Epson DM-D210 Technical Reference Guide

Epson DM-D210 Manual

Get Epson DM-D210 PDF manuals and user guides View all Epson DM-D210 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson DM-D210 manual content summary:

  • Epson DM-D210 | Technical Reference Guide - Page 1
    Technical Reference Guide Product Overview Describes features and general specifications for this product. Setup Describes how to install and set this product. Handling Describes the basic usage of
  • Epson DM-D210 | Technical Reference Guide - Page 2
    to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.  Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those
  • Epson DM-D210 | Technical Reference Guide - Page 3
    For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. You must follow warnings carefully to avoid
  • Epson DM-D210 | Technical Reference Guide - Page 4
    may lead to fire. Unplug the power cord immediately and contact qualified service personnel for advice.  Do not use aerosol sprayers containing flammable gas Do not connect cables in ways other than those mentioned in this manual. Different connections may cause equipment damage or fire.  Do not
  • Epson DM-D210 | Technical Reference Guide - Page 5
    the development engineers with necessary information for developing, designing, installing the system using DM-D110/DM-D210 as well as for developing and designing the applications. Manual Content The manual is made up of the following sections: Chapter 1 Product Overview Chapter 2 Setup
  • Epson DM-D210 | Technical Reference Guide - Page 6
    ...5 ■ About this Manual ...5 Aim of the Manual ...5 Manual Content ...5 ■ Contents...6 Product Overview 9 ■ Features ...9 ■ Product Structure...10 Customer Display ...10 Accessories ...10 Options ...11 ■ Part Names ...12 DM-D110 ...12 DP-110...12 DM-D110 for TM-T88V-DT ...13 DM-D210 ...14 DP-210
  • Epson DM-D210 | Technical Reference Guide - Page 7
    )...50 DP-502 (TM-U950) ...56 DP-502 (TM-J7200 / TM-J7700) ...59 DP-502 (Attaching on the counter) ...63 DP-503 (TM-H5000II)...66 DM-D110 for TM-T88V-DT ...68 ■ Connecting...74 USB (Self Powered) ...74 USB (Bus Powered)...75 Serial (Stand-Alone)...76 Serial (Pass-through) ...77 Serial
  • Epson DM-D210 | Technical Reference Guide - Page 8
    Print XML...84 ESC/POS ...84 ■ Software and Manuals ...85 Development Kits ...85 Drivers ...86 Manuals ...86 Download ...86 ■ Data flow of serial (USB controlled 91 Appendix...92 ■ Product Specifications ...92 DM-D110 ...92 DM-D210 ...96 Environmental Conditions...98 ■ DP-110/DP-210 Connector
  • Epson DM-D210 | Technical Reference Guide - Page 9
    allow long service life, wide view angle, and clear visibility in bright places and dark places.  DM-D110 is compact.  DM-D210 has easy-to or a USB interface. The USB-RS232 conversion driver recognizes USB connection as a virtual serial port.  DM-D110 supports USB bus power.  You can connect a
  • Epson DM-D210 | Technical Reference Guide - Page 10
    TM-T88V-DT model (For TM-T88V-DT) DM-D210  RS-232/USB model  RS-232 model Accessories Model RS-232/USB model RS-232 model USB model DM-D110 for TM-T88V-DT Accessory  Start Here  Manual CD  Ferrite core  Cap User's Manual User's Manual The following items are supplied depending on when the
  • Epson DM-D210 | Technical Reference Guide - Page 11
    (with an interface board) DP-110 without Interface Board DM-D110 stand (without an interface board) Use this when installing near the USB bus power and the printer using a Y-type connection. DP-105 Extension pole to be used with DP-110 DM-D210 DP-210 DM-D210 stand (with interface board) 11
  • Epson DM-D210 | Technical Reference Guide - Page 12
    Part Names DM-D110 Screen Dip switch (rear side) Power Switch *1 (bottom side of the display) Chapter 1 Power supply connector Extension power cable connector Plate Computer interface connector JP2 DM-D connector JP1 Printer interface  connector Interface board (Not attached to DP-110
  • Epson DM-D210 | Technical Reference Guide - Page 13
    DM-D110 for TM-T88V-DT Ferrite core * Chapter 1 Product Overview Screen Dip switch (rear side) Base Straight pole 1 L-shaped pole USB cable (with a cap *)  They may not be supplied for DM-D110 for TM-T88V-DT depending on when the product is shipped. 13
  • Epson DM-D210 | Technical Reference Guide - Page 14
    DM-D210 Screen Chapter 1 Product Overview Power Switch (bottom side of the display) Dip cable, RS-232 cable cap and ferrite core are not included. DP-210 DM-D connector Power supply connector Computer interface connector Extension power cable connector Printer interface connector JP1 JP2
  • Epson DM-D210 | Technical Reference Guide - Page 15
