Dell Brocade 6510 Fabric OS Message Reference v7.1.0

Dell Brocade 6510 Manual

Get Dell Brocade 6510 PDF manuals and user guides View all Dell Brocade 6510 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell Brocade 6510 manual content summary:

  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 1
    53-1002749-01 ® 14 December 2012 Fabric OS Message Reference Supporting Fabric OS v7.1.0
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 2
    , equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without technical data contained in this document may require an export license from the United States government. The authors and Brocade Communications
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 3
    Reference Manual PLAT-1001 July 2005 Fabric OS System Error Message 53-1000046-01 Added BM, FCR, IPS, FCIP, SEC, and Reference Manual ZONE messages January 2006 Fabric rebranding, supported hardware, CLI changes. June 2007 Fabric OS Message Reference 53-1000600-01 Updated for Fabric OS v6
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 4
    chapters. November 2008 53-1001338-01 Updated for Fabric OS v6.3.0: -Modified a message to BKSW, BL, BKSW, BLL, CDR, CEE CONFIG, CONF, EM, FCOE, FCPD, FCPH, FCR, FICON, FICU, FLOD, FSPF, FSSM, FW, HAM,,HAMK, HIL, IPS, ISNS, L2SYS, MFIC, PDM, PLAT, PORT, RCS, RPCD, RTWR, SEC, SNMP, SWCH, TRCE
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 5
    Fabric OS Message Reference Publication Summary of changes Date number 53-1002149-01 Updated for Fabric OS v7.0.0: -Added new chapters: C3, CAL, MCAST_SS, RTE, and VS. -Added new messages: AG, AN, ANV, BL, C2, CDR, CCFG, ECC, EM, ESS, FABR, FCOE, FCPH, FICN, FICU, FSPF, FW, HIL, IPAD, IPS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 6
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 7
    xiii Supported hardware and software xiii What's new in this document xv Document conventions xvii Text formatting xvii Command syntax conventions xvii Command examples xviii Notes, cautions, and warnings xviii Key terms xix Notice to the reader xix Additional information xix Brocade
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 8
    message 26 Looking up a system message 26 Gathering information about the problem 26 Support 27 System module descriptions 28 Log Messages Audit Messages FFDC Messages Fabric OS System Messages AG Messages 121 AN Messages 136 ANV Messages 140 viii Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 9
    Fabric OS Message Reference 53-1002749-01 AUTH Messages 144 BKSW Messages 162 BL Messages 300 EVMD Messages 303 FABR Messages 304 FABS Messages 321 FBC Messages 326 FCMC Messages 327 FCOE Messages 328 FCPD Messages 341 FCPH Messages 343 FCR Messages 345 FICN Messages 374 FICU Messages
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 10
    565 HMON Messages 567 HSL Messages 568 HTTP Messages 571 IBD Messages 572 IPAD Messages 573 IPS Messages 575 ISNS Messages 578 KAC Messages 582 KSWD Messages 587 KTRC Messages 588 L2SS PDTR Messages 650 PLAT Messages 651 PMGR Messages 653 x Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 11
    PORT Messages 657 PS Messages 660 PSWP Messages 664 RAS Messages 667 RCS Messages 672 RKD Messages 677 RMON Messages 679 Messages 871 VDR Messages 872 VS Messages 873 WEBD Messages 876 XTUN Messages 879 ZEUS Messages 889 ZONE Messages 892 Fabric OS Message Reference xi 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 12
    xii Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 13
    parts of procedures documented here apply to some switches but not to others, this guide identifies exactly which switches are supported and which are not. Although many different software and hardware configurations are tested and supported by Brocade Communications Systems, Inc. for Fabric OS v7
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 14
    hardware platforms are supported by this release of Fabric OS: • Brocade 300 • Brocade 5100 • Brocade 5300 • Brocade 5410 • Brocade 5424 • Brocade 5430 • Brocade 5450 • Brocade 5460 • Brocade 5470 • Brocade 5480 • Brocade 6505 • Brocade 6510 • Brocade 6520 • Brocade 7800 • Brocade 8000 • Brocade
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 15
    The following changes have been made since this document was last released: • The lookup lists in Chapter 2 through Chapter 4 provide hyperlinks to messages by type (LOG - TRCE Messages - VDR Messages - XTUN Messages - ZEUS Messages - ZONE Messages Fabric OS Message Reference xv 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 16
    - FSPF Messages - FSS Messages - HIL Messages - HSL Messages - HTTP Messages - IPS Messages - KAC Messages - KTRC Messages - L2SS Messages - LFM Messages - PMGR Messages - PS Messages - RCS Messages - RTWR Messages - SEC Messages - ZONE Messages xvi Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 17
    names in the narrative portions of this guide are presented in mixed lettercase: for example, switchShow. In actual examples, command lettercase is all lowercase. Command syntax conventions Command syntax in this manual follows these conventions: Fabric OS Message Reference xvii 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 18
    how to perform configuration tasks using the Fabric OS command line interface, but does not describe the commands in detail. For complete descriptions of all Fabric OS commands, including syntax, operand description, and sample output, see the Fabric OS Command Reference. Notes, cautions, and
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 19
    at no cost for a user ID and password. White papers, online demonstrations, and data sheets are available through the Brocade website at: http://www.brocade.com/products-solutions/products/index.page For additional Brocade documentation, visit the Brocade website: http://www.brocade.com Release
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 20
    switch support supplier for hardware, firmware, and software support management comb. • Brocade DCX-4S and DCX 8510-4-On the non-port side of the chassis, on the lower left side. 3. World Wide Name (WWN) Use the licenseIdShow command to display the WWN of the chassis. xx Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 21
    command because the switch is inoperable, you can get the WWN from the same place as the serial number, except for the Brocade DCX. For the Brocade DCX, access the numbers on the WWN cards by removing the Brocade logo plate at the top of the non-port side of the chassis. Document feedback
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 22
    xxii Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 23
    •Commands for displaying and configuring the system message logs . . . . . 13 •Displaying message content on switch 14 •Configuring system messages This guide supports Fabric OS v7.1.0 and documents system messages that can help you diagnose and fix problems with a switch or fabric. The messages
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 24
    is designed to support post-event audits and problem determination based on high-frequency events of certain types such as security violations, zoning configuration changes, firmware downloads, and certain types of fabric events. Audit messages flagged as AUDIT are not saved in the switch error logs
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 25
    changes. You can audit Virtual Fabric (Logical Switch)-related changes. You can audit the CLI commands executed on the switch. Used to audit or track the RASLog messages or modules that are enabled or disabled using the rasAdmin command. NOTE: The RAS class is not configurable, and it is always
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 26
    snmpConfig command to configure the SNMPv1 and SNMPv3 hosts and their configurations. • Audit messages are streamed to the switch console, and are forwarded to the configured syslog servers. The Audit log messages are not forwarded to an SNMP management station. 4 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 27
    of one or more servers, perform the following steps. 1. Log in to the switch as admin. 2. Execute the syslogdIpAdd IP address command to add a server to which system messages are forwarded. switch:admin> syslogdipadd 192.0.2.2 You can configure up to six syslog servers to receive the syslog messages
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 28
    > errfilterset -d console -v error 3. Execute the errFilterSet command to verify the configured filter settings. switch:admin> errfilterset console: filter severity = ERROR SNMP trap recipient An unsolicited message that comes to the management station from the SNMP agent on the device is called
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 29
    . Brocade switches send traps out on UDP port 162. To receive traps, the management station IP address must be configured on the switch. You can configure the SNMPv1 and SNMPv3 hosts to receive the traps. For more information on the swEventTrap, refer to the Fabric OS MIB Reference. Configuring the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 30
    recipient Port : (0..65535) [162] Trap Recipient's IP address : [192.0.20.20] [...] NOTE To receive the SNMP traps, the username, the authentication protocol, the UDP port number, and the privacy protocol must match between the switch and the management station. 8 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 31
    the SNMP traps. Brocade devices support SNMPv3 informs. Configuring the SNMPv3 inform recipient To configure the SNMPv3 host to receive the SNMP informs, perform the following steps. 1. Log in to the switch as admin. 2. Execute the snmpConfig --set snmpv3 command to configure the inform recipient
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 32
    the switch and the management station. 3. Execute the snmpConfig --show snmpv3 command to verify the SNMP agent configuration. switch:admin> snmpconfig --show snmpv3 SNMP Informs = 1 (ON) SNMPv3 USM configuration: User 1 (rw): snmpadmin1 Auth Protocol: noAuth 10 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 33
    trap, swEventTrap, is sent to the configured trap recipients. By default, the severity level is set at 0 (None), implying that all the event traps are sent. Use the snmpConfig --set mibCapability command to modify the severity level of swEventTrap. Fabric OS Message Reference 11 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 34
    snmpConfig --set mibCapability command to configure MIBs interactively. All the supported MIBs and associated traps are displayed. You can change the DesiredSeverity for swEventTrap to 1 (Critical), 2 (Error), 3 (Warning), or 4 (Informational). The default value is 0. switch:admin> snmpconfig --set
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 35
    that you can use to view or configure the system message logs. Most commands require the admin access level. For detailed information on required access levels and commands, refer to the Fabric OS Command Reference. TABLE 3 Commands for viewing or configuring the system parameters and message logs
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 36
    to change the default severity level for a specified message, and to display configured RASLog message settings. Displays message documentation on switch. Sets the verbose level of a particular module within the Fabric OS. snmpConfig Manages the SNMP agent configuration. supportFfdc Enables and
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 37
    CAUSE Indicates that FC Routing (FCR) is enabled on the specified fabric. RECOMMENDED ACTION Top Talker cannot be installed on a fabric with FCR service enabled. In case Top Talker must be installed on a fabric, disable FCR using the fosconfig --disable fcr command. Configuring system messages and
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 38
    auditCfg --show command to verify the configuration. switch:admin> auditcfg --show Audit filter is enabled. 1-ZONE 2-SECURITY 3-CONFIGURATION 4-FIRMWARE 5-FABRIC 6-FW 7-LS 8-CLI Severity level: ERROR You must configure the syslog daemon to send the Audit events to a configured remote host using the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 39
    . switch:admin> rasadmin --show -severity C2-1004 Message Severity C2-1004 : WARNING Displaying system message logs and attributes This section provides information on displaying the system message logs. These procedures are valid for all the supported platforms. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 40
    command line. switch:admin> errdump Version: v7.1.0 2000/12/17-05:54:30, [HAM-1004], 1, CHASSIS, INFO, switch, Processor rebooted - Reset 2000/12/17-05:55:04, [ZONE-1034], 2, FID 128, INFO, switch, A new zone database file is created. 2000/12/17-05:55:04, [FCR-1069], 3, FID 128, INFO, switch, The FC
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 41
    errDump --attribute FFDC command at the command line. switch:admin> errDump --attribute FFDC Fabric OS: v7.1.0 2012/10/15-10:39:02, [LOG-1002], 4496, FFDC, WARNING, switch, A log message was not recorded. 2012/10/15-10:39:18, [RAS-1001], 4496, FFDC, WARNING, switch, First failure data capture (FFDC
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 42
    to a module: • Execute the rasadmin --show -all command to the status of all RASLog messages in the system log. switch:admin> rasadmin --show -all Message Status Default Severity FCIP-1000 ENABLED CRITICAL FCIP-1001 ENABLED INFO FCIP-1002 ENABLED INFO [...] Current Severity CRITICAL ERROR
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 43
    based on the severity level, perform the following steps. 1. Log in to the switch as admin. 2. Execute the errdump --severity [DEFAULT | INFO | WARNING | ERROR | CRITICAL] command. For more information on message severity levels, refer to "Message severity levels" on page 3. You can set the count of
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 44
    system message logs. These procedures are valid for all the supported platforms. Clearing the system message log To clear the system message log for a particular switch instance, perform the following steps. 1. Log in to the switch as admin. 2. Execute the errClear command to clear all messages from
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 45
    , SLOT 6 | FFDC | FID 128, INFO, ESNSVT_DCX, Login information: Login successful via TELNET/SSH/RSH. IP Addr:192.0.2.2. NOTE Any reference to slot 0 in a system message is a reference to the blade within the switch platform, for example, Brocade DCX contains FC8-48 blade, FC8-32 blade, FC8-16 blade
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 46
    reset to 1 using the errClear command. The sequence number is persistent across power cycles and switch reboots. Flags Severity Level Switch SECURITY, JohnSmith/root/192.0.2.2/Telnet/CLI, Domain A/JohnsSwitch, , Incorrect password during login attempt. 24 Fabric OS Message Reference 53-1002749-
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 47
    generated on the switch. The RASLog subsystem will support an internationalized time stamp format based on the "LOCAL" setting. The message module and number. These values uniquely identify each message in the Fabric OS and reference the cause and actions recommended in this manual. Note that not
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 48
    Probable cause • Recommended action Gathering information about the problem Questions to ask yourself when troubleshooting a system message are as follows: • What is the current Fabric OS level? • What is the switch hardware version? • Is the switch operational? • Assess impact and urgency: - Is the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 49
    Execute the errDump command on each logical switch. • Execute the supportFtp command (as needed) to set up automatic FTP transfers, and then execute the supportSave command. Support Fabric OS creates a number of files that can help support personnel troubleshoot and diagnose a problem. This section
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 50
    Fibre Channel over IP port configuration messages over the Brocade 7800 and FX8-24 blade. Blade management error messages are a result of autoleveling firmware upgrades performed by the control processor (CP). C2 error messages indicate problems with the 8 Gbps-capable FC module of the Fabric OS. C3
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 51
    switches, creating a spanning tree, throttling the trunking process, and distributing the domain and alias lists to all switches in the fabric. Fabric OS system driver module. Firmware blade compatibility errors with the control processor (CP). Fibre Channel miscellaneous messages relate to problems
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 52
    . HSL error messages indicate problems with the Hardware Subsystem Layer of the Fabric OS. HTTP error messages. IBD generates messages related to port restart failure. System messages generated by the IP admin demon. Fibre Channel over IP license, tunneling, and port-related messages. ISNS server
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 53
    ) • Fabric Device Management Interface daemon (fdmid) • Fabric Watch daemon (fwd) • FCoE daemon (fcoed) • Fibre Channel Protocol daemon (fcpd) • FICON CUP daemon (ficud) • FSPF daemon (fspfd) • IGMP daemon (igmpd) • IMI daemon (imid) • Inter-fabric Routing daemon (iswitchd) • IP Storage
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 54
    CP blade to the standby CP blade. PDTR PDTR messages indicate panic dump trace files have been created. PLAT PLAT messages indicate hardware problems. PMGR A group of messages relating to logical switch creation, deletion, and configuration. 32 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 55
    as an SNMP agent). It also allows the switch to send traps to the defined and configured management station. Brocade switches support six management entities that can be configured to receive these traps. SPC messages indicate problems and informational updates associated with the security processor
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 56
    any problems during the firmwareDownload procedure. Most messages are informational only and are generated even during successful firmware download. For additional information, refer to the Fabric OS Administrator's Guide. These messages are generated by the switch driver module that manages a Fibre
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 57
    -1016 AG-1017 AG-1018 AG-1019 AG-1020 AG-1021 AG-1022 AG-1023 AG-1024 AG-1025 AG-1026 AG-1027 AG-1028 Fabric OS Message Reference 53-1002749-01 Chapter 2 35
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 58
    AN-1004 AN-1005 AN-1010 AN-1011 AN-1012 AN-1013 ANV Messages ANV-1001 ANV-1002 ANV-1003 ANV-1004 ANV-1005 36 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 59
    -1017 AUTH-1018 AUTH-1020 AUTH-1022 AUTH-1023 AUTH-1025 AUTH-1026 AUTH-1027 AUTH-1028 AUTH-1029 AUTH-1030 AUTH-1031 AUTH-1032 Fabric OS Message Reference 53-1002749-01 AUTH Messages 2 37
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 60
    BL-1002 BL-1003 BL-1004 BL-1006 BL-1007 BL-1008 BL-1009 BL-1010 BL-1011 BL-1012 BL-1013 BL-1014 38 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 61
    -1036 BL-1037 BL-1038 BL-1039 BL-1041 BL-1045 BL-1046 BL-1047 BL-1048 BL-1049 BL-1050 BL-1051 BL-1052 Fabric OS Message Reference 53-1002749-01 BL Messages 2 39
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 62
    BM-1055 BM-1056 BM-1058 C2 Messages C2-1001 C2-1002 C2-1004 C2-1006 C2-1007 C2-1008 C2-1009 C2-1010 40 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 63
    -1011 C3-1012 C3-1013 C3-1014 C3-1015 C3-1016 C3-1017 C3-1018 C3-1019 C3-1020 C3-1021 C3-1023 C3-1025 Fabric OS Message Reference 53-1002749-01 C3 Messages 2 41
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 64
    CDR-1001 CDR-1002 CDR-1003 CDR-1004 CDR-1005 CDR-1006 CDR-1007 CDR-1008 CDR-1009 CDR-1010 CDR-1011 CDR-1012 42 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 65
    -1006 CNM-1007 CNM-1008 CNM-1009 CNM-1010 CNM-1011 CNM-1012 CNM-1013 CNM-1014 CNM-1015 CNM-1016 CNM-1017 CNM-1018 Fabric OS Message Reference 53-1002749-01 CHS Messages 2 43
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 66
    CNM-1042 CNM-1043 CNM-1044 CNM-1045 CNM-1046 CNM-1047 CNM-1048 CNM-1049 CNM-1050 CNM-1051 CNM-1052 CNM-1053 44 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 67
    Messages CONF-1000 CONF-1001 CONF-1021 CONF-1023 CONF-1024 CONF-1030 CONF-1031 CONF-1032 CONF-1040 CONF-1041 CONF-1042 CONF-1043 Fabric OS Message Reference 53-1002749-01 CONF Messages 2 45
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 68
    CVLC-1017 CVLC-1018 CVLC-1019 CVLC-1020 CVLC-1021 CVLC-1022 CVLC-1023 CVLC-1024 CVLC-1025 CVLC-1026 CVLC-1027 CVLC-1028 46 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 69
    -1012 CVLM-1013 CVLM-1014 CVLM-1015 CVLM-1016 CVLM-3001 CVLM-3002 CVLM-3003 CVLM-3004 CVLM-3005 CVLM-3006 CVLM-3007 CVLM-3008 Fabric OS Message Reference 53-1002749-01 CVLM Messages 2 47
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 70
    -3027 CVLM-3028 DOT1 Messages DOT1-1001 DOT1-1002 DOT1-1003 DOT1-1004 DOT1-1005 DOT1-1006 DOT1-1007 DOT1-1008 DOT1-1009 DOT1-1010 48 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 71
    -1018 EM-1019 EM-1020 EM-1028 EM-1029 EM-1031 EM-1033 EM-1034 EM-1035 EM-1036 EM-1037 EM-1042 EM-1043 Fabric OS Message Reference 53-1002749-01 ECC Messages 2 49
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 72
    EM-1071 EM-1072 EM-2003 ESS Messages ESS-1001 ESS-1002 ESS-1003 ESS-1004 ESS-1005 ESS-1008 ESS-1009 ESS-1010 50 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 73
    -1008 FABR-1009 FABR-1010 FABR-1011 FABR-1012 FABR-1013 FABR-1014 FABR-1015 FABR-1016 FABR-1017 FABR-1018 FABR-1019 FABR-1020 Fabric OS Message Reference 53-1002749-01 ESW Messages 2 51
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 74
    FABR-1049 FABR-1050 FABR-1051 FABR-1052 FABR-1053 FABR-1054 FABR-1055 FABS Messages FABS-1001 FABS-1002 FABS-1004 FABS-1005 52 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 75
    -1015 FBC Messages FBC-1001 FCMC Messages FCMC-1001 FCOE Messages FCOE-1001 FCOE-1002 FCOE-1003 FCOE-1004 FCOE-1005 FCOE-1006 FCOE-1007 FCOE-1009 FCOE-1010 FCOE-1012 FCOE-1014 FCOE-1015 FCOE-1016 FCOE-1017 FCOE-1019 FCOE-1021 FCOE-1022 Fabric OS Message Reference 53-1002749-01 FBC Messages 2 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 76
    FCOE-1029 FCOE-1030 FCOE-1031 FCOE-1032 FCOE-1033 FCOE-1034 FCOE-1037 FCOE-1038 FCOE-1039 FCOE-1040 FCOE-1041 FCOE-1042 FCOE-1043 FCOE-1044 FCOE-1045 FCOE-1046 FCOE-1047 FCOE-1048 FCPD Messages FCPD-1001 FCPD-1002 FCPD-1003 FCPH Messages FCPH-1001 FCPH-1002 FCPH-1003 54 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 77
    -1021 FCR-1022 FCR-1023 FCR-1024 FCR-1025 FCR-1026 FCR-1027 FCR-1028 FCR-1029 FCR-1030 FCR-1031 FCR-1032 FCR-1033 Fabric OS Message Reference 53-1002749-01 FCR Messages 2 55
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 78
    FCR-1064 FCR-1065 FCR-1066 FCR-1067 FCR-1068 FCR-1069 FCR-1070 FCR-1071 FCR-1072 FCR-1073 FCR-1074 FCR-1075 56 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 79
    -1098 FICN Messages FICN-1003 FICN-1004 FICN-1005 FICN-1006 FICN-1007 FICN-1008 FICN-1009 FICN-1010 FICN-1011 FICN-1012 FICN-1013 Fabric OS Message Reference 53-1002749-01 FICN Messages 2 57
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 80
    FICN-1037 FICN-1038 FICN-1039 FICN-1040 FICN-1041 FICN-1042 FICN-1043 FICN-1044 FICN-1045 FICN-1046 FICN-1047 FICN-1048 58 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 81
    -1071 FICN-1072 FICN-1073 FICN-1074 FICN-1075 FICN-1076 FICN-1077 FICN-1078 FICN-1079 FICN-1080 FICN-1081 FICN-1082 FICN-1083 Fabric OS Message Reference 53-1002749-01 FICN Messages 2 59
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 82
    FICN-1107 FICN-1108 FICN-1109 FICN-1110 FICN-1111 FICN-1112 FICN-1113 FICN-1114 FICN-1115 FICN-1116 FICN-1117 FICN-1118 60 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 83
    -1007 FICU-1008 FICU-1009 FICU-1010 FICU-1011 FICU-1012 FICU-1013 FICU-1017 FICU-1018 FICU-1019 FICU-1020 FICU-1021 FICU-1022 Fabric OS Message Reference 53-1002749-01 FICU Messages 2 61
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 84
    FSPF-1009 FSPF-1010 FSPF-1011 FSPF-1012 FSS Messages FSS-1001 FSS-1002 FSS-1003 FSS-1004 FSS-1005 FSS-1006 FSS-1007 62 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 85
    -1011 FW-1012 FW-1033 FW-1034 FW-1035 FW-1036 FW-1037 FW-1038 FW-1039 FW-1040 FW-1041 FW-1042 FW-1043 Fabric OS Message Reference 53-1002749-01 FSSM Messages 2 63
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 86
    FW-1125 FW-1126 FW-1127 FW-1128 FW-1129 FW-1130 FW-1131 FW-1132 FW-1133 FW-1134 FW-1135 FW-1136 64 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 87
    -1178 FW-1179 FW-1180 FW-1181 FW-1182 FW-1183 FW-1184 FW-1185 FW-1186 FW-1187 FW-1188 FW-1189 FW-1190 Fabric OS Message Reference 53-1002749-01 FW Messages 2 65
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 88
    FW-1242 FW-1243 FW-1244 FW-1245 FW-1246 FW-1247 FW-1248 FW-1249 FW-1250 FW-1251 FW-1272 FW-1273 66 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 89
    -1316 FW-1317 FW-1318 FW-1319 FW-1320 FW-1321 FW-1322 FW-1323 FW-1324 FW-1325 FW-1326 FW-1327 FW-1328 Fabric OS Message Reference 53-1002749-01 FW Messages 2 67
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 90
    FW-1352 FW-1353 FW-1354 FW-1355 FW-1356 FW-1357 FW-1358 FW-1359 FW-1360 FW-1361 FW-1362 FW-1363 68 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 91
    -1406 FW-1407 FW-1408 FW-1424 FW-1425 FW-1426 FW-1427 FW-1428 FW-1429 FW-1430 FW-1431 FW-1432 FW-1433 Fabric OS Message Reference 53-1002749-01 FW Messages 2 69
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 92
    FW-1515 FW-1516 FW-1517 FW-1518 FW-1519 FW-1520 FW-1521 FW-1522 FW-1523 FW-1524 FW-1525 FW-1526 70 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 93
    -3021 FW-3022 HAM Messages HAM-1001 HAM-1002 HAM-1004 HAM-1005 HAM-1006 HAM-1007 HAM-1008 HAM-1009 HAM-1010 HAM-1011 Fabric OS Message Reference 53-1002749-01 HAM Messages 2 71
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 94
    HIL-1206 HIL-1207 HIL-1208 HIL-1301 HIL-1302 HIL-1303 HIL-1304 HIL-1305 HIL-1306 HIL-1307 HIL-1308 HIL-1309 72 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 95
    -1603 HIL-1605 HIL-1610 HIL-1611 HIL-1612 HIL-1613 HIL-1650 HLO Messages HLO-1001 HLO-1002 HLO-1003 HMON Messages HMON-1001 Fabric OS Message Reference 53-1002749-01 HLO Messages 2 73
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 96
    -1007 HTTP Messages HTTP-1001 HTTP-1002 HTTP-1003 IBD Messages IBD-1000 IPAD Messages IPAD-1000 IPAD-1001 IPAD-1002 IPAD-1003 IPAD-1004 IPS Messages IPS-1001 IPS-1002 IPS-1003 IPS-1004 IPS-1005 IPS-1006 IPS-1007 74 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 97
    -1008 KAC-1009 KAC-1010 KAC-1011 KAC-1012 KAC-1013 KAC-1014 KAC-1015 KAC-1016 KAC-1017 KSWD Messages KSWD-1001 KSWD-1002 Fabric OS Message Reference 53-1002749-01 ISNS Messages 2 75
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 98
    L3SS-1004 LACP Messages LACP-1001 LACP-1002 LANCE Messages LANCE-1000 LFM Messages LFM-1001 LFM-1002 LFM-1003 LFM-1004 LFM-1005 76 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 99
    -1004 MCAST_SS Messages MCAST_SS-1001 MCAST_SS-1002 MCAST_SS-1003 MCAST_SS-1004 MCAST_SS-1005 MCAST_SS-1006 MCAST_SS-1007 MCAST_SS-1008 MCAST_SS-1009 MCAST_SS-1010 MCAST_SS-1011 Fabric OS Message Reference 53-1002749-01 LOG Messages 2 77
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 100
    MPTH-1002 MPTH-1003 MQ Messages MQ-1004 MQ-1005 MQ-1006 MS Messages MS-1001 MS-1002 MS-1003 MS-1004 MS-1005 78 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 101
    -2002 MSTP-2003 MSTP-2004 MSTP-2005 MSTP-2006 NBFS Messages NBFS-1001 NBFS-1002 NBFS-1003 NBFS-1004 NS Messages NS-1001 NS-1002 Fabric OS Message Reference 53-1002749-01 MSTP Messages 2 79
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 102
    NSM-1009 NSM-1010 NSM-1011 NSM-1012 NSM-1013 NSM-1014 NSM-1015 NSM-1016 NSM-1017 NSM-1018 NSM-1019 NSM-1020 80 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 103
    -1011 PDM-1012 PDM-1013 PDM-1014 PDM-1017 PDM-1019 PDM-1020 PDM-1021 PDM-1022 PDM-1023 PDM-1024 PDM-1025 PDM-1026 Fabric OS Message Reference 53-1002749-01 ONMD Messages 2 81
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 104
    -1072 PMGR Messages PMGR-1001 PMGR-1002 PMGR-1003 PMGR-1004 PMGR-1005 PMGR-1006 PMGR-1007 PMGR-1008 PMGR-1009 PMGR-1010 PMGR-1011 PORT Messages PORT-1003 PORT-1004 PORT-1005 PORT-1006 PORT-1007 PORT-1008 PORT-1009 PORT-1010 82 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 105
    -1007 RAS Messages RAS-1001 RAS-1002 RAS-1004 RAS-1005 RAS-1006 RAS-1007 RAS-2001 RAS-2002 RAS-2003 RAS-3001 RAS-3002 Fabric OS Message Reference 53-1002749-01 PS Messages 2 83
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 106
    RKD-1002 RKD-1003 RKD-1004 RKD-1005 RMON Messages RMON-1001 RMON-1002 RPCD Messages RPCD-1001 RPCD-1002 RPCD-1003 RPCD-1004 84 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 107
    -1006 SEC-1007 SEC-1008 SEC-1009 SEC-1010 SEC-1016 SEC-1022 SEC-1024 SEC-1025 SEC-1026 SEC-1028 SEC-1029 SEC-1030 Fabric OS Message Reference 53-1002749-01 RTE Messages 2 85
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 108
    SEC-1056 SEC-1057 SEC-1059 SEC-1062 SEC-1063 SEC-1064 SEC-1065 SEC-1069 SEC-1071 SEC-1072 SEC-1073 SEC-1074 86 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 109
    -1097 SEC-1098 SEC-1099 SEC-1100 SEC-1101 SEC-1102 SEC-1104 SEC-1105 SEC-1106 SEC-1107 SEC-1108 SEC-1110 SEC-1111 Fabric OS Message Reference 53-1002749-01 SEC Messages 2 87
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 110
    SEC-1154 SEC-1155 SEC-1156 SEC-1157 SEC-1158 SEC-1159 SEC-1160 SEC-1163 SEC-1164 SEC-1165 SEC-1166 SEC-1167 88 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 111
    -1194 SEC-1195 SEC-1196 SEC-1197 SEC-1198 SEC-1199 SEC-1200 SEC-1201 SEC-1202 SEC-1203 SEC-1250 SEC-1251 SEC-1253 Fabric OS Message Reference 53-1002749-01 SEC Messages 2 89
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 112
    SEC-1323 SEC-1324 SEC-1325 SEC-1326 SEC-1327 SEC-1328 SEC-1329 SEC-1330 SEC-1331 SEC-1332 SEC-1333 SEC-1334 90 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 113
    -4001 SFLO Messages SFLO-1001 SFLO-1002 SFLO-1003 SFLO-1004 SFLO-1005 SFLO-1006 SFLO-1007 SFLO-1008 SNMP Messages SNMP-1001 SNMP-1002 Fabric OS Message Reference 53-1002749-01 SFLO Messages 2 91
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 114
    SPC-2014 SPC-2040 SPC-2041 SPC-2042 SPC-2043 SPC-2044 SPC-3001 SPC-3002 SPC-3003 SPC-3004 SPC-3005 SPC-3006 92 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 115
    -1012 SPM-1013 SPM-1014 SPM-1015 SPM-1016 SPM-3001 SPM-3002 SPM-3003 SPM-3004 SPM-3005 SPM-3006 SPM-3007 SPM-3008 Fabric OS Message Reference 53-1002749-01 SPM Messages 2 93
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 116
    SS-1000 SS-1001 SS-1002 SS-1003 SS-1004 SS-1005 SS-1006 SS-1007 SS-1008 SS-1009 SS-1010 SS-1011 94 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 117
    -1211 SSMD-1212 SSMD-1213 SSMD-1214 SSMD-1215 SSMD-1216 SSMD-1217 SSMD-1300 SSMD-1301 SSMD-1302 SSMD-1303 SSMD-1304 SSMD-1305 Fabric OS Message Reference 53-1002749-01 SSMD Messages 2 95
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 118
    SULB-1009 SULB-1010 SULB-1011 SULB-1017 SULB-1018 SULB-1020 SULB-1021 SULB-1022 SULB-1023 SULB-1024 SULB-1025 SULB-1026 96 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 119
    -1006 SWCH-1007 SWCH-1008 SWCH-1009 SWCH-1010 SWCH-1011 SWCH-1012 SWCH-1013 SWCH-1014 SWCH-1015 SWCH-1016 SWCH-1017 SWCH-1018 Fabric OS Message Reference 53-1002749-01 SWCH Messages 2 97
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 120
    SYSM-1005 SYSM-1006 SYSM-1007 TAPE Messages TAPE-1001 TRCE Messages TRCE-1001 TRCE-1002 TRCE-1003 TRCE-1004 TRCE-1005 TRCE-1006 98 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 121
    -1006 TS-1007 TS-1008 UCST Messages UCST-1003 UCST-1007 UCST-1020 UCST-1021 UCST-1022 UCST-1023 UCST-1024 UCST-1026 UCST-1027 Fabric OS Message Reference 53-1002749-01 TRCK Messages 2 99
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 122
    WEBD-1004 WEBD-1005 WEBD-1006 WEBD-1007 WEBD-1008 XTUN Messages XTUN-1000 XTUN-1001 XTUN-1002 XTUN-1003 XTUN-1004 XTUN-1005 100 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 123
    -2022 XTUN-2023 XTUN-2024 XTUN-2025 ZEUS Messages ZEUS-1001 ZEUS-1002 ZEUS-1003 ZEUS-1004 ZEUS-1005 ZEUS-1015 ZEUS-1016 ZEUS-1028 Fabric OS Message Reference 53-1002749-01 ZEUS Messages 2 101
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 124
    ZONE-1040 ZONE-1041 ZONE-1042 ZONE-1043 ZONE-1044 ZONE-1045 ZONE-1046 ZONE-1048 ZONE-1049 ZONE-1054 ZONE-1057 ZONE-1058 102 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 125
    ZONE-1059 ZONE-1060 ZONE-1061 ZONE-1062 ZONE Messages 2 Fabric OS Message Reference 103 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 126
    2 ZONE Messages 104 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 127
    -1013 AUTH Messages AUTH-1045 AUTH-1046 AUTH-1047 AUTH-3001 AUTH-3002 AUTH-3003 AUTH-3004 AUTH-3005 AUTH-3006 AUTH-3007 AUTH-3008 Fabric OS Message Reference 53-1002749-01 Chapter 3 105
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 128
    CNM-3010 CNM-3011 CNM-3012 CONF Messages CONF-1000 CONF-1020 CONF-1022 CONF-1042 CONF-1043 CONF-1044 CVLM Messages CVLM-3001 106 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 129
    -3020 CVLM-3021 CVLM-3022 CVLM-3023 CVLM-3024 CVLM-3025 CVLM-3026 CVLM-3027 CVLM-3028 ESS Messages ESS-1008 ESS-1009 ESS-1010 Fabric OS Message Reference 53-1002749-01 ESS Messages 3 107
