Epson R260 Service Manual

Epson R260 - Stylus Photo Color Inkjet Printer Manual

Get Epson R260 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343859043
View all Epson R260 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson R260 manual content summary:

  • Epson R260 | Service Manual - Page 1
    SERVICE MANUAL Color Inkjet Printer EPSON Stylus Photo R260/R265/R270 R360/R380/R390 SEIJ06001
  • Epson R260 | Service Manual - Page 2
    OF WORK. 3. WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL INSTRUCTED TO DO SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER SUPPLY AND OTHER ELECTRONIC COMPONENTS. 4. WHEN DISASSEMBLING OR ASSEMBLING
  • Epson R260 | Service Manual - Page 3
    and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. manuals4you.com Manual Configuration This manual consists of six chapters and
  • Epson R260 | Service Manual - Page 4
    EPSON Status Monitor 3 error messages are changed. 3.3.1 Troubleshooting Problems with Error Messages (p.36) is modified. (CR Encoder) 3.4.4 Problems with Interfaces (p.55): Troubleshooting 4.3.1 Removing the USB Board (R260/R265/R270 only) (p.76): . Chapter 5 5.1.1 Servicing Adjustment Item List (p.
  • Epson R260 | Service Manual - Page 5
    Error Indication Method 33 3.3 Troubleshooting by Error Message 36 3.3.1 Troubleshooting Problems with Error Messages 36 3.4 Troubleshooting by Symptom 48 3.4.1 Problems in Printing Operation 48 3.4.2 Power Problems 53 3.4.3 Ink-related Problems 53 3.4.4 Problems with Interfaces 55 Chapter
  • Epson R260 | Service Manual - Page 6
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.2.8 Right Front Housing / Left Front Housing 72 4.2.9 Front Housing 73 4.3 Removing Control Boards 76 4.3.1 Removing the USB Board (R260/R265/R270 only 76 4.3.2 Removing the Main Board Unit 78 4.3.3 Disassembling the Main Board Unit 80 4.3.4
  • Epson R260 | Service Manual - Page 7
    PRODUCT DESCRIPTION CHAPTER 1
  • Epson R260 | Service Manual - Page 8
    Stylus Photo R260/R265/R270 and R360/R380/R390 are A4 home-use photo printers. Besides printing on papers, printing directly on CDs/DVDs are available. The main features are; Printing „ Offers up to 5760(H) x 1440(V) dpi resolution „ 6-color individual ink cartridges „ Borderless, edge-to-edge photo
  • Epson R260 | Service Manual - Page 9
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.2 Basic Specifications 1.2.1 Printing Basic Specifications Table 1-2. Basic Specifications Item Print method Print head Printing direction Resolution Input buffer Description On-demand inkjet printer Black ink: 90 nozzles Color
  • Epson R260 | Service Manual - Page 10
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.2.2 Interfaces The printers are equipped with the following interfaces. † USB I/F „ USB DEVICE (for connecting a PC) „ USB HOST *1 (for connecting a DSC or USB storage device, or for wireless printing using a Bluetooth adaptor (option
  • Epson R260 | Service Manual - Page 11
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.2.2.3 Memory Card Slot (R360/R380/R390 only) Table 1-8. Compatible Card Types by the Card Slot Priority Slot 1 CF Type II 2 xD-Picture card Memory Stick/ Memory Stick PRO 3 SD/MMC Compatible Card Type Compact Flash Microdrive
  • Epson R260 | Service Manual - Page 12
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.3 Standalone Printing (R360/R380/R390 only) The Stylus Photo R360/R380/R390 offers Direct-Print function that allows the user to print directly from a memory card without using a PC. Besides printing still images, printing frames of a
  • Epson R260 | Service Manual - Page 13
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B not guaranteed which files are selected when the number of files is 1000 or more. When photo data files to which a camera has assigned numbers over 999 are specified to be printed, they can be printed unless the total number of files
  • Epson R260 | Service Manual - Page 14
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.4 Backup Function (R360/R380/R390 only) Stylus Photo R360/R380/R390 allows the user to easily make a backup of his/her memory card without using a computer. Furthermore, photos in a backup copy can be printed directly from the printer.