    product. USB (Self Powered) Connect this product's USB cable to the computer, and then connect the RS-232 cable to DP-110/DP-210. Computer DM-D110/DM-D210 1 PS-180 USB USB (Bus Powered): Computer Connect this product's USB cable to the computer. Power is supplied from the computer. Computer
  • Epson DM-D210 | Technical Reference Guide - Page 16
    supplied from the TM intelligent printer. TM-T88V-DT (Attach DM-D110 for TM-T88V-DT) TM-T88V-DT DM-D110 for TM-T88V-DT 1 USB TM-DT series/TM-i series TM Intelligent Printer DM-D110 USB DM-D110: You can use the RS-232/USB and USB models. DM-D210: You cannot use it. 16
  • Epson DM-D210 | Technical Reference Guide - Page 17
    Chapter 1 Product Overview Serial (Stand-Alone) Connect DP-110/DP-210 to the computer using a serial cable. Computer DM-D110/DM-D210 Serial PS-180 1 Serial (Pass-through) Connect the serial interface TM printer to the DP-110/DP210 connected to the computer using a serial connection. The
  • Epson DM-D210 | Technical Reference Guide - Page 18
    Chapter 1 Product Overview Serial (Y-type) Connect this product's RS-232 cable to the TM printer DM-D connector, and then connect the TM printer and the computer using a serial cable. Power is supplied from the TM printer. TM Printer DM-D110/DM-D210 Computer Serial RS-232 1 PS-180 18
  • Epson DM-D210 | Technical Reference Guide - Page 19
    is supplied from the TM printer. TM Printer Computer 1 UB-U01III/ USB UB-U02III PS-180 RS-232 DM-D110/DM-D210 Serial (USB/Ethernet controlled) Connect this product's RS-232 cable to the DM-D connector of the TM printer, and then connect the TM printer and computer by using a USB cable or
  • Epson DM-D210 | Technical Reference Guide - Page 20
    (Pass-through) ✔ - - - Serial (Y-type) ✔ ✔ ✔ ✔ Serial (USB controlled) ✔ ✔ ✔ ✔ Serial (USB/Ethernet controlled) - - ✔ -  Attached to TM-H6000IV-DT DM-D210 Connection Pattern USB (Self Powered) Serial (Stand-Alone) Serial (Pass-through) Serial (Y-type) Serial (USB controlled
  • Epson DM-D210 | Technical Reference Guide - Page 21
    to 115200 bps. Attaching the Product (page 30) Connecting Cables (page 74) Installing the DM-D110 Virtual COM Port Driver to the Computer For details, see the manual supplied with the DM-D110 Virtual COM Port Driver.  When extending the length of the support, prepare the option of DP-105. 21
  • Epson DM-D210 | Technical Reference Guide - Page 22
    , see the manual supplied with the DM-D110 Virtual COM Port Driver. For the TM-i series host, you do not need the DM-D110 Virtual COM Port Driver. For the TM-DT series host, the DM-D110 Virtual COM Port Driver is already installed.  When extending the length of the support, prepare the option
  • Epson DM-D210 | Technical Reference Guide - Page 23
    cable (page 105) Dip Switch Settings (page 27) Attaching the Product (page 30) Connecting Cables (page 76)  When extending the length of the support, prepare the option of DP-105. Serial (Pass-through) Preparation  Option (DP-110 */DP-210)  AC adapter  Power cord  TM Printer (Serial interface
  • Epson DM-D210 | Technical Reference Guide - Page 24
    503  DM-D210: Select from the following options  DP-210  DP-502  DP-503  TM Printer (with DM-D connector, Serial interface)  AC adapter  Power cord Dip Switch Settings (page 27) Attaching the Product (page 30) Connecting Cables (page 78)  When extending the length of the support, prepare the
  • Epson DM-D210 | Technical Reference Guide - Page 25
    : Select from the following options  DP-110 *  DP-502  DP-503  DM-D210: Select from the following options  DP-210  DP-502  DP-503  TM Printer (with Product (page 30) Connecting Cables (page 79)  When extending the length of the support, prepare the option of DP-105. Chapter 2 Setup 2 25
  • Epson DM-D210 | Technical Reference Guide - Page 26
    Serial (USB/Ethernet controlled) Preparation  DM-D110  DP-502  DM-D210  DP-502  TM Printer  AC adapter  Power cord Dip Switch Settings (page 27) Set the communication speed to 19200 bps. Attaching the Product (page 30) Connecting Cables (page 80) Chapter 2 Setup 2 26
  • Epson DM-D210 | Technical Reference Guide - Page 27
    ) Set the communication speed to 19200 bps. TM Intelligent Printer (ePOS-Device) Match the serial communication settings for the TM intelligent printer's EPSON TMNet WebConfig and this product. TM-DT Series (Windows) Match the serial communication settings for the TM-DT Series and this product
  • Epson DM-D210 | Technical Reference Guide - Page 28
    may damage the device. 1 Turn off the power of the this product and system, and remove cable. 2 Remove the DIP switch cover. DM-D110 DM-D210 ON 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 2 DIP Switch Cover 3 Change each setting of the switches Refer to "DIP Switch 1 Functions" on page 29 for