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 130
    HAM-1015 HTTP Messages HTTP-1002 HTTP-1003 IPAD Messages IPAD-1002 LOG Messages LOG-1005 LOG-1006 LOG-1007 LOG-1008 LOG-1011 108 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 131
    PMGR Messages PMGR-1001 PMGR-1003 PORT Messages PORT-1006 PORT-1007 PORT-1008 PORT-1009 RAS Messages RAS-2001 RAS-2002 RAS-2003 RAS-3005 SEC Messages SEC-1113 SEC-1114 SEC-1337 SEC-3001 SEC-3002 SEC-3003 SEC-3004 SEC-3005 SEC-3006 SEC-3007 Fabric OS Message Reference 53-1002749-01 MS Messages
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 132
    SEC-3031 SEC-3032 SEC-3033 SEC-3034 SEC-3035 SEC-3036 SEC-3037 SEC-3038 SEC-3039 SEC-3044 SEC-3045 SEC-3046 110 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 133
    -3001 SPM-3002 SPM-3003 SPM-3004 SPM-3005 SPM-3006 SPM-3007 SPM-3008 SPM-3009 SPM-3010 SPM-3011 SPM-3012 SPM-3013 Fabric OS Message Reference 53-1002749-01 SNMP Messages 3 111
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 134
    SULB-1010 SULB-1017 SULB-1018 SULB-1020 SULB-1021 SULB-1023 SULB-1024 SULB-1026 SULB-1030 SULB-1031 SULB-1032 SULB-1033 112 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 135
    -1027 ZONE Messages ZONE-3001 ZONE-3002 ZONE-3003 ZONE-3004 ZONE-3005 ZONE-3006 ZONE-3007 ZONE-3008 ZONE-3009 ZONE-3010 ZONE-3011 Fabric OS Message Reference 53-1002749-01 SWCH Messages 3 113
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 136
    3 ZONE Messages ZONE-3012 ZONE-3013 ZONE-3014 ZONE-3015 ZONE-3016 ZONE-3017 ZONE-3018 ZONE-3019 ZONE-3020 ZONE-3021 ZONE-3022 ZONE-3023 ZONE-3024 ZONE-3025 ZONE-3026 114 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 137
    FFDC Messages ANV Messages ANV-1002 AUTH Messages AUTH-1014 AUTH-1044 BKSW Messages BKSW-1003 BL Messages BL-1002 BL-1003 BL-1004 BL-1008 BL-1009 BL-1011 BL-1016 BL-1020 BLS Messages BLS-1000 BLS-1001 BM Messages BM-1003 BM-1053 Fabric OS Message Reference 53-1002749-01 Chapter 4 115
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 138
    EM-1006 EM-1008 EM-1009 EM-1010 EM-1011 EM-1012 EM-1018 EM-1020 EM-1028 EM-1068 EM-1071 EM-1072 116 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 139
    Messages FCPH-1001 FLOD Messages FLOD-1004 HAM Messages HAM-1001 HAM-1006 HAM-1007 HAM-1008 HAM-1009 HAM-1011 HAMK Messages HAMK-1001 Fabric OS Message Reference 53-1002749-01 FABR Messages 4 117
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 140
    HMON Messages HMON-1001 KSWD Messages KSWD-1001 KSWD-1002 LFM Messages LFM-1004 LOG Messages LOG-1001 LOG-1002 LSDB Messages LSDB-1003 118 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 141
    -1004 PLAT-1072 PS Messages PS-1000 RAS Messages RAS-1004 RAS-1005 RCS Messages RCS-1012 RCS-1013 SCN Messages SCN-1001 SCN-1002 Fabric OS Message Reference 53-1002749-01 MPTH Messages 4 119
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 142
    4 SNMP Messages SNMP Messages SNMP-1004 SYSC Messages SYSC-1001 SYSC-1002 SYSM Messages SYSM-1001 SYSM-1005 SYSM-1006 TRCE Messages TRCE-1008 UCST Messages UCST-1007 WEBD Messages WEBD-1008 ZEUS Messages ZEUS-1002 120 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 143
    • Some blades and ports in a switch may not support NPIV. NPIV functionality cannot be enabled on such ports and they will not respond to NPIV requests. Refer to the Access Gateway Administrator's Guide for specific AG-compatibility requirements. • On non-Brocade switches, refer to the manufacturer
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 144
    ERROR Probable Cause Indicates that the fabric sent an invalid response to the FLOGI Extended Link Service (ELS) for the specified N_Port. Recommended Action Check the configuration of the fabric switch. If the message persists, execute the supportFtp command (as needed) to set up automatic
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 145
    Check the configuration of the fabric switch connected to the Access Gateway. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 123 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 146
    Check the configuration of the fabric switch connected to the Access Gateway. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 124 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 147
    the fabric switch. Recommended Action Check the configuration of the fabric switch connected to the Access Gateway. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 148
    or all configured N_Ports have failed to come online. Recommended Action Execute the switchShow command to display the status of all ports in the system. Execute the portCfgShow command to display the list of ports currently configured as N_Ports. 126 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 149
    for N_Port operation. Recommended Action Execute the switchShow command to display the status of all ports in the system. Execute the portCfgShow command to display the list of ports currently configured as N_Ports. Make sure the host is connected to an F_port. AG-1019 Message Unable to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 150
    Type LOG Severity WARNING Probable Cause Indicates that failover across N_Ports connected to different fabrics is not supported. Recommended Action Change the preferred N_Port settings of the specified F_Port using the ag --prefset command. Choose the preferred N_Port so that it is in the same
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 151
    and increase the number of allowed logins on the specified port. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 129 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 152
    enabled on the specified port. Recommended Action Execute the portCfgNpivPort command on the Access Gateway switch to enable the NPIV capability on the port. AG-1028 Message Device with Port WWN tried to perform fabric login through port , without having access permission
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 153
    configuration. AG-1032 Message N_Port (ID: ) has recovered from an unreliable state. Message Type LOG Severity INFO Probable Cause Indicates that the port state has been stable for the last five minutes. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 154
    login as ALPA value is not available (). Message Type AUDIT | LOG Class CFG Severity INFO Probable Cause Indicates that a device has already used the specified arbitrated loop physical address (ALPA) value. Recommended Action No action is required. 132 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 155
    is connected to a non-Brocade fabric with Persistent ALPA enabled. Check the admin guide for supported configuration. Message Type AUDIT | LOG Class CFG Severity WARNING Probable Cause Indicates that one of the ports is connected to a non-Brocade fabric. Recommended Action Refer to the Access
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 156
    monitor configuration as it might not be functional. Message Type LOG Severity WARNING Probable Cause Indicates that N_Port ID virtualization (NPIV) assigns a new port ID (PID) each time the same port is disabled and then re-enabled. As the PID has changed, the end-to-end (EE) monitors installed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 157
    Access Gateway is using firmware earlier than Fabric OS v7.1.0. Recommended Action Check the authentication configuration of the edge switch using the authutil --show command. AG-1044 Message Port has been disabled because switch requires authentication when device authentication
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 158
    using the memShow command. Restart or power cycle the switch. AN-1002 Message Failed to initialize; rc = . Message Type LOG Severity ERROR Probable Cause Indicates that the initialization of the "trafd" daemon has failed. Recommended Action Download a new firmware version using the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 159
    credits to service the link distance. AN-1004 Message Congestion bottleneck on port /
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 160
    port are used by port mirroring. Recommended Action Contact your switch service provider for assistance. AN-1012 Message Credits did not return from other end. Complete loss of credits on a VC on slot port . Message Type LOG | AUDIT Class FABRIC
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 161
    link reset to recover the port credits on slot port . Message Type LOG | AUDIT Class FABRIC Severity INFO Probable Cause Indicates a credit loss. Recommended Action The port is recovered. No action is required. Fabric OS Message Reference 139
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 162
    peer ports. Recommended Action Verify that compatible SFP transceivers are used on the peer ports, ASIC) hardware that may degrade the data traffic. Recommended Action Restart the system at the next maintenance window. If the problem persists, replace the blade. 140 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 163
    ASIC) hardware that may degrade the data traffic. Recommended Action Restart the system at the next maintenance window. If the problem persists, replace the problem persists, replace the switch or contact your switch service provider. ANV-1006 Message S,C: HW ASIC Chip
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 164
    the specified port is re-initialized due to link reset failure. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. 142 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 165
    is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. ANV-1028 Message Detected excessive Link resets on the port in a second. Slot , Port (). Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 166
    transfers; then execute the supportSave command and contact your switch service provider. AUTH-1003 Message type has been successfully set to . Message Type LOG Severity INFO Probable Cause Indicates that an authentication configuration value was set to a specified
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 167
    command has failed to set the authentication configuration value. The data command and contact your switch service provider. AUTH-1006 Message Failed to open authentication configuration file. Message Type LOG Severity WARNING Probable Cause Indicates an internal problem with the Secure Fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 168
    an internal problem with the Secure Fabric OS. Recommended Action Reboot or power cycle the switch. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 146 Fabric OS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 169
    and portEnable commands or the switchDisable and switchEnable commands. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 147 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 170
    using the supportShow command, and contact your switch service provider. AUTH-1017 Message Invalid value to start authentication request: port , operation code . Message Type LOG Severity ERROR Probable Cause Indicates an internal problem with the Secure Fabric OS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 171
    the supportSave command and contact your switch service provider. AUTH-1020 Message Failed to create timer for authentication: port . Message Type LOG Severity INFO Probable Cause Indicates that an authentication message timer was not created. Usually this problem is transient
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 172
    and portEnable commands or the switchDisable and switchEnable commands. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 150 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 173
    authentication phase. This indicates that the local switch does not support the specified authentication value. Recommended Action Check the authentication configuration and reset the supported value if needed using the authUtil command. Reinitialize authentication using the portDisable and
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 174
    supportSave command and contact your switch service provider. AUTH-1031 Message Failed to retrieve secret value: port . Message Type LOG Severity ERROR Probable Cause Indicates that the secret value was not set properly for the authenticated entity. 152 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 175
    execute the supportSave command and contact your switch service provider. AUTH-1033 Message Disable port due to unauthorized switch . Message Type LOG Severity ERROR Probable Cause Indicates that an entity was not configured in the Switch Connection Control (SCC
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 176
    and portEnable commands or the switchDisable and switchEnable commands. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 154 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 177
    needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. AUTH-1039 Message Neighboring switch has conflicting authentication policy: Port disabled. Message Type LOG Severity ERROR Probable Cause Indicates that the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 178
    Action If the port is disabled, correct the switch policy configuration on either of the switches using the authUtil command, and then enable the port on the neighboring switch using the portEnable command. If the E_Port has formed, no action is required. AUTH-1041 Message Port has
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 179
    not present in this switch in port . Message Type AUDIT | LOG Class SECURITY Severity ERROR Probable Cause Indicates that the public key infrastructure (PKI) certificate is not installed in this switch. Fabric OS Message Reference 157 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 180
    ". Recommended Action Execute the secAuthCertificate command again. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 158 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 181
    (PKI) objects were created using the secCertUtil command or that the PKI objects were removed using the secCertUtil delete -fcapall command. Operation type can be either "Created" or "Removed". Recommended Action No action is required. Fabric OS Message Reference 159 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 182
    port is disabled, correct the switch policy configuration on either of the switches using the authUtil command, and then enable the port on the neighboring switch using the portEnable command. If the E_Port formed, no action is required failed on the specified port due to mismatched response values
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 183
    authentication using the portDisable and portEnable commands. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 161 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 184
    daemons is found to be nonresponsive; sending signal abort (SIGABRT). Recommended Action Execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 162 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 185
    ; then power cycle the blade using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. Additional blade fault messages precede and follow this error, providing more information. Refer to other
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 186
    -On Self-Test (POST) is enabled; then power cycle the blade using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. If the message persists, replace the blade. BL-1006 Message Blade
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 187
    is required. The power cycle the blade using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. If the message persists, replace ASIC) chips. Fabric OS Message Reference 165 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 188
    slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. On a non-bladed switch, reboot or power cycle the switch. If the message persists, replace the blade or the (non-bladed) switch. 166 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 189
    ) transceiver, or device attached to the specified port. On a bladed switch, run the slotPowerOff and slotPowerOn commands to power cycle the blade. On a non-bladed switch, reboot or power cycle the switch. If the message persists, replace the blade. Fabric OS Message Reference 167 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 190
    any hardware problems. On a non-bladed switch, execute the reboot command to restart the switch. If there is a hardware error, the slotPowerOff or slotPowerOn fails on the bladed switch, or errors are encountered again, replace the blade or the (non-bladed) switch. 168 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 191
    -On Self-Test (POST) is enabled; then power cycle the blade using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. If the message persists, replace the blade. BL-1017 Message Slot
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 192
    the application-specific integrated circuit (ASIC) chips. Recommended Action Reboot or power cycle the switch. If the message persists, replace the switch. BL-1021 Message Retry , internal port retry initialization, . Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 193
    completed. Recommended Action Reboot or power cycle the blade using the slotPowerOff and slotPowerOn commands. If the message persists, replace the blade. BL-1024 Message All ports on the blade in slot will be reset as part of the firmware upgrade. Message Type LOG Severity INFO
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 194
    . As part of the upgrade, all the Gigabit Ethernet, Fibre Channel over IP (FCIP), virtualization data elements, and FC Fastwrite ports were reset. Recommended Action No action is required. BL-1026 Message Internal port offline during warm recovery, state (0x). Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 195
    switch internal processor firmware to be upgraded and resulted in the cold upgrade. As part of the upgrade, all Gigabit Ethernet, Fibre Channel over IP (FCIP), virtualization data elements, and FC Fastwrite ports were reset. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 196
    ) is enabled; then power cycle the blade using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. If the message persists, replace the blade. 174 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 197
    Channel (FC) ports. Recommended Action No action is required. BL-1035 Message Slot iSCSI port execute the slotPowerOff or slotPowerOn commands on the 8 Gbps blade. All EX_Ports and VEX_Ports can be re-enabled. Fabric OS Message Reference 175 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 198
    ; then power cycle the blade using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. Additional blade fault messages precede and follow this error, providing more information. Refer to other
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 199
    does not support dynamic area mode on the default switch. Recommended Action Turn off the dynamic area mode using the configure command. BL- problem accessing the data. Recommended Action Reseat the SFP transceiver. If problem persists, replace the SFP transceiver. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 200
    the interop mode is turned on in the default switch while powering on the FCoE blade. Recommended Action Disable the interop mode using the interopmode command; then execute the slotPowerOff and slotPowerOn commands on the FCoE blade. BL-1049 Message Serdestunemode: . Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 201
    ) version with Fabric OS v7.0.0 is incompatible on the FX8-24 blade. Recommended Action Contact your switch service provider for upgrade instructions. BL-1051 Message Incompatible Blade Processor FPGA version with FOS7.0 firmware on 7800. Contact support for upgrade instructions. Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 202
    > of GE failed. Please retry the command. Data: inst= st= rsn= fn= oid=. Message Type LOG | FFDC Severity ERROR Probable Cause Indicates that the hardware is not responding to a command request, possibly
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 203
    slot () port () tunnel (). Message Type LOG Severity INFO Probable Cause Indicates that the Fabric OS version on the remote end of the tunnel does not support Tape Read Pipelining. Recommended Action No action is required. BLS-1005
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 204
    command. Refer to the release notes to determine whether a non-disruptive firmware download is supported between the revisions. Because the AP and CP blades cannot communicate, it is not possible to load new firmware on the AP blade. If necessary, send the AP blade back to the factory for a firmware
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 205
    from the control processor (CP) firmware due to a firmware upgrade. • The blade was recently inserted and had a different version of the firmware loaded. Recommended Action No action is required. The blade will automatically download the updated firmware. BM-1005 Message Firmwaredownload timed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 206
    . Faulting switch. Message Type LOG Severity WARNING Probable Cause Indicates that the firmware download on the application processor (AP) blade failed. Recommended Action Execute the slotPowerOff and slotPowerOn commands or reseat the affected blade. 184 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 207
    control processor (CP) firmware due to a firmware upgrade. • The blade was recently inserted and had a different version of the firmware loaded. Recommended Action No action is required. The blade will automatically download the updated firmware. Fabric OS Message Reference 185 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 208
    Cause Indicates that firmware download on the application processor (AP) blade has failed. Recommended Action Execute the slotPowerOff and slotPowerOn commands or reseat the affected blade. BM-1056 Message AP is not configured. Persistently disabling all ports on the switch. Message Type LOG
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 209
    Cause Indicates an internal error in the application-specific integrated circuit (ASIC) hardware that may degrade the data traffic. Recommended Action Restart the system at the next maintenance window. If the problem persists, replace the blade. Fabric OS Message Reference 187 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 210
    No action is required. C2-1007 Message S,P(): best effort QoS will be turned off at next port state change as it is not supported under this configuration Message Type LOG Severity WARNING Probable Cause Indicates that quality of service (QoS) will
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 211
    on that port for two seconds. Recommended Action Turn on the back-end credit recovery to reset the link and recover the lost credits. If credit recovery has already been turned on, the link will be reset to recover the credits and no action is required. Fabric OS Message Reference 189 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 212
    the specified port is re-initialized due to link reset failure. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. 190 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 213
    is faulted because the link reset threshold value has exceeded. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. Fabric OS Message Reference 191 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 214
    ASIC) hardware that may degrade the data traffic. Recommended Action Restart the system at the next maintenance window. C2-1025 Message S,P(
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 215
    is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. C2-1028 Message Detected excessive Link resets on the port in a second. Slot , Port (). Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 216
    Cause Indicates an internal error in the application-specific integrated circuit (ASIC) hardware that may degrade the data traffic. Recommended Action Reboot the system at the next maintenance window. If the problem persists, replace the blade. 194 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 217
    effort QoS will be turned off at next port state change as it is not supported under this configuration. Message Type LOG Severity WARNING Probable Cause Indicates that quality of service (QoS) will be turned off automatically at the next port state change because best effort QoS is no longer
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 218
    channel (VC) and port. Recommended Action Turn on the back-end credit recovery to reset the link and recover the lost credits. If credit recovery has already been turned on, the link will be reset to recover the credits and no action is required. 196 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 219
    that one or more credits were lost and the link is reset. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. Fabric OS Message Reference 197 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 220
    of the unavailability of the ports in the internal trunk. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. 198 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 221
    the link reset threshold value has exceeded. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. C3-1019 Message S,C: HW ASIC Chip TXQ
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 222
    in hardware that may or may not impact the data traffic. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. C3-1025 Message S,P
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 223
    is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. C3-1028 Message Detected excessive Link resets on the port in a second. Slot , Port (). Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 224
    the specified remote domain requested the local domain to be disabled. Recommended Action Check the error message log on the remote domain using the errShow command to find the reason. 202 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 225
    a module within the Converged Enhanced Ethernet (CEE) configuration management daemon has failed. Recommended Action Download a new firmware version using the firmwareDownload command. CCFG-1002 Message Started loading CEE system configuration. Message Type AUDIT | LOG Class CFG Severity INFO
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 226
    running configuration file has been updated. Recommended Action No action is required. CCFG-1007 Message Startup configuration is deleted. Message Type LOG Severity INFO Probable Cause Indicates that the startup configuration file has been moved or deleted. 204 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 227
    Message Current system running configuration file is updated partially. Message Type LOG Severity INFO Probable Cause Indicates that the current running configuration file has been updated partially. Recommended Action No action is required. Fabric OS Message Reference 205 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 228
    and slotPowerOn commands on the specified slot to bring the blade online. CCFG-1013 Message . Message Type AUDIT Class CFG Severity INFO Probable Cause Indicates that the switch state has changed. Recommended Action No action is required. 206 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 229
    Cause Indicates an internal error in the application-specific integrated circuit (ASIC) hardware that may degrade the data traffic. Recommended Action Restart the system at the next maintenance window. If the problem persists, replace the blade. Fabric OS Message Reference 207 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 230
    the application-specific integrated circuit (ASIC) hardware that may degrade the data traffic. Recommended Action Restart the system at the next maintenance window. If the problem persists, replace the blade. CDR-1005 Message S,P(): best effort QoS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 231
    Severity WARNING Probable Cause Indicates that some errors were found in hardware that may or may not impact the data traffic. Recommended Action No action is required. CDR-1008 Message S,C: HW ASIC Chip warning Level 1 type = 0x. Message Type LOG
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 232
    in hardware that may or may not impact the data traffic. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. CDR-1011 Message S,P
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 233
    that the specified port is faulted due to port re-initialization failure. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. Fabric OS Message Reference 211 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 234
    because the link reset threshold is exceeded. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. CDR-1019 Message S,C: HW ASIC Chip TXQ
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 235
    in hardware that may or may not impact the data traffic. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. CDR-1028 Message Detected excessive Link resets on
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 236
    that the specified blade has failed during failover or recovery. Recommended Action For a bladed switch, execute the slotPowerOff and slotPowerOn commands to power cycle the blade. For a non-bladed switch, restart or power cycle the switch. 214 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 237
    diagnostic blade attach operation has failed during failover or recovery. Recommended Action For a bladed switch, execute the slotPowerOff and slotPowerOn commands to power cycle the blade. For a non-bladed switch, restart or power cycle the switch. Fabric OS Message Reference 215 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 238
    command. Restart or power cycle the switch. CNM-1002 Message Failed to initialize rc = . Message Type LOG Severity ERROR Probable Cause Indicates that the initialization of a module within the Cluster Node Manager (CNM) has failed. Recommended Action Download a new firmware
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 239
    Severity INFO Probable Cause Indicates that the crypto service is enabled or disabled on the switch. Recommended Action No action is required. CNM-1005 Message Posting event CNM_EVT_GRP_LEADER_ELECTED Name [], WWN []. Message Type LOG Severity INFO Probable Cause Indicates
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 240
    No action is required. CNM-1010 Message Posting event CNM_EVT_CLUSTER_UDATA_UPDATE cid [], ulen []. Message Type LOG Severity INFO Probable Cause Indicates the client data update. Recommended Action No action is required. 218 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 241
    event CNM_EVT_NODE_JOIN_TIMEOUT nodeName [], WWN [], ipaddress []. Message Type is deleted. Recommended Action No action is required. CNM-1013 Message Posting event GL Node is split. Recommended Action No action is required. CNM-1014 Message Posting event Node Admission
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 242
    from un-recognized GL node [], configured GL node is []. Message Type LOG Severity INFO Probable Cause Indicates a join request was received from an invalid group leader (GL) node. Recommended Action No action is required. 220 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 243
    Type LOG Severity INFO Probable Cause Indicates an invalid member node certificate. Recommended Action Install a valid certificate and add member node to the group leader (GL) node, or has failed. Recommended Action No action is required. Fabric OS Message Reference 221 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 244
    not allowed in group leader (GL) node. Recommended Action No action is required. CNM-1024 Message Operation not required on GL node. Message Type LOG Severity INFO Probable Cause Indicates an operation is not required on a group leader (GL) node. 222 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 245
    mismatch, Recvd Hdr version 0x Exp Hdr version 0x Node . Message Type LOG Severity INFO Probable Cause Indicates that a version mismatch has occurred. Recommended Action Upgrade the firmware or delete the node from the Encryption
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 246
    exists. Recommended Action No action is required. CNM-1029 Message Certfile
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 247
    Indicates that the cluster is in a degraded state. Recommended Action No action is required. CNM-1034 Message All the defined nodes in the Encryption Group are ONLINE. Cluster is in a converged state. Recommended Action No action is required. Fabric OS Message Reference 225 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 248
    posted to specify the cluster is in a degraded state. Recommended Action No action is required. CNM-1036 Message All the active nodes of the cluster are in ONLINE state. split-brain arbitration is lost. Recommended Action No action is required. 226 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 249
    is won. Recommended Action No action is required. CNM-1041 Message Updating persistent Cluster DB, please avoid powering off the switch. Message Type LOG Severity INFO Probable Cause Indicates the system is updating the persistent database. Fabric OS Message Reference 227 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 250
    HBT from undefined node IpAddress [], WWN []. Possible configuration error. Message Type LOG Severity ERROR Probable Cause Indicates that the remote node's WWN may be changed. Recommended Action No action is required. CNM-1044 Message Cluster Create Failed as the Certificate files
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 251
