Epson PS-500 Pulsense Watch Users Guide

Epson PS-500 Pulsense Watch Manual

Get Epson PS-500 Pulsense Watch PDF manuals and user guides View all Epson PS-500 Pulsense Watch manuals
Add to My Manuals
Save this manual to your list of manuals

Epson PS-500 Pulsense Watch manual content summary:

  • Epson PS-500 Pulsense Watch | Users Guide - Page 1
    PS-500 User's Guide
  • Epson PS-500 Pulsense Watch | Users Guide - Page 2
    Thank you for purchasing the PS-500. To use the device, make sure you read the User's Guide and he Quick Start guide. Trademarks EPSON is a registered trademark, EPSON Exceed Your Vision is a registered logomark, and Pulsense is a trademark of Seiko Epson Corporation. Microsoft and Windows are
  • Epson PS-500 Pulsense Watch | Users Guide - Page 3
    application on your PC to upload data (Windows only). Log onto PULSENSE View for iOS or Android on your smart device. Log onto the PULSENSE View web application. Note: To charge the PS-500, a USB port is required. You can use the USB port on a PC or the optional AC adapter. Use only the
  • Epson PS-500 Pulsense Watch | Users Guide - Page 4
    System requirement...2 Contents 4 Using this device safely 6 Symbols in this manual 6 Notes on using the product and components 7 Notes on using the mode 14 Wearing the PS-500 16 Initial configuration ...17 Smart device user 17 PC User...19 Using your PS-500 20 Heart rate measurement
  • Epson PS-500 Pulsense Watch | Users Guide - Page 5
    device 41 About the wristband 41 Replacing the battery 41 Updating the firmware 41 Appendix 42 Product specification 43 Device specifications 43 Cradle specification 43 Troubleshooting 44 Caution ...45 Problem solving ...46 System reset ...47 Where to get help...48 Contents • 5
  • Epson PS-500 Pulsense Watch | Users Guide - Page 6
    not a medical device. Symbols in this manual The following symbols are used in this manual to indicate possible dangerous operations or handling. not do. Ignoring these instructions or mishandling the device could cause malfunction or operational problems. Indicates additional explanations and
  • Epson PS-500 Pulsense Watch | Users Guide - Page 7
    immediately. Do not put it back on. ■ If symptoms persist for more than 2-3 days after removing the Pulsense product, consult a dermatologist. ■ Make sure to follow the wear and care instructions above.Avoid water, sweat or dirt build up between your skin and the product. Clean as directed in
  • Epson PS-500 Pulsense Watch | Users Guide - Page 8
    § 25249.5 and following.) Note: Please note that even if not in use, the PS-500 should be charged at least once within a 6 month period. Failing to do so might device is equipped with Bluetooth® Smart technology. When operating supported heart rate monitors or smart phones, this function wirelessly
  • Epson PS-500 Pulsense Watch | Users Guide - Page 9
    Warning - Removing the verification or certification number for the device Using this device safely • 9
  • Epson PS-500 Pulsense Watch | Users Guide - Page 10
    Set up and basic operation Follow these instructions to use your device: "What's in the box" on page 11 "Operating buttons and functions" on page 12 "Getting Started" on page 14 "Initial configuration" on page 17 Set up and basic operation • 10
  • Epson PS-500 Pulsense Watch | Users Guide - Page 11
    What's in the box PS-500 Cradle Quick Start Guide Options You can purchase the following optional accessories. AC Adapter （E12E204001 [SFAC04]） Set up and basic operation • 11
  • Epson PS-500 Pulsense Watch | Users Guide - Page 12
    the previous screen. Contact point Contact point for charging. LEDs（Blue & Orange） The LEDs on the PS-500 light up or flash to indicate the current heart rate zone. If you set your target in PULSENSE View, you can check your progress when the zone is displayed on the screen. You can cycle
  • Epson PS-500 Pulsense Watch | Users Guide - Page 13
    Icons Battery icon Battery icon Remaining time 20to 36 hours 12to 20 hours 3to 12 hours 0 to 3 hours ! Important Remaining time may vary depending on usage. Bluetooth® icon This product communicates with your smart device via Bluetooth® Smart technology. While the product is connected to the
  • Epson PS-500 Pulsense Watch | Users Guide - Page 14
    it is necessary to register your device with the PULSENSE View web (using the PS Uploader application) or smart device application. Data charged. - Make sure that charging is complete before using your device. 1 Attach the PS-500 to the cradle. 1 Hold the top and bottom of the cradle to open it as
  • Epson PS-500 Pulsense Watch | Users Guide - Page 15
    Some PC USB ports may not support the charging function. 2-2 Using an AC adapter Connect the cradle to the optional AC adapter, then insert the AC adapter into a power outlet. Note: - An orange LED is shown while charging and the LED changes to blue when the PS-500 is fully charged - Charging takes
  • Epson PS-500 Pulsense Watch | Users Guide - Page 16
    of the rechargeable battery. - The battery is not replaceable. Wearing the PS-500 When wearing the product, make sure it does not touch the ulna bone on your wrist. Your Pulsense product is made from materials commonly used in watches and other consumer products. Since you may wear your product over