  • Epson DM-D210 | Technical Reference Guide - Page 29
    Chapter 2 Setup DIP Switch 1 Functions The following explains the DIP switch functions. DSW1 No. Function ON OFF 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 *2 1-10 *2 Received Error Data Ignore Receive Data Length Parity Parity Selection Communication Speed Switching Execute Self-Test *1 Not used
  • Epson DM-D210 | Technical Reference Guide - Page 30
    DP-502 to attach DM-D110/DM-D210 to TM-U950. page 56 DP-503 Use the optional DP-502 to attach DM-D110/DM-D210 to TM-J7200/ TM-J7700. page 59 Use the optional DP-502 to attach DM-D110/DM-D210 to the counter. Use the optional DP-503 to attach DM-D110/DM-D210 to TM-H5000II. page
  • Epson DM-D210 | Technical Reference Guide - Page 31
    DP-110 Checking the accessories Check the DP-110 parts. Chapter 2 Setup DP-110 Plate 2 Extension power cable Checking the accessories of DP-105 Check the DP-105 parts. RS-232C connector installation screw (millimeter type) Affixing tapes Extension support 31
  • Epson DM-D210 | Technical Reference Guide - Page 32
    Chapter 2 Setup Setting the DP-110 Connector installation screw Inch-type hexagonal lock screws are installed in the connector for serial cable connection of DP-110.  If millimeter-type lock screws are needed, use the millimeter-type lock screws of the accessory. Notch (one or more lines) inch-
  • Epson DM-D210 | Technical Reference Guide - Page 33
    have 1 cable. 1 Pass the cable for the DM-D110 through the DP-110. When extending the length of the DP110, attach the extension support (DP-105) to the DP-110. When using the extension  support (DP-105) 2 2 Insert the tab on the DM-D110 (or the extension support) into the hole on the DP-110
  • Epson DM-D210 | Technical Reference Guide - Page 34
    push the base plate until it is locked by the hook on the DP-110. The plate is locked  by the hook. 6 When the extension support (DP-105) is used, attach affixing tapes to the four  corners of the plate to keep the unit from falling down. 7 When using the AC
  • Epson DM-D210 | Technical Reference Guide - Page 35
    DP-210 Checking the accessories Check the DP-210 parts. Chapter 2 Setup DP-210 Support Extension support 2 Extension power cable RS-232C connector installation screw (millimeter type) Setting the DP-210 Connector installation screw Inch-type hexagonal lock screws are installed in
  • Epson DM-D210 | Technical Reference Guide - Page 36
    have 1 cable. 1 Pass the cable for the DM-D210 through the support. When using the extension support, insert the tab on it into the hole on support until you feel it click. 2 When using the extension support 2 Insert the tab on the support (or the extension support) into the hole on the DP-210
  • Epson DM-D210 | Technical Reference Guide - Page 37
    Chapter 2 Setup 3 Connect the cable to DP-210, computer, and TM printer to match the constructed environment. (See "Connecting" on page 74) 4 Arrange the cables as shown below. Put the cables inside the DP-210. For the RS-232/USB model, the end of the connector of the unused cable should be capped,
  • Epson DM-D210 | Technical Reference Guide - Page 38
    used. Checking the accessories Check the DP-502 parts. When attaching to the TM-H6000V, use the following parts. Stopper Fixing screw Angle fixing Installation Guide Fixing plate B 2 for stopper screw Fixing screws for rubber feet (small) Rubber feet (small) Fixing screws for fixing plate
  • Epson DM-D210 | Technical Reference Guide - Page 39
    to the TM-H6000V The illustrations used here are for DM-D210, but you can still use them as your reference  for DM-D110. 1 Turn the printer over. 2 Attach the rubber feet to the printer. 2 3 Pass the cable for the this product through support C, and attach support C to the this product. When using
  • Epson DM-D210 | Technical Reference Guide - Page 40
    for the this product through the hole on fixing plate A.  Do not pass the USB cable through fixing plate A as it is later stored in support C. For USB Cable 2 5 Hook the cable to the tab of fixing plate A and secure. 6 Install the ferrite core to the RS-232 cable of the
  • Epson DM-D210 | Technical Reference Guide - Page 41
    7 Attach fixing plate B to the printer. Chapter 2 Setup 2 8 Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the stopper into the holes of fixing plate B. Fixing plate A can be attached on either side of the printer. (The
  • Epson DM-D210 | Technical Reference Guide - Page 42