    Cause Indicates that the member node with dual IP stack was registered with the IPv6 Encryption Group (EG). Recommended Action No action is required. CNM-1046 Message Posting event CNM_EVT_NODE_LEAVE nodeName [], WWN []. Message Type LOG Severity INFO Probable Cause Indicates
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 252
    mode mismatch, ensure mode settings are same across all nodes in EG. Message Type LOG Severity ERROR Probable Cause Indicates mode mismatch between the switches, such as the Access Gateway mode mismatch. Recommended Action No action is required. 230 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 253
    the operation. CNM-1054 Message Encryption Group database state [] with node IP [], WWN []. Message Type LOG Severity INFO Probable Cause Indicates the status of the cluster database. Recommended Action No action is required. Fabric OS Message Reference 231 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 254
    event CNM_EVT_ONLINE Slot [], WWN [], IP [], flags []. Message Type LOG Severity INFO Probable Cause Indicates that the encryption engine is online in the Encryption Group (EG). Recommended Action No action is required. 232 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 255
    pair is matched. Recommended Action No action is required. CNM-1061 Message IP of the switch changed from [] to []. Message Type LOG Severity INFO Probable Cause Indicates that the switch IP address has changed. Fabric OS Message Reference 233 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 256
    that the certificate was copied to the file with new IP name. Recommended Action No action is required. CNM-3001 Message Event: cryptocfg Status: success, Info: encryption group \"\" created. Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 257
    member node was added to an encryption group. Recommended Action No action is required. CNM-3004 Message Event: cryptocfg Status: success, Info: Membernode \"\" left an encryption group. Recommended Action No action is required. Fabric OS Message Reference 235 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 258
    Probable Cause Indicates that the heartbeat timeout value was set. Recommended Action No action is required. CNM-3008 Message Event: cryptocfg Status: success, Info: Routing mode of EE mode was set. Recommended Action No action is required. 236 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 259
    that the specified member node was unregistered. Recommended Action No action is required. CNM-3011 Message Event: cryptocfg Status: success, Info: Encryption group an encryption group was synchronized. Recommended Action No action is required. Fabric OS Message Reference 237 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 260
    if LUNs are set up for encryption. Recommended Action Preserve the EG name when EG is recreated if LUNs are set up for encryption. 238 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 261
    and AD variable is the description of the classes of configuration parameters that were downloaded. If Admin Domain (AD) is enabled, the AD number is the errShow command to view the error log. Correct the error and execute the configDownload command again. Fabric OS Message Reference 239 53-
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 262
    that require the switch to be disabled. Recommended Action Disable the switch using the switchDisable command and download the configuration. CONF errShow command to view the error log. Correct the error and execute the configDownload command again. 240 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 263
    system. CONF-1031 Message configDefault completed successfully . Message Type LOG Severity INFO Probable Cause Indicates that the configDefault command was initiated and completed successfully. Recommended Action No action is required. Fabric OS Message Reference 241 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 264
    the configRemove command was initiated and completed successfully. Recommended Action No action is required. CONF-1040 command. Recommended Action Execute the errShow command to view the error log. Correct the error and execute the configRemove command again. 242 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 265
    > changed from to Message Type LOG | AUDIT Class CFG Severity INFO Probable Cause Indicates that the fabric configuration parameter value has been changed by a user. Recommended Action No action is required. Fabric OS Message Reference 243 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 266
    key acquisition process for each pool. Recommended Action Do not start tape backup or restore operations involving tape pools until the process is complete. 244 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 267
    Initiator: , LUN ID: . Message Type LOG Severity INFO Probable Cause Indicates that the encryption LUN policy was forcefully changed while a re-key session was still active. Recommended Action No action is required. Fabric OS Message Reference 245 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 268
    physical WWN>. Message Type LOG Severity WARNING Probable Cause Indicates that there is more than one LUN serial number discovered from the same target. Therefore, encryption on this target is disabled. Recommended Action No action is required. 246 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 269
    device type (Disk/Tape)>. Container: , Initiator: , LUN ID: . Message Type LOG Severity ERROR Probable Cause Indicates that LUN discovery failed. Recommended Action No action is required. Fabric OS Message Reference 247 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 270
    Message Third party license is required for encryption LUN in third party mode. Container: , Initiator: , LUN ID: . Message Type LOG Severity ERROR Probable Cause Indicates that the encryption LUN is configured with non-Brocade mode but
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 271
    >, Initiator: , LUN ID: . Message Type LOG Severity INFO Probable Cause Indicates that the LUN is set to read-only mode because there is a conflict in the configuration. Recommended Action No action is required. Fabric OS Message Reference 249 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 272
    : . Container: , Initiator: , LUN ID: . Message Type LOG Severity INFO Probable Cause Indicates an informational event. Recommended Action No action is required. 250 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 273
    : , LUN ID: . Message Type LOG Severity ERROR Probable Cause Indicates that the data state in the LUN configuration is cleartext, but metadata exists on the LUN. Recommended Action Use the cryptoCfg command to confirm the configuration. CVLC-1020 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 274
    , Initiator: , LUN ID: . Message Type LOG Severity INFO Probable Cause Indicates that the device decommission process has either succeeded or failed. Recommended Action No action is required. 252 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 275
    contain any metadata. Container: , Initiator: , LUN ID: . Message Type LOG Severity ERROR Probable Cause Indicates that the metadata was corrupted. Recommended Action No action is required. Fabric OS Message Reference 253 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 276
    LUN. Recommended Action Perform the following steps. 1. Make the target ports of the mirror LUN offline to hosts. 2. Re-establish the mirror. 3. After the mirror is in sync, split the mirror. 4. Bring back the target ports of the mirror LUN online. 254 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 277
    No action is required. CVLC-1033 Message Rebalance completed for EE: . Device login in progress. Message Type LOG Severity INFO Probable Cause Indicates that a rebalance operation was performed. Recommended Action No action is required. Fabric OS Message Reference 255 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 278
    first-time encryption, key expired, or manual re-key operation failed. Recommended Action No action is required. CVLC-1035 Message A decommissioned LUN has been added back as encrypted LUN. Container: , Initiator: , LUN ID: . Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 279
    name>, Initiator: , LUN ID: . Message Type LOG Severity WARNING Probable Cause Indicates that the host write operation on secondary metadata block region failed. Recommended Action Disable the initiator port. Fabric OS Message Reference 257 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 280
    of a module within the Crypto Virtual LUN Manager (CVLM) daemon has failed. Recommended Action Download a new firmware version using the firmwareDownload command. CVLM-1003 Message Crypto device configuration has been committed by switch (). Message Type LOG Severity INFO Probable
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 281
    configuration in the cluster group using the cryptocfg --commit command. CVLM-1005 Message Crypto service is on the switch. Message Type LOG Severity INFO Probable Cause Indicates that the crypto service is enabled or disabled on the switch. Recommended Action No action is required
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 282
    is not configured. Message Type LOG Severity WARNING Probable Cause Indicates that the IP address of the encryption engine IO link is not configured. Recommended Action Configure the encryption engine IO link IP address using the ipAddrSet command. 260 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 283
    engine. Recommended Action No action is required. CVLM-1012 Message The HAC failback occurs at EE ( ). Message Type Recommended Action Create the Layer 2 zone for host and target and run the cryptocfg --commit command again. Fabric OS Message Reference 261
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 284
    there is no corresponding Layer 2 zone present, but IT pair is in crypto configuration. Recommended Action Disable the target access to the host, recreate the Layer 2 zone for host and target, and run the cryptocfg --commit command again to recreate the RD zone. CVLM-1015 Message Unable to read
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 285
    INFO Probable Cause Indicates that the specified HA cluster was created. Recommended Action No action is required. CVLM-3003 Message Event: cryptocfg Status: success, Info: HA cluster was deleted. Recommended Action No action is required. Fabric OS Message Reference 263 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 286
    / replaced with new node WWN/slot: / . Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates that an HA cluster member was replaced. Recommended Action No action is required. 264 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 287
    Indicates that the specified crypto-target container was created. Recommended Action No action is required. CVLM-3008 Message Event: cryptocfg Status: a manual failback was performed to an encryption engine. Recommended Action No action is required. Fabric OS Message Reference 265 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 288
    was added to a crypto-target container. Recommended Action No action is required. CVLM-3012 Message Event: cryptocfg Status: success, Info: Initiator \"
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 289
    a LUN was added to a crypto-target container. Recommended Action No action is required. CVLM-3014 Message Event: cryptocfg Status: success, Info: LUN , from the crypto-target container. Recommended Action No action is required. Fabric OS Message Reference 267 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 290
    INFO Probable Cause Indicates that the specified tape pool was created. Recommended Action No action is required. CVLM-3018 Message Event: cryptocfg Status: success, Info: tape pool was deleted. Recommended Action No action is required. 268 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 291
    Message Event: cryptocfg Status: success, Info: Manual rekey all performed. Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates that a complete manual re-key was performed. Recommended Action No action is required. Fabric OS Message Reference 269 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 292
    that a resume re-key was performed. Recommended Action No action is required. CVLM-3023 Message Event: cryptocfg Status: success, Info: Transaction committed. transaction abort operation was performed. Recommended Action No action is required. 270 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 293
    operation has failed for the device. Recommended Action Run the cryptocfg --decommission command. CVLM-3027 Message Event: cryptocfg Status: success, Info: Decommission of been completed for the device. Recommended Action No action is required. Fabric OS Message Reference 271 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 294
    : cryptocfg Status: success, Info: SRDF mode set to . Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates that the Symmetrix Remote Data Facility (SRDF) mode was set. Recommended Action No action is required. 272 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 295
    Action No action is required. DOT1-1003 Message 802.1X is enabled for port . Message Type LOG Severity INFO Probable Cause Indicates that 802.1X is enabled on the specified port. Recommended Action No action is required. DOT1-1001 5 Fabric OS Message Reference 273 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 296
    failed on the specified port due to incorrect credentials or the remote authentication dial-in user service (RADIUS) server is not functioning properly. Recommended Action Check the credentials configured with the supplicant and the RADIUS server. 274 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 297
    command. Recommended Action No action is required. DOT1-1009 Message 802.1X is disabled for port . Message Type LOG Severity INFO Probable Cause Indicates that 802.1X is disabled on the specified port. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 298
    5 DOT1-1010 DOT1-1010 Message Port is set in auto mode. Message Type LOG Severity INFO Probable Cause Indicates that the specified port is set to auto mode. Recommended Action No action is required. 276 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 299
    several types of double data rate (DDR) memory errors. Single bit errors are corrected, but other errors indicate either software errors or problems with the target system DRAM error types should be reported to technical support for further action. Fabric OS Message Reference 277 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 300
    enabled; then power cycle the blade by using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. For the Brocade 300 and 6510, replace the switch. 278 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 301
    low. Recommended Action If this problem occurs on a blade, it usually indicates a hardware problem on the blade; replace the blade. If this problem occurs on a switch, it usually indicates a hardware problem on the main board; replace the switch. Fabric OS Message Reference 279 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 302
    blade is incompatible, upgrade the firmware or replace the blade and make sure the replacement blade is compatible with your control processor (CP) type and firmware. If the incompatibility is with the logical switch configuration, change the configuration by using the lscfg command to be consistent
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 303
    message. There are serious internal Fabric OS configuration or hardware problems on the switch. Recommended Action Reseat the specified field-replaceable unit (FRU). If the problem persists, restart or power cycle the switch. Execute the diagPost command to make sure that Power-On Self-Test (POST
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 304
    checks during a cold boot. Recommended Action Monitor the switch. If the problem persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 282 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 305
    availability (HA) synchronization of the CPs will not be allowed. Recommended Action Change the chassis configuration option to 1 using the chassisConfig command, or upgrade the firmware on the standby CP to the version running on the active CP. Fabric OS Message Reference 283 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 306
    hardware problem. The FRU ID value is composed of a FRU type string and an optional number to identify the unit, slot, or port. Recommended Action If the problem persists, restart or power cycle the switch. If the problem still persists, replace the WWN card, or the switch (for non-bladed switches
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 307
    replaceable unit (FRU) is intended for use. Refer to the appropriate Hardware Reference Manual for instructions on inserting the switch no action is required for the standby command) to determine the cause of the error state. Reseat the field-replaceable unit (FRU). If the problem persists, replace
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 308
    specified field-replaceable unit (FRU) is not present on the switch. If the FRU is a World Wide Name (WWN) card, the default WWN and IP addresses are used for the switch. Recommended Action Reseat the FRU. If the problem persists, restart or power cycle the switch. Execute the diagPost command to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 309
    (on or off)>. Message Type LOG Severity WARNING Probable Cause Indicates that the specified field-replaceable unit (FRU) cannot be powered on or off. Recommended Action The specified FRU is not responding to the commands and should be replaced. Fabric OS Message Reference 287 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 310
    down because of the (predicted) failure of the power supply. • Down - A newly inserted port blade was not powered on because there was not enough power available. Recommended Action The Brocade 24000 requires only a single power supply for a fully populated chassis; however, you must always
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 311
    ) is not supported on that chassis (backplane revision D2). Remove the blade from the chassis. If the error is due to the switch configuration, the logical switch configuration of the blade is incorrect. Execute the lscfg command to correct the switch or port configuration for the ports on the blade
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 312
    ) parity error. Recommended Action No action is required if the switch does not reach the reset threshold for the switch or blade. If the reset threshold is reached on the switch or blade, the switch or blade will be faulted and should be replaced. 290 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 313
    with the switch configuration software. The blade will not be completely usable. The blade may only be supported by a later (or earlier) version of the firmware. Recommended Action Change the control processor (CP) firmware or replace the blade. Make sure the replacement is compatible with your
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 314
    blade in the system is not supported by the firmware on the standby control processor (CP). Recommended Action Remove all blades of the specified type or upgrade the standby CP. After an in the system. Recommended Action Remove the faulted blade. 292 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 315
    blade processor firmware (BFOS) is not compatible with the Storage Application Services (SAS) or other application firmware versions. Recommended Action Upgrade the Fabric OS firmware or the SAS firmware by using the firmwareDownload command. Refer to the release notes for a compatible version of
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 316
    may be indicated in other messages or debug data. There are serious internal Fabric OS configuration or hardware problems on the switch. Recommended Action Restart or power cycle the switch. If the problem persists, execute the supportFtp command (as needed) to set up automatic FTP transfers
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 317
    , or powered off. There must be at least one core blade in enabled state for the chassis to be considered ready. Recommended Action Insert and close the ejector switch on missing core blades. Reseat or replace core blades that are faulted or powered off. Fabric OS Message Reference 295 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 318
    ; then power cycle the blade by using the slotPowerOff and slotPowerOn commands or have the blade's ejector switch cycled to run POST and verify that the blade does not have any hardware problems. • On bladed systems, replace the specified FRU; otherwise, replace the switch. 296 Fabric OS Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 319
    firmware download, identify the down-level switch or switches that do not support the Coordinated HotCode protocol, and upgrade the down-level switches. Then, restart the firmware download on this switch. Note that upgrading a down-level Brocade switch in a mixed interop fabric may still cause data
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 320
    which prevented the protocol from completing. Any data traffic disruption observed during the firmware download may have been due to this issue. Recommended Action No action is required. ESS-1008 Message Fabric Name - configured (received from domain ). Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 321
    name and set it again from any switch. ESS-1010 Message Duplicate Fabric Name - matching with FID . Message Type AUDIT | LOG Class FABRIC Severity WARNING Probable Cause Indicates that the configured fabric name is already used for another partition. Recommended
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 322
    slot state has been detected as inconsistent during failover or recovery. Recommended Action For a bladed switch, execute the slotPowerOff and slotPowerOn commands to power cycle the blade. For a non-bladed switch, restart or power cycle the switch. 300 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 323
    (CP) does not support N_Port ID Virtualization (NPIV) functionality, but the switch has some NPIV devices logged in to the fabric. Recommended Action Load a firmware version on the standby CP that supports NPIV functionality using the firmwareDownload command. Fabric OS Message Reference 301 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 324
    with the port configuration that already has the area swapped. Recommended Action Replace the blade with ports that support port swap. Then swap ports back to the port's default area. Refer to the Fabric OS Administrator's Guide for more information. 302 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 325
    Probable Cause Indicates that the event could not be sent to remote proxy. This could happen if the remote proxy switch cannot be reached through in-band. Recommended Action Make sure that the specified remote domain is present in the fabric. Fabric OS Message Reference 303 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 326
    in the switches at both ends of the link. Run the configure command to modify the appropriate switch parameters on both the local and remote switch. FABR-1002 Message fabGaid: no free multicast alias IDs. Message Type LOG Severity WARNING Probable Cause Indicates that the fabric does not
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 327
    Recommended Action No action is required. This message is often transitory. If the message persists, run the supportFtp command (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Fabric OS Message Reference 305 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 328
    a problem with the Fabric OS. required if the message appears with the FABR-1005 message. If the message persists, run the supportFtp command (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. 306 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 329
    rare and usually indicates a problem with the Fabric OS. Recommended Action If the message persists, run the supportFtp command (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Fabric OS Message Reference 307 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 330
    Run the configShow command to view the fabric.ididmode. A 0 means the IDID mode is disabled; a 1 means it is enabled. Set the switch to insistent domain ID mode. This mode is set under the configure command or in Web Tools on the Switch Admin > Configure window. 308 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 331
    fabric and the configure command to change the insistent domain ID mode. Refer to the Fabric OS Command Reference for more information on these commands. FABR-1016 Message ficonMode is enabled. Message Type LOG Severity WARNING Probable Cause Indicates that FICON mode is enabled on the switch
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 332
    OS Command Reference for more information about the fabricPrincipal command. FABR-1019 Message Critical fabric size () exceeds supported configuration (). Message Type FFDC | LOG Severity CRITICAL Probable Cause Indicates that this switch is a value-line
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 333
    must be added or the size of the fabric must be changed to within the licensed limit. Contact your switch provider to obtain a full fabric license. FABR-1023 Message Fabric size is within supported configuration (). Fabric limit timer () stopped at
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 334
    fixed, based on the port configuration information. In this mode, the buffer credits are negotiated as part of exchange link parameter (ELP) exchange. This mode also uses the R_RDY primitive for flow control. Recommended Action No action is required. FABR-1030 Message fabric: Domain
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 335
    use the same area. Recommended Action Move the cable to a port area that is not in use, or disable Trunk Area. You must manually enable the port or the port remains disabled forever. Refer to the Fabric OS Administrator's Guide for more information. Fabric OS Message Reference 313 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 336
    Trunk Area. You must manually enable the port or the port remains disabled forever. Refer to the Fabric OS Administrator's Guide for more information. FABR-1036 Message F_Port trunks are only allowed on Trunk Area enabled port. Persistently disabling port . Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 337
    . Persistently disabling port . Message Type LOG Severity INFO Probable Cause Indicates that the speed is not compatible for F_Port trunks. Recommended Action Change the speed for the port or disable F_Port trunking on the port. Fabric OS Message Reference 315 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 338
    (FID) conflict with the local switch. All E_Ports directly connected to the conflicting switch are disabled. Recommended Action Make sure that all the switches in the fabric have the same FID or upgrade the switch firmware to a VF-capable firmware. 316 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 339
    . Recommended Action Make sure that all the switches in the fabric have the same Base Switch attribute or upgrade the switch firmware to a VF-capable firmware. FABR-1047 Message Area unavailable to assign to the port. Persistently disabling port . Message Type LOG
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 340
    . F_Port trunking cannot be enabled on port(). Message Type LOG Severity INFO Probable Cause Indicates that the trunking or Server Application Optimization (SAO) license is not installed. Recommended Action Install the license required. 318 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 341
    Type LOG Severity CRITICAL Probable Cause Indicates that the configuration keys have interopmode parameters such as switch.interopMode and switch.mcdtFabricmode set. Recommended Action Execute the interopmode command to reset the parameters. Fabric OS Message Reference 319 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 342
    of the port with all other ports intended to be part of the same trunk group. Use the porttrunkarea --show to identify the trunk members of the specified F_Port and the portcfgshow command to identify the conflicting configuration between the trunk members. 320 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 343
    . This is usually an internal Fabric OS problem or file corruption. Recommended Action Reboot or power cycle the switch. If the message persists, run the firmwareDownload command to update the firmware. FABS-1004 Message process
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 344
    driver Recommended Action If the message is isolated, monitor the error messages on the switch. If the error is repetitive or if the fabric failed, failover or reboot the switch. If the message persists, run the firmwareDownload command to update the firmware. 322 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 345
    value in an object status field. This is usually an internal Fabric OS problem or file corruption. Recommended Action Reboot or power cycle the switch. If the message persists, run the firmwareDownload command to update the firmware. FABS-1008 Message : Media oid mapping failed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 346
    OS detected an unknown event type. This is usually an internal Fabric OS problem or file corruption. Recommended Action Reboot or power cycle the switch. If the message persists, run the firmwareDownload command to update the firmware. FABS-1011 Message []:Invalid
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 347
    FRU could not be enabled. This is usually an internal Fabric OS problem. Recommended Action Remove and reinsert the FRU. Reboot or power cycle the CP or system. If the message persists, run the firmwareDownload command to update the firmware. Fabric OS Message Reference 325 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 348
    command. Refer to the release notes to determine whether a non-disruptive firmware download is supported between the revisions. Because the AP and CP blades cannot communicate, it is not possible to load new firmware on the AP blade. If necessary, send the AP blade back to the factory for a firmware
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 349
    and failed to allocate new memory for an information unit (IU). Recommended Action A non-bladed switch will automatically reboot. For a bladed switch, the active CP blade will automatically fail over and the standby CP will become the active CP. Fabric OS Message Reference 327 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 350
    Wide Name (WWN) you are trying to add is present in some other login group, and therefore it will be removed from that login group and added to the new login group. Recommended Action Check the login group changes using the fcoelogincfg --show command. 328 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 351
    ERROR Probable Cause Indicates that removing a device from the login group has failed. Recommended Action Execute the supportSave command and restart the system. If the problem persists, contact your switch service provider. FCOE-1005 Message : membership check failed in logingroup:
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 352
    Severity ERROR Probable Cause Indicates that a request to delete ports from the specified VLAN has failed. Recommended Action Execute the supportSave command and restart the system. If the problem persists, contact your switch service provider. 330 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 353
    Severity ERROR Probable Cause Indicates that a request to add ports to the specified VLAN has failed. Recommended Action Execute the supportSave command and restart the system. If the problem persists, contact your switch service provider. FCOE-1015 Message Request to add MACs to Layer 2 for
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 354
    required. FCOE-1022 Message Max FCoE device login limit reached. Message Type LOG Severity WARNING Probable Cause Indicates that the switch has reached its maximum allowed FCoE device limit. Recommended Action Do not add any more FCoE devices to the switch. 332 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 355
    has not logged in. The end node must send a fabric login (FLOGI) before it can send an FDISC. Recommended Action It is due to a CNA or target driver issue. Contact CNA or target driver support team for assistance. FCOE-1025 Message FCoE logout received on FIP VN port. Message Type LOG Severity
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 356
    Cause Indicates that the FCoE device with the specified World Wide Name (WWN) is not a member of the login group. Recommended Action Change the FCoE login group policy on the switch using the fcoelogingroup command so that the device can log in. 334 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 357
    a version mismatch between the fabric login (FLOGI) and FDISC. Recommended Action It is due to a CNA or target driver issue. Contact CNA or target driver support team for assistance. FCOE-1030 Message Version mismatch between FIP LOGO and root VN port. Message Type LOG Severity WARNING
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 358
    FCoE priority or change the FCoE priority using the fabric-map default command under the FCoE configuration mode. FCOE-1037 Message Logingroup dropped for switch WWN: , due to name conflict while merging. Message Type LOG Severity WARNING Probable Cause Indicates that same login
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 359
