Epson C32C824151 Technical Reference

Epson C32C824151 - UB E02 Print Server Manual

Get Epson C32C824151 - UB E02 Print Server PDF manuals and user guides
UPC - 000054074415
View all Epson C32C824151 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson C32C824151 manual content summary:

  • Epson C32C824151 | Technical Reference - Page 1
    UB-E02 Technical Reference Guide 10Base-T/100Base-TX Ethernet Interface board EPSON English 404999000
  • Epson C32C824151 | Technical Reference - Page 2
  • Epson C32C824151 | Technical Reference - Page 3
    UB-E02 Technical Reference Guide CAUTIONS ❏ This document shall apply only to the product(s) identified to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. ❏ Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of
  • Epson C32C824151 | Technical Reference - Page 4
    Revision Information Revision Rev. A Page Altered Items and Contents ii Rev. A
  • Epson C32C824151 | Technical Reference - Page 5
    Includes practical programming information. Chapter 5, "Specification" Gives specifications. Appendix A, "Definitions" Provides definitions of terms used in this guide. Related Documents Software/document name UB-E02 User's Manual Description Provides instructions for operators of POS systems
  • Epson C32C824151 | Technical Reference - Page 6
    applied only to the interface boards that are so labeled. (EMC is tested using the EPSON PS-170 power supply and TM series printers.) Europe: North America: Japan: Oceania: if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
  • Epson C32C824151 | Technical Reference - Page 7
    ISO 7779). Key to Symbols The following symbols are used in the documentation for this product. See the specific warnings and cautions at appropriate points throughout this guide. WARNING: Warnings must be followed carefully to avoid serious bodily injury. CAUTION: Cautions must be observed to avoid
  • Epson C32C824151 | Technical Reference - Page 8
    product should only be connected to the devices specified in this guide. Connecting other devices could cause damage, fire or explosion. ❏ display module connector or the drawer kick-out connector." Product Servicing This product cannot be serviced at the component level. If damage occurs, the UB-E02
  • Epson C32C824151 | Technical Reference - Page 9
    Windows® 95, Windows® 98 Second Edition, Windows® 2000 Professional, and Windows®XP Professional ❏ Windows NT® 4.0 Supported Protocols ❏ TCP/IP Environments for Setup Utility ❏ EPSON TMNet WinConfig applies to the following versions of Windows: • Windows 95 • Windows 98 Second Edition • Windows 2000
  • Epson C32C824151 | Technical Reference - Page 10
    Supported TM Printers The following printers can use the UB-E02. (The TM-J8000, TM-T285, and RP-U420 cannot use the UB-E02. For new
  • Epson C32C824151 | Technical Reference - Page 11
    UB-E02 Technical Reference Guide How to Use this Guide Installation Overview Be sure to read Chapter 1, "System UB-E02. See Chapter 5. 4. To set the functions of the UB-E02 using the EPSON TMNet WebConfig utility, you need to use Microsoft Internet Explorer. If it is not installed, install it,
  • Epson C32C824151 | Technical Reference - Page 12
    Contents Chapter 1 System Preparation Supported Operating Systems 1-1 Supported Network Protocols 1-1 Supported TM Printers 1-1 Other using EPSON TMNet WinConfig 3-1 Setting the IP Address Using the arp/ping Command 3-11 EPSON TMNet WinConfig Functions 3-13 Menu Bar 3-14 EPSON TMNet
  • Epson C32C824151 | Technical Reference - Page 13
    UB-E02 Technical Reference Guide Chapter 5 Specifications Printer Connection 5-1 Line Display Connection 5-1 Features 5-1 Overview 5-1 Printing Functions 5-2 Functions to Monitor Settings 5-2 Maintenance Functions 5-2 Hardware Specifications 5-2 Physical communications standard 5-2 Board
  • Epson C32C824151 | Technical Reference - Page 14
    xii Contents Rev. A
  • Epson C32C824151 | Technical Reference - Page 15
    Chapter 1 System Preparation UB-E02 Technical Reference Guide 1.1 Supported Operating Systems ❏ Microsoft Windows 95, Windows 98 Second Edition, Windows 2000 Professional, and Windows XP Professional ❏ Windows NT 4.0 1.2 Supported Network Protocols ❏ LPR ❏ Socket printing (port 9100 for OPOS) 1.3
  • Epson C32C824151 | Technical Reference - Page 16
