part Names of TM-L90 Peeler Model * Refer to page 44 for the DIP switch positions - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 17
TM-L90/TM-L90 Peeler Model Technical Reference Guide 1.2.3 Paper FEED button inside the printer Another FEED button is located under the roll paper cover. Paper FEED button (inside the printer) 1.2.4 Control Panel FEED - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 18
❏ When error recovery with FEED button is enabled by memory switch 8-1, if a paper layout error occurs, pressing FEED button recovers from the error and performs automatic paper layout. When using receipt paper: ❏ Pressing this button once feeds paper by one line. Holding this button down feeds - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 19
TM-L90/TM-L90 Peeler Model Technical Reference Guide 1.2.5 Power Switch Refer to "Printer Part Names" on page 15 for the power switch location. The type of the power switch differs, depending on models - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 20
1.2.6 Power Switch Cover To prevent unintentional contact or improper changes and to improve the appearance, use a power switch cover. When using the power switch cover, to turn on or off the TM printer, press the power switch through the hole in the power switch cover. Attach the cover as shown in - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 21
TM-L90/TM-L90 Peeler Model Technical Reference Guide 1.2.7 Mode Switch (TM-L90 Peeler Model Only) With the TM-L90 Peeler Model, you can select the peeling issuing mode and continuous issuing mode with - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 22
1.2.8 Connectors Remove the bottom of the cover as shown in the illustration below. All cables are connected to the connector panel located on the lower rear side of the printer. The connector panel differs, depending on the models. TM-L90 4** models, TM-L90 Peeler 39* models power supply - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 23
Chapter 2 Setup TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.1 Setup Flow Before using the printer, you need to set various settings to increase the printer's functionality. Configure the printer appropriately depending on the environment. - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 24
2.2 Installation Procedures 2.2.1 Precaution For Installation ❏ TM-L90 • Locate the printer on a flat surface, whichever orientation you choose. • Avoid locations susceptible to dust and other foreign matter. • Avoid resting the printer on the power supply or other cables or other objects. • - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 25
-L90/TM-L90 Peeler Model Technical Reference Guide 2.2.2 Instructions for Installation The TM-L90 can be placed the printer on the wall, see the Wall Hanging Bracket Set Installation Manual provided with the WH-10 for instructions. It is recommended to take some measures so that the printer will - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 26
: To hang the printer on the wall, see the Wall Hanging Bracket Set Installation Manual provided with the WH-10 for instructions. When you use TM-L90 horizontally, peel off the backing sheet of the paper exit guide and attach it as shown below to prevent cut paper from falling inside the printer - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 27
TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.3 Adjusting Roll Paper Near-End Detection Position 2.3.1 With TM-L90 Below are three situations when roll paper N.E. detector adjustment is required. ❏ When changing the way - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 28
3. Loosen the detector adjustment screw using a coin or similar tool. Detector adjustment screw 4. The adjustment position of the roll paper Near-End detector changes depending on the way of installation. In either case (vertical or horizontal), adjust the detector so that its tab comes out from the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 29
TM-L90/TM-L90 Peeler Model Technical Reference Guide 5. To fine tune the amount of remaining paper that is detected by the N.E. detector, move the N.E. detector holder shown in the illustration "N.E. Detector Holder" on - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 30
6. Tighten the detector adjustment screw using a coin or similar tool. 7. Move the N.E. detect lever by hand (finger) to confirm that it moves smoothly. Check that the N.E. detect lever is operating properly. 8. Load the roll paper. 9. Close the roll paper cover. 30 Setup - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 31
TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.3.2 With the TM-L90 Peeler Model In the following 2 cases, it is necessary to adjust the position of the roll paper near end sensor. ❏ When - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 32
4. Using a coin or similar tool, loosen the sensor adjustment screw. sensor adjustment screw 5. Adjust the roll paper near end sensor so that the claw of the roll paper near end sensor projects from the hole near the bottom of the device. (Refer to "Part names and the locations of N.E. detector - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 33
TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: Move the N.E. detector in the direction shown by arrow. Adjustment direction N.E. detector holder Adjustment scale #1 #2 Near end sensor holder Outside diameter of specified thermal - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 34
7. Using a coin or similar tool, tighten the sensor adjustment screw. 8. Push the near end sensor with your finger and check that it moves smoothly. push the near end sensor with your finger and check that it moves smoothly 9. Set the roll paper. 10. Close the roll paper cover. 34 Setup - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 35
TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.4 Connecting AC adapter (PS-180) Be sure to use the PS-180 or the equivalent product as the AC adapter. CAUTION: Be sure to remove - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 36
3. Remove the bottom of the cover as shown in the illustration below. 4. Install the connector of the DC cable onto the DC connector (labeled DC24V). Power supply connector Power Supply Connector Note: The connector panel varies depending on the models. When removing the DC cable connector from the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 37
tip of the blade, it might have deteriorated. Contact the nearest Epson service center if you'd like to do the above change. To disable the guide when performing a full cut in the horizontal installation. (Refer to "Instructions for Installation" on page 25 for instructions on attaching the guide.) - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 38
2.5.2 Setting Procedure 1. Turn off the power. 2. Pull the cover open lever, and open the roll paper cover. 3. Push the body case outward (in the direction of the 2 arrows) and remove the cutter cover. cutter cover 4. Remove the single screw retaining the cutter unit and loosen the screw indicated - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 39
TM-L90/TM-L90 Peeler Model Technical Reference Guide 6. Moving the cutter unit in a lateral direction, shift to the dowel position of the desired cut method. dowels Shift to dowel of desired cut method - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 40
