D-Link DSN-3200 Light Fix
D-Link DSN-3200 - xStack Storage Area Network Array Hard Drive Manual
 |
UPC - 790069299759
View all D-Link DSN-3200 manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DSN-3200 manual content summary:
- D-Link DSN-3200 | Light Fix - Page 1
D-Link Systems, Inc.™ xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix (rev. 1) D-Link Systems, Inc. February 7, 2008 Page 1 - D-Link DSN-3200 | Light Fix - Page 2
xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix © 2008 D-Link Systems, Inc. All Rights Reserved D-Link Systems, Inc. are or may be trademarks or service marks, and are used to identify products or services, of their respective owners. D-Link Systems, Inc. 17595 Mount Herrmann - D-Link DSN-3200 | Light Fix - Page 3
: Step 1) Shut down the DSN-3200/3400 through your management GUI. Please follow the instructions in your xStack Storage User's Guide. Step 2) In order to minimize electrical shock risk, remove the three power cords from your DSN-3200/3400 unit's power supply. D-Link Systems, Inc. February 7, 2007 - D-Link DSN-3200 | Light Fix - Page 4
xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix Step 3) Remove the two right-most drives from the enclosure as need to continue to step 5. You may now reinsert the drive trays. Figure 2: Identifying the backplane revision number D-Link Systems, Inc. February 7, 2008 Page 4 - D-Link DSN-3200 | Light Fix - Page 5
xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix Step 5) Remove the top cover from the DSN-3200/3400. Located in the middle of the chassis is the chassis backplane as shown in figure 3. Figure 3: Identifying the chassis backplane Step 6) Located on the backplane are four 10- - D-Link DSN-3200 | Light Fix - Page 6
Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix Figure 5: A bare chassis backplane showing the four 10-position headers Step 7) If you see a jumper block installed on each of these four headers like that shown in Figure 6, then you will need to proceed to Section 2 for instructions - D-Link DSN-3200 | Light Fix - Page 7
xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix Figure 7: A resistor pack installed on a 10-position jumper. D-Link Systems, Inc. February 7, 2008 Page 7 - D-Link DSN-3200 | Light Fix - Page 8
through your management GUI. Please follow the instructions in your xStack Storage User's Guide. Step 2) In order to minimize electrical shock risk, remove the three power cords from your DSN-3200/3400 unit's power supply. Step 3) Please remove the cover from your DSN-3200/3400 to gain access to the - D-Link DSN-3200 | Light Fix - Page 9
xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix Step 6) For each 10-position header, you must remove the 4-position jumper block as seen in figure 6. You will then see an empty 10-position header like that shown in figure 9. The top-right pin is removed and will provide a guide for - D-Link DSN-3200 | Light Fix - Page 10
xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix Figure 11: The resistor pack: connector view Step 8) Carefully orient the resistor pack over the 10-position header, making sure the keyed hole matches the missing pin on the header. Press the resistor pack inwards until it is firmly - D-Link DSN-3200 | Light Fix - Page 11
xStack Storage DSN-3200 & DSN-3400 ECN - Drive Activity Light Fix Figure 13: Another view of an installed resistor pack Step 9) Install a resistor pack on the remaining three 10-position headers. Step 10) Install the two (2) Molex power connectors labeled CN4 and CN7. These were removed earlier as
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
 |
 |
D-Link Systems, Inc.
Page
1
February 7, 2008
D-Link Systems, Inc.™
xStack Storage DSN-3200 & DSN-3400
ECN – Drive Activity Light Fix
(rev. 1)