    Indicates that the login group has been renamed. Recommended Action No action is required. FCOE-1041 Message Transaction aborted. Message Type LOG Severity INFO Probable Cause Indicates that the ongoing FCoE login configuration transaction is aborted. Fabric OS Message Reference 337 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 360
    No action is required. FCOE-1044 Message FCoE login configuration management enabled. Message Type LOG Severity INFO Probable Cause Indicates that the FCoE login configuration management is enabled. Recommended Action No action is required. 338 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 361
    creating a new file. Recommended Action No action is required. FCOE-1048 Message FCoE port is configured as VF port. Message Type LOG Severity INFO Probable Cause Indicates that the specified FCoE port is configured as a virtual fabric (VF) port. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 362
    5 FCOE-1048 Recommended Action No action is required. 340 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 363
    is possibly a private device which is not supported in this port type. Message Type LOG Severity INFO Probable Cause Indicates that device probing has failed because private devices will not respond to the switch port login (PLOGI) during probing. Fabric OS Message Reference 341 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 364
    5 FCPD-1003 Recommended Action The Brocade 4100, 4900, 5000, 7500, and AP 7600 do not support private loop devices. Refer to the switch vendor for a list of other port types that support private devices for inclusion into the fabric. 342 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 365
    WWN as old port as part of duplicate Port WWN detection policy. Message Type LOG Severity WARNING Probable Cause Indicates that the specified new port has the same Port World Wide Name (PWWN) as the old port. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 366
    busy login conditions, the buffer used for quick memory allocations (known as atomic malloc) can be quickly depleted and not replenished before the next allocation occurs. Recommended Action Reset the specified port using the portDisable and portEnable commands. 344 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 367
    proxy device in edge created at port . Message Type LOG Severity INFO Probable Cause Indicates that a proxy device at a port in the edge fabric has been imported at the specified port. Recommended Action No action is required. FCR-1002 Message FC router proxy device in edge
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 368
    -1006 Message FC router LSAN zone device added at port . Message Type LOG Severity INFO Probable Cause Indicates that a device is added to a logical storage area network (LSAN) zone in the edge fabric. Recommended Action No action is required. 346 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 369
    port was deleted in the edge fabric. Recommended Action No action is required. FCR-1008 Message FC router LSAN zone created at port
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 370
    1012 Message FC Router fabric build completed on port . Message Type LOG Severity INFO Probable Cause Indicates that the Fibre Channel router has completed a fabric build at the specified port. Recommended Action No action is required. 348 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 371
    Probable Cause Indicates that an EX_Port was created on the specified port in the specified domain. Recommended Action No action is required. FCR-1016 Message FCR fabric no longer reachable at port id (0x) fabric ID . Message Type LOG Severity INFO
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 372
    resources, LSAN device resources, and proxy device port resources. Use the fcrProxyDevshow command to view how many proxy devices are created in the fabric with the port resource problem. LSAN zones are removed using standard zoning commands such as zoneShow, zoneRemove, zoneDelete, cfgDelete, and
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 373
    WARNING Probable Cause Indicates that the number of port World Wide Names (WWNs) detected to be in use exceeds the local port WWN resources. Recommended Action Limit the number of port WWNs required by limiting the remote edge fabric connectivity (which limits the number of translate domains
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 374
    to EX_Port connectivity. WWN conflicts might cause unpredictable behavior in management applications. To avoid WWN conflicts, all EX_Ports attached to fabrics with highly dynamic changes to EX_Port connectivity should be disabled and then re-enabled. 352 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 375
    to EX_Port connectivity. WWN conflicts might cause unpredictable behavior in management applications. To avoid WWN conflicts, all EX_Ports attached to fabrics with highly dynamic changes to EX_Port connectivity should be disabled and then re-enabled. Fabric OS Message Reference 353 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 376
    Cause Indicates that the physical device World Wide Name (WWN) went offline in the specified fabric. Recommended Action No action is required. FCR-1032 Message Edge fabric enabled security on port in fabric . Message Type LOG Severity INFO Probable Cause Indicates
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 377
    . Message Type LOG Severity INFO Probable Cause Indicates that the specified logical storage area network (LSAN) zone was enabled in the backbone fabric. The enabled LSAN zone configuration is listed. Recommended Action No action is required. Fabric OS Message Reference 355 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 378
    fabric. Recommended Action No action is required. FCR-1038 Message Total zone entries exceeded local fabric alias entries created in a local fabric is greater than the local switch's zone database limitations. Recommended Action Remove excess cfg, zone, or alias the backbone fabric is greater
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 379
    within the backbone fabric was removed. Recommended Action No action is required. FCR-1043 Message Proxy device created in the backbone fabric. Message Type LOG Severity INFO Probable Cause Indicates that a proxy device was created in the backbone fabric. Fabric OS Message Reference 357 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 380
    the portEnable command. If the problem persists, reboot the switch. If the message persists, collect switch information using the supportSave command, and contact your switch service provider. FCR-1049 Message EX_Port () received an ELP command that is not supported. Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 381
    Indicates that a switch that does not support backbone-to-edge routing is running in the MetaSAN. Recommended Action No action is required if backbone-to-edge routing is not needed. Otherwise, replace the switch with one that supports backbone-to-edge routing. Fabric OS Message Reference 359 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 382
    domain ID of this port. Recommended Action Check the switches on both ends of the link for a possible mismatch in switch or port configuration parameters such as Operating Mode, E_D_TOV, R_A_TOV, Domain ID Offset, and so on. Run the portCfgExport command to modify the appropriate parameters
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 383
    Backbone fabric created on port . Message Type LOG Severity INFO Probable Cause Indicates that a backbone fabric was built on the specified port. Recommended Action No action is required. FCR-1062 Message Port disabled, system only supports EX
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 384
    does not match the local switch. Recommended Action Run the switchShow command to display the fabric ID. Change the fabric ID to match on both ends by modifying either the local or remote host using the fcrConfigure command. FCR-1064 Message Fabric ID of backbone FC-Routers mismatch or overlap
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 385
    . This is caused by issuing the fosConfig --disable fcr, configDefault, or the configDownload command with the fcrState set to 2 (disabled). Note that the FC Routing service is disabled by the factory. Recommended Action No action is required. Fabric OS Message Reference 363 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 386
    --enable fcr or the configDownload command with the fcrState set to 1 (enabled). Note that the FC Routing service is disabled by the factory. Recommended Action No action is required. FCR-1070 Message The FC Routing configuration is set to default. Message Type LOG Severity INFO Probable
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 387
    older firmware, which supports a lower number of logical storage area network (LSAN) zones. This is causing the loss of high availability (HA) sync. Recommended Action Keep the number of LSAN zones to the lower limit of the two CPs or upgrade the remote CP. Fabric OS Message Reference 365 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 388
    than characters in the edge fabric connected to port . Message Type LOG Severity ERROR Probable Cause Indicates that the zone name configuration size created in the connected fabric exceeds the maximum supported by the FC Router. This size is equal to the total
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 389
    switch in the fabric has not responded to the pause message which prevented the protocol from completing. Any data traffic disruption observed during the firmware download may have been the result of the rejected pause message. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 390
    a switch in the fabric has rejected the pause message which prevented the protocol from completing. Any data traffic disruption observed during the firmware download may have been the result of the rejected resume message. Recommended Action No action is required. 368 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 391
    HotCode protocol, a switch in the fabric did not accept the resume message which prevented the protocol from completing. Any data traffic disruption observed during the firmware download may have been the result of this issue. Recommended Action No action is required. FCR-1085 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 392
    Probable Cause Indicates that the EX_Port connects to the logical fabric containing a domain that has the capability to use extended ISL (XISL). Recommended Action Disable "Allow to use XISL" mode of the domain by using the configure command. FCR-1088 Message LSAN tag
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 393
    Action No action is required. FCR-1092 Message FCR ELS trap entries exhausted. Message Type LOG Severity ERROR Probable Cause Indicates that the FCR ELS trap entries are exhausted. Recommended Action Execute the supportSave command and contact your switch service provider. FCR-1093 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 394
    the Integrated Routing license is not installed. Recommended Action Install Integrated Routing license if device sharing is needed with other Brocade Native mode fabrics. FCR-1095 Message The EX-Port is configured in 'McData/Open' Mode which is no longer supported, hence will be
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 395
    and portEnable commands or the switchDisable and switchEnable commands. If the message persists, run the supportFtp command (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Fabric OS Message Reference 373 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 396
    FICON XRC Emulation License Key is not installed. Message Type LOG Severity WARNING Probable Cause Indicates FICON eXtended Remote Copy (XRC) Emulation requires a License Key. Recommended Action Use the appropriate License Key. FICN-1005 Message FICON GEPort TID
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 397
    GEPort TID FCIP tunnel to make the feature change effective. FICN-1007 Message DevDiskEgr:FICON Selective Reset recovery. Recommended Action If there was a job failure associated with this event, contact your vendor's customer support for assistance. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 398
    commands issued to the device> Sense Data:Bytes0-0xB=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 399
    a job or I/O failure associated with this event, contact your vendor's customer support for assistance. FICN-1013 Message DevDiskIng:Status=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 400
    LRC) values. This indicates data corruption between the emulation processing components. Recommended Action Contact your vendor's customer support for assistance. FICN-1016 ) frame to the FICON channel. Recommended Action No action is required. 378 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 401
    HostDomain HostPort DeviceDomain> LastCmd=0x LastStatus=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 402
    Severity ERROR Probable Cause Indicates the FICON channel issued a Selective Reset sequence for a device. Recommended Action If there was an unexpected job failure associated with this event, contact your vendor's customer support for assistance. 380 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 403
    the FICON channel issued a Purge Path command sequence for a device. Recommended Action If Reset sequence. Recommended Action If there was an unexpected job failure or I/O error associated with this event, contact your vendor's customer support for assistance. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 404
    Indicates an active disk emulation device received a Selective Reset from the FICON channel. Recommended Action If there was an unexpected job failure or I/O error associated with this event, contact your vendor's customer support for assistance. 382 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 405
    INFO Probable Cause Indicates the eXtended Remote Copy (XRC) System Data mover was restarted to discover the capabilities of the channel extension equipment. Recommended Action No action is required. This is a part of the XRC initialization. Fabric OS Message Reference 383 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 406
    Contact your vendor's customer support for assistance. FICN-1035 Message HostIng:FICON System Reset received on Path=0x< Reset to the specified FICON Control Unit. Recommended Action No action is required. This is a part of the FICON path initialization. 384 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 407
    Unit. Recommended Action No action is required. This is a part of the FICON path deactivation. FICN-1037 Message HostIng:FICON ELP Request on Path=0x with a FICON device. Recommended Action Contact your vendor's customer support for assistance. Fabric OS Message Reference 385 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 408
    1039 FICN-1039 Message HostIng:FCUB Lookup failed for HostDomain HostPort DeviceDomain> LastCmd=0x LastStatus=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 409
    Severity ERROR Probable Cause Indicates that protocol errors in emulation in the Control Unit or network errors can cause a Selective Reset. Recommended Action If this was an unexpected event, contact your vendor's customer support for assistance. Fabric OS Message Reference 387 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 410
    4 commands received from the channel for this device> lastStatus=0x treating as system reset event. This is an unexpected event; contact your vendor's customer support for assistance. 388 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 411
    DevicePort LPAR CUADDR DeviceAddr>** Index=. Message Type LOG Severity is an unexpected event; contact your vendor's customer support for assistance. Fabric OS Message Reference 389 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 412
    a PSF command has been received to withdraw from the eXtended Remote Copy (XRC) session with the extended direct attached storage device (DASD) device. Recommended Action If this was an unexpected event, contact your vendor's customer support for assistance. 390 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 413
    Probable Cause Indicates a PSF command has been received to suspend all extended direct attached storage device (DASD) devices from the eXtended Remote Copy (XRC) session. Recommended Action If this was an unexpected event, contact your vendor's customer support for assistance. FICN-1056
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 414
    Indicates an internal resource shortage caused an error so that an emulation frame could not be created and sent to an Logical Partition (LPAR). Recommended Action This is an unexpected event; contact your vendor's customer support for assistance. 392 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 415
    created and sent to a device. Recommended Action This is an unexpected event; contact your vendor's customer support FC interface for an active emulation exchange. Recommended Action This is an unexpected event; contact your vendor's customer support for assistance. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 416
    Source Domain> to DID=0x. Message Type FC interface for an exchange. Recommended Action If there were associated I/O errors at the same time as this event, contact your vendor's customer support for assistance. 394 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 417
    GE1 number> could not create required structure. Message Type LOG FC interface for an emulation Control Unit exchange. Recommended Action If there were associated I/O errors at the same time as this event, contact your vendor's customer support for assistance. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 418
    configuration. Refer to the string for the nature of the configuration issue. Recommended Action If resolution of the configuration issue cannot be completed, contact your vendor's customer support . Recommended Action The end of tape is a required. 396 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 419
    device. Recommended Action No action is required. FICN-1073 Message HostTapeIngr:Unloaded:Path= number of emulated host write commands processed while this tape was loaded>:Chains=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 420
    loaded>:Cmds=0x:Chains=0x: the currently loaded tape. Recommended Action No action is required. 398 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 421
    loaded>:Cmds=0x:Chains=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 422
    host read commands processed while this tape was loaded>:Chains=0x:Chains=0x treating as system reset event. Message Type LOG
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 423
    customer support for assistance. FICN-1082 Message EmulEls:CSWR_RSCN received on GEPort= VEPort= Domain=0x Port=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 424
    ge0 or ge1>,tunnel Id=. Message Type LOG Severity ERROR Probable Cause Indicates a FICON FCIP tunnel to the peer switch has been terminated. Recommended Action This is an unexpected event; contact your vendor's customer support for assistance. FICN-1087 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 425
    Cause Indicates the FICON channel issued a Selective Reset for a device that was active in emulation. Recommended Action If there was an unexpected job failure associated with this event, contact your vendor's customer support for assistance. Fabric OS Message Reference 403 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 426
    issued a Selective Reset sequence for a device a Purge Path command sequence for a data from a FICON device. Recommended Action If there was an unexpected job failure or I/O error associated with this event, contact your vendor's customer support for assistance. 404 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 427
    Ending completing an emulated Selective Reset sequence. Recommended Action Command Reject Sense from the device. Recommended Action If there was an unexpected job failure or I/O error associated with this event, contact your vendor's customer support for assistance. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 428
    HostPort DeviceDomain> LastCmd=0x LastStatus=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 429
    4 commands received from the channel for this device> lastStatus=0x treating as system reset event. is normally an unexpected event; contact your vendor's customer support for assistance. Fabric OS Message Reference 407 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 430
    No action is required. FICN-1105 Message DeviceAddr> lastCmds=0x treating as system reset event. Message Type LOG Severity WARNING Probable Cause support for assistance. 408 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 431
    HostDomain HostPort DeviceDomain> LastCmd=0x LastStatus=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 432
    the FICON channel issued a Selective Reset sequence for a device. Recommended command sequence for a device. Recommended Action If there was an unexpected job failure or I/O error associated with this event, contact your vendor's customer support for assistance. 410 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 433
    LPAR CUADDR DeviceAddr> lastCmds=0x to the channel for this device> treating as system reset event. Message Type LOG Severity WARNING Probable Cause Indicates support for assistance. Fabric OS Message Reference 411 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 434
    0x LastCmd=0x LastStatus=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 435
    Probable Cause Indicates a Purge Path was received from the locally connected FICON channel. This is performed during FICON path recovery. Recommended Action If this was an unexpected event, contact your vendor's customer support for assistance. Fabric OS Message Reference 413 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 436
    treating as system reset event. Message Type LOG 's customer support for assistance. FICN-2005 Message FICON VEPort configuration was changed manually. Recommended Action No action is required. 414 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 437
    Disable the applicable FCIP tunnel to make Port> to DID=0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 438
    VEport= could not create required structure. Message Type LOG port with the established FICON emulated path has logged out from the switch. Recommended Action This may be an unexpected event; contact your vendor's customer support for assistance. 416 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 439
    FCP) emulation-enabled FCIP tunnel to the peer switch has been terminated. Recommended Action This is an unexpected event; contact your vendor's customer support for assistance. FICN- tunnel compression mode to None (mode 0) or Aggressive (mode 3). Fabric OS Message Reference 417 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 440
    the installed licenses on the switch. The switch cannot be managed using FICON-CUP commands until the FICON-CUP license is installed. Contact your switch supplier for a FICON-CUP license. Execute the licenseAdd command to add the license to your switch. 418 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 441
    enable FMS mode, the core PID format must be used in the fabric. Change the PID format to core PID using the configure command and re-enable FMS Mode using the ficonCupSet command. Refer to the Fabric OS Administrator's Guide for information on core PID mode. FICU-1005 Message Failed to initialize
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 442
    filtering resources required to enable FICON Management Server mode (fmsMode) were not available on some of the ports. Recommended Action Execute the haFailover command on the switch if it has redundant control processors (CPs) or reboot the switch. 420 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 443
    No action is required. FICU-1012 Message FMS mode has been disabled. Message Type AUDIT | LOG Class CFG Severity INFO Probable Cause Indicates that the FICON Management Server mode (fmsMode) has been disabled. Recommended Action No action is required. Fabric OS Message Reference 421 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 444
    FICU-1013 FICU-1013 Message Host data file cannot be reset to proper size. Message Type LOG Severity WARNING Probable Cause Indicates that the file system is too full to create the host data file at the proper size. Recommended Action Execute the switchStatusShow command to check if the flash
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 445
    FICU-1021 Message Port Addrs () have been Unblocked by . Message Type AUDIT | LOG Class CFG Severity INFO Probable Cause Indicates the FICON Management Server (FMS) has unblocked ports. Recommended Action No action is required. Fabric OS Message Reference 423 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 446
    the presence of unmanageable ports such as 48-port blade ports in the virtual fabric-disabled chassis. Recommended Action No action is required. For more information on the FICON CUP restrictions, refer to the FICON Administrator's Guide. FICU-1023 Message Detected 48 port blade when FMS mode
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 447
    is still active. When the FC kernel driver reuses the exchange, the application will overlap. This happens on a timed-out exchange; it automatically recovers after the application times out the exchange. Recommended Action No action is required. Fabric OS Message Reference 425 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 448
    state record (LSR). Recommended Action No action is required; the record is discarded. FLOD-1004 Message support. Recommended Action Reduce the number of switches in the fabric or reduce the number of redundant inter-switch links (ISLs) between two switches. 426 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 449
    (LSR) contained an invalid domain number. Recommended Action No action is required; the LSR is discarded. FLOD-1006 Message Transmitting invalid domain ID: invalid domain number. Recommended Action No action is required; the LSR is discarded. Fabric OS Message Reference 427 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 450
    of range because it does not exist on the switch. Recommended Action No action is required. This is a temporary kernel error that does not affect your system. If the problem persists, execute the supportSave command and contact your service provider. FSPF-1002 Message Wrong neighbor ID (
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 451
    in a fabric of Brocade switches. Disconnect the incompatible switch. FSPF-1006 Message FSPF Version not supported, input port = . Message domains using ICL or regular inter-switch link (ISL) to form a triangular topology. Fabric OS Message Reference 429 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 452
    the local switch. Recommended Action No action is required. FSPF-1011 Message 16G ICL topology is unbalanced. Message Type LOG Severity WARNING Probable Cause Indicates that the current configuration of inter-chassis link (ICL) paths are unbalanced. 430 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 453
    have been corrected. Message Type LOG Severity INFO Probable Cause Indicates that the existing inter-chassis link (ICL) configuration that was resulting in an unbalanced topology has been corrected. Recommended Action No action is required. Fabric OS Message Reference 431 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 454
    For non-bladed systems, restart the switch using the reboot command. If the problem persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 432 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 455
    that data is not available on the Fabric OS state synchronization (FSS) device. Recommended Action If the problem persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 456
    configuration and then execute the haSyncStart command to restore the high availability (HA) synchronization. If the problem persists, contact your switch service provider. FSS-1008 Message FSS Error: . Message Type LOG Severity CRITICAL Probable Cause Indicates that a Fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 457
    command and contact your switch service provider. FSS-1011 Message FSS Info: . Message Type LOG Severity INFO Probable Cause Indicates a Fabric OS state synchronization (FSS) related informational message. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 458
    will be disruptive. In a switch system, this message is logged when a firmware upgrade or downgrade was invoked. The new firmware version is not compatible with the current running version. This causes a disruptive firmware upgrade or downgrade. 436 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 459
    FSSM-1004 5 Recommended Action For a dual CP system, execute the firmwareDownload command to load compatible firmware on the standby CP. Fabric OS Message Reference 437 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 460
    policy of the end-user installation. Typically, low temperatures mean that the fans and airflow of a switch are functioning normally. Verify that the location temperature is within the operational range of the switch. Refer to the hardware reference manual for the environmental temperature
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 461
    that the speed of the fan has changed. Fan problems typically contribute to temperature problems. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Consistently abnormal fan speeds generally indicate that the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 462
    . If the power supply is functioning below the acceptable boundary, verify that it is seated correctly in the chassis. Run the psShow command to view the status of the power supply. If the power supply continues to be a problem, replace the faulty power supply. 440 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 463
    that the power supply counter changed from a value outside of the acceptable range to a value within the acceptable range. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 441
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 464
    boundary. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1035 Message , is may indicate a deteriorating SFP. Recommended Replace the SFP. Action 442 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 465
    SFP. Recommended Action No action is required. FW-1037 Message , value LOG Severity INFO Probable Cause Indicates that the receive power value of the small form-factor pluggable (SFP Replace deteriorating cables or SFPs. Check for damage from heat or age. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 466
    Type LOG Severity INFO Probable Cause Indicates that the receive power value of the small form-factor pluggable (SFP) has is required. Respond to this message as is appropriate to the particular policy of the end-user installation. replace the SFP. 444 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 467
    Probable Cause Indicates that the transmit power value of the small form- threshold, the SFP is deteriorating. Recommended Replace the SFP. Action FW-1044 Message required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 468
    . If the supplied voltage of the SFP transceiver is outside of the normal range, this may indicate a hardware failure. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. If the message persists, replace the SFP
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 469
    required. Respond to this message as is appropriate to the particular policy of the end-user installation indicate that the SFP is deteriorating. Recommended Replace the SFP. Action FW-1050 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 470
    Power on Hours has fallen below the low boundary. Recommended Action Configure the low threshold to 1 so that the threshold triggers an alarm when the value falls to 0 (Out_of_Range). If continuous or repeated alarms occur, replace the SFP before it deteriorates. 448 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 471
    (SFP) Power on Hours has risen the SFP. Recommended Replace the SFP. Action required. Respond to this message as is appropriate to the particular policy of the end-user installation. A low number of E_Port failures means that the switch is functioning normally. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 472
    to go down. Down E_Port may be caused by transient errors. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1117 Message , value has changed(High=, Low=). Current value is
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 473
    that all inter-switch link (ISL) cables are properly connected at both ends. Verify that the small form-factor pluggable (SFP) has not become faulty. An inexplicable fabric reconfiguration might be a transient error and might not require troubleshooting. Fabric OS Message Reference 451 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 474
    is a conflict of domain IDs in a single fabric and the principal switch must assign another domain ID to the switch. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1122 Message , is below low
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 475
    fabric and the principal switch has to assign another domain ID to the switch. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation link between two switches. Fabric OS Message Reference 453 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 476
    E_Port initialization, ports exchange link parameters. Rarely, incompatible parameters result in segmentation. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 454 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 477