2.6 Setting Roll Paper Width The TM-L90 / TM-L90 Peeler Model uses a roll paper 80 mm wide in the default state. When using a roll paper 38 to 70 mm wide with this printer, attach the roll paper spacer in accordance with the following procedure. Note: If a printer has already been used, the paper - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 41
TM-L90/TM-L90 Peeler Model Technical Reference Guide 4. Push the roll paper spacer until it clicks. Note: Check that the roll paper spacer slides smoothly from side to side. 5. Slide the roll paper - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 42
2.7 DIP Switch Settings The following models have the DIP switches for settings. ❏ TM-L90 other than 4** models ❏ TM-L90 Peeler other than 39* models The DIP switches are located inside the printer as shown the picture below. DIP switch cover Before setting DIP switches, remove the DIP switch cover. - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 43
TM-L90/TM-L90 Peeler Model Technical Reference Guide DIP switch settings (Serial interface model) SW No. Function ON OFF 1 Enable/disable Power Switches power supply On/ Power switch is used to switch. Off - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 44
ESC/POS Command Reference". For details on how to obtain this manual, see "Introduction of Control Methods" on page 85. For usage of the Memory Switch Setting Utility, refer to the user's manual of the utility. For usage of the Memory Switch Setting Mode, see "Memory - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 45
TM-L90/TM-L90 Peeler Model Technical Reference Guide 2.8.1 Memory switches of TM-L90 In the following tables, "✓" shows that the setting can be set by the utility or the setting mode. Msw1 Msw - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 46
condition of the built-in USB is set to the Vendordefined class and the system configuration is set so that the USB driver can support the USB power-saving function. [Msw5-2]: Valid only when the receive buffer capacity is 4K bytes. [Msw5-4]: Valid only for parallel interface Msw7 (only - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 47
TM-L90/TM-L90 Peeler Model Technical Reference Guide Msw8 Msw Function Initial Msw Setting Msw Setting Off On setting utility Mode 8-1 (Reserved) - - Off 8-2 User operation for recovery Send the error Send the error - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 48
Customized values Item NV user memory capacity NV graphics memory capacity Print density Print speed Default character code table*1 Default international character*1 Selection of the interface*1 Number of divisions of thermal head energizing Automatic replacement of Font A*1 Automatic replacement - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 49
TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ Depending on the paper type, it is recommended to set the print density as shown in the table below for the best print quality. Receipt - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 50
communication condition of the built-in USB is set to the Vendordefined class and the system configuration is set so that the USB driver can support the USB power-saving function. [Msw5-2]: Valid only when the receive buffer capacity is 4K bytes. [Msw5-4]: Valid only for parallel interface 50 Setup - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 51
TM-L90/TM-L90 Peeler Model Technical Reference Guide Msw7 (only for 39* models) Msw Function 7-1 (Reserved) to 7-7 7-8 Function when FEED button is pressed Off - Feed to the next print starting position On - Feed to the manual cutting position Initial Msw Setting Msw Setting setting utility - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 52
If [Msw8-2] is OFF, the paper is determined automatically if the printer recovers from the paper layout error. Furthermore, the results of automatic paper determination are overwritten if the settings for paper layout are already saved in the NV memory. The [Msw 8-4] setting influences the amount of - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 53
TM-L90/TM-L90 Peeler Model Technical Reference Guide Customized values Item NV user memory capacity NV graphics memory capacity Print density Print speed Default character code table*1 Default international character*1 Number of divisions - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 54
Serial communication conditions Item Baud rate Parity Flow control Data length Option (underlined: initial setting) 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps None, Odd, Even DTR/DSR, XON/XOFF 7-bits, 8-bits Msw Setting Msw Setting utility Mode ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Note: For models - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 55
out roll paper with little paper remaining and insert new roll paper, aligning the paper with the guide, as shown below. 3. Close the roll paper cover; then cut off the paper with the manual cutter. WARNING: Be careful that your finger is not inside the printer when you close the cover because - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 56
2.9.2 With the TM-L90 Peeler Model With the TM-L90 Peeler, the paper loading method differs depending on whether peeling issuing or continuous issuing is used. They are explained as follows. Paper setting with peeling issuing 1. Pull the peeler open lever forward, and open the peeler cover. 2. Pull - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 57
TM-L90/TM-L90 Peeler Model Technical Reference Guide 7. As shown in the following figure, pull the end of the paper to the bottom of the square hole above the manual cutter (label peeling sensor), and close the roll paper cover. Note: Matching the leading edge of the roll paper with the printed - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 58
Paper setting with continuous issuing 1. Pull the peeler open lever forward, and open the peeler cover. 2. Pull the cover open lever, and open the roll paper cover. 3. If there is roll paper with little paper remaining inside the printer, take it out. 4. Put new roll paper in the printer as shown in - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 59
TM-L90/TM-L90 Peeler Model Technical Reference Guide 6. As shown in the following figure, pull the end of the paper to the bottom of the square hole above the manual cutter (label peeling sensor). Note: Matching the leading edge of the roll paper with the printed marks on the printer ensures that - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 60
When using label paper with black mark, it is necessary to make manual setting of paper layout (set using the Memory Switch Setting Utility or will feed several labels and remember the label paper size. See the instructions below. ❏ TM-L90 setting procedure (Procedure for setting the paper type - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 61
TM-L90/TM-L90 Peeler Model Technical Reference Guide 5. With the roll paper cover open, turn on the power while pressing the FEED button inside the printer. (Keep pressing the FEED button until the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 62
5. For peeling issuing, set the end of the roll paper in the peeler, and for continuous issuing, set it in the ejection path, and close the roll paper cover. The printer feeds several labels and remembers the label paper size. This completes the task. 6. For peeling issuing, after setting the paper, - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 63
TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: L1 and L2 are measured by the printer. See the following sketch for the lengths L1 to L7. Parameters Calculated for Automatic Layout Setting ❏ Manual paper layout setting Manual paper layout setting is to directly enter paper data into the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 64
. 2.9.4 Clearing Paper Layout Setting This printer has a function to reset the paper layout set in the automatic paper layout setting mode or by manual setting to the factory setting. Note: This function may be unavailable depending on when you purchased your printer. You cannot use this function if - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 65
TM-L90/TM-L90 Peeler Model Technical Reference Guide Chapter 3 Connecting to the Host Computer and Options 3.1 Connecting the Cable This printer has 5 types of interface, serial, parallel, USB, Ethernet, and wireless LAN. The - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 66
3.2 Connecting to the Host Computer 3.2.1 With the RS-232C Interface When the TM printer is connected to a host PC with a serial interface, the following connection forms are possible: • Stand alone • Pass-through Connections of available serial cross cables are as follows: The types of cable (Type - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 67
TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: Refer to Chapter 5 for the Windows APD. When using APD in serial connection, read the Note in "EPSON Advanced Printer Driver Support Environment" on page 87 that contains precautions for TrueType font printing. Direct Connection (Stand alone - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 68
Pass-through Connections TM printer is connected to DM-D via serial port and DM-D is connected to the host PC via serial port. The following table shows the application control and cable connection types. Application control TM side control setting Xon/Xoff (except OPOS) Xon/Xoff Not available - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 69
TM-L90/TM-L90 Peeler Model Technical Reference Guide 3.2.2 With the Parallel (IEEE1284) Interface TM printer is connected to the host PC via parallel port mounting parallel interface board (UB-P**). DM-D is connected to - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 70
Connection procedure 1. Press the connector on the end of the interface cable firmly onto the interface connector located on the connector panel. 2. Press down the clips on either side of the connector to lock it in place. 3. For interface cables equipped with a ground line, attach the ground line - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 71
TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: Hooking the USB cable through the a customer display (DM-D), set the DIP switch settings as follows. For details, see the User's Manual packed with your customer display. Note: TM-L90 other than 4** models or TM-L90 Peeler other than - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 72
Item Transmission setting Transmission speed Parity Data word length Selection 19200 bps None 8 bits Before turning on the printer, be sure to turn on the customer display (DM-D). If you reverse the order, the customer display will not be recognized correctly. To satisfy the EMI standard, be sure - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 73
Connection procedure TM-L90/TM-L90 Peeler Model Technical Reference Guide CAUTION: Connecting devices directly to LAN cables that are methods of setting the Ethernet interface, refer to the Technical Reference Guide for the Ethernet interface board. Connecting to the Host Computer and Options 73 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 74
3.3 Connecting to the Drawer CAUTION: Be sure to connect a drawer that meets printer specifications. Connecting a drawer of the wrong specifications may result in damage to both the drawer and the printer. Never connect the telephone line to the drawer kick connector (labeled "DK"). Doing so may - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 75
TM-L90/TM-L90 Peeler Model Technical Reference Guide CAUTION: Since the buzzer drive signal and the cash drawer drive the ESC/POS Command Reference. For details on how to obtain this manual, see "Introduction of Control Methods" on page 85. For detailed information about the driver control, see the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 76
76 Connecting to the Host Computer and Options - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 77
printer while pressing the FEED button. Self-test Briefly press the FEED button. Continuing the self-test Hold down the FEED button. Mode selection guide Press the FEED button once briefly and then hold it down. NV Graphics Information Print Press the FEED button twice briefly and then hold it - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 78
In 1 and 2, the following guidances are printed, the PAPER OUT LED flashes, and instructs the user's operations. 1. Continuing self-test guidance 2. Mode selection guidance 4.1.1 Self-test Mode You can check the following items using the self-test. ❏ Firmware version ❏ - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 79
TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ Memory switch settings Follow the steps below. 1. Close the roll paper cover. 2. Turn on the power while pressing FEED button. Keep pressing the button until - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 80
After information printing, the Mode selection guidance is printed again. 5. To finish, turn off the power, or select "Exit and Reboot Printer". 4.1.3 Memory Switch Setting Mode Use the following procedure to start this mode. 1. Close the roll paper cover. 2. Turn on the power while pressing FEED - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 81
TM-L90/TM-L90 Peeler Model Technical Reference Guide 5. After briefly pressing the FEED button (less than one second) for the number of times shown in the print result, hold down the button for - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 82
Note: Do not use this mode when using OPOS. To do so will cause continuous polling, ending in undesirable results. 4.2 Setting/Checking Modes of TM-L90 other than 4** models, TM-L90 Peeler other than 39* models Besides the ordinary print mode, the printer has the following modes to set or check - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 83
TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ Power-on notification setting ❏ Print density ❏ Setting status for power ON ❏ Paper width setting ❏ Paper type ❏ All types of sensor thresholds ❏ Print speed setting ❏ Dip - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 84
5. Follow the guidance to use the mode. See the "Setting items for Memory Switch Setting Mode" on page 121 for setting items and settings. 4.2.3 Hexadecimal Dump Mode TM printer can print the data transmitted from the host computer in hexadecimal numbers and in their corresponding characters. This - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 85
the on-screen instructions. For customers in other countries, go to the following web site: http://download.epson-biz.com/?service=pos For detailed information about the ESC/POS commands, see the ESC/POS Command Reference. You can view this guide by - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 86