  • Epson R260 | Service Manual - Page 15
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Writing Format for CD-R Media Writing to CD-R media is made in multisession cannot be made. „ The printer and an external device must be directly connected with a USB cable. Connection via a HUB is not supported. „ A connection with a PC
  • Epson R260 | Service Manual - Page 16
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Backup-related errors Table 1- "Backup canceled" when a backup error occurs. The leftmost 2-digit shows an error code controlled by the printer firmware. See Table 1-12. Backup Error FW Control Code List on the next page to identify the
  • Epson R260 | Service Manual - Page 17
    layouts for CD/DVD jacket printing on A4 sized paper NOTE: The Stylus Photo R260/R265/R270 do not provide the standalone CDs/DVDs print function. To print directly on CDs/DVDs with those models, the print setting must be made on a PC and sent to the printer. Product description CD/DVD Print (R360
  • Epson R260 | Service Manual - Page 18
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 1.6 Operation Panel 1.6.1 Operation Panel Appearance of the operation panels are shown below. Stylus Photo R360/R380/R390 Operation Panel Power LED Mode LEDs Figure 1-4. Stylus Photo R360//R380/R390 NOTE: The operation panel shown above is that of a
  • Epson R260 | Service Manual - Page 19
    the card being accessed. Stylus Photo R260/R265/R270 Three LEDs; power, ink, paper are provided. • Power LED (green): Lights during the printer is powered. Flashes when printing or other operations are in progress. • Ink LED (red) / Paper LED (red): Lights or flashes when an error occurs. CHECK
  • Epson R260 | Service Manual - Page 20
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.7 Specifications Common to Class B Table 1-16. Power Consumption Printer status Model Name 100-120V model 220-240V model Printing*1 R260/R265/R270 R360/R380/R390 Approx. 12W Approx. 17W Sleep mode R260/R265/R270 R360/R380/R390
  • Epson R260 | Service Manual - Page 21
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 1.7.5 Dimensions Table 1-18. Dimensions Item Weight Dimensions With covers closed (W x D x H) With covers opened R260/R265/R270 6.2 kg 453 x 337 x 194 mm 453 x 538 x 285 mm R360/R380/R390 6.6 kg 453 x 343 x 194 mm 450 x 538 x 285 mm Revision B
  • Epson R260 | Service Manual - Page 22
    OPERATING PRINCIPLES CHAPTER 2
  • Epson R260 | Service Manual - Page 23
    boards of Stylus Photo R260/R265/R270 and R360/R380/R390. 2.1.1 Printer Mechanism The main components of the printer mechanism are shown in the table below. Table 2-1. Printer Mechanism Main Components Component Function CR Unit Moves along the CR shaft to print on paper being powered by the
  • Epson R260 | Service Manual - Page 24
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 2.1.2 Motors & Sensors Table 2-3. List of Motors & Sensors No. Motor/Sensor Name Function 1 Printhead F3-MACH head (6 colors x 90 nozzles) 2 CR motor Type: DC motor Drive voltage: 42V DC ± 5% (voltage applied to the driver) Coil resistance:
  • Epson R260 | Service Manual - Page 25
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 2.2 Electrical Circuit Operating Principles The electric circuits of the Stylus Photo R260/R265/R270 and R360/R380/R390 consist of the following boards. Table 2-4. Main Boards & Model Numbers Board Name Main Board Power Supply Board Panel Board
  • Epson R260 | Service Manual - Page 26
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 2.2.2 Components of Control Boards Table 2-5. Components of Control Boards Board Name Incorporated Components R360/R380/R390 R260/R265/R270 † Logic circuit (ASIC incorporated in the CPU core, Flash ROM x 2, SDRAM x 1, DDR1 x 1) † Logic
  • Epson R260 | Service Manual - Page 27
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 2.2.3 Circuit Block Diagram Flash-ROM (IC9) SDRAM (IC11) DDR-DRAM Data (IC7) Address Data Address RTC (IC3) CPU-ASIC (IC4) Serial Flash-ROM (IC5) LCD C658 Panel Board C658 Panel_B Board C658 STG Board CN4 CN3 CN1 USB (CN2) C653 PSB/PSE
  • Epson R260 | Service Manual - Page 28
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Flash-ROM (IC1) SDRAM (IC2) RTC (IC3) Serial Flash-ROM (IC4) C653 Panel Board CN5 USB HOST (CN2) USB (CN1) C653 PSB/PSE Board CN3 CPU-ASIC (IC5) Motor Driver (IC8) CN8 CN7 CN6 CN4 CN14 CN13 Head Driver (IC7) Q2, Q5, Q6, Q7
  • Epson R260 | Service Manual - Page 29
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 2.3 Banding Reduction System (BRS) / Paper Feed Amount Profile Correction (PFP) † Overview In order to ensure high print quality and high print speed, this product incorporates the Banding Reduction System (BRS) and Paper Feed Profile (
  • Epson R260 | Service Manual - Page 30
    TROUBLESHOOTING CHAPTER 3
  • Epson R260 | Service Manual - Page 31
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3.1 Overview This chapter provides how to troubleshoot problems analyzing the cause based on the error messages displayed on the printer and the observed symptom. Identify and troubleshoot the problem referring to the tables on the following pages.