    Chapter 2 Setup 9 The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw.  The roll paper cover and receipt unit may not open if the
  • Epson DM-D210 | Technical Reference Guide - Page 43
    Chapter 2 Setup 10Turn the printer over to the normal status. 11Place a cap on the USB cable to store in the pole. Store the rest of RS-232 cable in the pole, and then install the customer display to fixing plate A. 2 43
  • Epson DM-D210 | Technical Reference Guide - Page 44
    parts. Stopper Fixing screw for stopper Angle fixing screw Fixing plate B Fixing screws for rubber feet (small) 2 Rubber feet (small) Fixing screws for fixing plate B Support C Support B for extension Fixing plate A 44
  • Epson DM-D210 | Technical Reference Guide - Page 45
    , but you can still use them as your reference for DM-D210.  Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable. 1 Pass the cable for the this product through support C, and attach support C to the this product. When using
  • Epson DM-D210 | Technical Reference Guide - Page 46
    . For the RS-232/USB model, the end of the connector of the unused cable should be 2 capped, and then bundled to be stored inside support. 46
  • Epson DM-D210 | Technical Reference Guide - Page 47
    Chapter 2 Setup 5 Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the stopper into the holes of fixing plate B. Fixing plate A can be attached on either side of the printer. (The illustration below shows fixing plate A attached to the
  • Epson DM-D210 | Technical Reference Guide - Page 48
    Chapter 2 Setup 6 The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw. The paper roll cover may not open if the position of the display
  • Epson DM-D210 | Technical Reference Guide - Page 49
    Chapter 2 Setup 7 Store any excess cable in the support and attach the this product to fixing plate A. 8 Connect the DC cable to the printer. To avoid disconnection, hook the cable on the tabs on fixing plate B, as shown below. 2 49
  • Epson DM-D210 | Technical Reference Guide - Page 50
    attaching to the TM-H6000IV-DT, use the following parts. Stopper Fixing screw for stopper Angle fixing screw Fixing plate B 2 Fixing screws for fixing plate B Support C Support B for extension Fixing plate A 50
  • Epson DM-D210 | Technical Reference Guide - Page 51
    Chapter 2 Setup Installing to the TM-H6000IV-DT Follow the instructions to install the DM-D110 (USB model) on the TM-H6000IV-DT using the exclusive DP502. Because the illustration used here is for the RS-232/USB model, there
  • Epson DM-D210 | Technical Reference Guide - Page 52
    Chapter 2 Setup 3 Use the 2 screws removed in Step 2 and the 2 included long screws. Be sure not to connect the cables before attaching the plate. Otherwise, the cables can be damaged. 2 4 The illustration shows how to install this product on the right side of the TMH6000IV-DT. If you install it on
  • Epson DM-D210 | Technical Reference Guide - Page 53
    Chapter 2 Setup 5 Select the position where the this product is to be installed from A, B, C, or D. 2 53
  • Epson DM-D210 | Technical Reference Guide - Page 54
    Chapter 2 Setup 6 Move the attached part in Step 4 so that screw holes indicated in the illustration are aligned with each other, according to the position you selected. Fix it with the included screw. 7 Use the included support B for extension if the support C is not long enough. 2 54
  • Epson DM-D210 | Technical Reference Guide - Page 55
    Chapter 2 Setup 8 Put the USB cable through behind TM-H6000IV-DT as shown in the illustration. 2 9 Install this product to the Fixing Plate A. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then bundled to be stored inside support. 55
  • Epson DM-D210 | Technical Reference Guide - Page 56
    DP-502 (TM-U950) Checking the accessories Check the DP-502 parts. When attaching to the TM-U950, use the following parts. Chapter 2 Setup Rubber feet (square) Fixing screws for plastic position Fixing plate A Support C 2 Support B for extension 56
  • Epson DM-D210 | Technical Reference Guide - Page 57
    , but you can still use them as your reference for DM-D210.  Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable. 1 Pass the cable for the this product through support C and attach support C to the this product. When using
  • Epson DM-D210 | Technical Reference Guide - Page 58
    bottom as shown below. 2 4 Adjust the length of the cable and secure fixing plate A to the printer with screws. 5 Store any excess cable in the support, and attach the this product to fixing plate A. For the RS-232/USB model, the end of the connector of the unused cable should be
  • Epson DM-D210 | Technical Reference Guide - Page 59
