Epson TM-H6000IV with Validation UB-E03 Users Manual
Epson TM-H6000IV with Validation Manual
 |
View all Epson TM-H6000IV with Validation manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson TM-H6000IV with Validation manual content summary:
- Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 1
-E03, designed for EPSON®TM printers, is a 10BASE-T/100BASE-TX Ethernet interface board. This manual provides instructions, including a simple and useful tips on the operation of your equipment. Caution Label The caution label on the product indicates the following precaution. CAUTION: Do not - Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 2
settings. Set the reset signal for pin 31 to "enabled" if you are using a TM printer that has this setting. Refer to the manual for your TM printer for details. For the TM-T90/L90/J7000/J7100/J7500/J7600 printers, set the reset signal for pin 25 of the memory switches to "enabled." For new - Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 3
printer. Then, hold down the push button on the interface card for more than 3 seconds. The printer the printer has printers are the same, you should power on and configure only one printer printer E03 Technical Reference Guide. ❏ Using to the printer and then printer's setting. ❏ Using the TMNet - Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 4
instructions. For customers in other countries, go to the following web site: http://www.epson-pos.com/ Standards and Approvals The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the EPSON power supplies and TM series printers.) Europe - Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 5
© Seiko Epson Corporation 2014. All rights reserved. Printed in Indonesia ͡Ίʹ EPSON®TM 10BASE-T/100BASE-TX UB-E03 POS UB-E03 注意 注記 : 注意 6 4&5#"4&59 TCP、UDP、ICMP、IP、LP/LPR、TCP 10BASE-T/100BASE-TX 1 - Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 6
UB-E03 #"4&5#"4&59 -&% -&% ԫ εΠον UB-E03 31 TM-T90/TM-L90 25 1 2. UB-E03 の 10BASE-T/100BASE-TX 10BASE-T/100BASE-TX ҙ 6 4&5#"4&59 注記 : UB-E03 TM 3 2 - Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 7
UB-E03 IP ଓ PC ping Ping 192.168.192.168 192.168.192.168 注記 : UB-E03 IP UB-E03 6 10 ઃఆ UB-E03 Web 1. Windows Web 2 UB-E03 の IP Enter http://192.168.192.168 3 4 Submit UB-E03 Reset IP PC 3 - Epson TM-H6000IV with Validation | UB-E03 Users Manual - Page 8
❏ TMNet Win Config TMNet Win Config LAN TM Windows UB-E03 TMNet Win Config URL http://www.epson.jp/support/sd/ EPSON および EXCEED YOUR VISION Windows VCCI-A 注意 : LAN 1 2 3 4 5 6 4
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
1
User’s Manual
© Seiko Epson Corporation 2014. All rights reserved.
Printed in Indonesia
Introduction
The UB-E03, designed for EPSON
®
TM printers, is a 10BASE-T/100BASE-TX
Ethernet interface board.
This manual provides instructions, including a simple setup for operators of
POS systems in which the UB-E03 is installed so that the operators can use the
UB-E03 safely and correctly.
Key to Symbols
The symbols in this manual are identified by their level of importance, as
defined below. Read the following carefully before handling the product.
CAUTION:
Cautions must be observed to avoid minor injury to yourself, damage to
your equipment, or loss of data.
Note:
Notes have important information and useful tips on the operation of your equipment.
Caution Label
The caution label on the product indicates the following precaution.
CAUTION:
Do not connect a telephone line, a display module cable, or a drawer
kick-out cable to the UB-E03’s 10BASE-T/100BASE-TX Ethernet connector.
Features and Functions
❏
Protocols: TCP, UDP, ICMP, IP, LP/LPR, TCP socket port
❏
Communication standard: 10Base-T/100Base-TX, Full duplex/half
duplex