    configuration. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation zone configuration. A low number of zone configuration changes means that the fabric is functioning normally. Fabric OS Message Reference 455
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 478
    changed. Fabric logins occur when a port or device initializes with the fabric. The event is called fabric login (FLOGI). Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 456 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 479
    range. Fabric logins occur when a port or device initializes with the fabric. The event is called fabric login (FLOGI). Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 457 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 480
    state changes has risen above the high boundary. SFP state changes occur when the SFP is inserted or removed. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 458 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 481
    that the switch is functioning normally. Recommended Action Check for concurrent loss of synchronization errors and, if applicable, troubleshoot them. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 459 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 482
    Recommended Action Check for concurrent loss of synchronization errors and, if applicable, troubleshoot them. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1164 Message , value has changed(High=, Low=
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 483
    Recommended Action Check both ends of your cable connection. Verify that the cable and SFPs are not faulty. If you continue to experience loss of synchronization errors, troubleshoot your host bus adapter (HBA) and contact your switch service provider. Fabric OS Message Reference 461 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 484
    indicates a physical problem. A low number of signal loss errors means that the switch is functioning normally. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 462 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 485
    protocol errors occur due to software glitches. Persistent protocol errors occur due to hardware problems. Recommended Action Check both ends of your cable connection. Verify that the cable and small form-factor pluggables (SFPs) are not faulty. Fabric OS Message Reference 463 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 486
    protocol errors occur due to software glitches. Persistent protocol errors occur due to hardware problems. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 464 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 487
    that the port experiences has risen above the high boundary. Invalid words usually indicate a hardware problem with a small form-factor pluggable (SFP) or cable. Recommended Action Verify that both ends of the connections, the SFP, and the cable are not faulty. Fabric OS Message Reference 465
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 488
    range. Invalid words usually indicate a hardware problem with a small form-factor pluggable (SFP) or cable. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1180 Message , value has
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 489
    INFO Probable Cause Indicates that the percentage of incoming traffic that the port experiences has changed. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 467 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 490
    the port experiences has changed from a value outside of the acceptable range to a value within the acceptable range. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 468 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 491
    action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1190 Message < is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 469 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 492
    or has become a trunk port. A low number of port state changes means that the switch is functioning normally. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 470 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 493
    of link resets that the port experiences has changed. Link resets occur due to link timeout errors that indicate no frame activity. Recommended Action Check both ends of your cable connection. Verify if the cable and small form-factor pluggables (SFPs) are faulty. Fabric OS Message Reference 471
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 494
    link resets that the port experiences has fallen below the low boundary level. Link resets occur hardware problems can cause link resets to increase. Recommended Action Respond to this message as is appropriate to the particular policy of the end-user installation. 472 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 495
    Action Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1202 Message , is above high boundary(High=, Low=
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 496
    thresholds. Recommended Action Check the target device; it could be slow. FW-1204 Message value has changed(High=, Low=). Current value is boundary threshold. Recommended Action No action is required. 474 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 497
    1207 Message is required. in the FC frame. problem in this area. Recommended Action Verify that your optical components are clean and function properly. Replace deteriorating cables or small form-factor pluggables (SFPs). Check for damage from heat or age. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 498
    large numbers of messages indicate a problem in this area. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. A low level of invalid CRC errors means that the switch is functioning normally. FW-1218 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 499
    that errors have been detected in the FC frame. Invalid CRC messages occur when the problem in this area. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation Fabric OS Message Reference 477 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 500
    change. These messages might also be caused by dirty equipment, temperature fluctuations, and aging equipment. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 478 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 501
    messages appear due to the number of word frames that travel from the configured S_ID to the D_ID pair. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 479 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 502
    that the number of end-to-end word frames that the switch receives has changed from configured S_ID to the D_ID pair. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 480 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 503
    System Interface (SCSI) Read, SCSI Write, SCSI Read and Write, SCSI Traffic, or IP commands in a frame. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 481 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 504
    System Interface (SCSI) Read, SCSI Write, SCSI Read and Write, SCSI Traffic, or IP commands in a frame. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 482 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 505
    request has been received from an unauthorized IP address. The TELNET_POLICY contains a list of IP addresses that are authorized to establish Telnet connections to switches in the fabric. Recommended Action Execute the errShow command to determine the IP address that sent the request. Responses to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 506
    connection request has been received from an unauthorized IP address. The HTTP_POLICY contains a list of IP addresses that are authorized to establish browser connections to the switches in the fabric. Recommended Action No action is required. 484 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 507
    that an API connection request has been received from an unauthorized IP address. The Simple Network Management Protocol policy (SNMP_POLICY) contains a list of IP addresses that are authorized to establish API connections to switches in the fabric. Fabric OS Message Reference 485 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 508
    received from an unauthorized IP address. The Simple Network Management Protocol policy (SNMP_POLICY) contains a list of IP addresses that are authorized to establish API connections to switches in the fabric. Recommended Action Execute the errShow command to determine the IP address that sent the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 509
    has been received from an unauthorized IP address. The Simple Network Management Protocol policy (SNMP_POLICY) contains a list of IP addresses that are authorized to establish API connections to switches in the fabric. Recommended Action No action is required. FW-1308 Message , value has
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 510
    unauthorized IP address. Recommended Action Execute the errShow command to determine the IP address received from an unauthorized IP address. Recommended Action No action is required. FW-1312 Message < IP address. Recommended Action Execute the errShow command to determine the IP address
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 511
    has been received from an unauthorized IP address. Recommended Action Execute the errShow command to determine the IP address that sent the request. Responses been received from an unauthorized IP address. Recommended Action No action is required. Fabric OS Message Reference 489 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 512
    has been received from an unauthorized World Wide Name (WWN). The SES_POLICY contains a list of WWNs of device ports that are allowed to access the SES Server functionality. Recommended Action Execute the errShow command to determine the IP address that sent the request. Responses to security
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 513
    that an MS access request has been received from an unauthorized World Wide Name (WWN). The MS_POLICY contains a list of WWNs of device ports that are allowed to access the Management Server functionality. Recommended Action No action is required. Fabric OS Message Reference 491 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 514
    has been received from an unauthorized World Wide Name (WWN). The MS_POLICY contains a list of WWNs of device ports that are allowed to access the Management Server functionality. Recommended Action Execute the errShow command to determine the WWN of the device that sent the request. Responses to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 515
    range. Serial violations indicate that an unauthorized serial port request has been received. The SERIAL_POLICY contains a list of switch World Wide Names (WWNs) for which serial port access is enabled. Recommended Action No action is required. Fabric OS Message Reference 493 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 516
    panel violations indicate that an unauthorized front panel request has been received. The FRONTPANEL_POLICY contains a list of switch World Wide Names (WWNs) for which front panel access is enabled. Recommended Action Execute the errShow command to determine the WWN of the device that sent the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 517
    the low boundary. SCC violations indicate that an unauthorized switch tried to join the fabric. The SCC_POLICY contains a list of switches by World Wide Name (WWN) that are allowed to be members of a fabric. Recommended Action No action is required. Fabric OS Message Reference 495 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 518
    . SCC violations indicate that an unauthorized switch tried to join the fabric. The SCC_POLICY contains a list of switches by World Wide Name (WWN) that are allowed to be members of a fabric. Recommended Action Execute the errShow command to determine the WWN of the device that sent the request
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 519
    server. Recommended Action Execute the errShow command to determine the device WWN, switch WWN, and switch port. Responses to security-class messages depend on user policies. Consult your security administrator for response strategies and policies. Fabric OS Message Reference 497 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 520
    a device performs a fabric login (FLOGI) request, the World Wide Name (WWN) specified in the FLOGI is validated to be connected to the authorized port. Enforcement for private loop devices not performing FLOGI is done through the name server. Recommended Action No action is required. FW-1340
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 521
    an invalid timestamp has been received from the primary fabric configuration server (FCS). When the primary FCS downloads a new configuration to other switches in the fabric, the packet is tagged with a timestamp. The receiving switch compares this timestamp to its current time. If the difference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 522
    fabric configuration server (FCS). When the primary FCS downloads a new configuration to other switches in the fabric, the packet is tagged with a timestamp. The receiving switch compares security administrator for response strategies and policies. 500 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 523
    fabric configuration server (FCS). When the primary FCS downloads a new configuration to other switches in the fabric, the packet is tagged with a timestamp. The receiving switch compares security administrator for response strategies and policies. Fabric OS Message Reference 501 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 524
    signature has been received from the primary fabric configuration server (FCS). When the primary FCS downloads a new configuration to the other switches in the fabric, the packet is signed using the private key of the primary FCS. The receiving switch must verify this signature with the public
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 525
    configuration server (FCS). Before a new primary FCS switch sends any configuration data to any switch in the fabric, it first sends its certificate to all the switches in the fabric. The receiving switch must verify that the sender is the primary FCS switch and its certificate is signed by the Root
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 526
    configuration server (FCS). Before a new primary FCS switch sends any configuration data to any switch in the fabric, it first sends its certificate to all the switches in the fabric. The receiving switch must verify that the sender is the primary FCS switch and its certificate is signed by the Root
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 527
    ). Before a new primary FCS switch sends any configuration data to any switch in the fabric, it first sends its certificate to all the switches in the fabric. The receiving switch has to verify that the sender is the primary FCS switch and its certificate is signed by the Root CA recognized by the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 528
    LOG Severity INFO Probable Cause Indicates that the number of Switch Link Authentication Protocol (SLAP) faulty packets has changed. This counter keeps track of the number of unexpected SLAP packets and SLAP packets with faulty transmission IDs. 506 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 529
    > . Message Type LOG Severity INFO Probable Cause Indicates that the number of switch link authentication protocol (SLAP) faulty packets has fallen below the low boundary. This counter IDs. Recommended Action No action is required. Fabric OS Message Reference 507 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 530
    that the number of time service (TS) out-of-sync violations has risen above the high boundary. Recommended Action Responses to security-class messages depend on user policies. Consult your security administrator for response strategies and policies. 508 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 531
    World Wide Name (WWN) of that primary FCS switch. If a secure switch finds that there are no FCSs in the fabric, but it still has the WWN of the last primary FCS switch, it increments this counter and resets the WWN of the primary FCS to all zeroes. Fabric OS Message Reference 509 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 532
    primary FCS switch. If a secure switch finds that there are no FCSs in the fabric, but it still has the WWN of the last primary FCS switch, it increments this counter and resets the WWN of the primary FCS to all zeroes. Recommended Action No action is required. 510 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 533
    detected. When a switch is in secure mode, it connects only to another switch that is in secure mode and has a compatible security database. A compatible security database means that the version stamp and fabric configuration server (FCS) policy matches exactly. Fabric OS Message Reference 511 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 534
    , it connects only to another switch that is in secure mode and has a compatible security database. A compatible security database means that the version stamp and fabric configuration server (FCS) policy matches exactly. Recommended Action No action is required. FW-1376 Message , value
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 535
    . This counter tracks how many times commands allowed only on the primary fabric configuration server (FCS) switch have been executed on a non-primary FCS switch. There are many commands that can be executed only on the primary FCS switch, as well as one security command that can be executed only on
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 536
    below the low boundary. Flash memory increases and decreases slightly with normal operation of the switch. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 514 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 537
    switch. Recommended Action Remove some unwanted files to create some flash space. Execute the supportSave command action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1404 required. Fabric OS Message Reference 515 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 538
    that the memory usage is above the high memory threshold. Recommended Action No action is required. FW-1407 Message , is between high and low boundaries(High=, memory thresholds. Recommended Action No action is required. 516 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 539
    Indicates that the switch status has changed to a healthy state. This occurred because a policy is no longer violated. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 517 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 540
    Indicates that the switch is not in a healthy state. This occurred because the number of missing power supplies is greater than or equal to the policy set by the switchStatusPolicySet command. Recommended Action Replace the missing power supply. 518 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 541
    is greater than or equal to the policy set by the switchStatusPolicySet command. A fan is faulty when the value is not in the acceptable range or is faulty. Recommended Action Replace the faulty or deteriorating fan field-replaceable units (FRUs). Fabric OS Message Reference 519 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 542
    if both the CPs have compatible firmware levels. Execute the firmwareDownload command to install the same level of firmware to both CPs. Replace any faulty CPs. If you reset the micro-switch (the latch on the CP blade) on the active CP before the heartbeat was up on a power cycle, and the CPs came
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 543
    than or equal to the policy set by the switchStatusPolicySet command. A port is considered faulty due to hardware failure such as a faulty small form-factor pluggable (SFP) or port. Recommended Action Replace any faulty or deteriorating SFPs. Fabric OS Message Reference 521 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 544
    missing SFPs> missing SFPs out of SFPs:config( percent,). (Port(s) ). Message Type LOG Severity WARNING Probable Cause Indicates that the switch is not in a healthy state. This occurred because the number of missing
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 545
    the state of the specified field-replaceable unit (FRU) has changed to inserted. This means that a FRU is inserted but not powered on. Recommended Action Verify that the the state of the specified field-replaceable unit (FRU) has changed to faulty. Fabric OS Message Reference 523 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 546
    service) indicating switch status is marginal. Recommended Action To maintain full (2X) redundancy and proper monitoring by Fabric Watch, supply four active power supplies and enter the default values associated with the presence of an AP blade using the switchStatusPolicySet command. 524 Fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 547
    command. Recommended Action Replace the faulty core blade. FW-1448 Message Switch status change contributing factor Error ports: Error out of ports:config( percent,). (Port(s)
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 548
    is required. FW-1502 Message Invalid Email address is configured from hardware problems. Recommended Action Check for concurrent loss of synchronization errors. Check the SFP and the cable. Then, enable the port using the portEnable command. 526 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 549
    for concurrent loss of synchronization errors and, if applicable, troubleshoot them. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1512 Message , has dropped below upper threshold
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 550
    pluggable (SFP) or cable. Signal losses often create synchronization losses. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1515 Message , has crossed lower threshold boundary
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 551
    range. Invalid words usually indicate a hardware problem with a small form-factor pluggable (SFP) or cable. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 529 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 552
    range. Invalid words usually indicate a hardware problem with a small form-factor pluggable (SFP) or cable. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1521 Message , has crossed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 553
    that the port experiences has changed and crossed the lower threshold boundary to a value within the acceptable range. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. Fabric OS Message Reference 531 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 554
    is testing, is faulty, has become an E_Port, has become an F_Port, has segmented, or has become a trunk port. Recommended Action No action is required. Respond to this message as is appropriate to the particular policy of the end-user installation. 532 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 555
    and hardware problems can cause link resets to increase. Recommended Action Respond to this message as is appropriate to the particular policy of the end-user installation. FW-1530 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 556
    thresholds. Recommended Action Check the target device; it could be slow. FW-1533 Message has crossed lower threshold boundary to in between(High=, Low=
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 557
    Cause Indicates that Port Fencing is configured for link loss and synchronization loss in previous versions, but upgrading to a new version resets the bit because Port Fencing is not supported. Recommended Action No action is required. You are informed that the Port Fencing bit is reset. FW-2000
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 558
    Respond to this message as is appropriate to the particular policy of the end-user installation. FW-3011 Message is below low boundary(High=, Low=< high boundary threshold. Recommended Action No action is required. 536 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 559
    Respond to this message as is appropriate to the particular policy of the end-user installation. FW-3015 Message is below low boundary(High=, Low=
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 560
    experiences is above the high boundary threshold. Recommended Action No action is required. FW-3017 Message is between high and low boundaries(High=, to the particular policy of the end-user installation. 538 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 561
    has gone offline or the circuit has come online. Recommended Action No action is required. FW-3020 Message is above high boundary(High=, Low=). is testing. Recommended Action No action is required. Fabric OS Message Reference 539 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 562
    Minute as Seconds is not supported. Message Type LOG Severity INFO Probable Cause Indicates that the timebase for the class is changed implicitly to minutes because a seconds timebase is not supported. Recommended Action No action is required. 540 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 563
    , haFailover, and reboot commands. Some examples of errors that may initiate this message are hardware errors, software errors, compact flash errors, or memory errors. The Reboot Reason variable can be one of the following: • Hafailover • Reset Fabric OS Message Reference 541 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 564
    HAM • EMFault:EM Recommended Action Execute the errShow command on both control processors (CPs) to view that may indicate reason for the switch restart. HAM-1005 Message HeartBeat reset it if it is down. Recommended Action No action is required. 542 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 565
    test run by the high availability manager (HAM) module. Recommended Action The standby CP will take over and reset the active CP. The system switch will automatically restart. Otherwise, execute the reboot command to manually restart the switch. HAM-1008 Message Rebooting the system for recovery
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 566
    out of memory (OOM) condition has been detected when switch was ready for warm recovery. The haReboot is automatically triggered. Recommended Action No action is required. The haReboot is automatically triggered to recover from the OOM condition. 544 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 567
    . Recommended Action Manually initiate a restart command. HAM-1015 Message . Message Type AUDIT Class RAS Severity INFO Probable Cause Indicates that a terminated software component has been restarted. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 568
    your switch service provider. HAMK-1002 Message Heartbeat down. Message Type LOG Severity INFO Probable Cause Indicates that the active control processor (CP) blade determined that the standby CP blade is down. This can be a result of a user-initiated action such as firmware download, the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 569
    is displayed when the standby CP has been restarted. Note that in certain circumstances, a CP may experience a double reset and restart twice. A CP can recover automatically even if it has restarted twice. Recommended Action No action is required. Fabric OS Message Reference 547 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 570
    Run the psShow command to verify the power supply status. Try to reseat the faulty fan field-replaceable units (FRUs) and power supply FRU to verify that they are seated properly. If the problem persists, replace the fan FRU or the power supply FRU as necessary. 548 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 571
    the psShow command to verify the power supply status. Try to reseat the faulty fan field-replaceable units (FRUs) and power supply FRU to verify that they are seated properly. If the problem persists, replace the fan FRU or the power supply FRU as necessary. HIL-1105 Message Switch error,
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 572
    your switch. Refer to the hardware reference manual for your switch for the operational temperature range. Run the fanShow command to monitor the speed of the fan generating this error. If the fan continues to generate this message, replace the fan FRU. 550 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 573
    to the hardware reference manual for your switch for the operational temperature range. Run the fanShow command to monitor the speed of the fan generating this error. If the fan continues to generate this message, replace the fan FRU. HIL-1204 Message Fan faulted, speed (
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 574
    to the hardware reference manual for your switch for the operational temperature range. Use the fanShow command to monitor the status of the fan generating this error. If the fan continues to generate this message, replace the switch because the fan is not field-replaceable. HIL-1208 Message Fan
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 575
    is often preceded by a low speed error message. This problem can cause the switch to overheat. Recommended Action Replace the affected fan FRU immediately. HIL-1302 Message blowers failed or missing. Replace failed or missing blower assemblies immediately. Message Type LOG Severity
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 576
    . Message Type LOG Severity ERROR Probable Cause Indicates that three fan field-replaceable units (FRUs) have failed. This message is often preceded by a low fan speed message. Recommended Action Replace the faulty fan FRUs immediately. 554 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 577
    the faulty fan field-replaceable units (FRUs) immediately. HIL-1310 Message fan(s) faulty. Message Type LOG Severity WARNING Probable Cause Indicates that multiple fans have failed. This message is often preceded by a low fan speed message. Fabric OS Message Reference 555 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 578
    Message Two fan FRUs missing. Install fan FRUs immediately. Message Type LOG Severity WARNING Probable Cause Indicates that two fan field-replaceable units (FRUs) have been removed. Recommended Action Install the missing fan FRUs immediately. 556 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 579
    Run the fanShow command to verify all the fans are working properly. Make sure that the area is well-ventilated and that the room temperature is within operational range of your switch. Refer to the hardware reference manual for your switch for the operational temperature range. Fabric OS Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 580
    command to verify all the fans are working properly. Make sure that the area is well-ventilated and that the room temperature is within the operational range of your switch. Refer to the hardware reference manual for your switch for the operational temperature range. If the message persists, replace
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 581
    prevent future problems, make sure that all the fans are working properly. Make sure that the area is well-ventilated and that the room temperature is within the operational range of your switch. Refer to the hardware reference manual for your switch for the operational temperature range. Fabric OS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 582
    future problems, make sure that all the fans are working properly. Make sure that the area is well-ventilated and that the room temperature is within the operational range of your switch. Refer to the hardware reference manual for your switch for the operational temperature range. 560 Fabric OS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 583
    that all fans are operating correctly. Replace any deteriorating fan field-replaceable units (FRUs). Run the tempShow command to verify temperature values. If any sensor is too high, monitor the switch. Try rebooting or power cycling the switch. Fabric OS Message Reference 561 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 584
    only to the Brocade 5100. Recommended Action Ensure the power cord is connected to the unit with a valid power source and then switch on the unit. If the problem persists, try reseating the unit. If the problem still persists, replace the FRU. 562 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 585
    is applicable only to the Brocade 6510. Recommended Action Use the chassisShow command to check the airflow directions of the power supply and fan assemblies. Ensure that the airflows run in the same direction. HIL-1612 Message MISMATCH in PSU-FAN Air Flow direction. System shut down. Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 586
    to WWN halted. Message Type LOG Severity ERROR Probable Cause Indicates that one or both of the World Wide Name (WWN) cards is missing. Both WWN cards must be present for normal operation. Recommended Action Make sure both WWN cards are inserted. 564 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 587
    In Fabric OS, the HLO timeout value is not configurable, so this error can only occur when the Brocade switch is connected to a switch from another manufacturer. Recommended Action The HLO timeout value of the remote switch must be compatible with the value specified in the FSPF protocol. Refer to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 588