  • Epson R260 | Service Manual - Page 32
    of the printer driver when a problem arises during various operations; power-on sequence, paper feeding, ink drawing, printing, and so on. 3.2.1 Error Indication Method The Stylus Photo R360/R380/R390 are equipped with a LCD. You can solve most of the troubles following the instructions shown on
  • Epson R260 | Service Manual - Page 33
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-4. List of Error Messages Error Name R360/R380/R390 Messages on the LCD R260/R265/R270 LED Indications Power Paper Ink STM3 Message Error Cause See the table for Troubleshooting Communication error - Check all
  • Epson R260 | Service Manual - Page 34
    position. Close the CD/DVD guide. Table 3-4. List of Error Messages R260/R265/R270 LED Indications Power Paper Ink STM3 Message Error Cause See the table for Troubleshooting Reload the paper and set the front tray to the paper position by pulling up the tray lever. Then - Light - press the
  • Epson R260 | Service Manual - Page 35
    out required adjustments. 3.3.1 Troubleshooting Problems with Error Messages Occurrence Timing Symptom At power-on The printer does not work at all. Table 3-5. Troubleshooting for Communication Error Failed Part Check Point Remedy Panel Board/ Panel FFC P/S ASSY USB cable Printer driver
  • Epson R260 | Service Manual - Page 36
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Occurrence Timing Symptom Failed Part CR Motor Main Frame Table 3-6. Troubleshooting " (P.131) At power-on • CR motor does not rotate at all. • CR Unit hits against the right side of the Main Frame. CR Guide Shaft PG Cam CR
  • Epson R260 | Service Manual - Page 37
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Occurrence Timing Symptom Failed Part Table 3-6. Troubleshooting for Fatal Error Check "ASF Unit"(p.104) At power-on • The CR Unit hits against the Change Lever which has come down toward the front of the printer. • The error appears after
  • Epson R260 | Service Manual - Page 38
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-6. Troubleshooting for Fatal Error Occurrence Timing At power-on Symptom Failed Part Check Point Remedy Reference • The CR Unit hits against the Change Lever which has come down toward the front of the printer. • The error
  • Epson R260 | Service Manual - Page 39
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Occurrence Timing Table 3-7. Troubleshooting for Ink Cartridge Detection Error/ Ink Cover Open Error/ Cartridge Empty Error Symptom Failed Part Check Point Remedy 1. Is the memory chip on the cartridge chipped or 1. Replace the ink cartridge.
  • Epson R260 | Service Manual - Page 40
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-8. Troubleshooting printer performs paper feeding operation, the paper is not fed into the printer. Front Paper Guide Paper is fed into the printer, but ejected at once without any printing operation. PE Sensor Extension Spring
  • Epson R260 | Service Manual - Page 41
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Occurrence Timing Symptom Paper is fed into the printer, but ejected at once without any printing operation. Table 3-8. Troubleshooting Roller. 1. Is the Upper Paper Guide disengaged from the Upper Paper Guide* Main Frame? Note : *
  • Epson R260 | Service Manual - Page 42
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Occurrence Timing Symptom The LD Roller rotates normally to feed paper, but the Hopper does not move. The LD Roller rotates normally, but paper is not fed into the printer. Table 3-9. Troubleshooting not solve the problem, replace the
  • Epson R260 | Service Manual - Page 43
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Occurrence Timing Symptom Table 3-9. Troubleshooting for No Paper Error Failed Part Check Point Remedy 3. Is the clutch damaged? 3. Replace the ASF Unit. Revision B Reference The PF Motor drive force is
  • Epson R260 | Service Manual - Page 44
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Occurrence Timing Symptom Table 3-10. Troubleshooting for CDR set to the printer, but the error occurs. When printing on CDs/DVDs 1. Is the CDR Guide Detection Assy cable not connected to the Main Board? CDR Guide Detection ASSY 2.
  • Epson R260 | Service Manual - Page 45
    Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Occurrence Timing Symptom Table 3-10. Troubleshooting for CDR Tray Error Failed Part Check Point 1. Is there any paper dust or ink stain on the PW Sensor? Cable Remedy 1. Clean off any dirt on the PW Sensor. Reference When printing
  • Epson R260 | Service Manual - Page 46
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Occurrence Timing When printing on CDs/DVDs Symptom Table 3-11. Troubleshooting for CDR Guide Error Failed Part Check Point 1. Is the CDR Guide Detection Assy cable not connected to the Main Board? CDR Guide Detection ASSY 2. Is
  • Epson R260 | Service Manual - Page 47
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.4 Troubleshooting by Symptom 3.4.1 Problems in Printing Operation This section provides how to troubleshoot the possible problems on the printer mechanism. No error message appears for most of the troubles described here. In the
  • Epson R260 | Service Manual - Page 48
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Symptom Possible Cause Table 3-12. Troubleshooting Paper Feeding Problems Check during printing is abnormal. Something interferes with the operation of the CR Unit. Table 3-14. Troubleshooting Carriage Movement Problems Check
  • Epson R260 | Service Manual - Page 49
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B † Printer initialization operation is aborted Table 3-15. Troubleshooting Initialization Stop Problems Symptom Possible Cause Check Point Remedy Improper installation of the EJ Frame Are the tabs of the EJ Frame disengaged?