    The following printers cannot use the UB-E02. ❏ TM-J8000, TM-T285, RP-U420 1.4 Other Limitations Be sure to note the following: ❏ When the UB-E02 is installed, the display module connector (DM-D) of the TM printer cannot be used. CAUTION: Do not connect the Ethernet connector cable to the display
  • Epson C32C824151 | Technical Reference - Page 17
    they could short circuit connections and cause damage from excessive current. ❏ This product should only be connected to the devices specified in this guide. Connecting other devices could cause damage, fire or explosion. ❏ Do not attempt to wire this product other than as described in this document
  • Epson C32C824151 | Technical Reference - Page 18
    2.2 Unpacking ❏ UB-E02 ❏ UB-E02 User's Manual 2.3 Part Names Power supply connector of the printer 10BASE-T/100BASE-TX LED (green) LED (yellow) Ethernet interface connector Switch Drawer kick-out connector of the
  • Epson C32C824151 | Technical Reference - Page 19
    2.5 UB-E02 Installation UB-E02 Technical Reference Guide CAUTION: Before installing the UB-E02, be sure to set the DIP switches or Memory switches as shown in the table below. For other models,
  • Epson C32C824151 | Technical Reference - Page 20
    operating. During this time, all the communicating functions of the network do not work. The waiting time is: When the IP address setting is Manual (Fixed): approximately 6 seconds When the IP address setting is Auto: approximately 13 seconds (It can be longer, depending on the reply time of
  • Epson C32C824151 | Technical Reference - Page 21
    UB-E02 Technical Reference Guide 7. Print a status sheet to check whether the UB-E02 is installed correctly by holding the switch down for more than 3 seconds when the printer is
  • Epson C32C824151 | Technical Reference - Page 22
    2.6 Initializing UB-E02 All the parameters of internal settings for the UB-E02 can be set to the factory default values. Follow the steps below: 1. Turn off the printer power. Be sure to confirm that the LED lights are off. 2. Turn on the printer power while pressing the switch of the UB-E02 and
  • Epson C32C824151 | Technical Reference - Page 23
    UB-E02 Technical Reference Guide 2.8 FAQ 2.8.1 Q1. The printer does not operate correctly. ("Serial interface" is printed by time, the self test for the printer is not performed. Set the manual setting for IP address acquisition where the DHCP server is not available. Rev. A Installation 2-7
  • Epson C32C824151 | Technical Reference - Page 24
    2-8 Installation Rev. A
  • Epson C32C824151 | Technical Reference - Page 25
    Guide 3.1 Setting the IP Address To use the UB-E02 with TCP/IP, you first need to set its IP address. You can set the IP address by using the EPSON TMNet WinConfig or arp/ping command. setting UB-E02 Setting IP address EPSON APD manual. 3.1.1 Setting the IP Address using EPSON TMNet WinConfig Follow
  • Epson C32C824151 | Technical Reference - Page 26
    Windows 95 1. Double-click the Network icon in the Control Panel; then check whether TCP/IP is in the list of installed network components on the Configuration menu. If it is already installed, click Cancel and skip to the Installing TMNet WinConfig section. If TCP/IP is not in the list, click Add.
  • Epson C32C824151 | Technical Reference - Page 27
    UB-E02 Technical Reference Guide 3. Select Microsoft from the list of manufacturers and TCP/IP from the Network protocols list. Then click OK. 4. IP address. Note: After the TCP/IP is installed, restart your computer and move on to the Installing EPSON TMNet WinConfig section. Rev. A Utilities 3-3
  • Epson C32C824151 | Technical Reference - Page 28
    Windows NT 4.0 1. Double-click the Network icon in the Control Panel to check whether the TCP/IP Protocol is installed. If it is already installed, click Cancel and skip to the Installing TMNet WinConfig section. If the component is not installed, click Add. . 2. Select the TCP/IP protocol and
  • Epson C32C824151 | Technical Reference - Page 29
    UB-E02 Technical Reference Guide 3. If you continue installing the TCP/IP protocol, the TCP/ correctly. Note: After the TCP/IP is installed, restart your computer and move on to the Installing EPSON TMNet WinConfig section. Windows 2000 1. Double-click the Network and Dial Set Up icon in the Control
  • Epson C32C824151 | Technical Reference - Page 30
    EPSON TMNet WinConfig section. 3.1.1.2 Installing EPSON TMNet WinConfig Note: After the EPSON TMNet WinConfig is installed, if you add or remove protocols or services, the EPSON XP Professional, Windows NT 4.0. ❏ IBM PC/AT compatible with the operating systems mentioned above. 3-6 Utilities Rev. A