  • Epson PS-500 Pulsense Watch | Users Guide - Page 17
    install it. Check that "Internet communication" and "Bluetooth®" are enabled in your smart device. Check the operating instructions for your smart device for the configuration method. 2. Start Epson PULSENSE View. Make sure that the product is within three feet (one meter) from the smart device and
  • Epson PS-500 Pulsense Watch | Users Guide - Page 18
    3. Set up your PULSENSE View account by following the on-screen instructions. Once you have created your account and completed your profile, follow the on-screen instructions to pair your PS-500 with your smart device. You see "Complete" on your PS-500 when pairing is successful. Set up and basic
  • Epson PS-500 Pulsense Watch | Users Guide - Page 19
    will open automatically. You can see "PS Uploader" icon in the system tray. "PS Uploader" icon 4 Insert the cradle's USB cable into the USB port of your PC. 5 Go to the "create account screen" and follow the on-screen instructions. You need to set up a PULSENSE View account and follow the on-screen
  • Epson PS-500 Pulsense Watch | Users Guide - Page 20
    Using your PS-500 This product measures heart rate and activity 24 hours a day, tracking your steps, distance, calories, sleep quality, and heart rate across better lifestyle choices. "Heart rate measurement" on page 21 "Menu navigation" on page 29 "Language setting" on page 35 Using your PS-500 • 20
  • Epson PS-500 Pulsense Watch | Users Guide - Page 21
    Heart rate measurement 1 While wearing the product press the [A] button. Heart rate detection starts and a progress bar is displayed. - If the PS-500 cannot detect the heart rate within one minute, the device will vibrate and an error message will be displayed. If the device does not detect
  • Epson PS-500 Pulsense Watch | Users Guide - Page 22
    If the heart rate can't be detected The following vibration (if enabled) and messages are shown when your heart rate can't be detected. Message Description The device is not being worn correctly. The device is not being worn correctly or your skin temperature is too low. Solution Wear the product
  • Epson PS-500 Pulsense Watch | Users Guide - Page 23
    via PULSENSE View to determine when the LEDs illuminate. LED % of max. heart rate 0 - 40% 40 - 70% 70 - 80% 80 - 90% 90 -100% Heart rate zone Below Fat Burning Aerobic Anaerobic Maximum Note: - Your initial heart rate zones are calculated by your profile data. - When wearing the PS-500 overnight
  • Epson PS-500 Pulsense Watch | Users Guide - Page 24
    real-time meter. How your heart rate measurement is being used The PS-500 continuously monitors your heart rate and uses this recording, in addition to your body movement, to calculate the individual activities in PULSENSE View. We therefore recommend having the heart rate detection enabled all the
  • Epson PS-500 Pulsense Watch | Users Guide - Page 25
    Stopping and starting heart rate measurement Manual. 1 To stop measuring your heart rate, press the [A] button. 2 Confirm by pressing the [A] button to return to the previous screen. Automatic. If you remove the PS-500 and no movement is detected, the device will automatically enter sleep mode. • 25
  • Epson PS-500 Pulsense Watch | Users Guide - Page 26
    Display screen in the heart rate measurement mode While in heart rate measurement mode, you can check your real-time heart rate data and statistics on the screen. Press the [B] button to scroll through the screens. Time in fat burning zone. Calories burned. Privacy screen (Displays time and date
  • Epson PS-500 Pulsense Watch | Users Guide - Page 27
    Display screen (without measuring heart rate) When heart rate measurement is disabled, you can check the following measurements on the screens below. Press the [B] button to change the display. Calories burned Time and date Steps Distance calculated by steps • 27
  • Epson PS-500 Pulsense Watch | Users Guide - Page 28
    Backlight Tap the screen of the PS-500 once to turn the backlight on. • 28
  • Epson PS-500 Pulsense Watch | Users Guide - Page 29
    Menu navigation Tap the screen of the PS-500 twice to enter the menu. Navigating the menus Once you are in the menu, press the [B] button to navigate between the sub-menus. Press the [A] button to enter a sub-menu. If you want to return to the time screen, hold the [B] button. • 29
  • Epson PS-500 Pulsense Watch | Users Guide - Page 30
    Zone Menu page on 31 Bluetooth® Menu page on 32 Systems Menu LED Back to "Zone Menu" page on 34 Vibrate Back to "LED" Version page on 35 page on 34 Power OFF page on 34 • 30
  • Epson PS-500 Pulsense Watch | Users Guide - Page 31
    Checking your heart rate range in the fat burning zone You can check which heart rate range you have to be in to enter the fat burning zone in the Zone menu. Press the [A] button once in the [Zone] screen. Go back to the previous screen. • 31
  • Epson PS-500 Pulsense Watch | Users Guide - Page 32