  • Epson R260 | Service Manual - Page 50
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B † Print quality problems Symptom Possible Cause Dirt on the Printhead. Printed image has The absorber of the Cap Unit missing colors, contacts with the Printhead surface and the missed during printing. colors are always Head FFC
  • Epson R260 | Service Manual - Page 51
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Symptom Possible Cause Dirt on the CR shaft PF Roller failure Ink cartridge failure A malfunction of Carriage movements Improper platen gap Printed image has white banding. Some gear(s) is (are) damaged. Dirt on the Printhead is
  • Epson R260 | Service Manual - Page 52
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.4.2 Power Problems The printer does not work at all after power-on. LEDs do not light up. Possible Cause Power code failure Improper power supply Poor connection of the PS Assy connector The fuse burned out Abnormal voltage output of
  • Epson R260 | Service Manual - Page 53
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B † Printing cannot be made properly (printed image is faint, blurry, smeared, or etc.) Table 3-19. Troubleshooting Printing Problems Symptom Possible Cause Check Point Remedy Ink cartridge failure Replace the ink cartridge with a
  • Epson R260 | Service Manual - Page 54
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.4.4 Problems with Interfaces This section provides how to troubleshoot problems on the USB interface and memory card slot. † USB interface error Table 3-21. Troubleshooting USB Connection Errors Possible Cause Check Point Remedy
  • Epson R260 | Service Manual - Page 55
    DISASSEMBLY/ASSEMBLY CHAPTER 4
  • Epson R260 | Service Manual - Page 56
    when disassembling Stylus photo R260/R265/R270 and R360/R380/R390. Revision B W A R N IN G C A U T IO N „ Disconnect the power cable before disassembling or assembling the printer. „ If you need to work on the printer with power applied, strictly follow the instructions in this manual. „ Wear
  • Epson R260 | Service Manual - Page 57
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.1.2 Tools Use only specified tools to avoid damaging the printer. Table 4-1. List of Tools Tool Phillips Screw Driver (No.1) Phillips Screw Driver (No.2) Flathead Screw Driver Precision Screw Driver #1 (flathead) Tweezers Long-nose pliers
  • Epson R260 | Service Manual - Page 58
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.1.4 Work Completion Checklist Whenever the printer is serviced, use the checklist shown below to confirm all work is completed properly and the printer is ready to be returned to the user. Make sure to always check the maintenance counter before
  • Epson R260 | Service Manual - Page 59
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B PROTECTION FOR TRANSPORTATION Before packing the printer to be returned to the user, attach several pieces of strong tape and vinyl sheet to the specified points to prevent damaging the printer during transportation. † Securing the
  • Epson R260 | Service Manual - Page 60
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 † Protecting the exterior parts from the edges with Stacker edges 30mm Revision B 4.1.5 Required Preparation before Disassembly Make sure to carry out the following operations before disassembling the printer. † When the Main Board needs to be
  • Epson R260 | Service Manual - Page 61
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.1.7 How to Unlock the Carriage † Unlocking the carriage is required for be taken to avoid injury from sharp metal edges. „ Power the printer and turn it off forcedly by disconnecting the power cable when the CR Unit is unlocked and moved away
  • Epson R260 | Service Manual - Page 62
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.1.9 Differences in Disassembly Procedure by Model The table below lists the differences in disassembly procedure between the Stylus Photo R260/R265/R270 and R360/R380/R390. For more details on each procedure, refer to the page given
  • Epson R260 | Service Manual - Page 63
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.1.10 Disassembly/Assembly Procedures The flowchart below lists the step-by-step disassembly procedures. When disassembling each unit, refer to the page number shown in the figure. START Paper Support (p.65) Printer Cover (p.65) Front Cover (p.
  • Epson R260 | Service Manual - Page 64
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.2 Removing Exterior Parts/Components 4.2.1 Paper Support † Parts/Components need to be removed in advance: Nothing † Removal procedure 1. Open the Paper Support. 2. Disengage the right shaft of the Paper Support from the bushing of the ASF Unit
  • Epson R260 | Service Manual - Page 65
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2.3 Front Cover † Parts/Components need to be removed in advance: Nothing † Removal procedure 1. Open the Front Cover. 2. Raise the CDR Guide Lever to lower the Stacker. 3. While pushing , disengage the left and right positioning holes
  • Epson R260 | Service Manual - Page 66
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Hook : Tab Figure 4-18. Disengaging the Hook and Tabs 4. Remove the Left Housing in the same manner. Before screwing the
  • Epson R260 | Service Manual - Page 67