programs in Visual Basic and Visual C++ to use Status API can be installed. Manuals The following manuals can be installed. ❏ With TM-L90 • Driver: User's Manual • Status API: Reference Manual ❏ With the TM-L90 Peeler Model • User's Guide (Developer's Guide) 86 Application Development Information - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 87
Guide 5.1.1.3 EPSON Advanced Printer Driver Support Environment Supported interfaces • Serial, Parallel, USB, Ethernet, Wireless LAN Supported OSs (with confirmation of system operation) For details on the supported Manual of APD. The other interfaces (parallel, USB, Ethernet) do not pose problems - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 88
the man-hours for the application development since it includes the following functions that application developers have to consider. The functions are: Support with the Epson-original Direct IO with a parameter, the power-on notification, and off-line buffer clear processing. Note: For detailed - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 89
, etc. can be installed. ❏ Manuals • User's Guide (Environment construction manual: Installation/uninstallation, various utility using methods) • Application Development Guide (Manual for OPOS-compliant application developer: Common manual, Each device manual) Application Development Information 89 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 90
Support Environment Supported interfaces • Serial, Parallel, USB, Ethernet, Wireless LAN Supported OSs (with confirmation of system operation) For details on the supported ESC/POS Command Reference. For details on how to obtain this manual, see "Introduction of Control Methods" on page 85. Note: The - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 91
go to the following web site: http://www.epsonexpert.com/ and follow the on-screen instructions. For customers in other countries, go to the following web site: http://download.epson-biz.com/?service=pos 5.1.4.1 Address Setup Utility for Ethernet Interface (for UB-E**) The utility, which sets an IP - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 92
Note: The detecting the near-end status of the sensor does not necessarily indicate the complete end of the roll paper. Use the sensor as an indication of replacing a roll paper. 5.2.1.2 Roll Paper End Sensor The roll paper end sensor is located in the paper path. It detects the presence of paper - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 93
TM-L90/TM-L90 Peeler Model Technical Reference Guide • During the self test. • When the roll paper cover is open. • During paper feeding using the FEED button. • When the printer stops printing due to a - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 94
5.2.2.4 Receive buffer The capacity of the receive buffer is set using memory switch setting mode or memory switch Msw1-2. The definition of a receive buffer full is described in the following table. The printer ignores the data received when the remaining space in the receive buffer is 0 bytes. - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 95
TM-L90/TM-L90 Peeler Model Technical Reference Guide QRCode Composite Symbology* DataMatrix* *: Available only for TM-L90 4** models or TM-L90 Peeler 39* models Refer to each document of OPOS, Printer Driver or - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 96
Printable characters for code set A characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code NUL 00 0 ( 28 40 P 50 80 SOH 01 1 ) 29 41 Q 51 81 STX - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 97
TM-L90/TM-L90 Peeler Model Technical Reference Guide Printable characters for code set B characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 98
Printable characters for code set C characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code characters Transmission data Hexadecimal Decimal code code 00 00 0 40 28 40 80 50 80 01 01 1 41 29 41 81 51 81 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 99
TM-L90/TM-L90 Peeler Model Technical Reference Guide 5.5 Precautions for Two-Dimensional Code Printing This printer can print two-dimensional codes. The following two-dimensional codes can be printed. ❏ PDF417 ❏ QRCode ❏ MaxiCode ❏ Composite - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 100
with "Q" and their replies with "A" 1. Look through sentences beginning with "Q" to find information relating to your question or problem. 2. Then follow the instructions described in the "A" sentence below it. Q: Print data dropout occurs. A: Check the handshake process. Data dropout can occur - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 101
TM-L90/TM-L90 Peeler Model Technical Reference Guide 2. Confirm DIP SW 1-2. Printer serial communication condition can be set by DIP SW and memory switch. When the printer is powered on, DIP SW 1-2 selects - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 102
printer is "USB full speed mode." Note: USB2.0 defines three speeds: High speed (480 Mbps), Full speed (12 Mbps) and Low speed (1.5 Mbps). This printer supports only Full speed (12 Mbps) and Low speed (1.5 Mbps). 102 Application Development Information - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 103
TM-L90/TM-L90 Peeler Model Technical Reference Guide Chapter 6 ESC/POS Command-Related Information This chapter introduces the printer operation settings that can be made with ESC/POS commands and their precautions. 6.1 TM - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 104
6.1.1 Power Switch-Related User Operation List Power switch enabled When you want to Press the power switch more than 1 power on the TM printer second. When you want to Press the power switch more than 3 power off the TM printer seconds. When there is a power outage When the power outage is - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 105
TM-L90/TM-L90 Peeler Model Technical Reference Guide 6.3 Control After Paper Cut When command control is used for printing, feed paper more than 1 mm {16/406"} immediately after paper cutting, and then stop - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 106
Status There are three ways to get the printer status, and each method has the following features. Refer to the ESC/POS Application Guide for details. • Automatic status (ASB): When processed as a normal command, the printer automatically transmits a status message whenever the status changes. It is - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 107
Handling TM-L90/TM-L90 Peeler Model Technical Reference Guide 7.1 Maintenance 7.1.1 Cleaning the autocutter (TM-L90 If the roll paper cover will not open, take action in accordance with the troubleshooting of the autocutter (page 118). 4. As shown below, remove the adhesive residues accumulated - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 108
Adhesive being removed with flat-blade screwdriver WARNING: Do not touch the area beyond the cutter blade edge. To do so may lead to injury to your fingers. Note: Remove the accumulated adhesive behind the edge of the cutter blade. It is not necessary to polish it to a mirror finish. It is - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 109
7.1.2 Print Head Cleaning TM-L90/TM-L90 Peeler Model Technical Reference Guide CAUTION: The print head is very hot right after printing and is very dangerous. Be sure to allow the print head to cool down (after - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 110