    when the Brocade switch is connected to a switch from another manufacturer. Recommended Action The HLO message of the remote switch must be compatible with the value specified in the FSPF protocol. Refer to the documentation for the other manufacturer's switch to change this value. 566 Fabric OS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 589
    Execute the firmwareDownload command to reinstall the firmware to your switch. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 567 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 590
    Indicates a hardware subsystem layer (HSL) initialization failure. This error is caused by other system errors. Recommended Action Execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. HSL
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 591
    Recommended Action No action is required. HSL-1004 Message Incompatible the shutdown command and insert an SFP transceiver that is supported on the Fabric OS State Synchronization (FSS) service. This error is caused by other system errors. Recommended Action Execute the errShow command
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 592
    kernel memory. Recommended Action Install more memory on the command and re-insert the SFP transceiver. After the SFP transceiver is inserted, re-enable the interface using the no shutdown command. If the problem persists, contact your switch service provider. 570 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 593
    the port ID (PID) format was changed. Recommended Action No action is required. For more information on PID format, refer to the Fabric OS Administrator's Guide. HTTP message log by using the errShow command, and take appropriate corrective actions. Fabric OS Message Reference 571 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 594
    Disabling port. Message Type LOG Severity ERROR Probable Cause Indicates that the specified port has crashed unexpectedly and restarting attempts have failed. Recommended Action Power cycle the blade using the slotPowerOff and slotPowerOn commands. 572 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 595
    Indicates that the local IP address has been changed manually or it was reconfigured automatically by the Dynamic Host Configuration Protocol (DHCP) server. Recommended Action No action is required. IPAD-1001 Message /
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 596
    Severity INFO Probable Cause Indicates that the Domain Name System (DNS) parameters are saved successfully. Recommended Action No action is required. IPAD-1004 Message DNS parameters removed successfully. Message Type LOG Severity INFO Probable Cause Indicates that the Domain Name System
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 597
    commands to add the license to your switch and activate it. IPS-1002 Message Failed to initialize rc = . Message Type LOG Severity ERROR Probable Cause Indicates that the initialization of a module within the IPS daemon failed. Recommended Action Download a new firmware
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 598
    from the intended use. Recommended Action Change the port configuration (by deleting configured FCIP tunnels or iSCSI sessions) to return the port mode to neutral before attempting to configure the port for a different mode or use. IPS-1005 Message Tunnel Authorization Failure for slot (
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 599
    Indicates that the tunnel configuration failed because the FX8-24 blade is not at the correct revision to support IPSec enabled tunnels on VEs 22-31. Recommended Action Contact your switch vendor to acquire the correct hardware revision blade. Fabric OS Message Reference 577 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 600
    of the Internet Storage Name Service (iSNS) server is zero. Therefore, peering is disabled. Recommended Action If you wish to enable the iSNS server, use the isnscCfg command to show or set the server IP address; otherwise, no action is required. 578 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 601
    server IP address> slot/port /ge. Message Type LOG Severity INFO Probable Cause Indicates that the re-register with the specified external Internet Storage Name Service (iSNS) server has started. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 602
    Slot/port /ge is out of range. Message Type LOG Severity WARNING Probable Cause Indicates that the slot or port is out of range. Recommended Action Retry with a valid slot and port. Refer to the appropriate hardware reference manual for valid slot and port ranges. 580 Fabric OS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 603
    on management port. Message Type LOG Severity INFO Probable Cause Indicates that peering has started with the specified external Internet Storage Name Service (iSNS) on the management port. Recommended Action No action is required. Fabric OS Message Reference 581 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 604
    link was not established between the switch and the key vault. Recommended Action Establish a trustee link between the switch and the key vault. Refer to the Fabric OS Encryption Administrator's Guide for instructions to establish a trusted link. 582 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 605
    . Recommended Action Determine whether the configured key vault is operational; if not, change the switch key vault settings or resolve the operational problem at the key vault. KAC- key vaults using instructions provided by the key vault provider. Fabric OS Message Reference 583 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 606
    Keyvault IP Address>. Error code=, string=. Message Type LOG Severity WARNING Probable Cause Indicates that archiving of Data Encryption Data Encryption Key (DEK) from the key vault failed. Recommended Action No action is required. 584 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 607
    Data Encryption Key (DEK) to the key vault failed. Recommended Action No action is required. KAC-1014 Message Retrieval of Actual DEK from the KV
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 608
    between the configured key vault parameters on the Brocade Encryption Switch (BES) and the functionality supported by the key vault. Recommended Action De-register the key vaults, set the correct value for key vault parameter, and re-register the key vaults. 586 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 609
    ID>. Message Type FFDC | LOG Severity WARNING Probable Cause Indicates that a process on the switch has ended unexpectedly. Recommended Action Copy the warning message along with any core file information and contact your switch service provider. Fabric OS Message Reference 587 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 610
    Probable Cause Indicates that the advanced technology attachment (ATA) dump driver is not initialized properly. Recommended Action Execute the supportSave command and reload the switch. If the problem persists, contact your switch service provider. 588 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 611
    error code>. Message Type LOG Severity ERROR Probable Cause Indicates that trace was unable to initialize. Recommended Action Execute the supportSave command and reload the switch. If the problem persists, contact your switch service provider. Fabric OS Message Reference 589 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 612
    Error: Message queue create failed. Message Type LOG Severity ERROR Probable Cause Indicates that the Layer 2 system (L2SYS) encountered system service manager (SSM) message queue errors. Recommended Action Reboot or power cycle the switch. 590 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 613
    control (MAC) address table on the chip is 95 percent full. Recommended Action Clear some of the entries using the no mac-address-table static command or wait until the old entries age out. Fabric OS Message Reference 591 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 614
    Message Hardware GID limit reached on chip , GID limit at . Message Type LOG Severity INFO Probable Cause Indicates that all dynamic group IDs (GIDs) are allocated. Recommended Action Clear some of the ACL entries using the clear counters access-list mac command. 592 Fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 615
    ERROR Probable Cause Indicates an error in the hardware or the driver of the Layer 3 subsystem (L3SS). L3SS may have passed invalid parameters or the hardware Content Addressable Memory (CAM) may be full. Recommended Action Retry or clear the CAM. Fabric OS Message Reference 593 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 616
    new firmware using the firmwareDownload command. LACP-1002 Message . Message Type LOG Severity ERROR Probable Cause Indicates that some of the fields received in the Link Aggregation Control Protocol Data Unit (LACPDU) are invalid. Recommended Action No action is required. 594 Fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 617
    failed. Disabling port. Message Type LOG Severity ERROR Probable Cause Indicates that the specified port has crashed unexpectedly and restarting attempts have failed. Recommended Action Power cycle the blade using the slotPowerOff and slotPowerOn commands. Fabric OS Message Reference 595 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 618
    that the Logical Fabric Manager service is enabled. Note that the Logical Fabric Manager service is enabled by the factory setting and it is not user-configurable. Recommended Action No action is required. LFM-1003 Message The Logical Fabric Manager configuration is set to default. Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 619
    Probable Cause Indicates that the firmware version on the specified switch is not compatible with XISL. Recommended Action Check the release notes to verify if this firmware is compatible with XISL. If it is not, remove the switch from the fabric. Fabric OS Message Reference 597 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 620
    for non-bladed switches or the haFailover command on bladed switches. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 598 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 621
    switch service provider. LOG-1005 Message Log message has been disabled. Message Type AUDIT | LOG Class RAS Severity INFO Probable Cause Indicates that the specified message has been disabled from logging. Recommended Action No action is required. Fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 622
    Indicates that the specified module has been disabled from logging. Recommended Action No action is required. LOG-1008 Message Log Module has been enabled for logging. Recommended Action No action is required. 600 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 623
    specified internal message has been enabled for syslog logging. Recommended Action No action is required. LOG-1010 Message Internal Log message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 624
    1 through 239. The switch will discard the record because it is not supported. Recommended Action No action is required. LSDB-1002 Message Local switch generates its local LSR when first enabled. By disabling and enabling the switch, a new local LSR is generated. 602 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 625
    Recommended Action Run the switchDisable and switchEnable commands. A new local LSR is generated during the switch enable. LSDB-1004 Message No Link State Action No action is required. The other switch will pass the LSR after the fabric is stable. Fabric OS Message Reference 603 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 626
    Severity ERROR Probable Cause Indicates that the error has occurred while processing the hardware abstraction layer (HAL) message. Recommended Action Restart the multicast subsystem (MCAST_SS) . Recommended Action Restart the MCAST_SS daemon. 604 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 627
    port . Message Type LOG Severity ERROR Probable Cause Indicates that the multicast subsystem (MCAST_SS) has encountered an error during a network service received from the driver is invalid. Recommended Action Restart the MCAST_SS daemon. Fabric OS Message Reference 605 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 628
    ERROR Probable Cause Indicates that the multicast subsystem (MCAST_SS) has encountered the hardware abstraction layer (HAL) errors. Recommended Action Restart the MCAST_SS daemon. MCAST_SS- errors. Recommended Action Restart the MCAST_SS daemon. 606 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 629
    Action Restart the MCAST_SS daemon. MCAST_SS-1011 Message IDB error: () port id not found. Message Type LOG Severity ERROR Probable Cause Indicates that that the group address lookup for the specified VLAN has failed. Fabric OS Message Reference 607 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 630
    Message Type LOG Severity ERROR Probable Cause Indicates that the specified hardware subsystem layer (HSL) related operation has failed. Recommended Action Restart from the driver is invalid. Recommended Action Restart the MCAST_SS daemon. 608 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 631
    5 MCAST_SS-1017 Message Learning error: () Invalid number for ifindex . Message Type LOG Severity ERROR Probable Cause Indicates that during the Ptree operation. Recommended Action Restart the MCAST_SS daemon. Fabric OS Message Reference 609 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 632
    > MAC group . Message Type LOG Severity ERROR Probable Cause Indicates that the multicast subsystem (MCAST_SS) has encountered an error during the List operation. Recommended Action Restart the MCAST_SS daemon. 610 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 633
    environments. Recommended Action No action is required if SB-3 link incident registration and reporting is not used by the host or if default values are desired for the switch node descriptor fields. MFIC-1003 Message Effective Insistent domain ID for the fabric changed from to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 634
    , and no action is required. IDID mode can be set using the configure command in the CLI or checking the Advanced Web Tools Switch Admin > Configure > Fabric > Insistent Domain ID Mode check box. The switch must be disabled to change the IDID mode. 612 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 635
    in the VPD block 0 is bad. This could indicate corruption or tampering. Recommended Action Execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 613 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 636
    . Message Type LOG Severity WARNING Probable Cause Indicates that the fabric shortest path first (FSPF) module has determined that there is no minimum cost path (MPATH) available in the candidate list. Recommended Action No action is required. 614 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 637
    Action No action is required. MQ-1005 Message queue : queue full (miss=). Message Type LOG Severity WARNING Probable Cause Indicates that the specified message queue is full. Recommended Action No action is required. Fabric OS Message Reference 615 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 638
    size>). Message Type LOG Severity WARNING Probable Cause Indicates the incoming message size is larger than the message queue size. Recommended Action No action is required. 616 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 639
    firmwareDownload command to upgrade the firmware level on the switch to a level that supports reliable commit service (RCS). RCS is supported in Fabric OS v2.6, v3.1 and later, and v4.1 and later. • Reject EXGPLDB from: Wait a few minutes and try the command again. Fabric OS Message Reference 617
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 640
    the number of domains matches the Management Server known domains. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 618 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 641
    to write a message to the MS Extended Link Service Queue. • while inserting timer to timer list: MS is unable to add a timer to a resource. Recommended Action If the error persists, check the available memory on the switch using the memShow command. Fabric OS Message Reference 619 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 642
    that the Fabric OS state synchronization (FSS) warm recovery failed during the WARM INIT phase of a reboot. Recommended Action If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 643
    a failover occurred when Management Server (MS) platform service was being enabled. This can leave the fabric in an inconsistent state. Recommended Action If any inconsistency in MS platform service exists within the fabric, enable MS platform service. Fabric OS Message Reference 621 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 644
    Action Enable MS platform service on the switch and re-enable the port to join the fabric. MS-1027 Message Fabric Name - configured. Message Type AUDIT | LOG Class FABRIC Severity INFO Probable Cause Indicates that the specified fabric name is configured or renamed. Recommended
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 645
    . Message Type AUDIT | LOG Class FABRIC Severity ERROR Probable Cause Indicates that fabric name configure or clear operation failed in Fibre Channel Router (FCR). Recommended Action Wait for fabric to stabilize and retry the operation. Fabric OS Message Reference 623 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 646
    usage on the switch using the memShow command. Restart or power cycle the switch. MSTP-1002 switch, execute the haFailover command. If the problem persists or if this is a non-bladed switch, download a new firmware version using the firmwareDownload command. 624 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 647
    . MSTP-2003 Message MSTP instance is created. Message Type LOG Severity INFO Probable Cause Indicates that the specified multiple spanning tree protocol (MSTP) instance has been created. Recommended Action No action is required. Fabric OS Message Reference 625 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 648
    spanning tree protocol (MSTP) instance has been deleted. Recommended Action No action is required. MSTP-2005 Message VLAN is on MSTP instance . priority has been modified. Recommended Action No action is required. 626 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 649
    . Recommended Action Run the nbrStateShow command to check the neighbor state of the port listed in the message. If it is Full, then this message can safely be ignored. Otherwise, run the portDisable and portEnable commands to refresh the port. Fabric OS Message Reference 627 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 650
    two switches. Recommended Action Run the nbrStateShow command to check the neighbor state of the port listed in the message. If it is Full, then this message can safely be ignored. Otherwise, run the portDisable and portEnable commands to refresh the port. 628 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 651
    the maximum frame size the remote switch can handle. Recommended Action Execute the firmwareDownload command to upgrade the remote switch with Fabric OS v4.3 or later, or Fabric OS v3.2 or later, as appropriate for the switch type, so that it can support GMI to handle frame fragmentation and
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 652
    commands will be disruptive. Recommended Action To avoid disruption of traffic in the event of an unplanned failover, schedule a firmware download so 1024 or smaller, or upgrade the software of the remote switch to support 2048 zones. NS-1006 Message Duplicate WWN was detected with PID 0x
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 653
    with a duplicate WWN. NS-1007 Message NS has detected a logical ISL port in TI zone in fabric . Routing Action Install the Open FR license or relocate Open FR devices to a licensed switch. NS-1009 Message NS has detected a device with Node WWN as
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 654
    service (QoS) zone. Recommended Action Remove the CS_CTL configured devices from the QoS zone. NS-1011 Message NS has detected a failover flag disabled TI zone in a base switch in fabric ID
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 655
    command and resolve the protocol dependencies. The following are the possible reason codes: • Admin port-channel interfaces) • DOT1x authentication failed • BRCD remote link negotiation failed/LLDP disabled • LAG negotiating/failed • LAG admin state is down • UNKNOWN Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 656
    sessions from the FCoE VLAN member ports and then disable the FCoE VLAN. NSM-1006 Message FCoE on VLAN: has been disabled successfully. Message Type LOG Severity INFO Probable Cause Indicates that FCoE has been disabled on the specified VLAN. 634 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 657
    the chassis has been enabled or disabled. Recommended Action No action is required. NSM-1008 Message Blade () is . Message Type has been enabled or disabled. Recommended Action No action is required. NSM-1009 Message Interface is deleted. Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 658
    No action is required. NSM-1012 Message VLAN classifier group is created. Message Type LOG Severity INFO Probable Cause Indicates that the specified VLAN classifier group has been created. Recommended Action No action is required. 636 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 659
    action is required. NSM-1014 Message VLAN classifier rule is created. Message Type classifier rule has been created. Recommended Action No action is required. NSM-1015 Message has been deleted. Recommended Action No action is required. NSM-1016 Message VLAN classifier rule
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 660
    INFO Probable Cause Indicates that the logical interface member list has been changed. Recommended Action No action is required. NSM-1018 Message VLANs interface has changed to up. Recommended Action No action is required. 638 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 661
    . Message Type LOG Severity INFO Probable Cause Indicates that the administrative status of the specified interface has changed to down. Recommended Action No action is required. Fabric OS Message Reference 639 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 662
    is required. ONMD-1002 Message LLDP global configuration is changed. Message Type LOG Severity INFO Probable Cause Indicates that the link layer discovery protocol (LLDP) global configuration has been changed. Recommended Action No action is required. 640 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 663
    INFO Probable Cause Indicates that the auto-sense feature is used to detect the Data Center Bridging eXchange (DCBX) version on the specified interface. The DCBX version field on the link neighbor. Recommended Action No action is required. Fabric OS Message Reference 641 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 664
    Parity Data Manager (PDM) process. Recommended Action Execute the firmwareDownload command to reinstall the firmware. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 665
    Probable Cause Indicates that the Parity Data Manager (PDM) failed to register with the Fabric OS synchronization service (FSS). Recommended Action Execute the firmwareDownload command to reinstall the firmware. If the message persists, execute the supportFtp command (as needed) to set up
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 666
    your switch service provider. PDM-1009 Message Can't update Port Config Data. Message Type LOG Severity WARNING Probable Cause Indicates that the Parity Data Manager (PDM) system call to setCfg failed. Recommended Action Execute the firmwareDownload command to reinstall the firmware. If
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 667
    Action Execute the firmwareDownload command to reinstall the firmware. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 645 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 668
    Execute the firmwareDownload command to reinstall the firmware. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 646 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 669
    Action Execute the firmwareDownload command to reinstall the firmware. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 647 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 670
    Indicates that the Parity Data Manager (PDM) cannot synchronize with its peer because the Domain Name Service (DNS) is configured with IPv6 addresses. IPv6 is not supported by older firmware. Recommended Action Configure DNS with IPv4 addresses. 648 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 671
    Cause Indicates that the Parity Data Manager (PDM) cannot synchronize with its peer because the user-defined roles are configured. User-defined roles are not supported by older firmware. Recommended Action Remove user-defined roles configuration. Fabric OS Message Reference 649 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 672
    are as follows: • 0x10000000 - The watchdog timer (WDT) forced a core reset. • 0x20000000 - The WDT forced a chip reset. • All other code values are reserved. Recommended Action Run the pdShow command to view the panic dump and core dump files. 650 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 673
    the system manually using the reboot command. Execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. PLAT-1001 Message CP resetting other CP
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 674
    on core blades that are powered off, and power cycle or replace the core blades that are faulted. Run the chassisenable command to re-enable the ports. Running the fastboot or reboot command will also result in enabling the logical switches and ports. 652 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 675
    Action No action is required. PMGR-1002 Message Attempt to create switch failed. Error message: . Message Type LOG Severity WARNING Probable Cause Indicates that the switch with the specified fabric ID (FID) was not created. Recommended Action Refer to the Error Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 676
    Probable Cause Indicates that the switch with the specified fabric ID (FID) was not deleted. Recommended Action Refer to the Error Message string ports to the specified switch. Recommended Action No action is required. PMGR-1006 Message Attempt to move port(s) on slot to switch
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 677
    Action No action is required. PMGR-1008 Message Attempt to change switch to switch failed. Error message: . Message Type LOG Severity WARNING Probable Cause Indicates a failed attempt to change the switch fabric ID (FID). Recommended Action Refer to the Error
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 678
    5 PMGR-1011 PMGR-1011 Message Attempt to move port(s) to switch succeeded. Message Type LOG Severity INFO Probable Cause Indicates a successful attempt to move the ports to the specified switch. Recommended Action No action is required. 656 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 679
    and replace (if necessary) the hardware attached to both ends of the specified port number, including: • The media (SFPs) • The cable (fiber optic or copper inter-switch link (ISL)) • The attached devices After checking the hardware, execute the portEnable command to re-enable the port. PORT-1004
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 680
    does not support L_Port. If an E_Port or F_Port is connected, then the port will not come up because it is configured to be an L_Port. Recommended Action Execute the portCfgLport command to clear the L_Port configuration. PORT-1006 Message Configuration changed for port (ID: ) in
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 681
    QoS is disabled. Message Type LOG Severity INFO Probable Cause Indicates that the port quality of service (QoS) is disabled due to the best effort setting on the 4 Gbps or 8 Gbps long distance platform. Recommended Action No action is required. Fabric OS Message Reference 659 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 682
    Advanced Performance Monitoring configuration updated due to change in PID format. Message Type LOG Severity INFO Probable Cause Indicates that the port ID (PID) format was changed. Recommended Action No action is required. Refer to the Fabric OS Administrator's Guide for more information
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 683
    restoring configuration has attempted to add end-to-end monitors on at least one inter-switch link (ISL) port. Recommended Action No action is required. End-to-end monitoring is not supported on ISL ports when ISL monitoring is enabled. ISL monitoring can only be disabled through the Fabric Access
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 684
    Type LOG Severity WARNING Probable Cause Indicates that end-to-end monitors are configured on the switch. Recommended Action Delete end-to-end monitors on the switch and re-install the fabric mode Top Talker monitor. End-to-end monitors and fabric mode Top Talker monitors are mutually exclusive
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 685
    Type LOG Severity CRITICAL Probable Cause Indicates that Top Talker on the specified port has been removed due to memory allocation failure. Recommended Action Install Top Talker again on the specified port using the perfttmon --add command. Fabric OS Message Reference 663 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 686
    is 0x and port is 0x. Message Type LOG Severity INFO Probable Cause Indicates the portSwap command has been issued. Recommended Action No action is required. PSWP-1002
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 687
    number . Message Type LOG Severity WARNING Probable Cause Indicates the bladeSwap command failed on access to configuration data. Recommended Action Retry the command. If the failure persists, contact your switch service provider. Fabric OS Message Reference 665 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 688
    number . Message Type LOG Severity WARNING Probable Cause Indicates the bladeSwap command failed on access to switch context. Recommended Action Retry the command. If the failure persists, contact your switch service provider. 666 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 689
    execute the supportSave command and contact your switch service provider. RAS-1002 Message First failure data capture (FFDC) maximum command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 690
    (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. RAS-1006 Message Support data file () automatically transferred to remote address ' '. Message Type LOG Severity
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 691
    message class configuration has been changed to . Message Type LOG | AUDIT Class RAS Severity INFO Probable Cause Indicates that the audit event class configuration has been changed. Recommended Action No action is required. Fabric OS Message Reference 669 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 692
    Recommended Action No action is required. RAS-3002 Message USB command before unplugging it from the system. RAS-3004 Message USB storage device disabled. Message Type LOG Severity INFO Probable Cause Indicates that the USB storage device has been disabled. 670 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 693
    Action No action is required. RAS-3005 Message CLI: . Message Type AUDIT Class CLI Severity INFO Probable Cause Indicates that the specified command was executed on console. Recommended Action No action is required. RAS-3005 5 Fabric OS Message Reference 671 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 694
    is supported in Fabric OS v2.6, v3.1 and later, and v4.1 and later. Run the firmwareDownload command to upgrade the firmware for any switches that do not support RCS. RCS-1002 Message RCS has been enabled. Message Type LOG Severity INFO Probable Cause Indicates that the reliable commit service
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 695
    minutes and then retry the operation from the sender switch. If the reject is in the stage fabric configuration (SFC) phase, check if the application license exists for the local domain and if the application data is compatible. RCS-1006 Message State , Application
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 696
    application license exists for the remote domain and if the application data is compatible. RCS fabric because it does not support reliable commit service (RCS). Recommended Action Run the fabricShow command to verify that the remote domain is out of the fabric. 674 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 697
    from domain . Message Type LOG | FFDC Severity WARNING Probable Cause Indicates that the specified domain is RCS-incapable. Recommended Action Execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 675 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 698
    > is RCS incapable. Message Type LOG | FFDC Severity WARNING Probable Cause Indicates that the specified remote domain is RCS-incapable. Recommended Action Execute the supportSave command and contact your switch service provider. 676 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 699
    required. RKD-1002 Message Could not start operation. . No response from cluster member WWN:
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 700
    Cause Indicates the generic re-key message. Recommended Action No action is required. RKD-1005 Message LUN with LSN: does no have Severity WARNING Probable Cause Indicates uncompressible data on blocks 1 through 16 of the LUN. Recommended Action Migrate the data on this LUN to a
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 701