  • Epson C32C824151 | Technical Reference - Page 31
    UB-E02 Technical Reference Guide Installation with Windows 95 1. Unzip the file and start Setup.exe. 2. Install the EPSON TMNet WinConfig, following the instructions shown on your display. 3. When the installation is finished, click a check box, if necessary and then click Finish. Rev. A Utilities
  • Epson C32C824151 | Technical Reference - Page 32
    running, the UB-E02 is connected to the network, and the printer is turned on. 2. Click Start, point to Programs, point to EPSON TMNet WinConfig; then click EPSON TMNet WinConfig. 3. Click the printer where you want to set the IP address, and then click the Configuration button. (You might wait for
  • Epson C32C824151 | Technical Reference - Page 33
    UB-E02 Technical Reference Guide CAUTION: When you cannot check the MAC address on the E02 to check it. 4. Double-click the TCP/IP tab. 5. You can acquire the IP address by Auto or Manual setting. ❏ Auto setting: Acquire the IP address, subnet mask, and default gate way from DHCP server. A DHCP
  • Epson C32C824151 | Technical Reference - Page 34
    complete when the message "Configuration is successfully done" appears. Note: To get the information for the UB-E02 for the other segments, refer to the EPSON TMNet WinConfig Functions section. 3-10 Utilities Rev. A
  • Epson C32C824151 | Technical Reference - Page 35
    UB-E02 Technical Reference Guide 3.1.2 Setting the IP Address Using the arp/ping Command You can set the IP Address using the arp/ping command. This way of setting is
  • Epson C32C824151 | Technical Reference - Page 36
    .168.100.201. Now, setting the IP address is complete. Next, set the default gateway and Subnet mask for the UB-E02, referring to the EPSON TMNet WebConfig Functions. 3-12 Utilities Rev. A
  • Epson C32C824151 | Technical Reference - Page 37
    UB-E02 Technical Reference Guide 3.2 EPSON TMNet WinConfig Functions This section describes the functions, including options of the EPSON TMNet WinConfig. The main dialog box is shown below. . Item Tree view Item List view Launch Browser Configuration Explanation The tree structure indicates the
  • Epson C32C824151 | Technical Reference - Page 38
    3.2.1 Menu Bar The table shows each item and its function. Menu Device Indication Tool Help Sub Menus Setting Launch Browser Close Applications Update Time-out setting Find option Find the topics Version information Explanation Start the setting of the UB-E02 selected Start up the TMNet WebConfig
  • Epson C32C824151 | Technical Reference - Page 39
    Guide Search Options If you want to show and set a UB-E02 that is controlled by TCP/IP and is outside the local network, input the specific after executing Update in Indication menu or restarting the EPSON TMNet WinConfig. Item Enabling a specific address search IP address IP address list Add
  • Epson C32C824151 | Technical Reference - Page 40
    3.2.1.2 Settings Printer You can set the printer name. This also shows printer information. Item Printer name Model name Printer ID Printer type Version Explanation Set the printer name. Shows the printer model name. Shows the printer ID. Shows the printer type. Shows the ROM version. 3-16
  • Epson C32C824151 | Technical Reference - Page 41
    UB-E02 Technical Reference Guide Print server You can set administrator information. This also shows the printer server information Item Administrator name MAC address Hardware version Software version Explanation Shows
  • Epson C32C824151 | Technical Reference - Page 42
    TCP/IP You can set the TCP/IP. Item Get IP address Set by PING Subnet mask Default gateway IP address Explanation Auto or Manual is selectable for the UB-E02. Check the box if the setting of the UB-E02 by arg/ping is permitted. Set the subnet mask
  • Epson C32C824151 | Technical Reference - Page 43
    UB-E02 Technical Reference Guide Password The EPSON TMNet WinConfig can set a password to protect the UB-E02 lower-case characters are distinguished. CAUTION: The password is used for both the EPSON TMNet WinConfig and the EPSON TMNet Web Config. When you use either utility, be sure to control the
  • Epson C32C824151 | Technical Reference - Page 44
    TMNet WebConfig. Note: Launch a browser and input the IP address of the UB-E02. Be sure not to launch the EPSON TMNet WinConfig at the same time. Address: http://(IP address of the UB-E02)/ Note: Be sure to use Microsoft Internet Explorer 5.0 or later. 3.3.1 Opening