7.1.3 Cleaning the peeler (TM-L90 Peeler Model only) If label adhesive accumulates on the rollers of the peeler, remove it with the following procedure. 1. Pull the peeler open lever forward, and open the peeler cover. 2. Using a waste label or the like, remove the adhesive by dabbing the label on - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 111
TM-L90/TM-L90 Peeler Model Technical Reference Guide 7.2 Troubleshooting 7.2.1 Panel LED and Error Status 7.2.1.1 Power (POWER) LED Power (POWER) LED Item LED color On states On Off Flashing with short intervals *1 Flashing with long - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 112
7.2.1.2 No Roll Paper (PAPER OUT) LED Item LED color ON states On Off Blinking Specifications Red / Orange (TM-L90: 4** models) Roll paper near end (only small amount of paper left on roll) or paper end (no paper left) detected Plenty of paper left on roll TM-L90: TM-L90 Peeler Model: Waiting - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 113
TM-L90/TM-L90 Peeler Model Technical Reference Guide 7.2.1.4 Error Code There are three types of error possible: even after turning the power back on, contact your dealer or a Epson service center. Automatically recoverable errors Although normal printer operation is no longer possible when - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 114
Recoverable errors Although normal printer operation is no longer possible when recoverable errors occur, they do not represent printer failure. You can recover from a recoverable error by turning on the power switch or issuing a command from the driver after eliminating the cause. Recoverable - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 115
Guide How to send the error recover command from each of the drivers is as follows. ❏ OPOS ADK Either use the ClearOutput method or send the error recover command of ESC/POS to the printer. For more details, see the manual font. For more details, see the manual supplied with your APD and the ESC/POS - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 116
. The printer may be out of order. If the same error occurs again even after turning the power back on, contact your dealer or a Epson service center. CAUTION: When an unrecoverable error occurs, turn off the power supply immediately. Unplug the AC cable from the printer when the power switch is - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 117
TM-L90/TM-L90 Peeler Model Technical Reference Guide ❏ TM-L90 Peeler Model unrecoverable errors Unrecoverable Errors Error name Type of error Error LED flash code Approx.320 ms Recovery measure R/W error in memory - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 118
7.2.2 The autocutter is jammed or the roll paper cover will not open (TM-L90 only) 1. Turn off the power. 2. Insert a flathead screwdriver into the groove shown in the figure, and push up the cover. Side view closeup Note: There is also a similar slot on the opposite side face. You can easily - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 119
TM-L90/TM-L90 Peeler Model Technical Reference Guide 7.2.3 When a paper jam occurs (TM-L90 Peeler Model) 1. Turn off the power. 2. Pull the peeler open lever forward, and open the peeler cover. 3. Pull the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 120
7.3 Shipping Procedures Perform the following measures before shipping the printer. 1. Turn off the printer. 2. Check that the POWER LED is off. 3. Remove the power supply connectors. 4. Pack the printer, keeping it right-side-up. 120 Handling - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 121
Appendix Appendix TM-L90/TM-L90 Peeler Model Technical Reference Guide Setting items for Memory Switch Setting Mode Setting items of TM-L90 4** models See "Memory Switch Settings" on page 44 for the procedures for the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 122
5: Default Character 1: Code Page 1: Western Europe, Southern Europe Page 0: PC437 (USA, Standard Europe) Page 3: PC860 (Portuguese) Page 11: PC851 (Greek) Page 14: PC737 (Greek) Page 15: ISO8859-7 (Greek) Page 16: WPC1252 Page 18: PC852 (Latin 2) Page 19: PC858 Page 34: PC855 (Cyrillic) Page 38: - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 123
TM-L90/TM-L90 Peeler Model Technical Reference Guide 8: USB Interface 1: Class Settings 2: USB Power Saving Vendor Class, Printer Class Enabled, Disabled 9: Printing Speed Level 1 (Slow) - Level 6 - Level 9 (Fast) 10: Auto Cut Enable, Disable - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 124
13: Other Settings 1: Buzzer Control 1: Select Buzzer 2: Buzzer Frequency (Error) Internal Buzzer, Option Buzzer, Buzzer Disable Continuous, 1 time, No sound 3: Sound Pattern (Auto cut) Pattern A, Pattern B, Pattern C, Pattern D, Pattern E 4: Buzzer Frequency (Auto cut) 1 time, No sound 5: - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 125
TM-L90/TM-L90 Peeler Model Technical Reference Guide Setting items of TM-L90 other than 4** models See "Memory Switch Settings" on page 44 for the procedures for the memory switch setting mode. Setting - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 126
8: Other settings 11: Select label [Selection of the PAPER OUT LED status when a paper near-end is detected] On, Off [Recovery selection when paper layout error occurs] DLE ENQ or cover open/close DLE ENQ [Select automatic measurement of maximum length for paper] 160 mm, 300 mm [Select moving to - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 127
TM-L90/TM-L90 Peeler Model Technical Reference Guide 5: Default Character 1: Code Page 1: Western Europe, Southern Europe Page 0: PC437 (USA, Standard Europe) Page 3: PC860 (Portuguese) Page 11: PC851 (Greek) Page 14: PC737 (Greek) Page - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 128
13: Other Settings 1: Automatic measurement of maximum length 160 mm, 300 mm 2: Moving to the print start position Disabled, Enabled 5: Select manual feed operation in Paper feed to the print starting position, Paper feed to the Continuous issue mode peel position 2: Interface Settings - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 129
9: Other settings 2 11: Select label TM-L90/TM-L90 Peeler Model Technical Reference Guide [Baud rate set up] 2400 bps, 4800 bps, 9600 bps, 19200 bps, ENQ or Main cover open/close or press down PAPER FEED button [Select manual feed operation] Paper feed to the print starting position Paper feed to - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 130
Product Specifications TM-L90 Print method Print width Cutting method Cut type Possible thickness to be cut with a manual cutter Character sets Interface (compatible) Buffer D.K.D. function Power Supply Operating Voltage Current consumption 4** models Other than 4** models Thermal - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 131
exit guide does not have to be used. Refer to "Instructions for Installation" on page 25 for information on how to attach the paper exit guide. Partial bond adhesion. The manual cutter in the autocutter unit is used to cut the receipt (paper thickness: approximately 75 mm) manually. The cutting type - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 132
) or 38 to 70 mm can be set using a roll paper spacer Manual cutter specification With continuous issuing, it is possible to cut the paper by hand Possible thickness to be 100 m or less cut with the manual cutter Character sets 95 alphanumeric, 18 international character sets, Extended - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 133