    Check the traffic on the interface using the show interface command. Note that you can use the show interface command to check the traffic on the interface, provided the statistics on the interface are not cleared using the clear counters command. Fabric OS Message Reference 679 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 702
    Secure Sockets Layer (SSL) certificate file configured on the switch could not be accessed because root did not have read-level access. Recommended Action Change the file system access level for the certificate file to have root read-level access. 680 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 703
    secCertUtil command to install a valid private key file. RPCD-1006 Message Permission denied accessing private key file. Secure RPCd is disabled. Message Type LOG Severity WARNING Probable Cause Indicates the private key file configured on the switch could not be accessed because the root did
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 704
    5 RPCD-1007 Recommended Action Run the secCertUtil command to install a valid private key file. 682 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 705
    It may cause connectivity issues. If such issues arise, bounce all ISLs and ICLs on this chassis. Message Type LOG Severity WARNING Probable . Recommended Action Reset all E_ports on the chassis using the portDisable and portEnable commands. Fabric OS Message Reference 683 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 706
    ID is offline, enable the switch using the switchEnable command. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 684 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 707
    the fabricShow command to verify that the specified domain ID is reachable. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 685 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 708
    supportSave command to send the core files using FTP to a secure server location. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 686 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 709
    supportSave command to send the core files using FTP to a secure server location. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 687
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 710
    command and contact your switch service provider. SEC-1002 Message Security data fails: . Message Type LOG Severity ERROR Probable Cause Indicates that the receiving switch fails to validate the security database sent from the primary fabric configuration server (FCS) switch
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 711
    then execute the supportSave command and contact your switch service provider. SEC-1005 Message Primary FCS receives data request from domain . Message Type LOG Severity INFO Probable Cause Indicates the primary fabric configuration server (FCS) received a data request from the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 712
    Type LOG Severity INFO Probable Cause Indicates a security violation was reported. The IP address of the unauthorized host is displayed in the message. Recommended Action Check for unauthorized access to the switch through the Telnet connection. 690 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 713
    exist on the switch. If the private key does not exist, follow the steps for re-creating PKI objects outlined in the Fabric OS Administrator's Guide. If a certificate does not exist or is invalid, install the certificate by following the field upgrade process. Fabric OS Message Reference 691 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 714
    () detected. Message Type LOG Severity ERROR Probable Cause Indicates a corruption occurred during the distribution of the security database. This can occur only when the primary fabric configuration server (FCS) distributes the security database to the other switches in the fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 715
    configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the secFabricShow command to verify that the fabric is still consistent. All
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 716
    command supports use of the asterisk for adding switches to policies. Recommended Action Run the secPolicyAdd command using a valid switch identifier (WWN, domain ID, or switch name) to add specific switches to the Switch Connection Control (SCC) policy. 694 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 717
    secPolicyCreate or secPolicyAdd command with a properly formatted device name parameter. SEC-1037 Message Invalid WWN format . Message Type LOG Severity ERROR Probable Cause Indicates the WWN entered in the policy member list has an invalid format. Fabric OS Message Reference 695 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 718
    Action Run the command again using the standard WWN format; 16 hexadecimal port list contains the wildcard asterisk (*) character. You cannot use the asterisk in a port list. Recommended Action Enter the port list values without any wildcard characters. 696 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 719
    . SEC-1043 Message Invalid port range - . Message Type LOG Severity ERROR Probable Cause Indicates the specified port is not within the minimum and maximum range. Recommended Action Use valid syntax when entering port ranges. Fabric OS Message Reference 697 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 720
    the primary fabric configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the secFabricShow command to verify that the fabric is still
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 721
    SEC-1051 Message Missing brace for port list . Message Type LOG Severity ERROR Probable Cause Indicates a corruption occurred during the distribution of the security database. This can only occur when the primary fabric configuration server (FCS) distributes the security database to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 722
    Run the secFabricShow command to verify that the fabric is still consistent. All the switches should be in the ready state. If a switch is in the error state, the database may not be correctly updated for that specific switch. SEC-1054 Message Invalid FCS list length . Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 723
    FCS list . Message Type LOG Severity ERROR Probable Cause Indicates a corruption occurred during the distribution of the security database. This can only occur when the primary fabric configuration server (FCS) distributes the security database to the other switches in the fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 724
    failed when writing to flash memory. Recommended Action Run the supportFtp - e command to FTP files from the switch and remove them from the flash memory. SEC-1062 Message Invalid number of Domains in Domain List. Message Type LOG Severity ERROR Probable Cause Indicates that either no domains
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 725
    install the certificate by following the field upgrade process. SEC-1065 Message Invalid character in list. Message Type LOG Severity ERROR Probable Cause Indicates the input list the supportSave command and contact your switch service provider. SEC-1071 Message No new security policy data to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 726
    execute the supportSave command and contact your switch service provider. SEC-1073 Message No FCS policy in list. Message Type command was run on a switch that is not allowed to run it either because it is in non-secure mode or because it does not have the required fabric configuration server (FCS
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 727
    configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the secFabricShow command to verify that the fabric is still consistent. All
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 728
    No new data to abort. fabric configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the fabricShow command to verify that the fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 729
    configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the fabricShow command to verify that the fabric is still consistent. All the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 730
    in flash. Message Type LOG Severity ERROR Probable Cause Indicates the security database has more data than the flash memory can accommodate. Recommended Action Reduce the number of entries in some policies to decrease the security database size. 708 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 731
    when the primary fabric configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the fabricShow command to verify that the fabric is still
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 732
    configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the fabricShow command to verify that the fabric is still consistent. All the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 733
    ERROR Probable Cause Indicates the new fabric configuration server (FCS) list does not have a common member with the existing FCS list. Recommended Action Resubmit the command with at least one member of the new FCS list in common with the current FCS list. SEC-1094 Message Policy member not
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 734
    configuration. Recommended Action Verify the security policy configuration requirements and remove any policies that require command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 712 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 735
    that specific switch. SEC-1100 Message FCS switch present. Command terminated. Message Type LOG Severity ERROR Probable Cause Indicates a corruption occurred during the distribution of the security database. This can only occur when the primary fabric configuration server (FCS) distributes the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 736
    public key. Recommended Action Verify the primary switch has a valid certificate installed and retry the operation. If a valid certificate is not installed, install a certificate by following the procedure specified in the Fabric OS Administrator's Guide. SEC-1105 Message Fail to disable secure
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 737
    Recommended Action Run the secCertUtil show -fcapall command and verify that all PKI objects exist on the switch. If a failure to validate PKI objects occurs, follow the steps for re-creating PKI objects outlined in the Fabric OS Administrator's Guide. SEC-1107 Message Stamp is 0. Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 738
    same as the current active FCS list in the switch. Message Type LOG Severity ERROR Probable Cause Indicates either a security policy download was attempted with an active policy that does not have the fabric configuration server (FCS) policy as the first policy, or the FCS policy is not the same
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 739
    an attempted secFcsFailover, no primary FCS is present in the fabric. Recommended Action Run the secFabricShow command to verify that all switches in the fabric are in the ready state. When all switches are in the ready state, retry the operation. Fabric OS Message Reference 717 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 740
    failed to save the data received by the primary fabric configuration server (FCS) switch. This data can be an FCS password, a non-FCS password, SNMP data, or multiple user authentication data. Recommended Action Run the fabricShow command to verify that all switches in the fabric are in the ready
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 741
    could not communicate with the primary fabric configuration server (FCS). Recommended Action Run the fabricShow command to verify that all switches in the fabric are in the ready state. When all switches are in the ready state, retry the operation. Fabric OS Message Reference 719 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 742
    Type LOG Severity INFO Probable Cause Indicates the security database was successfully downloaded from the primary fabric configuration server (FCS). Recommended Action No action is required. SEC-1124 Message Secure Mode is off. Message Type LOG Severity INFO Probable Cause Indicates
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 743
    the security database sent from the primary fabric configuration server (FCS) switch. This message usually indicates that the data package is corrupted, the time stamp on the package is out of range as a result of a replay attack or out-of-sync time service, or the signature verification failed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 744
    the security database sent from the primary fabric configuration server (FCS) switch. This message usually indicates that the data package is corrupted, the time stamp on the package is out of range as a result of a replay attack or out-of-sync time service, or the signature verification failed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 745
    , and run the firmwareDownload command to upgrade the firmware. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 723 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 746
    message can also be caused when the switch is short of memory. The status Fabric-wide commands may take a few minutes to propagate throughout the fabric. Make sure to wait a few minutes between executing commands so that your commands do not overlap in the fabric. 724 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 747
    configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the secFabricShow command to verify that the fabric is still consistent. All
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 748
    command when a switch is already in secure mode. SEC-1164 Message Lockdown option cannot be applied on a non-FCS switch. Message Type LOG Severity ERROR Probable Cause Indicates the attempt to enable security is made on a switch that is not present in the fabric configuration server (FCS) list
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 749
    configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the secFabricShow command to verify that the fabric is still consistent. All
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 750
    whether all PKI objects exist. If they do not exist, run the secCertUtil command to create them for the switch. Run the licenseAdd command to install the required license key. Contact your switch supplier to obtain a license if you do not have one. SEC-1172 Message Failed to identify role
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 751
    is required; if not, check the primary FCS. SEC-1174 Message Failed to set password. Message Type LOG Severity ERROR Probable Cause Indicates the fabric configuration server (FCS) or non-FCS password could not be set. Recommended Action Verify all switches in the fabric are
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 752
    Severity ERROR Probable Cause Indicates the primary fabric configuration server (FCS) failed to generate a new version stamp because the fabric was not stable. Recommended Action Verify all switches in the fabric are in time synchronization with the primary FCS and that no external entity is
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 753
    the switch database was enabled or disabled as the secondary authentication, accounting, and authorization (AAA) mechanism when the remote authentication dial-in user service (RADIUS/LDAP/TACACS+) is the primary AAA mechanism. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 754
    , LDAP, or TACACS+ configuration was enabled or disabled as the primary authentication, accounting, and authorization (AAA) mechanism. Recommended Action No action is required. SEC-1187 Message Security violation: Unauthorized switch tries to join fabric. Message Type LOG Severity
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 755
    . Recommended Action Determine whether the host IP address specified in the message can be used to manage the fabric through an HTTP connection. If so, add the host IP address to the HTTP policy of the fabric. If the host is not allowed access to the fabric, this is a valid violation message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 756
    method; the login failed. Recommended Action The error message lists the violating IP address. Verify that this IP address is being used by a valid switch admin. Use the correct password. SEC-1194 Message This switch does not have all the required PKI objects correctly installed. Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 757
    the primary fabric configuration server (FCS) distributes the security database to the other switches in the fabric, and then local validation finds the error in the security database. This is a rare occurrence. Recommended Action Run the secFabricShow command to verify that the fabric is still
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 758
    forwarded from non-primary FCS switch. Message Type LOG Severity INFO Probable Cause Indicates a management server (MS) forward security violation was reported. A management server command was forwarded from a non-primary fabric configuration server (FCS) switch. Recommended Action Check the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 759
    : MS device operates on non-primary FCS switch. Message Type LOG Severity INFO Probable Cause Indicates a management server (MS) operation security violation was reported. An MS device operation occurred on a non-primary fabric configuration server (FCS) switch. Recommended Action
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 760
    , commit, or cancel phases. Recommended Action Retry the failed security command. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. 738 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 761
    Message This switch does not have all the required PKI objects correctly installed. Message Type LOG Severity INFO Probable Cause Indicates a corruption occurred during the distribution of the security database. This can only occur when the primary fabric configuration server (FCS) distributes
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 762
    Recommended Action Run the firmwareDownload command to update the firmware to the latest version for your specific switch. Verify the firmware you are installing supports the Brocade Secure Fabric OS feature. SEC-1304 Message This switch has no security license. Message Type LOG Severity INFO
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 763
    Action Run the secCertUtil show -fcapall command and verify that all public key infrastructure (PKI) objects exist on the switch. If a failure to validate PKI objects occurs, follow the steps for re-creating PKI objects outlined in the Fabric OS Administrator's Guide. If PKI objects are valid
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 764
    --setdefault command on each switch in the fabric to set the password policies to the default values. Then verify with the passwdCfg --show command that password policies are set to the default values on all switches and retry the secModeEnable command. 742 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 765
    LOG Severity ERROR Probable Cause Indicates the call to the environment monitor (EM) module to retrieve the IP address failed. Recommended Action Reboot the system to fix this error. If the problem persists, contact your switch service provider. Fabric OS Message Reference 743 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 766
    a switch that was configured not to accept distributions from the fabric. Recommended Action Verify the accept distribution configuration for the listed databases. Use the remoteeCfg command to verify and correct the configuration if necessary. SEC-1316 Message policy WWN List is
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 767
    that a domain not supporting an access control list (ACL) policy tried to join a fabric with the strict fabric-wide policy. Recommended Action No action is required. The domain is denied by disallowing all its E_Ports from connecting to the fabric. Fabric OS Message Reference 745 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 768
    Probable Cause Indicates this fabric is not able to support a Device Connection Control (DCC) policy with more than 256 ports. Recommended Action Reconfigure any policy that includes more than 256 ports in its member list, and then save the policy configuration changes. SEC-1323 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 769
    required unless the switch must remain in the fabric. If the switch must remain in the fabric, add the switch World Wide Name (WWN) to the SCC policy, and then attempt to join the switch with the fabric. SEC-1326 Message Event: fddcfg --fabwideset, Status: success, Info: Fabric wide configuration
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 770
    the IP filter policy enforcement failed because of an internal system failure. Recommended Action Execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 748 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 771
    FCS switch. Use the secPolicyShow command to verify and correct the configuration if necessary. SEC-1331 Message Attempt to enable secure mode failed. Reason: . Message Type LOG Severity ERROR Probable Cause Indicates the secModeEnable command failed on the fabric because default IP
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 772
    SEC-1333 Message command failed. There are VF enabled switch(s) in fabric. db(s) is required. The domain is denied by disallowing all its E_Ports connected to the fabric. If the domain should be allowed to merge with the fabric, then
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 773
    password configuration parameters changed. Recommended Action Verify the security event was planned. If the security event was planned, no action is required. If the security event was not planned, take appropriate action as defined by your enterprise security policy. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 774
    . The event can be one of the following: • There has been a fabric configuration server (FCS) failover. • A security policy has been activated. • A security policy has been saved. • A security policy has been aborted. • A non-FCS password has changed. 752 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 775
    planned. If the security event was planned, no action is required. If the security event was not planned, take appropriate Name>, Status: success, Info: Created policy, with member(s) . Message Type AUDIT Class field. Fabric OS Message Reference 753 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 776
    is required. FCS position> to . Message Type AUDIT Class SECURITY Severity INFO Probable Cause Indicates the fabric configuration server (FCS) list has been modified. One of the members of the list has been moved to a new position in the list. 754 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 777
    aborted, no action is required. If the security transaction Reset [] statistics on domain(s) []. Message Type AUDIT Class SECURITY Severity INFO Probable Cause Indicates a user has reset a security statistic on the specified domains. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 778
    Name>, Status: success, Info: server for AAA services. Message Type AUDIT Class SECURITY Severity INFO Probable Cause Indicates a user has changed the RADIUS, LDAP, or TACACS+ configuration. 756 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 779
    changed. If the remote server position was intentionally changed, no action is required. If the remote server position was not intentionally changed, take appropriate Cause Indicates a user has changed the RADIUS, LDAP, and TACACS+ configuration. Fabric OS Message Reference 757 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 780
    . If the password configuration parameter was intentionally set to default values, no action is required. If the password configuration parameter was not intentionally set to default values, take appropriate action as defined by your enterprise security policy. 758 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 781
    required. If the security event was not planned, take appropriate action as defined by your enterprise security policy. SEC-3021 Message Event: , Status: failed, Info: Failed login attempt via
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 782
    user account was created. Recommended Action Verify the security event was planned. If the security event was planned, no action is required. If the security event was not planned, take appropriate action as defined by your enterprise security policy. 760 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 783
    account was deleted. Recommended Action Verify the security event was planned. If the security event was planned, no action is required. If the security event was not planned, take appropriate action as defined by your enterprise security policy. Fabric OS Message Reference 761 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 784
    Status: success, Info: Distributed db(s) to domain(s), dom-id(s). Message Type AUDIT is required. If the event was not planned, take appropriate action as defined by your enterprise security policy. 762 Fabric OS Message Reference 53-
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 785
    : success, Info: Switch is configured to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 786
    IP filter policy has been activated. Recommended Action Verify the security event was planned. If the security event was planned, no action is required. If the security event was not planned, take appropriate action as defined by your enterprise security policy. 764 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 787
    The IP address of the unauthorized host is displayed in the message. Recommended Action Check for unauthorized access to the switch through is required. If the security event was not planned, take appropriate action as defined by your enterprise security policy. Fabric OS Message Reference 765
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 788
    a CLI command: is failed. Message Type AUDIT Class SECURITY Severity INFO Probable Cause Indicates the user does not have permission to execute this command. Recommended Action Verify the user has the required permission to execute this command. 766 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 789
    bootprom access is changed using fipscfg CLI to : . Message the fipsCfg command. Recommended Action No action is required. SEC-3050 required. If the security event was not planned, take appropriate action as defined by your enterprise security policy. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 790
    Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates that a license key is added or removed. Recommended Action No action is required. SEC-3061 Message Role '' is created. Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates that
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 791
    SEC-3065 Message Configuration of user-defined roles is uploaded. Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates the configuration of user-defined roles has been uploaded. Recommended Action No action is required. Fabric OS Message Reference 769 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 792
    cipher list. SEC-4001 Message Client logged in. , , . Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates the client has logged in. Recommended Action No action is required. 770 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 793
    globally enabled or disabled. Recommended Action No action is required. SFLO-1002 Message sFlow is for port . Message Type LOG Severity INFO Probable Cause Indicates the specified value. Recommended Action No action is required. Fabric OS Message Reference 771 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 794
    been changed on the specified port. Recommended Action No action is required. SFLO-1007 Message is as sFlow collector. Message Type LOG Severity INFO Probable Cause Indicates that the sFlow collector is configured or not configured. 772 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 795
    No action is required. SFLO-1008 Message All the sFlow collectors are unconfigured. Message Type LOG Severity INFO Probable Cause Indicates that none of the sFlow collectors are configured. Recommended Action No action is required. SFLO-1008 5 Fabric OS Message Reference 773 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 796
    ERROR Probable Cause Indicates that the Simple Network Management Protocol (SNMP) service could not be started because of the specified reason. Therefore, you will not be able to query the switch through SNMP. Recommended Action Verify that the IP address for the Ethernet and Fibre Channel
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 797
    AUDIT | LOG Class CFG Severity INFO Probable Cause Indicates that the specified SNMP configuration group was reset to the factory default. Recommended Action Execute the snmpConfig --show command for the group to view the new SNMP configuration. Fabric OS Message Reference 775 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 798
    port . Message Type AUDIT | LOG Class CFG Severity INFO Probable Cause Indicates the blocked or unblocked status of the port traps on the specified port. Recommended Action Execute the snmpTraps --show command to view the current status of the port. 776 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 799
    on an encryption engine. Recommended Action No action is required. SPC-1002 Message S, and slotPowerOn commands on the blade. To recover a non-bladed system, execute the fastboot command on the switch. Fabric OS Message Reference 777 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 800
    commands. SPC-2003 Message S, : Data Disable status: 0x. Message Type LOG Severity INFO Probable Cause Indicates the data disable signal status. Recommended Action No action is required. 778 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 801
    download has failed. Recommended Action No action is required. SPC-2005 Message S, : FPGA firmware download Crypto Power-On Self-Test (POST) tests have failed. Recommended Action No action is required. Fabric OS Message Reference 779
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 802
    INFO Probable Cause Indicates that Crypto Power-On Self-Test (POST) has passed successfully. Recommended Action No action is required. SPC-2008 Message S
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 803
    required. SPC-2012 Message S, : User zeroization command command has completed successfully. The encryption engine is zeroized. Recommended Action Execute the cryptocfg --initEE and cryptocfg --regEE commands. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 804
    hardware failure. Recommended Action The shelf life of the system may be reduced. Contact the vendor for further instructions will be unaffected while the facility power is present. Schedule battery replacement with the vendor. SPC-2040 required. 782 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 805
    an allocation failure for the pool of SB message. Recommended Action No action is required. SPC-2042 Message S, : Alloc msg queue has overflowed. Recommended Action No action is required. Fabric OS Message Reference 783 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 806
    is not opened. Recommended Action No action is required. SPC-3001 Message S
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 807
    required. The KEK will be recovered automatically. SPC-3004 Message S, : No output KEK for DEK create the data encryption key (DEK) to be created does not switch service provider for assistance. Fabric OS Message Reference 785 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 808
    ; otherwise, contact your switch service provider. SPC-3007 Message S, : DEK create error: , info: . Message Type LOG Severity ERROR Probable Cause Indicates an error in creating data encryption key (DEK
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 809
    has been started. Recommended Action No action is required. SPC-3009 Message S
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 810
    Cause Indicates that an attempt to store CryptoModule internal data using the Secret Encryption Key failed; most likely the cryptocfg --initEE and cryptocfg --regEE commands, and then recover or restore the switch service provider for assistance. 788 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 811
    internal random number generator has failed. Recommended Action Contact your switch service provider for assistance. SPC-3015 Message S
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 812
    command and contact your switch service provider. SPM-1003 Message Set New Group Cfg SC Enable KV Type . Message Type LOG Severity INFO Probable Cause Indicates a new group has been configured. Recommended Action No action is required. 790 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 813
    node initialization. Recommended Action No action is required. SPM-1005 Message Set EE Control slot . Recommended Action No action is required. SPM-1006 Message Registered Certificate registration. Recommended Action No action is required. SPM-1007 Message Deregistered Certificate cid
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 814
    (SP) certificate de-registration. Recommended Action No action is required. SPM-1009 Message Certificate is missing. Message Type specified certificate is missing. Recommended Action Execute the cryptocfg --initnode command. SPM-1010 Message Key Vault Certificate is missing.