  • Epson C32C824151 | Technical Reference - Page 45
    UB-E02 Technical Reference Guide Item Information Configuration Network Configuration Option General TCP/IP SNMP TCP/IP Community IP Trap 1 IP Trap 2 Administrator Password Reset Advanced Explanation Show the UB-
  • Epson C32C824151 | Technical Reference - Page 46
    3.3.2 Protocol Information and Settings 3.3.2.1 General Information Item Interface card Printer Administrator name Location/Person Model name MAC address Software version Hardware version Printer ID Printer status Explanation Shows the administrator name. Shows the location or user name. Shows
  • Epson C32C824151 | Technical Reference - Page 47
    3.3.2.2 TCP/IP Information UB-E02 Technical Reference Guide Item Get IP Address Set using Automatic Private IP Addressing (APIPA) Set using PING IP Address Subnet Mask Default Gateway Explanation Shows the method of
  • Epson C32C824151 | Technical Reference - Page 48
    3.3.2.3 SNMP Information Item Community IP Trap Read Only Read/Write Trap 1 Address Community Name Trap 2 Address Community Name Explanation Shows he Read Community information. Shows the Read/Write Community information. Shows the Trap 1 information. Shows the Trap 1 Address. Shows the Trap 1
  • Epson C32C824151 | Technical Reference - Page 49
    3.3.2.4 TCP/IP Setting UB-E02 Technical Reference Guide Item Get IP Address Set using Automatic Private IP Addressing (APIPA) Set using PING IP Address Subnet Mask Default Gateway Explanation Select the method of
  • Epson C32C824151 | Technical Reference - Page 50
    3.3.2.5 SNMP Communication Setting Item Community Explanation Read Only Read/Write The setting is fixed to "Public." Set the Read/Write Community Name (up to 16 characters). 3-26 Utilities Rev. A
  • Epson C32C824151 | Technical Reference - Page 51
    3.3.2.6 SNMP IP Trap 1 Setting UB-E02 Technical Reference Guide Item Trap Address Community Name Explanation Set Trap 1. Set the Trap 1 Address. Set the Trap 1 Community Name. Rev. A Utilities 3-27
  • Epson C32C824151 | Technical Reference - Page 52
    3.3.2.7 SNMP IP Trap 2 Setting Item Trap Address Community Name Explanation Set Trap 2. Set the Trap 2 Address. Set the Trap 2 Community Name. 3-28 Utilities Rev. A
  • Epson C32C824151 | Technical Reference - Page 53
    3.3.2.8 Administrator Setting UB-E02 Technical Reference Guide Item Explanation Administrator Name Set the administrator name. Location/Person Set the location or user name. Rev. A Utilities 3-29
  • Epson C32C824151 | Technical Reference - Page 54
    3.3.2.9 Password Setting Item Old Password New Password Re-input Password Explanation Input the old password. Input the new password. Re-input the new password. 3-30 Utilities Rev. A
  • Epson C32C824151 | Technical Reference - Page 55
    3.3.2.10 Reset UB-E02 Technical Reference Guide Item Reset Factory Default Explanation Resets the UB-E02 to its status when the power was turned on. Returns to the factory default settings. Rev. A Utilities 3-31
  • Epson C32C824151 | Technical Reference - Page 56
    3.3.2.11 Advanced Item Physical Layer Setting Explanation Set the communication method. 3-32 Utilities Rev. A
  • Epson C32C824151 | Technical Reference - Page 57
    Chapter 4 Programming Samples UB-E02 Technical Reference Guide This chapter describes the following: ❏ Method of printing to the UB-E02 ❏ Direct printing by PORT9100 ❏ Commands sent to a TM printer when the power is
  • Epson C32C824151 | Technical Reference - Page 58
    , the command statuses sent by the printer are ignored because the printing by lpr applies only to the output of the printer. The UB-E02 supports direct printing by TCP PORT9100. It is possible to control the printer directly by an application with the ESC/POS commands through writing and reading
  • Epson C32C824151 | Technical Reference - Page 59
    UB-E02 Technical Reference Guide 4.2 Direct Printing by PORT9100 4.2.1 For Windows Console The program is a sample of printing "EPSON UB-E02" to a TM printer with the UB-E02 from the Windows shell, through the ethernet connection. /* TCP9100 programming sample for win32 * HOW TO BUILD *
  • Epson C32C824151 | Technical Reference - Page 60