    . Chapter 2 Setup 2 Checking the accessories Check the DP-502 parts. When attaching to the TM-J7200 and TM-J7700, use the following parts. Fixing plate A Support C Support B for extension Fixing screws for plastic position 59
  • Epson DM-D210 | Technical Reference Guide - Page 60
    , but you can still use them as your reference for DM-D210.  Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable. 1 Pass the cable for the this product through support C and attach support C to the this product. When using
  • Epson DM-D210 | Technical Reference Guide - Page 61
    2 Setup 3 Turn the printer over. 4 When installing the AC adapter to the base of TM-J7700, see the "TM-J7200/TMJ7700 Technical Reference Guide" for procedures and notes regarding installation. When installing a customer display to the AC adapter side, do not use the power source fixing plate and
  • Epson DM-D210 | Technical Reference Guide - Page 62
    Chapter 2 Setup 6 Install the ferrite core to the RS-232 cable of the customer's display, remove the cap, and connect the cable to the printer's DM-D connector. 7 Hook the cable to the tab of fixing plate A and secure. 2 8 Turn the printer over to the normal status. 9 Place a cap on the USB
  • Epson DM-D210 | Technical Reference Guide - Page 63
    DP-502 (Attaching on the counter) Checking the accessories Check the DP-502 parts. When attaching it on the counter, use the following parts. [DP-502 parts] Chapter 2 Setup Affixing tapes Affixing tapes Fixing screws for wood position 2 Fixing plate A Support C Support B for extension 63
  • Epson DM-D210 | Technical Reference Guide - Page 64
     The illustrations used here are for DM-D110, but you can still use them as your reference for DM-D210.  Because the illustration used here is through support C and attach support C to the this product. When using support B for extension, insert the tab on support B into the hole on support C
  • Epson DM-D210 | Technical Reference Guide - Page 65
    to the mounting position. 5 Connect the cable to the TM printer. When the cable is long, put the excess part of the cable in the support. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then bundled to be stored inside
  • Epson DM-D210 | Technical Reference Guide - Page 66
    , use the following parts. [DP-503 parts] Base Fixing screws Support C Support B for extension 2 Installing to the TM-H5000II  The illustrations used here are for DM-D110, but you can still use them as your reference for DM-D210.  Because the illustration used here is for the RS-232/USB
  • Epson DM-D210 | Technical Reference Guide - Page 67
    it with the screws. 3 Pass the cable for the this product through the base. 2 4 Insert the tab on the base into the hole on the support until you feel it click. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then
  • Epson DM-D210 | Technical Reference Guide - Page 68
    -D110 for TM-T88V-DT Checking the accessories Check the accessories of the DM-D110 for TM-T88V-DT. When attaching it on the printer, use the following parts. For models with a L-shaped pole 2 Customer display Base Screws For
  • Epson DM-D210 | Technical Reference Guide - Page 69
    Chapter 2 Setup Attaching to the DM-D110 for TM-T88V-DT For models with a L-shaped pole 1 Detach the connector cover of the TM-T88V-DT. Detach the hooks from the TM-
  • Epson DM-D210 | Technical Reference Guide - Page 70
    4 Pass the USB cable of the customer display through the base. Chapter 2 Setup 2 5 Align the dowel hole in the customer display and the dowel on the base to attach the customer display on the base. 6 Align the hook for the connector cover of TM-T88V-DT with the groove on the back of TM-T88V-DT,
  • Epson DM-D210 | Technical Reference Guide - Page 71
    Chapter 2 Setup For models with a straight pole 1 Detach the connector cover of the TM-T88V-DT. Detach the hooks from the TM-T88V-DT while pushing the bottom parts on both sides of the connector cover inwards. 2 Remove the U-shaped component from the connector cover. 2 3 Attach the base on the TM
  • Epson DM-D210 | Technical Reference Guide - Page 72
    Chapter 2 Setup 4 With the end of the straight pole with a hole pointing downward, pass the USB cable of the customer display through the pole and base. 2 5 Attach the pole with the customer display. 72
  • Epson DM-D210 | Technical Reference Guide - Page 73
    Chapter 2 Setup 6 Align the dowel hole in the pole and the dowel on the base to attach the pole on the base. 7 Align the hook for the connector cover of TM-T88V-DT with the groove on the back of TM-T88V-DT, and then push it in. 2 When attaching the connector cover, always hold both sides.
