Epson ET-2760 Start Here - Installation Guide

Start Here

12

When the message to see the

Start Here

sheet appears

on the LCD screen, press the

OK

button. On the next

screen, press and hold the

help button for 3 seconds.

13

When the message to start initialization appears on the

LCD screen, press the

start button to start charging

the ink. Ink charging takes approximately 10 minutes. A

message appears when ink charging is complete. Press

the

OK

button to continue.

Caution:

Do not turn off the product, raise the scanner unit, or

load paper while the product is charging or you’ll waste ink.

Note:

The included ink bottles are designed for reliable printer

setup and cannot be resold. After setup, the remaining ink is

available for printing.

14

To complete filling the ink tanks, repeat steps 1 through 7

using the remaining ink in the bottles.

Note:

Replace the bottle cap before disposing of the bottles.

15

Close the ink tank cover and scanner unit.

16

Select

Maintenance

>

Reset Ink Levels

, then follow the

on-screen instructions to reset the ink levels.

17

Follow the on-screen instructions to adjust the print

quality. Press the

OK

button to continue.

Note:

•

You need to load paper before you can adjust the print quality. See

“Load paper” on the back of this sheet for details.

•

You can change these settings later using the product’s control

panel. For more information, see the online

User’s Guide

.

IMPORTANT:

Before using this product, make sure you read

these instructions and the safety instructions in the online

User’s

Guide

.

1

Unpack

Note:

Do not open the ink bottles until you are ready to fill the ink

tanks. The ink bottles are vacuum packed to maintain reliability.

1

Remove all protective materials from the product.

2

Lift up the scanner unit. Remove all protective materials

from inside the product.

Caution:

Do not touch the flat white cable or the ink tubes and

their translucent cover.

2

Fill ink tanks

Warning:

Keep the ink bottles out of the reach of children and do not

drink the ink.

Caution:

This product requires careful handling of ink. If ink spills,

wipe it off immediately with a damp towel to avoid permanent stains. If

ink gets on your clothes or belongings, it may not come off.

Note:

• Epson cannot guarantee the quality or reliability of third-party ink.

• Use the ink bottles included with the printer to set up the product.

Part of the ink will be used to charge the print head. These bottles

may print fewer pages compared with replacement ink bottles.

1

Open the ink tank cover, then open the cap for the black

ink tank.

2

Unpack the black (BK) ink bottle. Hold the ink bottle

upright and slowly turn the bottle cap to remove it.

Caution:

Do not shake or squeeze the ink bottles. Do not touch

the top of the ink bottle after its cap is removed.

3

Insert the ink bottle into the filling port, as shown below.

Note:

Refer to the color-coded sticker on the ink tank unit to

identify the color of each tank. Do not force the bottles into

position; they are keyed for each color.

4

Wait for the ink to fill the tank.

Do not squeeze the bottle. Ink

flows into the tank and stops

automatically when the ink is

filled to the upper line.

Note:

If ink does not flow from the

bottle, lift and reinsert the bottle.

Caution:

After setup, periodically

inspect the ink level to ensure it is

not below the lowest line on the tank.

Prolonged use when ink is below

the lowest line could damage the

product. See the online

User’s Guide

for refilling instructions.

5

When the ink tank is full, remove the ink

bottle and replace the bottle cap. Place the

remaining ink aside; you will need it later.

Note:

Do not leave the ink bottle inserted;

otherwise the bottle may be damaged or ink

may leak.

6

Close the ink tank cap.

7

Repeat the previous steps for the other colors.

8

Close the ink tank cover and then the scanner unit.

9

Connect the power cord to the back of the product and to

an electrical outlet.

Caution:

Do not connect to your computer yet.

10

Raise the control panel, then press the

power button to

turn on the product.

Note:

If an error message appears, turn off the product and

check that no protective material has been left inside the product.

11

Press

or

to select your language on the LCD screen,

then press the

OK

button.

Note:

You can change this setting later using the product’s

control panel. For more information, see the online

User’s Guide

.

Follow steps 12 and 13 to continue ink charging.

ET-2760

Epson ET-2760 Start Here - Installation Guide

Epson ET-2760 Manual

Epson ET-2760 manual content summary: