Epson LabelWorks LW-400 Users Guide

Epson LabelWorks LW-400 Manual

Get Epson LabelWorks LW-400 PDF manuals and user guides View all Epson LabelWorks LW-400 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson LabelWorks LW-400 manual content summary:

  • Epson LabelWorks LW-400 | Users Guide - Page 1
    batteries 1. Remove the rear cover. Read these instructions before using your product. Button names and functions 20. Cursor keys ( + , + goes to previous or next label) 21. Print ( + feeds the tape) 22. Cut button feed the end of the tape through the tape guide slot. 87 6 1. Font size 2. Font
  • Epson LabelWorks LW-400 | Users Guide - Page 2
    of text. If you try to exceed the maximum, appears and you will not be able to print. Press to delete the and print your label. Adding punctuation There are two groups of available punctuation marks. 1. Press repeatedly to scroll through the available marks. 2. Press to select the desired mark
  • Epson LabelWorks LW-400 | Users Guide - Page 3
    Supported barcode formats: CODE39, CODE128, ITF, CODABAR, UPC-A, UPC-E, EAN-8, EAN-13. • Enter barcodes according to their standards. • Check the created labels moistened with rubbing alcohol, as shown. Troubleshooting Messages Message Problem and solution Insert tape No tape cartridge is Epson.
  • Epson LabelWorks LW-400 | Users Guide - Page 4
    Weight 14 oz (400 g) (excluding batteries, tape (approximate) cartridge) Operating 50 to 95 ºF (10 to 35 ºC) temperature Storage 14 to 131 ºF (-10 to 55 ºC) temperature Epson technical support Visit epson.com/support (U.S.) or epson.ca/support (Canada) where you can view manuals, get FAQs
  • Epson LabelWorks LW-400 | Users Guide - Page 5
    Guide de l'utilisateur Veuillez lire ces instructions avant d'utiliser le produit. Noms et fonctions des boutons S'il reste du ruban excédentaire, alimentez l'extrémité du ruban à travers la fente du guide de ruban. 4. Remettez en place le couvercle et enclenchez-le. Préparation du ruban Après
  • Epson LabelWorks LW-400 | Users Guide - Page 6
    2. Appuyez sur + . 3. Appuyez sur pour confirmer. 4. A ppuyez sur le bouton Couper pour couper le ruban. Avertissement : Appuyez sur le bouton Couper seulement quand le ruban est à l'arrêt, sinon vous risquez d'endommager la cartouche de ruban. Retrait d'une cartouche de ruban 1. Retirez le
  • Epson LabelWorks LW-400 | Users Guide - Page 7
    3. Appuyez sur ou pour sélectionner Activée puis appuyez sur . Création de formats spéciaux Certaines des fonctions de cette section exigent que le format soit sélectionné avant de saisir le texte. Si le système vous le demande, appuyez sur pour supprimer le texte et montrer le menu des é
  • Epson LabelWorks LW-400 | Users Guide - Page 8
    /support où vous pouvez consulter des manuels, une FAQ ou envoyer un courriel à Epson (site Web présenté en anglais seulement). Pour parler à spécialiste de l'assistance technique, composez le (905) 709-2567, de 6 h à 20 h, heure du Pacifique, du lundi au vendredi. Les jours et les heures de service
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Display settings
You can adjust the following display settings:
Backlight:
Turns the backlight of the display on or off.
Contrast:
Adjusts the density of the fonts on the
display. (Value: -5 to +5)
Language:
Changes the language of the settings and
messages on the display.
inch:cm:
Selects the unit of measurement for length.
To adjust display settings, follow the steps below:
1. Press
to turn on the product.
2. Press
+
.
3. Press
or
to highlight a setting, then
press
to select it.
4. Press
or
to select setting options, then
press
.
Setup
This product operates with batteries (not included) or
with an AC adapter (not included).
Inserting batteries
1. Remove the rear cover.
2. Insert 6 AA alkaline batteries.
Note:
If you need to install a tape cartridge, see “Inserting
a tape cartridge” below.
3. Replace the cover and snap it into place.
Optional AC adapter (APT0615Z1-1)
Warning:
Make sure to use AC adapter APT0615Z1-1 or
damage may occur.
1. Plug one end of the AC adapter into the product.
2. Plug the the other end of the AC adapter into the wall
outlet.
Inserting a tape cartridge
1. Remove any slack from the ink ribbon.
2. Remove the rear cover, if necessary.
3. Insert the tape cartridge and press it down firmly until
it snaps into place. If there is excess tape, feed the end
of the tape through the tape guide slot.
4. Replace the cover and snap it into place.
Preparing the tape
After inserting a tape cartridge, make sure to feed
some tape through the tape guide slot to position it
for printing.
1. Press
to turn on the product.
2. Press
+
.
Button names and functions
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
10
1.
Power
2.
Font
3.
Font size
4.
Frame
5.
Font style
6.
Settings
7.
Character keys
8.
Shift key
9.
Caps lock
10. Accent
11. Space
12. Shift key
13. Select/Enter
14. Punctuation
15. Delete (
+
deletes all text)
16. Symbols
17. Special formats
18. Print copies
19.
Preview
20. Cursor keys (
+
,
+
goes to
previous or next label)
21. Print (
+
feeds the tape)
22.
Cut button
23. Display
Turning the power off
Press
to turn off the power. If using an AC adapter,
disconnect it from the wall outlet and the product.
If batteries are inserted, remove them only if the product
will not be used for a long period of time.
Display indicators
Indicators on the display show whether or not settings
are enabled.
1
2
34
5
6
7
8
9
10
11
1.
Font size
2.
Font width
3.
Frame
4.
Font style
5.
Vertical text
6.
Battery level
7.
Accent mark options
8.
Upper/lower case
9.
Cursor (blinks to indicate current position)
10. Line number (appears when multiple lines exist)
Note:
You can print up to four lines of text.
11.
Label number (you can save up to 50 labels)
Read these instructions before using your product.
User’s Guide