  • Epson DM-D210 | Technical Reference Guide - Page 74
    sure you hold the connector part. If you pull the cable part, you may damage the cable. USB (Self Powered) 2 DM-D110/DM-D210 Ferrite core USB cable RS-232 cable  DM-D110  DM-D210  DP-110  DP-210 Computer AC adapter Power cord DP-110/DP-210 USB cable  Remove the cap  Attach the
  • Epson DM-D210 | Technical Reference Guide - Page 75
    connected Chapter 2 Setup Computer/ TM Intelligent Printer DP-110 2 DM-D110 USB cable  Remove the cap *1  Attach the *2  Attach the ferrite core *2  Connect to the TM-T88V-DT DP-110 DM-D connector Not used Power supply connector Not used Extension power cable connec- Not used tor
  • Epson DM-D210 | Technical Reference Guide - Page 76
    core USB cable Cap RS-232 cable JP 2-3 Serial cable AC adapter Computer Power cord DP-110/DP-210 2  DM-D110 USB cable *  Do not remove the cap (factory default condition)  DM-D210  Not used (bundle inside DP-110/DP-210) RS-232 cable  Remove the cap *  Attach the ferrite core
  • Epson DM-D210 | Technical Reference Guide - Page 77
    cable Cap RS-232 cable JP 1-2 Serial cable Computer Serial cable AC adapter Power cord Extension power cable DP-110/DP-210 2 TM Printer  DM-D110  DM-D210 USB cable *  Do not remove the cap (factory default condition)  Not used (bundle inside DP-110/DP-210) RS-232 cable  Remove the
  • Epson DM-D210 | Technical Reference Guide - Page 78
    core USB cable Cap RS-232 cable Not connected AC adapter Serial cable Computer DP-110/DP-210 Power cord TM Printer 2  DM-D110  DM-D210  DP-110  DP-210 USB cable * RS-232 cable  Do not remove the cap (factory default condition)  Not used (bundle inside DP-110/DP-210
  • Epson DM-D210 | Technical Reference Guide - Page 79
    core USB cable Cap Not connected AC adapter RS-232 cable USB cable Computer DP-110/DP-210 Power cord TM Printer 2  DM-D110  DM-D210 USB cable * RS-232 cable  Do not remove the cap (factory default condition)  Not used (bundle inside DP-110/DP-210 or DP-502/DP-
  • Epson DM-D210 | Technical Reference Guide - Page 80
    core USB cable Cap RS-232 cable AC adapter USB cable Ethernet Computer Power cord 2 TM Printer  DM-D110  DM-D210 USB cable * RS-232 cable  Do not remove the cap (factory default condition)  Not used (bundle inside DP-502)  Remove the cap *  Attach the ferrite
  • Epson DM-D210 | Technical Reference Guide - Page 81
    . In these situations, remove the customer display and base unit, then adjust the position of the lug in the base unit before reattaching. DM-D110 90 48 3 DM-D110 for TM-T88V-DT You can change the direction or angle of the display and L-shaped pole by moving them while holding TMT88V
  • Epson DM-D210 | Technical Reference Guide - Page 82
    Chapter 3 Handling Cleaning the customer display Turn off the this product as well as the connected system. Use a dry cloth or firmly wrung cloth to wipe off any stains on the this product. Do not use alcohol, benzine, thinner and other solvents; otherwise, the product may be damaged or the plastic
  • Epson DM-D210 | Technical Reference Guide - Page 83
    message in XML format and sends it to printer using socket communications. For detailed information about ePOS-Device XML, see the ePOS-Device XML User's Manual. Customer display  DM-D110  DM-D210 *  Only for TM-H6000V. TM printer  TM-i series  TM-DT series  TM-T88VI-iHUB  TM-H6000V 83
  • Epson DM-D210 | Technical Reference Guide - Page 84
    information about ePOS-Print XML, see the ePOS-Print XML User's Manual. Customer display  DM-D110  DM-D210 *  Only for TM-H6000V. TM printer  TM-T88VI  TM-T88VI-iHUB  TM-H6000V ESC/POS ESC/POS is the Epson original printer command system for POS printers and customer display. With ESC
  • Epson DM-D210 | Technical Reference Guide - Page 85