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.2.5 Upper Housing † Parts/Components need to be removed in advance Paper Support / Printer Cover Housing to disengage the two positioning holes of the housing from the guide pins of the Lower Housing, and remove the Upper Housing avoiding contact
  • Epson R260 | Service Manual - Page 68
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.2.6 Panel Unit † Parts/Components need to be removed in advance Paper Support / Printer Cover / Front Cover upward and disengage the hook [Backside] Removal Direction Screw Driver Figure 4-24. Removing the Panel Unit Disengage the hook When
  • Epson R260 | Service Manual - Page 69
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.2.7 EMI Frame / Waste Ink Tray † Parts/Components need to be removed in advance Paper Support / Printer the EMI Frame into the notch of the Waste Ink Tray. 3. Insert the positioning hole (2) over the guide pin on the main frame. 4. Tighten the
  • Epson R260 | Service Manual - Page 70
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ Waste Ink Tray Removal C A U T IO N „ When removing the Waste Ink Tray, take extra care not to spill ink and contaminate the printer and surroundings. „ Do not pull the Waste Ink Tray too much to remove it, as it is connected to the Ink System
  • Epson R260 | Service Manual - Page 71
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ Wipe off any ink on the joint portion of the Waste Ink Tube before reconnecting the tube. Ink on the joint portion makes the tube likely to get disconnected. „ Insert the Waste Ink Tube until its leading edge reaches the point where the shaft of
  • Epson R260 | Service Manual - Page 72
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Upper Tab Guide Pin Left Front Housing Removal Direction Lower Tab Figure 4-34. Tabs of the Right/Left Front Housings Revision B 4.2.9 Front Housing † Parts/Components need to be removed in advance Paper Support / Printer Cover / Front Cover /
  • Epson R260 | Service Manual - Page 73
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. With a flathead screwdriver or similar tool, disengage the two tabs on the inner left and right sides. 4. From the bottom side of the Printer, insert a flathead screw driver into the hole of the Lower Housing to disengage the two tabs. (With R260
  • Epson R260 | Service Manual - Page 74
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ Install the Front Housing following the steps below 1. Install the Slot Cover. (R360/R380/R390 only) 2. With the two hooks
  • Epson R260 | Service Manual - Page 75
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.3 Removing Control Boards 4.3.1 Removing the USB Board (R260/R265/R270 only) † Parts/Components need to be removed in advance All exterior parts/components † USB Board removal CHECK P O IN T „ R260 Main Board. Refer to R260/ R265/R270 & R360/
  • Epson R260 | Service Manual - Page 76
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. From the rear side, push the positioning pin out with a screw driver or similar tool, and slide the FFC Holder upward to remove it from the Middle Housing. FFC Holder Removal Direction Push Screw driver Positioning Pin FFC Holder Figure 4-
  • Epson R260 | Service Manual - Page 77
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.3.2 Removing the Main Board Unit † Parts/Components need to be removed in advance All exterior parts/components / USB Board (R260 CN9 CN4 White CDR Guide Detection Assy 4pin Power Supply 3pin Disassembly/Assembly Removing Control Boards 78
  • Epson R260 | Service Manual - Page 78
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Remove the four screws. (For R260/R265/R270, three screws only) • Screw (3 pcs.): C.B.P. M3x10 (tightening torque: 5-7 kgf.cm) • Screw (1 pc.): C.P. M3x6 (tightening torque: 7-9 kgf.cm) (The numbers shown in the figure
  • Epson R260 | Service Manual - Page 79
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ Install the Main Board Unit Support Shield Plate. (R360/ R380/R390 only) • Screw : C.B.S. M3x8 (tightening torque: 7-9 kgf.cm) MB Cover : Screw Hole : Guide Pin Figure 4-58. Reinstalling the Main Board Unit (2) R260/R265/ R270 CB Support
  • Epson R260 | Service Manual - Page 80
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4. Remove the Upper Shield Plate MB the Main Board. • Screw : C.P. M3x10 (tightening torque: 5-7 kgf.cm) Lower Shield Plate MB Main Board R260/R265/R270 Figure 4-63. Removing the Main Board „ Screw the Upper Shield Plate MB of the R360/R380/R390
  • Epson R260 | Service Manual - Page 81
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.3.4 Removing the Card Board ( R380/R390 are equipped with a Card Board. Remove the Card Board after removing the Main Board. Refer to R260/R265/ R270 & R360/R380/R390 Disassembly Flowchart(p.64). 1. Remove the FFC Holder. (See FFC Holder removal
  • Epson R260 | Service Manual - Page 82
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.3.5 Disassembling the Panel Unit † Panel Disengage the Ferrite Core from the hook. Ferrite core Ferrite core CHECK P O IN T Since the R260/R265/R270 are not equipped with a LCD panel, the removal procedure of the Panel Board differs from
  • Epson R260 | Service Manual - Page 83
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 5. Remove the screw and remove the Panel Board. • (9) and the LED Light Guide Plate. 8 1 2 45 6 3 7 9 LED Light Guide Plate Figure 4-72. Removing the SW Buttons Figure 4-73. Removing the FFC † Removing the Panel Board (for R260/R265/R270) 1.