-L90/TM-L90 Peeler Model Technical Reference Guide Print Specifications Item Printing method Dot density barcode, two-dimensional code printing> 90 mm/s {2.76"} maximum (only supported with APD) 120 mm/s {3.54"} maximum (*: available only for 4** models) 3.75 mm {0. - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 134
Reliability TM-L90 Life MTBF MCBF When printing labels When issuing receipts (thickness type) When printing receipts Thermal head Autocutter 1,000,000 labels issued (When the length of the label in the paper feeding direction is 25.4 mm {1"} through 63.5 mm {2.5"}. The value above corresponds to - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 135
TM-L90/TM-L90 Peeler Model Technical Reference Guide Vibration resistance Impact resistance Acoustic noise (operating) When packed: Frequency: 5 to 55 Hz Acceleration: Approximately 19.6 m/s2 {2 G} Sweep: 10 minutes (half cycle) Duration: 1 hour Directions: x, y, - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 136
TM-L90 Peeler Model Life Labels Receipts MTBF MCBF Thermal head Vibration resistance Impact resistance Acoustic noise (operating) Issues 1,000,000 labels (With feed direction label length of 25.4 {1 inch} to 63.5 mm {2.5 inch}. Equivalent to a travel distance of about 30 to 70 km. When - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 137
TM-L90/TM-L90 Peeler Model Technical Reference Guide Character Specifications Character Specifications Item Character type Alphanumeric International Extended graphics JIS (JISX0208-1990) Special font Specifications TM-L90 4** models, TM-L90 Peeler 39* models - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 138
Paper Feed Specifications Item Paper feed method Paper feed direction Specifications Friction feed Single-direction Precautions for Printing and Paper Feed ❏ Being a line printer, this printer always feeds paper to print. Therefore, when the line spacing of a single line is set to less than that - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 139
Printing Area Thermal Paper TM-L90/TM-L90 Peeler Model Technical Reference Guide Printable Area (For Thermal Paper) Note: The printable area may be out of alignment by 2 mm {0.08"} maximum (left or right), due to the paper - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 140
Die Cut Label Allow 2.8 mm or more from the left and right edges, and 1.5 mm or more from the top and bottom edges for the printable area. Liner width Label (face stock) 1.5 or more Printable area 2.8 or more 2.8 or more 1.5 or more [Units: mm] Printable Area (for die cut label) Note: If the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 141
TM-L90/TM-L90 Peeler Model Technical Reference Guide Printing Position in Relation to Cutter Position (TM-L90) The TM-L90 printing position and cutter positions are shown in the following figure. 29 14 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 142
TM-L90 Peeler Model) The TM-L90 Peeler Model printing position, peeling position and manual cutter positions are shown in the following figure. Printing Position in Relation to Cutter Position or irregular, allow a sufficient margin when setting the cutting position of the manual cutter. 142 Appendix - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 143
TM-L90/TM-L90 Peeler Model Technical Reference Guide Overview of External Dimensions ❏ Height: ❏ Width: ❏ Depth: ❏ Weight: 203 mm 140 mm 148 mm Approximately 1.9 kg (without roll paper) External view (TM-L90: other than 4** models) External Appearance (TM-L90) [Units: Appendix 143 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 144
External view (TM-L90 Peeler 39* models) [Units: mm] External Appearance (TM-L90 Peeler Model) Note: As the printer is partly made of coated steel-faced plate, the edges of it may rust. However, it doesn't affect performance of the printer. 144 Appendix - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 145
TM-L90/TM-L90 Peeler Model Technical Reference Guide Operating Specifications Item Temperature Humidity When printing During storage When printing During storage Specifications 5 to 45 C {41 to 113 F} -10 to 50 C {14 to 122 F} ( - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 146
Interface And Connectors RS-232 Serial Interface Interface Board Specifications (RS-232 standard) Item Data transfer method Synchronization Handshake Signal level Bit length MARK SPACE Baud rate Parity check Parity selection Stop bit Connector Printer side Specifications Serial - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 147
TM-L90/TM-L90 Peeler Model Technical Reference Guide Functions of Each Connector Pin Pin no. 1 2 3 4 6 7 20 25 Signal name FG TXD RXD RTS DSR Signal direction Output Input Output Input SG - DTR Output - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 148
XON/XOFF When XON/XOFF control is selected, the printer transmits XON or XOFF signals as follows. Transmit timing differs depending on the memory switch 1-3 setting. Signal Printer status XON XOFF 1) When the printer goes online after turning on the power (or reset using interface) 2) When the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 149
TM-L90/TM-L90 Peeler Model Technical Reference Guide IEEE1284 Parallel Interface Mode The IEEE1284 parallel interface is comprised of the following two modes. Mode Compatibility Mode Reverse Mode Communication direction Host printer communication - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 150
Interface Signals Connector Pin Assignment Pin Source 1 Host 2 Host/Ptr 3 Host/Ptr 4 Host/Ptr 5 Host/Ptr 6 Host/Ptr 7 Host/Ptr 8 Host/Ptr 9 Host/Ptr 10 Printer 11 Printer 12 Printer 13 Printer 14 Host 15 16 17 18 Printer 19 20 21 22 23 24 25 26 27 28 29 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 151
TM-L90/TM-L90 Peeler Model Technical Reference Guide Note: A signal name prefixed by "n" indicates an "L" active signal. Bidirectional communications cannot take place unless all signal names for both sides correspond to each other. - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 152
Option Specifications This appendix describes the optional power supply (PS-180). PS-180 Electrical Characteristics ❏ Input conditions Input voltage (rating): Frequency (rating): Power consumption (rating): AC switch LED ❏ Output conditions AC 90 V to AC 264 V (AC 100 V -10% to AC 230 V +15%) 50 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 153
TM-L90/TM-L90 Peeler Model Technical Reference Guide AC Cable Selection ❏ Select an AC cable that satisfies the following conditions. • Safety Standard product • Plug with P.E terminal ❏ Ground connection: Ground certainly for safety. Appendix 153 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 154
Consumable Specifications Paper Specification Paper type Form Size Paper width Paper thickness Roll paper width Roll paper core Roll paper diameter Specified roll paper type Specified original paper type Thermal paper • Receipt paper (without black marks) • Receipt paper (with black marks) • - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 155
TM-L90/TM-L90 Peeler Model Technical Reference Guide NOTE: ❏ Paper must not be pasted to the roll paper core. ❏ Using roll paper with an inside diameter of 25.4 mm {1"} or less may decrease - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 156