    display from the Web application or native application for smart devices. It includes libraries, manuals, and sample programs. for Universal Windows apps for JavaScript EPSON OPOS ADK OCX driver that controls the POS peripheral devices such as the customer display using the OLE technologies
  • Epson DM-D210 | Technical Reference Guide - Page 86
    connected to the USB as a virtual serial port. This driver is already installed in the TM intelligent printer's TM-DT series. Windows Manuals Software Description DM-D110/DM-D210  Technical Reference Guide This manual. Each TM printer's Technical Refer- TM printer's Technical Reference
  • Epson DM-D210 | Technical Reference Guide - Page 87
    Information Data flow of serial commands This section explains the data flow when using this product using a serial connection. Block Diagram DM-D110/DM-D210 CPU for display unit Level shifter RS-232 cable connector Modular-8 Printer interface connector D-Sub 9 (Male) TXD DSR DTR RXD Computer
  • Epson DM-D210 | Technical Reference Guide - Page 88
    printer, connect it to another port of the computer. The data flow when the standalone connection is as follows. Computer DP-110/DP-210 DM-D110 DM-D210 Power supply Transmit data from the computer Transmit data to the computer  When 2-3 of JP1 and JP2 are selected, the data from the computer
  • Epson DM-D210 | Technical Reference Guide - Page 89
    printer to one serial port of the computer. The data flow when the pass-through connection is as follows. Computer DP-110/DP-210 DM-D110 DM-D210 TM Printer Power supply Transmit data from the computer Transmit data to the computer from the TM printer Transmit data to the TM printer  With
  • Epson DM-D210 | Technical Reference Guide - Page 90
    follows. Computer Transmit data from the computer Transmit data to the computer from the TM printer Transmit data to the TM printer TM Printer DM-D110 DM-D210 Power supply  The data from the computer is transmitted to the TM printer and the same data is transmitted to the cus- tomer display
  • Epson DM-D210 | Technical Reference Guide - Page 91
    using a USB connection (self powered and bus powered). Controlled environment Precautions EPSON OPOS ADK EPSON OPOS ADK for .NET EPSON JavaPOS ADK EPSON Advanced Printer Driver When using the DM-D110 Virtual COM Port Driver, set the communication speed for the dip switch to 115200 bps. Before
  • Epson DM-D210 | Technical Reference Guide - Page 92
    USB RS-232 Standard Connector USB Standard Connector Reliability Power  supply voltage * RS-232/USB RS-232 USB Power consumption DM-D110 DM-D110 with DP-110 DM-D110 for TM-T88V-DT Fluorescent tube display 40 characters (20 columns x 2 rows, 5 x 7 dot matrix) Green (505 nm) 690 cd
  • Epson DM-D210 | Technical Reference Guide - Page 93
    Appendix Model Tilt angle Horizontal rotation angle DM-D110 DM-D110 with DP-110 Maximum 48 (4 steps, 5 positions) Maximum 90 - Power supply Supplied by TM printer PS-180 (Option) or USB bus  It differs according to the product models. DM-D110 for TM-T88V-DT  Display:  Maximum 300  L-
  • Epson DM-D210 | Technical Reference Guide - Page 94
    Mass Specification 165 (W) x 50.5 (D) x 69 (H) mm {6.5 (W) x 1.99 (D) x 2.72" (H)} 165 (W) x 50.5 (D) x 69 (H) mm {6.5 (W) x 1.99 (D) x 2.72" (H)} Approximately 0.29 kg {Approximately 0.64 lb} DM-D110 with DP-110 50.5 mm 135 mm 63 mm 69 mm Item Display unit dimension Base unit dimension External
  • Epson DM-D210 | Technical Reference Guide - Page 95
    69 mm Item Display unit dimension TM-T88V-DT dimension (with a L-shaped pole) TM-T88V-DT dimension (with a straight pole) Mass DM-D110 with DP-502 Specification 177 (W) x 70 (D) x 69 (H) mm {6.97 (W) x 2.76 (D) x 2.72" (H)} 177 (W) x 362 (D) x 202 (H) mm {6.97 (W) x 14.25 (D) x 7.95" (H)} 177
  • Epson DM-D210 | Technical Reference Guide - Page 96