  • Epson R260 | Service Manual - Page 84
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4. Remove the SW Button (1)(2)(3) and the LED Light Guide Plate. 123 LED Light Guide Plate Figure 4-76. Removing the SW Buttons (R260/R265/R270) 5. Peel off the double-sided tape and remove the two FFCs from the Shield Plate PNL. • Double-sided
  • Epson R260 | Service Manual - Page 85
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.3.6 Middle Housing † Parts/Components need to be removed in advance All exterior parts/components / Card Board (USB Board) / Main Board
  • Epson R260 | Service Manual - Page 86
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.4 Removing the Printer Mechanism † Parts/Components need to be removed in advance All exterior parts/components / All control boards / Middle Housing 4.4.1 Removing the Printer Mechanism † Removal procedure C A U T IO N „ Take extra care to
  • Epson R260 | Service Manual - Page 87
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 2. Remove the six screws that secure the Printer Mechanism. • Screw : C.B.P. M3x8 ( S TM E N T R E Q U IR E D Whenever the Printer Mechanism is replaced, the required adjustments must be carried out. •See "Table 5-4. Adjustment Items (p.116)"
  • Epson R260 | Service Manual - Page 88
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5 Disassembly of the Printer Mechanism 4.5.1 CR Scale C A U T IO N „ • "4.1.8 Sharp Metal Edges (Danger!)" (p.62) „ During the disassembly/reassembly of the Printer Mechanism, take extra care not to touch the CR Scale with bare hands, and not
  • Epson R260 | Service Manual - Page 89
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5.2 APG Unit C 1 2 Figure 4-90. Removing the APG Unit Revision B „ Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" . Disassembly/Assembly Disassembly of the Printer Mechanism 90
  • Epson R260 | Service Manual - Page 90
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Install the APG Unit to the Main Frame. Pin APG Unit Figure 4-93. Reinstalling the APG Unit (3) 4. Check that the
  • Epson R260 | Service Manual - Page 91
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Disconnect the FFC from the connector ( ) on the Head Board. FFC for CSIC Figure 4-96. Removing the FFC for CSIC 4. While disengaging the hook of the Head FFC Cover Inner with a flathead screw driver Disassembly of the Printer Mechanism 92
  • Epson R260 | Service Manual - Page 92
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 C A U T IO N Take extra care not to spill ink and contaminate the surroundings. Be extremely careful not to touch the nozzle surface, the ink E D Whenever the Printhead is removed/replaced, the required adjustments must be carried out. •See "Table
  • Epson R260 | Service Manual - Page 93
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5.4 Waste Ink Pad † Parts/Components need to be removed in advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism † Removal procedure C A U T IO N When removing the Waste Ink Pad, take extra care not to contaminate
  • Epson R260 | Service Manual - Page 94
    EPSON Stylus Photo R260/R265/R270, R360/R380 advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism † Removal procedure C A U T IO N Take CDR Guide Lever. CDR Guide Lever A D JU S TM E N T R E Q U IR E D Whenever the P/S Assy is replaced, the required adjustment
  • Epson R260 | Service Manual - Page 95
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4. Follow the steps below to remove the CDR Guide Lever Spring. 1) Pull the end A toward you. 2) Pull the end B out of the notch. 3) Pull the end A out of the shaft, and remove the CDR Guide Lever Spring. 2 A B 1 A CDR Shaft 3 Figure 4-110.
  • Epson R260 | Service Manual - Page 96
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 When installing the Stacker Assy, insert the tabs of the Left/ Right Stacker Guides into the hole of the Lower Housing, and secure the guides with the screws. Tighten the screws in the order given in Fig.4-111. Lower Housing Left Stacker Guide Right
  • Epson R260 | Service Manual - Page 97
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 1. Move the CR Unit to the center. 2. Remove the screw (1) that secures the Cap section. • Screw : C.B.S. M3x6 (tightening torque: 7-9 kgf.
  • Epson R260 | Service Manual - Page 98
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5.8 CR Motor C A U T IO N Take extra /Components need to be removed in advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism / CR Scale † Removal procedure CHECK P O IN T Refer to the Orientation Definition below
  • Epson R260 | Service Manual - Page 99
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" „ When installing the CR Motor, install it so that the print Cable on the left side of the printer referring to the page below. "Routing
  • Epson R260 | Service Manual - Page 100
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Direction EJ Frame Assy Figure 4-130. Removing the EJ Frame Assy „ Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" Disassembly/Assembly Disassembly of the Printer Mechanism 101
  • Epson R260 | Service Manual - Page 101
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ When installing the Front Frame mm) 2 Figure 4-134. Acetate Tape Position „ Route the CR Motor/PE Sensor cables on the rear of the printer referring to the page below. Figure 4-123 "Removing the CR Motor (2)" (p.99) „ Route the PF Motor/PF Encoder
  • Epson R260 | Service Manual - Page 102
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ Removing the PF Motor TM E N T R E Q U IR E D Whenever the PF Motor is replaced, the required adjustments must be carried out. See "Table 5-4. Adjustment Items (p.116)" in Chapter 5 Disassembly/Assembly Disassembly of the Printer Mechanism 103
  • Epson R260 | Service Manual - Page 103
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5.11 ASF Unit † Parts/Components need to be removed in advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism / Ink System † Removal procedure CHECK P O IN T Refer to the Orientation Definition below for the
  • Epson R260 | Service Manual - Page 104
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 7. Remove the Combination Gear (10, 15.2), and remove the ASF Unit. Combination Gear Removal Direction [Rear side] Figure 4-143. Removing the ASF Unit ASF Unit „ Lubrication is required boards / Middle Housing / Printer Mechanism / CR Scale /