Requirements for Receipt Paper Black mark position for receipt paper When manufacturing receipt paper with black marks, be sure to make paper that meets the following requirements. The reflecting rates of black mark portions (1) and non black mark portions (2) must meet the combinations shown in the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 157
Peeler Model Technical Reference Guide Requirements for Die-Cut Label Paper Die-cut label paper is shown below. Example of transparency label roll paper Features: ❏ Paper layout can be set automatically ("Paper Loading Method" on page 55) ❏ Paper layout can be set manually ("Paper Loading Method - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 158
Die-cut label size When manufacturing die-cut label paper, be sure that the paper meets the following requirements. 25.4~279.4 Label length + L2 L2 = 3 ~ 10 Label Size Requirement Note: ❏ Be sure to set the cutting position (L4) between labels. ❏ Be sure that the distance from the cutting - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 159
TM-L90/TM-L90 Peeler Model Technical Reference Guide Black mark position I The black mark positions on the paper to be manufactured must meet the requirements in the figure below. The reflective rates of - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 160
Black mark position II The black mark positions on the paper to be manufactured must meet the requirements in the figure below (the reflective rate is measured using the back of the paper, the non-printing side): ❏ Black mark length in vertical: 4 ~ 5.5 mm {0.157~ 0.217"} ❏ Black mark position: Any - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 161
TM-L90/TM-L90 Peeler Model Technical Reference Guide Transparency rate of die-cut label paper If transparency (without black marks) label is used, use a label that meets the following requirements so that the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 162
Other requirements Requirements for the thickness of the die-cut label paper, peeling strength against backing paper, and the adhesive agent that can be used with the printer are shown in the figure below: Die-Cut Label Paper Thickness, Peeling Strength, and Adhesive Agent Peeling strength of the - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 163
TM-L90/TM-L90 Peeler Model Technical Reference Guide Size of continuous label paper To prevent the print head from sticking to the adhesive agent, be sure to use continuous label paper that has a - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 164
Notes on Paper Handling Thermal paper handling Substances such as chemicals on thermal paper may cause color development or faded printing; therefore, pay attention to the following: ❏ Use water paste, starch paste, polyvinyl paste, or CMC paste when gluing thermal paper. ❏ Volatile organic solvents - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 165
TM-L90/TM-L90 Peeler Model Technical Reference Guide Character Code Table Page 0 (PC437 : USA, Standard Europe) (International character set : when America is selected) HEX 0 1 2 3 4 5 6 7 0 NUL DLE SP 0 00 16 32 @ P 48 64 ` 80 p - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 166
Page 1 (Katakana) HEX 8 9 A B C D E F 0 ؤ ┴ SP 㩊 㩚 ═ ؖ 128 144 160 176 192 208 224 240 1 إ ┬ 㨫 㨻 㩋 㩛 ╞ 129 145 161 177 193 209 225 241 2 ا ┤ 㨬 㨼 㩌 㩜 ╪ ᐕ 130 146 162 178 194 210 226 242 3 ئ ├ 㨭 㨽 㩍 㩝 ╡ 131 147 163 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 167
Page 2 (PC850: Multilingual) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ ð Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ Ð β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô 130 146 162 178 194 210 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 168
Page 3 (PC860: Portuguese) HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü À í ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é È ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 163 179 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 169
TM-L90/TM-L90 Peeler Model Technical Reference Guide Page 4 (PC863: Canadian-French) HEX 8 9 A B C D E F 0 Ç É ¦ ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü È ´ ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é Ê ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 170
Page 5 (PC865: Nordic) HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ ╤ β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 163 179 195 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 171
Page 11 (PC851: Greek) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç Ί ϊ ░ └ Τ ζ - 128 144 160 176 192 208 224 240 1 ü SP ΐ ▒ ┴ Υ η ± 129 145 161 177 193 209 225 241 2 é Ό ó ▓ ┬ Ф θ υ 130 146 162 178 194 210 226 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 172
Page 12 (PC853: Turkish) HEX 8 9 A B C D E F 0 Ç É á ░ └ SP Ó - 128 144 160 176 192 208 224 240 1 ü ċ í ▒ ┴ SP β SP 129 145 161 177 193 209 225 241 2 é Ċ ó ▓ ┬ Ê Ô ℓ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ Ë Ò ʼn 131 147 163 179 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 173
Page 13 (PC857: Turkish) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ o Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ a β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô SP 130 146 162 178 194 210 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 174
Page 14 (PC737: Greek) HEX 8 9 A B C D E F 0 А Р ι ░ └ ╨ ω Ώ 128 144 160 176 192 208 224 240 1 В Σ κ ▒ ┴ ╤ ά ± 129 145 161 177 193 209 225 241 2 Г Т λ ▓ ┬ ╥ έ ≥ 130 146 162 178 194 210 226 242 3 Δ Υ μ │ ├ ╙ ή ≤ 131 147 163 179 195 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 175
Page 15 (ISO8859-7: Greek) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP SP SP ° ΐ Π ΰ π 128 144 160 176 192 208 224 240 1 SP SP ' ± Α Р α р 129 145 161 177 193 209 225 241 2 SP SP ' ² Β SP β ς - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 176
Page 16 (WPC1252) HEX 8 9 A B C D E F 0 € SP SP ° À Ð à ð 128 144 160 176 192 208 224 240 1 SP ' ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 , ' ¢ ² Â Ò â ò 130 146 162 178 194 210 226 242 3 ƒ " £ ³ Ã Ó ã ó 131 147 163 179 195 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 177
Page 17 (PC866: Cyrillic #2) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 А Р а ░ └ ╨ р Ё 128 144 160 176 192 208 224 240 1 Б С б ▒ ┴ ╤ с ё 129 145 161 177 193 209 225 241 2 В Т в ▓ ┬ ╥ т Є 130 146 162 178 194 210 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 178
Page 18 (PC852: Latin 2) HEX 8 9 A B C D E F 0 Ç É á ░ └ đ Ó - 128 144 160 176 192 208 224 240 1 ü Ĺ í ▒ ┴ Ð β ˝ 129 145 161 177 193 209 225 241 2 é ĺ ó ▓ ┬ Ď Ô ˛ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ Ë Ń ˇ 131 147 163 179 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 179
Page 19 (PC858: Euro) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ ð Ó - 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ Ð β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ Ê Ô 130 146 162 178 194 210 226 242 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 180
Page 20 (Thai character code 42) 180 Appendix - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 181
Page 21 (Thai character code 11) TM-L90/TM-L90 Peeler Model Technical Reference Guide Appendix 181 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 182
Page 22 (Thai character code 13) 182 Appendix - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 183
Page 23 (Thai character code 14) TM-L90/TM-L90 Peeler Model Technical Reference Guide Appendix 183 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 184