    ® menu by tapping the product once and press the [A] button. 2 Delete the pairing information from PULSENSE View 1 Open PULSENSE View 2 Go to the settings and pairing menu. 3 Delete the PS-500. 3 Delete pairing information from your smart device Go to the Bluetooth® menu of your smart device
  • Epson PS-500 Pulsense Watch | Users Guide - Page 33
    already been deleted from PULSENSE View. 3. The PS-500 already been deleted in the Bluetooth® settings of your smart device. 4. Make sure Bluetooth® communication been enabled on your smart device. 5. Check smart device compatibility:epson.com/PSdevices 6. Ensure your smart device is connected to
  • Epson PS-500 Pulsense Watch | Users Guide - Page 34
    settings Press the [B] button to select ［ON］ or ［OFF］, then press the ［A］ button to set your selection. Power off Turn off PS-500. To turn the PS-500 on again. ・ Press the ［A］ or ［B］ button. ・ Attach the product to the charging cradle. Back to the previous screen. （Hold down [B] ） Note
  • Epson PS-500 Pulsense Watch | Users Guide - Page 35
    Firmware Language setting The following languages are supported: Japanese, English, French, German, and Traditional Chinese. Go to "Settings" > "Regional Settings" in PULSENSE View to select your language. Press the [A] or [B] button to select the settings for your device. • 35
  • Epson PS-500 Pulsense Watch | Users Guide - Page 36
    Other functions "Notification settings" on page 37 "Wake-up alarm" on page 37 " Fitting adjustment" on page 38 Other functions • 36
  • Epson PS-500 Pulsense Watch | Users Guide - Page 37
    in the PULSENSE View app for details. Note: ® The PS-500 must be connected via Bluetooth to your smart device. Some additional settings might be required in the Notifications Settings of your smart device. See your smart device manual for details. Some Android devices may not support this function
  • Epson PS-500 Pulsense Watch | Users Guide - Page 38
    Fitting adjustment The PS-500 has a tool to correctly adjust the strap for optimal heart rate reading. Make sure heart rate sensing is turned off. 1 Wear the product loose, remember
  • Epson PS-500 Pulsense Watch | Users Guide - Page 39
    4 Once the first bar is recorded and "Next" is displayed, tighten the wrist band by one setting and repeat steps 2 and 3. Next 5 Once the measurements are complete, adjust the wrist band to the highest setting for best results. Other functions • 39
  • Epson PS-500 Pulsense Watch | Users Guide - Page 40
    Maintenance "Looking after your device"on page 41 "Replacing the battery" on page 41 "Updating the firmware" on page 41 Maintenance • 40
  • Epson PS-500 Pulsense Watch | Users Guide - Page 41
    Clean the PS-500 regularly. Wipe Updating the firmware You may be able to solve problems that occur by updating the firmware. We recommend epson.com/support/ps500 (U.S.) or epson.ca/support/ps500 (Canada) Before updating the firmware, upload your measurement data using the PULSENSE View app or PS
  • Epson PS-500 Pulsense Watch | Users Guide - Page 42
    Appendix "Product specification" on page 43 Appendix • 42
  • Epson PS-500 Pulsense Watch | Users Guide - Page 43
    3.5 hours (from empty to full) 3 atm Bluetooth® Smart & USB 23°F～104°F/-5℃～+40℃ -4°F～140°F/-20℃～+60℃ Specification 23°F～95°F/-5℃～35℃ Recharge, update PS-500 data through PC. AC adapter Model Input Output Contents Specifications E12E204001 (SFAC04) AC 100-240V 50/60Hz DC 5V / 1.0A Appendix • 43
  • Epson PS-500 Pulsense Watch | Users Guide - Page 44
    Troubleshooting This section explains how to solve problems that occur during use. "Caution" on page 45 "Problem Solving" on page 46 "System reset" on page 47 "Where to get help" on page 48 Troubleshooting • 44
  • Epson PS-500 Pulsense Watch | Users Guide - Page 45
    experience such symptoms: • Stop wearing and remove your Pulsense product immediately. Do not put it back on. • If symptoms persist for more than 2-3 days after removing the Pulsense product, consult a dermatologist. • Make sure to follow the wear and care instructions above. Troubleshooting • 45
  • Epson PS-500 Pulsense Watch | Users Guide - Page 46
    item. Problem Nothing is on the display. Solution Before charging the PS-500, it might be faulty. Immediately stop using the product and cradle, and contact Epson. A charging error is displayed. I wore the product while swimming or diving manual to resolve pairing issues. Troubleshooting • 46
  • Epson PS-500 Pulsense Watch | Users Guide - Page 47
    System reset If device operations become unstable, perform a system reset by connecting the product to the cradle. Charging resets the system, and returns the product to normal operation. If this suggestion does not solve your problem, check "Problem Solving" on page 46. Troubleshooting • 47
  • Epson PS-500 Pulsense Watch | Users Guide - Page 48
    Where to get help Internet support Visit epson.com/support/ps500 (U.S.) or epson.ca/support/ps500 (Canada) for solutions to common problems. You can get tips, usage information, and FAQs, download utilities, view the User's Guide, or e-mail Epson. Telephone support services Call (562) 276-4394
  • Epson PS-500 Pulsense Watch | Users Guide - Page 49
    CPD-42362R1 Troubleshooting • 49
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
PS-500
User’s Guide