  • Epson R260 | Service Manual - Page 105
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Disengage the end of the Spring (2) from the hook, and the other end from the slit of the CR Unit, and remove the Head FFC. Head FFC CR Unit Figure 4-150. Removing the CR Unit (6) Disassembly/Assembly Disassembly of the Printer Mechanism 106
  • Epson R260 | Service Manual - Page 106
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 „ Lubrication is required. See the page given below for Cartridge. 3. Remove the Cartridge Cover pulling out its two guide pins. Right side view of the hinge : cut position Convex portion Cartridge Cover : Guide Pin Hook Hinge, Cover Cartridge
  • Epson R260 | Service Manual - Page 107
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5.13 Upper Paper Guide C A U T IO N „ Be sure to follow the procedure below to remove the Upper Paper Guide to avoid damaging the PE Sensor Lever. „ It is recommended to place a transparent sheet between the Upper and Front Paper Guides to avoid
  • Epson R260 | Service Manual - Page 108
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5.14 Front Paper Guide Assy/APG Sensor Assy C A U T IO N Do not touch the surface of the rubber roller of the EJ Roller Assy and the coated part of the PF Roller Assy as it can adversely affect the print quality. † Parts/Components need to be
  • Epson R260 | Service Manual - Page 109
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 5. Remove the Front Paper Guide Assy, following the steps below. (1) Lift part to disengage the left side of the Front Paper Guide Assy. (2) Slide the assy leftward little by little to disengage the right side of the assy. (3) Remove the Front
  • Epson R260 | Service Manual - Page 110
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5.15 CDR Guide Detection Assy † Parts/Components need to be removed in advance All exterior parts/components / All control boards / Middle Housing / Printer Mechanism / CR Scale / APG Unit / Printhead / Ink System / ASF Unit / Upper Paper Guide /
  • Epson R260 | Service Manual - Page 111
    ADJUSTMENT CHAPTER 5
  • Epson R260 | Service Manual - Page 112
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.1 Adjustment Items and Overview This chapter describes adjustments necessary after the disassembly/reassembly of the printer. 5.1.1 Servicing the Timing Belt manually, and check by software. Use the adjustment program to print the
  • Epson R260 | Service Manual - Page 113
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Adjustment Items Function Item Bi-D adjustment First dot/PW adjustment PF adjustment BRS/PFP adjustment CR motor heat protection control Table 5-1. Adjustment Items Purpose Method Outline This adjustment is made to correct the print
  • Epson R260 | Service Manual - Page 114
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Maintenance Items Function Item Head Cleaning Waste ink pad protection counter reset Ink charge Table 5-2. Maintenance Items Purpose Method Outline This function is used to execute Cleaning efficiently when ink is not delivered from
  • Epson R260 | Service Manual - Page 115
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.1.2 Replacement Part Adjustment Items The following table indicates the adjustment items for replacement parts. Note: "Required" in this table indicates the adjustment item that must be executed when the corresponding part has been
  • Epson R260 | Service Manual - Page 116
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Priority order Waste Ink Tray Remove Replace Waste Ink Pad Remove Replace CR Unit Remove Replace Paper Eject Remove Frame Assy Replace Printer Remove Mechanism Replace Table 5-4. Adjustment Items 1 2 3 4 5 6 7 8 9 10
  • Epson R260 | Service Manual - Page 117
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.2 Adjustment by Using Adjustment Program This section explains how to judge print samples by using the adjustment program. Follow the instructions of the adjustment program for details of the adjustment methods. 5.2.1 Top Margin
  • Epson R260 | Service Manual - Page 118
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 † Microweave Pattern 5.2.3 Bi-D Adjustment The pattern shown below is printed for each of the 4 print modes. Revision B +3 +2 +1 0 -1 -2 -3 Figure 5-3. Head angular adjustment Pattern Printing (2) [Judgment method] Examine the printout +3
  • Epson R260 | Service Manual - Page 119
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 5.2.4 PW Adjustment/First Dot Adjustment Patterns are printed as shown below. 5 mm -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -8 -8 -7 -7 -6 -6 -5 -5 -4 -4 -3 -3 -2 -2 -1 -1 0 0 1 1 2 Area where A and B overlap 2
  • Epson R260 | Service Manual - Page 120
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 5.2.5 PF Adjustment † PF-Standard Area Patterns are printed as shown below. 5 4 3 2 1 0 -1 -2 -3 -4 -5 Figure 5-6. PF adjustment (Standard Area) Pattern Printing [Judgment method] Input the value shown above the patterns which has no gap between the
  • Epson R260 | Service Manual - Page 121
    EPSON special thin paper, SF, etc. Rubbing with PG1.2 is avoided Envelopes 2.35 Rubbing with PG1.2 and 1.7 is avoided 4.2 CD-R printing At ink replacement after adjustment.) Refer to "4.4 Removing the Printer Mechanism" (p.87) „ With EPSON Stylus Photo R260/R265/R270, R360/R380/R390, four stages
  • Epson R260 | Service Manual - Page 122
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B † Adjustment procedure „ Specified PG value: 1.2 ± 0.1 mm 1. Install new ink cartridges in the carriage. 2. Remove the left edge with the second rib of the Front Paper Guide. And place another 1.15 mm thickness gauge on the right aligning
  • Epson R260 | Service Manual - Page 123
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.3 Banding Stylus Photo RX560/RX580/RX590 CIS Use the internal scanner. CHECK P O IN T Depending on the sensor type of the scanner to use for the adjustment, drying time required after the BRS adjustment pattern has been printed
  • Epson R260 | Service Manual - Page 124
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B † Adjustment Flow Carry out the adjustment following the adjustment flow below. START Printing the BRS Adjustment Pattern Printing the PFP Check Pattern c Scanning the BRS Adjustment Pattern Judging the Check Pattern NG OK Error?