    /* send data */ send(sock, "EPSON\n", 6, 0); /* gracefully close */ shutdown(sock, 1);/* SD_SEND */ while (1) { char buf[64]; int n = recv(sock, buf, 64, 0); if (n = SOCKET_ERROR || n == 0) break; } shutdown(sock, 2);/* SD_BOTH */ /* close socket */ closesocket(sock); return 0; } 4-4
  • Epson C32C824151 | Technical Reference - Page 61
    UB-E02 Technical Reference Guide 4.2.2 For Linux The program is a sample of printing "EPSON UB-E02" to a TM printer with the UB-E02 < 0) { perror("connect()"); } printf("connected\n"); /* send data */ send(sock, "EPSON\n", 6, 0); /* close socket */ close(sock); return 0; } Rev. A 4-5 Programming
  • Epson C32C824151 | Technical Reference - Page 62
    4.3 Commands Sent to a TM Printer When the Power is On When the power is turned on, the UB-E02 transmits the following commands to the TM printer and maintains the statuses. The UB-E02 acquires printer information by GS I and monitors the printer status through the TMNet WebConfig using the GS a 255
  • Epson C32C824151 | Technical Reference - Page 63
    Technical Reference Guide 4.7 Printer Operation 0 × 00, 0 × 00 fixed Length (n) Command parameter Packet Reply Character string "EPSON" Packet type reply: 'q': Query reply 'c': Command reply Device type (0 × 03 fixed) FFFFh: Function requested are not supported Rev. A 4-7 Programming Samples
  • Epson C32C824151 | Technical Reference - Page 64
    4.7.2 03-0000 Retrieving Basic Information 4.7.2.1 Reply data Off-set Size 14 1 15 1 16 1 17 1 18 1 19 n Description Interface type Communication method with TM printer Printer ID acquired during a power-on Printer type ID acquired during a power-on Printer ROM version acquired during
  • Epson C32C824151 | Technical Reference - Page 65
    UB-E02 Technical Reference Guide 4.7.4 03-0011 Forced Transmission Transmission is done, regardless of the flow control between the TM printer and the UB-E02. 4.7.4.1 Set-up data Off-set
  • Epson C32C824151 | Technical Reference - Page 66
    4.7.6 03-0013 Buffer Flash 4.7.6.1 Reply data Off-set Size 14 1 Description Result 0: Normal Except for 0: Failure ❏ This clears only the buffer of the UB-E02 and cannot clear the receive buffer of the printer. 4.7.7 03-0016 Clearing Connection Time-Out Timer Regularly send commands clearing
  • Epson C32C824151 | Technical Reference - Page 67
    UB-E02 Technical Reference Guide 4.7.8 Programming Sample 4.7.8.1 For Windows Console /* UDP3289 programming sample for win32 * HOW TO BUILD * cc wudp.cpp wsock32.lib */ #include #include #define MAXBUF 512
  • Epson C32C824151 | Technical Reference - Page 68
    buf[11] = 0x00; buf[12] = 0x00; // Parameter length buf[13] = 0x00; /* send a packet */ i = sendto(sock, buf, 14, 0, (struct sockaddr*)&addr, sizeof(addr)); /* receive packet */ fromlen = sizeof(addr); len = recvfrom(sock, buf, MAXBUF, 0, (struct sockaddr*)&addr, &fromlen); /* print receive packet
  • Epson C32C824151 | Technical Reference - Page 69
    [7] = 0x00; // DeviceNumber(0) buf[8] = 0x00; // Function(0010h) buf[9] = 0x10; buf[10] = 0x00; // Result buf[11] = 0x00; buf[12] = 0x00; // parameter length Length UB-E02 Technical Reference Guide Rev. A 4-13 Programming Samples
  • Epson C32C824151 | Technical Reference - Page 70
    buf[13] = 0x00; /* send packet */ i = sendto(sock, buf, 14, 0, (struct sockaddr*)&addr, sizeof(addr)); /* receive packet */ fromlen = sizeof(addr); len = recvfrom(sock, buf, MAXBUF, 0, (struct sockaddr*)&addr, &fromlen); /* print receive packet */ if (len) { if ((buf[10] == 0x00) && (buf[11] == 0x00
  • Epson C32C824151 | Technical Reference - Page 71
    Chapter 5 Specifications UB-E02 Technical Reference Guide The UB-E02 can be installed in the TM-series printers as an interface board to provide 10 Base-T/100 Base-TX communications. Host PC EPSON PRINTER WITH UB-E02 Ethernet (10Base-T/100Base-TX) EPSON PRINTER 5.1 Printer Connection The
  • Epson C32C824151 | Technical Reference - Page 72
    DHCP ❏ Supports APIPA ❏ ping response ❏ Status printing function ❏ Module setting initialization using the Test switch ❏ Status monitoring by ENPC ❏ Status monitoring by SNMP 5.3.4 Maintenance Functions ❏ Firmware writing through the network 5.4 Hardware Specifications 5.4.1 Physical communications
  • Epson C32C824151 | Technical Reference - Page 73
    Guide 5.4.3 External appearance and connector locations 10BASE-T Ethernet interface connector LED (green) LED (red) Switch 5.5 Software Specifications Time out: 5 minutes ❏ Job deletion: not supported ❏ Banner printing: not supported 5.5.2.2 Socket Communications ❏ Port type: TCP comm.