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 815
    Cause Indicates that a group configuration has changed the quorum size. Recommended Action No action is required. SPM-1012 Message Authentication Action Execute the cryptocfg --sync -securitydb command to manually sync the security database. Fabric OS Message Reference 793 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 816
    different versions of FOS. Message Type LOG Severity WARNING Probable Cause Indicates a failure to distribute the security database. Recommended Action Use the cryptocfg --sync -securitydb command to manually sync security database. 794 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 817
    Probable Cause Indicates an encryption engine was initialized. Recommended Action No action is required. SPM-3003 Message Event: cryptocfg Status: success, Info: EE in slot engine was registered. Recommended Action No action is required. Fabric OS Message Reference 795 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 818
    Probable Cause Indicates an encryption engine was enabled. Recommended Action No action is required. SPM-3005 Message Event: cryptocfg Status: success, Info: EE in slot exported through SCP protocol. Recommended Action No action is required. 796 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 819
    No action is required. SPM-3009 Message Event: cryptocfg Status: success, Info: DH response accepted. Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates a DH response was accepted. Recommended Action No action is required. Fabric OS Message Reference 797 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 820
    Certificate label: \"\" Certificate file: \"\" IP address: . Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates a key vault was registered. Recommended Action No action is required. 798 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 821
    a key archive client (KAC) certificate was registered. Recommended Action No action is required. SPM-3015 Message Event: cryptocfg Status: success, Info: Key vault type set to key vault type was set. Recommended Action No action is required. Fabric OS Message Reference 799 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 822
    Probable Cause Indicates a master key was generated Recommended Action No action is required. SPM-3017 Message Event: cryptocfg Status: success, Info: Master key exported a master key was recovered. Recommended Action No action is required. 800 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 823
    Cause Indicates a system card was registered. Recommended Action No action is required. SPM-3020 Message Event: cryptocfg Status: success, Info: System card with an authentication card was registered. Recommended Action No action is required. Fabric OS Message Reference 801 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 824
    Indicates use of the system card was enabled or disabled. Recommended Action No action is required. SPM-3024 Message Event: cryptocfg Status: success, Info: Quorum size set to the quorum size was set. Recommended Action No action is required. 802 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 825
    card registered. Certificate label: \"\" Certificate file: \"\". Message Type AUDIT | LOG Class SECURITY Severity INFO Probable Cause Indicates a recovery card was registered. Recommended Action No action is required. Fabric OS Message Reference 803 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 826
    Cause Indicates an encryption engine state has changed. Recommended Action No action is required. SPM-3029 Message Event: KeyVault Connection Status: , Info: KAC_Connect: the status of key vault. Recommended Action No action is required. 804 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 827
    INFO Probable Cause Indicates that the supportSave command was used to transfer support information to a remote location. Recommended Action No action is required. SS-1001 Message supportSave's upload operation to host IP address aborted. Message Type LOG Severity WARNING Probable
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 828
    control processor (CP) and the blade in the specified slot. Recommended Action Check for the IP connection between the active CP and the blade in the specified slot. After the IP connection is established, execute the supportSave command again. 806 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 829
    blade in the specified slot. Recommended Action Restart the switch using the reboot command and then execute the supportSave command. SS-1007 Message supportsave failed for the slot < . Recommended Action Execute the supportSave command again. Fabric OS Message Reference 807 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 830
    address . Message Type LOG Severity INFO Probable Cause Indicates that the supportSave command was used to transfer core and first failure data capture (FFDC) files to a remote location. Recommended Action No action is required. SS-1011 Message CORE/FFDC files have been transferred
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 831
    enough disk space in the secondary partition of the active CP to save the supportsave files, before uploading them to the remote host. Recommended Action Manually clean up the secondary partition of the active CP to collect the supportsave files. Fabric OS Message Reference 809 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 832
    command. Restart or power cycle the switch. SSMD-1002 Message Failed to initialize rc = . Message Type LOG Severity ERROR Probable Cause Indicates that the initialization of a module within System Services Manager (SSM) has failed. Recommended Action Download a new firmware
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 833
    that Data Center Ethernet (DCE) SSM encountered an unexpected severe error during basic startup and initialization. Recommended Action Restart or power cycle the switch. If the problem persists, download a new firmware using the firmwareDownload command. SSMD-1006 Message Error while configuring
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 834
    extended access control lists (ACLs). SSMD-1200 Message QoS failed programming ASIC /
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 835
    for enforcing interface Priority-based Flow Control (PFC) flow control feature. Recommended Action Delete and reapply the QoS PFC flow control policy using the qos flowcontrol pfc command. If the problem persists, restart or power cycle the switch. Fabric OS Message Reference 813 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 836
    the CEE Map Class of Service (CoS) to Priority Group ID (PGID) mapping feature. Recommended Action Delete and reapply the CEE Map CoS to PGID policy using the cee-map default command. If the problem persists, restart or power cycle the switch. 814 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 837
    an unexpected error in programming the dataplane ASIC for enforcing the interface Default CoS feature. Recommended Action Delete and reapply the QoS interface Default CoS policy using the qos cos command. If the problem persists, restart or power cycle the switch. SSMD-1208 Message QoS failed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 838
    the multicast packet Scheduler Control feature. Recommended Action Delete and reapply the QoS multicast packet Scheduler Control policy using the qos queue multicast scheduler command. If the problem persists, restart or power cycle the switch. 816 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 839
    the dataplane ASIC for enforcing the interface CoS Tail Drop Threshold feature. Recommended Action Delete and reapply the QoS CoS Tail Drop Threshold policy using the qos rcv-queue command. If the problem persists, restart or power cycle the switch. Fabric OS Message Reference 817 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 840
    or power cycle the switch. SSMD-1217 Message QoS CEE could not comply with FCoE scheduler ASIC. Recommended Action Redefine CEE Map and FCoE into a configuration that translates into an ETS scheduler policy requiring eight or fewer traffic classes. SSMD-1300 Message CEE Map is created
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 841
    been deleted. Recommended Action No action is required. SSMD-1302 Message CEE Map
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 842
    Action No action is required. SSMD-1307 Message access list is created. Message Type LOG Severity INFO Probable Cause Indicates that the specified access list has been created. Recommended Action No action is required. 820 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 843
    . Recommended Action No action is required. SSMD-1311 Message ACL is removed from interface . Message Type LOG Severity INFO Probable Cause Indicates that the specified access list has been removed from the interface. Fabric OS Message Reference 821 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 844
    profile map has been assigned to the interface. Recommended Action No action is required. SSMD-1313 Message removed from interface . Message CEE Map has been changed. Recommended Action No action is required. 822 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 845
    that the specified CEE Map is incompatible with the current firmware and therefore it is reset to the default. Recommended Action No action is required. SSMD-1316 Message CEE Map is reset to default configuration. Message Type LOG Severity INFO Probable Cause Indicates that the
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 846
    removed from interface . This operation could take a long time. Message Type LOG Severity INFO Probable Cause Indicates that the specified access list is being removed from the interface. Recommended Action No action is required. 824 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 847
    out after 30 minutes. Recommended Action Do not fail over or power down the system during firmware upgrade. Allow the firmwareDownload command to continue without disruption. No action is required. Run the firmwareDownloadStatus command for more information. SULB-1002 Message Firmwaredownload
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 848
    processor (CP) has now become the active CP and is running the new firmware version. Recommended Action No action is required. The firmwareDownload command is progressing as expected. Run the firmwareDownloadStatus command for more information. 826 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 849
    listed for completeness. TABLE 7 Status messages and status codes Status message Status code "Firmware download sanity check failed." "Sanity check failed because system is non-redundant." "Sanity check failed because firmware download is already in progress." "Sanity check failed because Fabric
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 850
    "Firmware download has completed successfully on standby CP." "Standby CP reboots." Status code 0x34 0x35 0x36 0x37 0x40 0x41 0x42 0x43 0x44 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6a 0x6b 0x6c 0x6d 0x6e 828 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 851
    0x89 firmware status." "The firmwareDownload command has completed successfully." 0x8a "The original firmware has been restored successfully." 0x8b "Remote CP is restoring its secondary partition." 0x8c "Local CP is restoring its secondary partition." 0x8d Fabric OS Message Reference 829
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 852
    Check whether the switch is supported by the requested firmware. Also check the firmwareDownload help page for other possible failure reasons." 0x12 "The RPM package database is inconsistent. Contact your switch service provider for 0x13 recovery." 830 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 853
    "Firmware download is already in progress." 0x22 "Firmware download timed out." 0x23 "Out of disk space." 0x24 "Primary filesystem is inconsistent. Run the firmwareRestore command to restore 0x25 the original firmware, or contact your switch service provider for recovery." "The post-install
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 854
    RPM package." If this error occurs immediately after firmware download is started, the firmware on the switch may be two releases older than the requested firmware. The firmware download operation supports firmware upgrades within two feature releases (a feature release is indicated by a major
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 855
    the firmwareDownload -s command to upgrade the firmware on the standby CP to the same version as the active CP. Then retry the firmwareDownload command to download the desired version of firmware onto the CPs. Refer to the Fabric OS Troubleshooting Guide for troubleshooting information. SULB-1010
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 856
    and slotPowerOn commands to trigger another firmware download to the blade. If the blade is stuck in the LOADING state, remove and re-insert the blade to trigger another firmware download. If the problem persists, contact your switch service provider. 834 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 857
    and slotPowerOn commands to trigger another firmware download to the blade. If the blade is stuck in LOADING state, remove and re-insert the blade to trigger another firmware download. If the problem persists, contact your switch service provider. SULB-1021 Message Firmware is being downloaded to
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 858
    the end of the firmware commit, the blade firmware version is still inconsistent with the active CP firmware, firmware download will be restarted automatically on the blade. Run the firmwareDownloadStatus command to monitor the progress. If the problem persists, contact your switch service provider
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 859
    be an error caused by an unexpected disruption of the firmwareDownload command; for example, by powering the switch off and on in the middle of a firmware download. The error may also be caused by persistent storage hardware failure or by a software error. Recommended Action The firmwareDownload
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 860
    persistent storage hardware failure. Recommended Action Reboot the switch. This will cause the internal image to be relocated again. Use the firmwareDownloadStatus command to monitor the progress. If the problem persists, contact your switch service provider. 838 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 861
    . This is generally logged before download and after download of the firmware to store version information. Recommended Action No action is required. SULB-1037 Message HCL failed. Reboot the switch manually using the reboot command. However, it will disrupt the FC traffic. Message Type AUDIT
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 862
    , it will continue without updating the co-CPU firmware. Recommended Action After the firmware download completes, reboot the CP manually to bring up the co-CPU and run the firmwareDownload command again. If the problem persists, your switch service provider. SULB-1039 Message CP has completed
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 863
    Indicates that the firmwareActivate command has completed successfully and the switch firmware has been updated. Recommended Action No action is required. The firmwareActivate command has completed as expected. Run the firmwareShow command to verify the firmware versions. SULB-1043 Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 864
    that the firmwareDownload command to the secondary partition has completed successfully and the switch will come up with the updated firmware on reboot. Recommended Action No action is required. The switch will auto-reboot with the downloaded firmware. 842 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 865
    slot state has been detected as inconsistent during failover or recovery. Recommended Action For a bladed switch, execute the slotPowerOff and slotPowerOn commands to power cycle the blade. For a non-bladed switch, reboot or power cycle the switch. Fabric OS Message Reference 843 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 866
    not support N_Port ID Virtualization (NPIV) functionality, but the switch has some NPIV devices logged in to the fabric. Recommended Action Load a firmware version on a standby CP that supports NPIV functionality using the firmwareDownload command. 844 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 867
    the blade enabled with the port configuration that does not support port swap. Recommended Action Replace the blade with ports that support port swap. Then swap ports back to the port's default area. Refer to the Fabric OS Administrator's Guide for more information on port swapping. SWCH-1009
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 868
    configuration that had Trunk Area enabled previously. Recommended Action Disable Trunk Area on ports that had Trunk Area enabled previously. Refer to the Fabric OS Administrator's Guide for more information. SWCH-1011 Message HA out of sync: Stby CP (ver=) doesn't support
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 869
    has been detected by the software. This is usually an internal Fabric OS problem or due to file corruption. Recommended Action Reboot or power cycle the switch. If the message persists, execute the firmwareDownload command to update the firmware. Fabric OS Message Reference 847 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 870
    the requested area cannot be assigned because it is user bound to a different port. Remove the WWN-PID binding using the wwnaddress --unbind command or remove the port address binding using the portaddress --unbind command and then re-enable the port. 848 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 871
    that the standby control processor (CP) does not support dynamic area on the default switch. Recommended Action Load a firmware version on the standby CP that supports dynamic area on the default switch by using the firmwareDownload command. Fabric OS Message Reference 849 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 872
    ) does not support extended inter-switch link (XISL) while FICON Management Server (FMS) mode and Lossless are enabled. Recommended Action Load a firmware version on standby CP that supports both XISL use and FMS mode and Lossless at the same time by using the firmwareDownload command. SWCH-1024
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 873
    time configured on the default switch. Recommended Action To know the edge hold time configured for non 16 Gbps-capable FC ports, go to the default switch and execute the configShow command. SWCH-1026 Message HA state out of sync: Standby CP (ver = ) does not support auto
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 874
    . Message Type LOG Severity INFO Probable Cause Indicates that a terminated daemon is restarted by the system automatically. Recommended Action Execute the supportSave command to gather troubleshooting data. No further action is required. 852 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 875
    daemon is not restarted, either because a restart limit is reached or a restart action fails. Recommended Action Execute the supportSave command to gather troubleshooting data. Execute the reboot or haFailover command to recover the system. Fabric OS Message Reference 853 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 876
    executed the switchStart or switchReboot command. All services are brought back up after a temporary shutdown of the logical switch. Recommended Action No action is required if the switchStart command was executed intentionally. Because reinitializing a switch is a disruptive operation and can
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 877
    was a failure to read configuration data from the World Wide Name (WWN) card. Recommended Action Verify that the WWN card is present and operational not compatible with the control processor (CP) blade. Recommended Action Use the CP blade on a compatible chassis. Fabric OS Message Reference 855
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 878
    1007 Message PERMITTING USE OF INCOMPATIBLE CHASSIS FOR CP IN SLOT . DATA ERRORS MAY RESULT. Message Type LOG Severity WARNING Probable Cause Indicates an override Delete the /var/chassis_backplane_override file and reboot the CP. 856 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 879
    Severity INFO Probable Cause Indicates that the key acquisition for the pool or the container has begun or is complete. Recommended Action No action is required. Fabric OS Message Reference 857 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 880
    have been generated on the switch or the specified slot. The cause for the dump can be one of the following: • PANICDUMP: Generated by panic dump. • WATCHDOG EXPIRED: Generated by hardware watchdog expiration. • MANUAL: Generated manually by issuing the tracedump -n command. • TRIGGER: Triggered by
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 881
    ' '. Message Type LOG Severity INFO Probable Cause Indicates that a connectivity test to the FTP host has succeeded. This feature is enabled using the supportftp -t command. Recommended Action No action is required. Fabric OS Message Reference 859 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 882
    to verify that the current CP is standby and the other CP is active. If the message persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 860 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 883
    the trace dump files were manually transferred to the specified slot. Recommended Action No action is required. TRCE-1012 Message The system the command. If the blade is already enabled, execute the supportSave command and contact your switch service provider. Fabric OS Message Reference 861
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 884
    Cause Indicates that a trace dump has occurred on the switch or the specified slot, but the trace dump files were not automatically transferred from the switch because FIPS mode is enabled on the switch. Recommended Action No action is required. 862 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 885
    fabric, the IP address of a failed login is reported to the error log. TRCK-1003 Message Logout by user . Message Type LOG Severity INFO Probable Cause Indicates the track change feature recorded a successful logout. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 886
    memory, including a configuration download. This message is not generated for a configuration upload. All configuration changes occur through the parity data manager (PDM) server, so the PDMIPC is the only task possible. Recommended Action No action is required. Run the configShow command to view
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 887
    the clock server IP configured correctly, and the configured clock server is accessible to the switch and functional. If the principal or primary FCS does not support the feature, either choose a different switch for the role or reset the clock server to LOCL. Fabric OS Message Reference 865 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 888
    distributed from the principal or primary fabric configuration server (FCS) switch was changed to another configured clock server. This happens when the Network Time Protocol (NTP) query to the current active external clock server failed. 866 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 889
    Recommended Action No action is required. TS-1008 5 Fabric OS Message Reference 867 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 890
    routing protocol and the hardware configuration. The first port number displayed is what the hardware has configured and the second port number displayed is what the protocol is using. Recommended Action Run the switchDisable command and then the switchEnable command to reset the routing database
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 891
    CFG Severity INFO Probable Cause Indicates that Dynamic Load Sharing (DLS) option has been enabled on the switch. This will move existing routes to a new redundant path when this path becomes available. Recommended Action No action is required. Fabric OS Message Reference 869 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 892
    Sharing (DLS) option has been disabled on the switch. Recommended Action No action is required. UCST-1026 Message LossLess-DLS option has been enabled higher frame loss during fabric topology changes. Recommended Action No action is required. 870 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 893
    in the candidate list (domain ID list). Recommended Action No action is required. This error will end the current shortest path first (SPF) computation. UPTH-1002 Message Domain is unreachable because the enabled TI zone is not compatible with the fabric configuration. Message Type
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 894
    5 VDR-2001 VDR Messages VDR-2001 Message . Message Type LOG Severity WARNING Probable Cause Indicates that the Field-Programmable Gate Array (FPGA) parity error threshold exceeded. Recommended Action Power cycle the switch. 872 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 895
    file for the switch. Message Type LOG Severity ERROR Probable Cause Indicates that the configuration file is corrupted or accidently removed. Recommended Action Restart the switch and download the configuration using the configDownload command. Fabric OS Message Reference 873 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 896
    has been enabled for the first time on the switch or the configuration file was corrupted or accidently removed. Recommended Action Creating a new default configuration file. Execute the configDownload command to download any of your earlier configurations for the virtual PWWN feature. VS-1005
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 897
    Message Virtualization services failed to create timer. Message Type LOG Severity INFO Probable Cause Indicates failure in the virtualization service daemon (vsd) startup because vsd has failed to create a timer. Recommended Action No action is required. Fabric OS Message Reference 875 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 898
    server and weblinker process will be restarted due to configuration change. Message Type LOG Severity INFO Probable Cause Indicates the Hypertext Transfer Protocol (HTTP) server configuration has changed. Recommended Action No action is required. 876 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 899
    will be restarted due to change of IP Address. Message Type LOG Severity INFO Probable Cause Indicates the IP address of the switch changed and the Hypertext Transfer Protocol (HTTP) server is restarted. Recommended Action No action is required. Fabric OS Message Reference 877 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 900
    (HTTP) services. The problem often results from invalid configuration of Secure Sockets Layer (SSL) certificates, but there can be more than one reason for such a failure. Recommended Action Verify the certification file; there may be a mismatch involved. 878 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 901
    >/. Message Type LOG Severity ERROR Probable Cause Indicates a memory allocation failure. Recommended Action Contact your vendor's customer support for assistance. XTUN-1002 Message FCIP Tunnel Exchange timeout:I/T/L:
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 902
    vendor's customer support for assistance. XTUN-1004 Message FCIP Tunnel Exchange aborted:I/T/L://
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 903
    Number> DP has been cleared. Message Type LOG Severity INFO Probable Cause Indicates that a CLI command or supportSave operation freed the trace buffer back into the FTRACE free pool. Recommended Action No action is required. Fabric OS Message Reference 881 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 904
    event, contact your vendor's customer support for assistance. XTUN-1998 Message FTRACE buffer has been cleared. Message Type LOG Severity INFO Probable Cause Indicates that a CLI command or supportSave operation freed the trace buffer back into the FTRACE free pool
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 905
    Type LOG Severity INFO Probable Cause Indicates that the specified Fibre Channel over IP (FCIP) tunnel is up. Recommended Action No action is required. XTUN-2001 Message FCIP Tunnel DOWN (). Message Type LOG Severity ERROR Probable Cause Indicates that
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 906
    occurred. XTUN-2006 Message FCIP Tunnel CREATED (). Message Type LOG Severity INFO Probable Cause Indicates that the specified tunnel has been successfully created. Recommended Action No action is required. 884 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 907
    FCIP Tunnel Circuit CREATED (). Message Type LOG Severity INFO Probable Cause Indicates that the specified circuit has been successfully created. Recommended Action No action is required Action No action is required. XTUN-2010 Message SPD
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 908
    Message FCIP Tunnel Circuit DELETED (). Message Type LOG Severity INFO Probable Cause Indicates that the specified circuit has been administratively deleted. Recommended Action No action is required. 886 Fabric OS Message Reference 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 909
    Message FCIP Tunnel Circuit MODIFIED (). Message Type LOG Severity INFO Probable Cause Indicates that the specified circuit has been administratively modified. Recommended Action No action is required. Fabric OS Message Reference 887
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 910
    5 XTUN-2025 XTUN-2025 Message FCIP Tunnel Circuit MODATTR (). Message Type LOG value is modified within the specified circuit. Recommended Action No action is required. 888 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 911
    peer ports. Recommended Action Verify that compatible SFP transceivers are used on the peer ports, the ASIC) hardware that may degrade the data traffic. Recommended Action Reboot the system at the next maintenance window. If the problem persists, replace the blade. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 912
    that the port was re-initialized due to link reset failure. Recommended Action When this error is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. 890 Fabric OS Message Reference 53-1002749
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 913
    is observed persistently, power cycle the specified blade using the slotPowerOff and slotPowerOn commands. If the problem persists, replace the blade. ZEUS-1028 Message Detected excessive Link resets on the port in a second. Slot , Port (). Message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 914
    enforcement has changed to session-based hard zoning due to one of the following conditions: • The zone has a mix of WWN and domain,index (D,I) members. • The Source Identifier (S_ID) list of the hardware-enforced zoning exceeded the S_ID limit. 892 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 915
    are not supported in Fabric OS version 4.x or later. Even if the QuickLoop zoning configuration is enabled on the switch, it will not be supported. Recommended Action Edit the zone database to remove the QuickLoop zoning definition in the effective configuration. Fabric OS Message Reference 893
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 916
    set for each FA zone configuration. ZONE-1019 Message Transaction Commit switches. If the problem persists, execute the supportFtp command (as needed) to set up automatic FTP transfers; then execute the supportSave command and contact your switch service provider. 894 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 917
    the supportSave command and contact your switch service provider. ZONE-1024 Message . Message Type LOG Severity INFO Probable Cause Indicates that the cfgSave command has completed successfully. Recommended Action No action is required. Fabric OS Message Reference 895
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 918
    two zone databases. • Zone Config update Received: The fabric is in the process of updating the zone database. • Bad Zone Config: The new configuration is not viable. • Zoning Operation failed: A zoning operation failed. • Shell exited: The command shell has exited. • Unknown: An error was received
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 919
    supportSave command and contact your switch service provider. ZONE-1034 Message A new zone database file is created. Message Type LOG Severity INFO Probable Cause Indicates that a new zone database file has been created. Recommended Action No action is required. Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 920
    the Fabric OS cannot create the zone configuration file. Typically, the zone configuration is too large for the memory available on the switch. the Fabric OS cannot examine the zone configuration file. Typically, the zone configuration is too large for the memory available on the switch.
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 921
    the Fabric OS cannot read the merged zone configuration file. Typically, the zone configuration is too large for the memory available on the switch. the cable at the specified port are not faulty. Replace the SFP and the cable, if necessary. Fabric OS Message Reference 899 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 922
    action as defined by your enterprise security policy. ZONE-1045 Message The Default Zone access mode is already set to No Access. Message Type LOG Severity INFO Probable Cause Indicates that the Default Zone access mode is already set to No Access. 900 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 923
    that the default zoning mode for AD0 is set to No Access using the defzone --show command. If the default zoning mode is not set to No Access, execute the defzone --noaccess command and then execute the cfgsave command to commit the default zone mode change. Fabric OS Message Reference 901 53
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 924
    Default command. ZONE-1057 Message TI Zone has domain running pre FOS6.4.0 firmware. TI member (Domain , Index ) is not supported command. 902 Fabric OS Message Reference 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 925
    fabric topology and TI zone configuration may result in an unroutable condition or an unexpected routing behavior. Recommended Action Execute the zone --showTIerrors command on the specified switch to report the conflicting configuration failover-enabled inter-switch links (ISLs) to the specified
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 926
    object set was created and the specified zone object member or members were added to the zone object set. The zone object type variable can be an alias, zone member, zone, or zone configuration. The string "..." appears at the end of the zone object member list variable if the list was truncated in
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 927
    object type variable can be an alias, zone member, zone, or zone configuration. The string "..." appears at the end of the zone object member list variable if the list was truncated in the message. has been cleared from the transaction buffer. Fabric OS Message Reference 905 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 928
    , no action is required. If the event was configuration saved to MRAM. . Message Type AUDIT Class ZONE Severity INFO Probable Cause Indicates that the current zone configuration has been successfully saved to magnetoresistive random access memory (MRAM). 906 Fabric OS Message Reference
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 929
    the specified zone object has been expunged. Recommended Action Verify that the event was planned. If the event was planned, no action is required. If the event was not planned, take appropriate action as defined by your enterprise security policy. Fabric OS Message Reference 907 53-1002749-01
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 930
    Class FABRIC Severity INFO Probable Cause Indicates that the specified new Admin Domain (AD) object member or members have been added to an AD object set. The AD object set type variable can be an AD alias or AD member. The string "..." appears at the end of the AD object member list variable
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 931
    Message Type AUDIT Class FABRIC Severity INFO Probable Cause Indicates the specified Admin Domain (AD) has been created. The AD object set type variable can be an AD alias or AD member. The string "..." appears at the end of the AD object member list if the list was truncated in the message
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 932
    Message Event: , Status: success, Info: \"\" removed from \"\". Message Type AUDIT Class FABRIC Severity INFO Probable Cause Indicates that the specified Admin Domain (AD) member or members have been removed from the AD
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 933
    to flash. Message Type AUDIT Class FABRIC Severity INFO Probable Cause Indicates that the current Admin Domain (AD) configuration has been saved to flash memory. Recommended Action Verify that the event was planned. If the event was planned, no action is required. If the event was not planned
  • Dell Brocade 6510 | Fabric OS Message Reference v7.1.0 - Page 934
    . Message Type AUDIT Class FABRIC Severity INFO Probable Cause Indicates that the ad --exec command was executed in the specified Admin Domain (AD). Recommended Action Verify that the event was planned. If the event was planned, no action is required. If the event was not planned, take
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386
  • 387
  • 388
  • 389
  • 390
  • 391
  • 392
  • 393
  • 394
  • 395
  • 396
  • 397
  • 398
  • 399
  • 400
  • 401
  • 402
  • 403
  • 404
  • 405
  • 406
  • 407
  • 408
  • 409
  • 410
  • 411
  • 412
  • 413
  • 414
  • 415
  • 416
  • 417
  • 418
  • 419
  • 420
  • 421
  • 422
  • 423
  • 424
  • 425
  • 426
  • 427
  • 428
  • 429
  • 430
  • 431
  • 432
  • 433
  • 434
  • 435
  • 436
  • 437
  • 438
  • 439
  • 440
  • 441
  • 442
  • 443
  • 444
  • 445
  • 446
  • 447
  • 448
  • 449
  • 450
  • 451
  • 452
  • 453
  • 454
  • 455
  • 456
  • 457
  • 458
  • 459
  • 460
  • 461
  • 462
  • 463
  • 464
  • 465
  • 466
  • 467
  • 468
  • 469
  • 470
  • 471
  • 472
  • 473
  • 474
  • 475
  • 476
  • 477
  • 478
  • 479
  • 480
  • 481
  • 482
  • 483
  • 484
  • 485
  • 486
  • 487
  • 488
  • 489
  • 490
  • 491
  • 492
  • 493
  • 494
  • 495
  • 496
  • 497
  • 498
  • 499
  • 500
  • 501
  • 502
  • 503
  • 504
  • 505
  • 506
  • 507
  • 508
  • 509
  • 510
  • 511
  • 512
  • 513
  • 514
  • 515
  • 516
  • 517
  • 518
  • 519
  • 520
  • 521
  • 522
  • 523
  • 524
  • 525
  • 526
  • 527
  • 528
  • 529
  • 530
  • 531
  • 532
  • 533
  • 534
  • 535
  • 536
  • 537
  • 538
  • 539
  • 540
  • 541
  • 542
  • 543
  • 544
  • 545
  • 546
  • 547
  • 548
  • 549
  • 550
  • 551
  • 552
  • 553
  • 554
  • 555
  • 556
  • 557
  • 558
  • 559
  • 560
  • 561
  • 562
  • 563
  • 564
  • 565
  • 566
  • 567
  • 568
  • 569
  • 570
  • 571
  • 572
  • 573
  • 574
  • 575
  • 576
  • 577
  • 578
  • 579
  • 580
  • 581
  • 582
  • 583
  • 584
  • 585
  • 586
  • 587
  • 588
  • 589
  • 590
  • 591
  • 592
  • 593
  • 594
  • 595
  • 596
  • 597
  • 598
  • 599
  • 600
  • 601
  • 602
  • 603
  • 604
  • 605
  • 606
  • 607
  • 608
  • 609
  • 610
  • 611
  • 612
  • 613
  • 614
  • 615
  • 616
  • 617
  • 618
  • 619
  • 620
  • 621
  • 622
  • 623
  • 624
  • 625
  • 626
  • 627
  • 628
  • 629
  • 630
  • 631
  • 632
  • 633
  • 634
  • 635
  • 636
  • 637
  • 638
  • 639
  • 640
  • 641
  • 642
  • 643
  • 644
  • 645
  • 646
  • 647
  • 648
  • 649
  • 650
  • 651
  • 652
  • 653
  • 654
  • 655
  • 656
  • 657
  • 658
  • 659
  • 660
  • 661
  • 662
  • 663
  • 664
  • 665
  • 666
  • 667
  • 668
  • 669
  • 670
  • 671
  • 672
  • 673
  • 674
  • 675
  • 676
  • 677
  • 678
  • 679
  • 680
  • 681
  • 682
  • 683
  • 684
  • 685
  • 686
  • 687
  • 688
  • 689
  • 690
  • 691
  • 692
  • 693
  • 694
  • 695
  • 696
  • 697
  • 698
  • 699
  • 700
  • 701
  • 702
  • 703
  • 704
  • 705
  • 706
  • 707
  • 708
  • 709
  • 710
  • 711
  • 712
  • 713
  • 714
  • 715
  • 716
  • 717
  • 718
  • 719
  • 720
  • 721
  • 722
  • 723
  • 724
  • 725
  • 726
  • 727
  • 728
  • 729
  • 730
  • 731
  • 732
  • 733
  • 734
  • 735
  • 736
  • 737
  • 738
  • 739
  • 740
  • 741
  • 742
  • 743
  • 744
  • 745
  • 746
  • 747
  • 748
  • 749
  • 750
  • 751
  • 752
  • 753
  • 754
  • 755
  • 756
  • 757
  • 758
  • 759
  • 760
  • 761
  • 762
  • 763
  • 764
  • 765
  • 766
  • 767
  • 768
  • 769
  • 770
  • 771
  • 772
  • 773
  • 774
  • 775
  • 776
  • 777
  • 778
  • 779
  • 780
  • 781
  • 782
  • 783
  • 784
  • 785
  • 786
  • 787
  • 788
  • 789
  • 790
  • 791
  • 792
  • 793
  • 794
  • 795
  • 796
  • 797
  • 798
  • 799
  • 800
  • 801
  • 802
  • 803
  • 804
  • 805
  • 806
  • 807
  • 808
  • 809
  • 810
  • 811
  • 812
  • 813
  • 814
  • 815
  • 816
  • 817
  • 818
  • 819
  • 820
  • 821
  • 822
  • 823
  • 824
  • 825
  • 826
  • 827
  • 828
  • 829
  • 830
  • 831
  • 832
  • 833
  • 834
  • 835
  • 836
  • 837
  • 838
  • 839
  • 840
  • 841
  • 842
  • 843
  • 844
  • 845
  • 846
  • 847
  • 848
  • 849
  • 850
  • 851
  • 852
  • 853
  • 854
  • 855
  • 856
  • 857
  • 858
  • 859
  • 860
  • 861
  • 862
  • 863
  • 864
  • 865
  • 866
  • 867
  • 868
  • 869
  • 870
  • 871
  • 872
  • 873
  • 874
  • 875
  • 876
  • 877
  • 878
  • 879
  • 880
  • 881
  • 882
  • 883
  • 884
  • 885
  • 886
  • 887
  • 888
  • 889
  • 890
  • 891
  • 892
  • 893
  • 894
  • 895
  • 896
  • 897
  • 898
  • 899
  • 900
  • 901
  • 902
  • 903
  • 904
  • 905
  • 906
  • 907
  • 908
  • 909
  • 910
  • 911
  • 912
  • 913
  • 914
  • 915
  • 916
  • 917
  • 918
  • 919
  • 920
  • 921
  • 922
  • 923
  • 924
  • 925
  • 926
  • 927
  • 928
  • 929
  • 930
  • 931
  • 932
  • 933
  • 934
53-1002749-01
14 December 2012
®
Fabric OS
Message Reference
Supporting Fabric OS v7.1.0