Page 24 (Thai character code 16) 184 Appendix - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 185
Page 25 (Thai character code 17) TM-L90/TM-L90 Peeler Model Technical Reference Guide Appendix 185 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 186
Page 26 (Thai character code 18) 186 Appendix - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 187
Page 30 (TCVN-3: Vietnamese) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F 8 9 A B C D E F SP SP SP SP SP é 128 144 160 176 192 SP SP 208 224 240 SP SP SP SP SP ẹ ỏ ủ 129 145 161 177 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 188
Page 31 (TCVN-3: Vietnamese) HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F 8 9 A B C D E F SP SP SP SP SP É 128 144 160 176 192 SP SP 208 224 240 SP SP Ă SP SP Ẹ Ỏ Ủ 129 145 161 177 193 209 225 241 SP SP Â SP SP Ê ̀ Õ Ũ 130 146 162 178 194 210 226 242 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 189
Page 32 (PC720: Arabic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP SP ﺏ ░ └ ╨ 128 144 160 176 192 208 224 240 1 SP ّ ﺓ ▒ ┴ ╤ ﻁ ً 129 145 161 177 193 209 225 241 2 é ْ ﺕ ▓ ┬ ╥ ﻅ ٌ 130 146 162 178 194 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 190
Page 33 (WPC775: Baltic Rim) HEX 8 9 A B C D E F 0 Ć É Ā ░ └ ą Ó - 128 144 160 176 192 208 224 240 1 ü æ Ī ▒ ┴ č ß ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ę Ō " 130 146 162 178 194 210 226 242 3 ā ō Ż │ ├ ė Ń ¾ 131 147 163 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 191
Page 34 (PC855: Cyrillic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 ђ љ а ░ └ л Я - 128 144 160 176 192 208 224 240 1 Ђ Љ А ▒ ┴ Л р ы 129 145 161 177 193 209 225 241 2 ѓ њ б ▓ ┬ м Р Ы 130 146 162 178 194 210 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 192
Page 35 (PC861: Icelandic) HEX 8 9 A B C D E F 0 Ç É á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ ╤ ß ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 194 210 226 242 3 â ô ú │ ├ ╙ π ≤ 131 147 163 179 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 193
Page 36 (PC862: Hebrew) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 א נ á ░ └ ╨ α ≡ 128 144 160 176 192 208 224 240 1 ב ס í ▒ ┴ ╤ ß ± 129 145 161 177 193 209 225 241 2 ג ע ó ▓ ┬ ╥ Γ ≥ 130 146 162 178 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 194
Page 37 (PC864: Arabic) HEX 8 9 A B C D E F 0 ° β SP ٠ ¢ ﺫ ـ ? 128 144 160 176 192 208 224 240 1 · ∞ 129 145 ١ 161 ﺀ 177 ﺭ ﻓ 193 209 ? 225 241 2 · φ ﺂ ٢ ﺁ ﺯ ﻗ ﻥ 130 146 162 178 194 210 226 242 3 √ ± £ ٣ ﺃ ﺳ ﻛ ﻩ - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 195
Page 38 (PC869: Greek) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP Ί ϊ ░ └ Τ ζ 128 144 160 176 192 208 224 240 1 SP Ϊ ΐ ▒ ┴ Υ η ± 129 145 161 177 193 209 225 241 2 SP Ό ό ▓ ┬ Φ θ υ 130 146 162 178 194 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 196
Page 39 (ISO8859-2: Latin 2) HEX 8 9 A B C D E F 0 ░ └ SP ° Ŕ Ð ŕ đ 128 144 160 176 192 208 224 240 1 ▒ ┴ Ą ą Á Ń á ń 129 145 161 177 193 209 225 241 2 ▓ ┬ ˘ ˛ Â Ň â ň 130 146 162 178 194 210 226 242 3 │ ├ Ł ł Ă Ó ă ó 131 147 163 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 197
Page 40 (ISO8859-15: Latin 9) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 SP SP SP ° À Ð à ð 128 144 160 176 192 208 224 240 1 SP SP ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 SP SP ¢ ² Â Ò â ò 130 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 198
Page 41 (PC1098: Farsi) HEX 8 9 A B C D E F 0 SP ﺅ ﺣ ░ └ ﻊ ک 128 144 160 176 192 208 224 240 1 SP ﺋ ﺥ ▒ ┴ ﻋ ﻛ ﯽ 129 145 161 177 193 209 225 241 2 ، ﺏ ﺧ ▓ ┬ ﻌ گ ﻳ 130 146 162 178 194 210 226 242 3 ؛ ﺑ ﺩ │ ├ - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 199
Page 42 (PC1118: Lithuanian) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ç É á ░ └ ą α ≡ 128 144 160 176 192 208 224 240 1 ü æ í ▒ ┴ č β ± 129 145 161 177 193 209 225 241 2 é Æ ó ▓ ┬ ę Γ ≥ 130 146 162 178 194 210 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 200
Page 43 (PC1119: Lithuanian) HEX 8 9 A B C D E F 0 А Р а ░ └ ą р Ё 128 144 160 176 192 208 224 240 1 Б С б ▒ ┴ č с ё 129 145 161 177 193 209 225 241 2 В Т в ▓ ┬ ę т ≥ 130 146 162 178 194 210 226 242 3 Г У г │ ├ ė у ≤ 131 147 163 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 201
Page 44 (PC1125: Ukrainian) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 А Р а ░ └ ╨ р Ё 128 144 160 176 192 208 224 240 1 Б С б ▒ ┴ ╤ с ё 129 145 161 177 193 209 225 241 2 В Т в ▓ ┬ ╥ т Ґ 130 146 162 178 194 210 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 202
Page 45 (WPC1250: Latin 2) HEX 8 9 A B C D E F 0 € SP SP ° Ŕ Đ ŕ đ 128 144 160 176 192 208 224 240 1 SP ' ˇ ± Á Ń á ń 129 145 161 177 193 209 225 241 2 , ' ˘ ˛ Â Ň â ň 130 146 162 178 194 210 226 242 3 SP " Ł ł Ă Ó ă ó 131 147 163 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 203
Page 46 (WPC1251: Cyrillic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 Ђ ђ SP ° А Р а р 128 144 160 176 192 208 224 240 1 Ѓ ' Ў ± Б С б с 129 145 161 177 193 209 225 241 2 , ' ў І В Т в т 130 146 162 178 194 210 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 204
Page 47 (WPC1253: Greek) HEX 8 9 A B C D E F 0 € SP SP ° ΐ Π ΰ π 128 144 160 176 192 208 224 240 1 SP ' ΅ ± Α Ρ α ρ 129 145 161 177 193 209 225 241 2 , ' Ά ² Β SP β ς 130 146 162 178 194 210 226 242 3 ƒ " £ ³ Γ Σ γ σ 131 147 163 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 205
Page 48 (WPC1254: Turkish) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 € SP SP ° À Ğ à ğ 128 144 160 176 192 208 224 240 1 SP ' ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 , ' ¢ ² Â Ò â ò 130 146 162 178 194 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 206
Page 49 (WPC1255: Hebrew) HEX 8 9 A B C D E F 0 € SP SP ° ְ ׀ א נ 128 144 160 176 192 208 224 240 1 SP ' ¡ ± ֱ ׁ ב ס 129 145 161 177 193 209 225 241 2 , ' ¢ ² ֲ ׂ ג ע 130 146 162 178 194 210 226 242 3 ƒ " £ ³ ֳ ׃ ד - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 207
Page 50 (WPC1256: Arabic) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 € گ SP ° ہ ﺫ à ً 128 144 160 176 192 208 224 240 1 پ ' ، ± ء ﺭ ﻝ ٌ 129 145 161 177 193 209 225 241 2 , ' ¢ ² ﺁ ﺯ â ٍ 130 146 162 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 208
Page 51 (WPC1257: Baltic Rim) HEX 8 9 A B C D E F 0 € SP SP ° Ą Š ą š 128 144 160 176 192 208 224 240 1 SP ' SP ± Į Ń į ń 129 145 161 177 193 209 225 241 2 , ' ¢ ² Ā Ņ ā ņ 130 146 162 178 194 210 226 242 3 SP " £ ³ Ć Ó ć ó 131 147 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 209
Page 52 (WPC1258: Vietnamese) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 8 9 A B C D E F 0 € SP SP ° À Đ à đ 128 144 160 176 192 208 224 240 1 SP ' ¡ ± Á Ñ á ñ 129 145 161 177 193 209 225 241 2 , ' ¢ ² Â ̉ 130 146 162 178 194 â ̣ - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 210
Page 53 (KZ1048: Kazakhstan) HEX 8 9 A B C D E F 0 Ђ ђ SP ° А Р а р 128 144 160 176 192 208 224 240 1 Ѓ ' Ұ ± Б С б с 129 145 161 177 193 209 225 241 2 , ' ұ І В Т в т 130 146 162 178 194 210 226 242 3 ѓ " Ə і Г У г у 131 147 163 - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 211
Page 255 (Blank page) TM-L90/TM-L90 Peeler Model Technical Reference Guide HEX 0 1 2 3 4 5 6 7 8 9 A B C D E F 8 9 A B C D E F SP SP SP SP SP SP SP SP 128 144 160 176 192 208 224 240 SP SP SP SP SP SP SP SP - Epson TM-L90 Plus with Peeler | Technical Reference Guide - Page 212
International Character Set * * * * Note: *: Available only for TM-L90 4** models or TM-L90 Peeler 39* models. 212 Appendix
Peeler Model
Technical Reference Guide
410019405
Rev. F