  • Epson R260 | Service Manual - Page 125
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 † Scanning the BRS Adjustment Pattern 5. Set the printed pattern and the PFP Base Scale on the document table and click the [Scan] button on the "3. Scan Test Pattern" column. 6. According to the scanned
  • Epson R260 | Service Manual - Page 126
    EPSON Stylus Photo R260 calibration values are automatically calculated and are written to the serial flash ROM. If an error occurs, check that the document table Printing the PFP Check Pattern 6. Set 4 x 6 Premium Glossy Photo Paper on the paper support and click the [Print] Button on the "4. Print
  • Epson R260 | Service Manual - Page 127
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 † Judging the Check Pattern 7. Referring to Fig. 5-18 check that there is no white or overlapped bands in all the check patterns. If any bands are found, carry out the steps below. 1. Re-print the check pattern to see if the bands appear again. 2.
  • Epson R260 | Service Manual - Page 128
    MAINTENANCE CHAPTER 6
  • Epson R260 | Service Manual - Page 129
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 6.1 Overview This section provides information to maintain the printer in its optimum condition. 6.1.1 Cleaning This printer has no mechanical components which require regular cleaning except the Print Head. Therefore, when returning
  • Epson R260 | Service Manual - Page 130
    Stylus Photo R260/R265/R270, R360/R380/R390 6.1.3 Lubrication The type and amount of the grease used to lubricate the printer parts are determined based on the results of the internal evaluations. Be sure to apply the specified type and amount of the grease to the specified parts during servicing
  • Epson R260 | Service Manual - Page 131
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B LUBRICATION OF FRONT PAPER GUIDE ASSY Front Paper Guide Assy (left) PF Roller Shaft, EJ Roller Shaft and Bushing (3 points) G-71 ø 1 x 3 mm x 3 points Apply after
  • Epson R260 | Service Manual - Page 132
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Front Frame contact point (right) Contact position of the Front Frame and the PE Frame Assy (2 points) Rib <
  • Epson R260 | Service Manual - Page 133
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Contact point between CR Timing Belt is free from grease. Figure 6-13. Lubrication of the CR Shaft (2) LUBRICATION OF INK SYSTEM Contact point between Main Frame and I/S Application Point On the Main Frame where
  • Epson R260 | Service Manual - Page 134
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Rim of the APG Unit Spur Gear 28.8 Around the rim of the Spur Gear 28.8 G-71 <
  • Epson R260 | Service Manual - Page 135
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 LD Roller Shaft (Curved surface) (Ribs (3) LUBRICATION OF LEFT/RIGHT STACKER GUIDE Left Stacker Guide Right Stacker Guide Along the groove of the Left/Right Stacker Guides to where the CDR Guide Shaft is set. G-
  • Epson R260 | Service Manual - Page 136
    APPENDIX CHAPTER 7
  • Epson R260 | Service Manual - Page 137
    EPSON Stylus Photo R260/R265/R270, R360/R380/R390 7.1 Exploded Diagram / Parts List This manual does not provide exploded diagrams or parts list. For the information, see SPI (Service Parts Information). Revision B 7.2 Electrical Circuits The electric circuit diagrams below are shown at the
  • Epson R260 | Service Manual - Page 138
    Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Sheet : 1/4
  • Epson R260 | Service Manual - Page 139
    Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Rev. : C Sheet : 2/4
  • Epson R260 | Service Manual - Page 140
    Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Rev. : B Sheet : 3/4
  • Epson R260 | Service Manual - Page 141
    Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Rev. : A Sheet : 4/4
  • Epson R260 | Service Manual - Page 142
    Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 PNL Rev. : A Sheet : 1/1
  • Epson R260 | Service Manual - Page 143
    Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 PNL-B Rev. : A Sheet : 1/1
  • Epson R260 | Service Manual - Page 144
    Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 STG Rev. : B Sheet : 1/1
  • Epson R260 | Service Manual - Page 145
    Model : PM-G850 Stylus Photo R260/R265/R270 Board : C653 MAIN Rev. : C Sheet : 1/1
  • Epson R260 | Service Manual - Page 146
    Model : PM-G850 Stylus Photo R260/R265/R270 Board : C653 PNL Rev. : A Sheet : 1/1
  • Epson R260 | Service Manual - Page 147
    Model : PM-G850 Stylus Photo R260/R265/R270 Board : C653 I/F Rev. : A Sheet : 1/1
  • Epson R260 | Service Manual - Page 148
    Model : PM-D870/PM-G850 Stylus Photo R360/R380/R390 Stylus Photo R260/R265/R270 Board : C653 PSB Rev. : B Sheet : 1/1
  • Epson R260 | Service Manual - Page 149
    Model : PM-D870/PM-G850 Stylus Photo R360/R380/R390 Stylus Photo R260/R265/R270 Board : C653 PSE Rev. : B Sheet : 1/1
  • Epson R260 | Service Manual - Page 150
    Model : PM-D870/PM-G850 Stylus Photo R360/R380/R390 Stylus Photo R260/R265/R270 Board : C653 HEAD Rev. : B Sheet : 1/1
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
EPSON Stylus Photo R260/R265/R270
R360/R380/R390
Color Inkjet Printer
SEIJ06001
SERVICE MANUAL