    Appendix DM-D210 Model DM-D210 DM-D210 with DP-210 Display type Number of characters displayed Display color Brightness Character classes Character composition Character size Character pitch Interface * RS-232/USB Standard
  • Epson DM-D210 | Technical Reference Guide - Page 97
    60 mm 260 mm Appendix 83 mm Item Display unit dimension External dimensions Mass DM-D210 with DP-210 Specification 260 (W) x 60 (D) x 83 (H) mm {10.24 (W) x 2.36 (D) x 3.27" (H)} 260 (W) x 60 (D) x 83 (H) mm {10.24 (W) x 2.36 (D) x 3.27" (H)} Approximately 0.60 kg {Approximately 1.32
  • Epson DM-D210 | Technical Reference Guide - Page 98
    mm {10.24 (W) x 6.46 (D) x 14.17 or 18.9" (H)} 78 (W) x 164 (D) x 260 (H) mm {3.12 (W) x 6.56 (D) x 10.4" (H)} Approximately 0.55 kg {Approximately 1.21 lb} DM-D210 with DP-503 Item Display unit dimension External dimensions DP-503 Mass Specification 260 (W) x 60 (D) x 83 (H) mm {10.24 (W) x 2.36
  • Epson DM-D210 | Technical Reference Guide - Page 99
    DP-110/DP-210 Connector Specifications This section explains the DP-110/DP-210 connector specifications. Computer Interface Connector (Serial) Type: D-Sub 25-pin connector 14 25 Appendix 1 13 Pin assignments Pin Signal Number Name 1 FG 2 TXD 3 RXD 4 *1 RTS 6 *2 DSR 7 GND
  • Epson DM-D210 | Technical Reference Guide - Page 100
    the DTR terminal of the TM printer directly. 1 Make sure to use either the RTS or the DTR terminal. Otherwise, the built-in RS-232 driver IC may be broken. 2 This signal is connected to the DTR terminal of the TM printer directly. 100
  • Epson DM-D210 | Technical Reference Guide - Page 101
    cannot receive data. If the TM printer becomes ready to receive data, MARK is not output. Output Reset signal to the printer. (Computer -> TM Printer) 101
  • Epson DM-D210 | Technical Reference Guide - Page 102
    Printer Interface Connector (Serial): DP-210 Type: D-Sub 25-pin connector 13 1 Appendix 2 14 Pin assignments Pin Signal Number Name 1 FG 2 TXD 3 RXD 6 DSR 7 GND 20 DTR 25 RESET Signal Direction Function - Frame ground Output Receive data from the TM printer. (TM Printer
  • Epson DM-D210 | Technical Reference Guide - Page 103
    DM-D Connector (RS-232) Type: RJ-45 Connector 1 8 Appendix Pin assignments Pin Signal Number Name 1 FG 2 TXD 3 RXD 4 DSR 5 RTS 6 SG 7 PS 8 PG Signal Direction Function -
  • Epson DM-D210 | Technical Reference Guide - Page 104
    Power Supply Connector/Extension power cable connector Type: 3-pin locking type connector Appendix Pin assignments Pin Signal Number Name 1 +24V 2 GND 3 NC SHELL FG Signal Direction - Power supply line - GND - Not used - Frame ground Function 104
  • Epson DM-D210 | Technical Reference Guide - Page 105
    -DSR), use the serial cable that has the following wiring. DM-D110 Connection pattern Type of serial cable Stand-Alone D-Sub 9- Connect the DP-110 to the TM printer Connect the computer to the TM printer DM-D210 Connection pattern Type of serial cable Stand-Alone D-Sub 9-pin (female) /D-Sub
  • Epson DM-D210 | Technical Reference Guide - Page 106
    Wiring D-Sub 9-pin (female) D-Sub 25-pin (male) D-Sub 25-pin (male) D-Sub 25-pin (male) Appendix 106
  • Epson DM-D210 | Technical Reference Guide - Page 107
    Character Code Tables Refer to the following URL regarding the character code table. https://reference.epson-biz.com/pos/reference/charcode_dm_d_en/ Appendix 107
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Technical Reference Guide
Describes features and general speciļ¬cations for this
product.
Describes how to install and set this product.
Describes the basic usage of this product.
Describes how to control this product and information
necessary for developing applications.
Describes the speciļ¬cations of the product, connectors,
and serial cables, as well as the character code table.
M00035603
Rev. D
Appendix
Application Development Information
Handling
Setup
Product Overview