  • Epson C32C824151 | Technical Reference - Page 74
    settings or printer status by custom setup utility. 5.5.3.1 HTTP ❏ Port number: 80 ❏ User name: EPSON ❏ Password: None ❏ Maximum simultaneous -write Read-write Default "Public" None None None ❏ Trap destination ❏ MIB support Up to two settable IP addresses Part of MIB-II (RFC1213) Part of
  • Epson C32C824151 | Technical Reference - Page 75
    Guide ❏ PDU support Get Request Get Next Request Set Request Get Response Trap ❏ Server port number 161 ❏ Trap sending port number 162 5.5.3.3 ENPC ❏ Protocol: UDP/IP ❏ UDP port number: 3289 ❏ Compatible packet types: Probe Initialize Query Setup APIPA manual setting Specifications 5-5
  • Epson C32C824151 | Technical Reference - Page 76
    is not used in the same network is assigned. However, communication over the router is not possible when the IP address is set by APIPA. 5.5.4.3 Manual Setting The UB-E02 operates in accordance with the IP address stored in the internal parameter settings
  • Epson C32C824151 | Technical Reference - Page 77
    UB-E02 Technical Reference Guide 5.5.5 Internal Settings 5.5.5.1 Item Disable None oo o o × oo o o × oo o o × None oo o o × None oo o o × None oo o o × None ×o × o × Auto negotiation o o o o o o× o × o o× o × o o× o × o Rev. A Specifications 5-7
  • Epson C32C824151 | Technical Reference - Page 78
    which can set miscellaneous with the ENPC protocol is provided by EPSON. 5.5.5.4 Setting with Browser Setting can be made by an HTTP from a host in the same segment as the module. The host must support both arp and ping commands. The new IP address takes effect when the .) 5-8 Specifications Rev. A
  • Epson C32C824151 | Technical Reference - Page 79
    , depending on the reply time of the host.) 5.5.7 Version Upgrading The module can upgrade its own firmware over the network. 5.5.7.1 Supported protocol ❏ TFTP 5.5.7.2 Upgrade Methods ❏ By TFTP command (for Windows XP/2000/NT4.0) For more information, ask your dealer. Rev. A Specifications 5-9
  • Epson C32C824151 | Technical Reference - Page 80
    5.6 Environmental Specifications Temperature:0 to 50° C {32 to 122° F} Humidity:10 to 90% RH (non-condensing) 5.7 Storage Conditions Temperature: -10 to 50° C {14 : (EMI) FCC/ICES-003 Class A Japan: (EMC) VCCI Class A Oceania: (EMC) AS/NZS 3548, CISPR22 Class B 5-10 Specifications Rev. A
  • Epson C32C824151 | Technical Reference - Page 81
    Appendix A Definitions UB-E02 Technical Reference Guide A ASB- Auto Status Back: The feature that allows the printer to send the status information back to the host computer automatically. ARP -Address Resolution Protocol:
  • Epson C32C824151 | Technical Reference - Page 82
    TCP/IP-Name given to the suite of protocols (including but not limited to TCP and IP) that govern the transmission and services of a network. The TCP indicates a transport layer and the IP indicates an internet layer. TCP port-A logical connection point in the software on a TCP/IP
  • Epson C32C824151 | Technical Reference - Page 83
  • Epson C32C824151 | Technical Reference - Page 84
    EPSON SEIKO EPSON CORPORATION Printed in Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
UB-E02
Technical Reference
Guide
10Base-T/100Base-TX
Ethernet Interface board
EPSON
English
404999000