D-Link DGS-3130 Emulator

D-Link DGS-3130 Manual

Get D-Link DGS-3130 PDF manuals and user guides View all D-Link DGS-3130 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DGS-3130 manual content summary:

  • D-Link DGS-3130 | Emulator - Page 1
  • D-Link DGS-3130 | Emulator - Page 2
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Table of Contents Digital Diagnostics Monitoring (DDM) Commands 293 27. D-Link Discovery Protocol (DDP) Client Commands 303 28. DNS) Commands...306 29. DoS Prevention Commands...313 30. Dynamic ARP Inspection Commands ...317 31. Error
  • D-Link DGS-3130 | Emulator - Page 3
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 41. IP Utility Commands...458 42. IP-MAC-Port Binding (IMPB) Commands ...466 43. IPv6 Snooping Commands ...470 44. IPv6 Source Guard Commands ...475 45.
  • D-Link DGS-3130 | Emulator - Page 4
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 84. System File Management Commands ...840 85. System Log Commands...851 86. Time and Log Entries ...928 Appendix C - Trap Entries...959 Appendix D - RADIUS Attributes Assignment...971 Appendix E - IETF RADIUS Attributes Support ...974 iii
  • D-Link DGS-3130 | Emulator - Page 5
    troubleshooting the Switch. All the documents are available either from the CD, bundled with this switch, or from the D-Link website. Other documents related to this switch are:  DGS-3130 Series Hardware Installation Guide  DGS-3130 this manual are based on the DGS-3130-30TS switch in the DGS-3130
  • D-Link DGS-3130 | Emulator - Page 6
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide NOTICE: A notice indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A caution indicates a potential for property damage, personal injury, or death. Command Descriptions The
  • D-Link DGS-3130 | Emulator - Page 7
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide When a user logs in to the Switch, the privilege level of the user determines the command mode the user will enter after initially logging in.
  • D-Link DGS-3130 | Emulator - Page 8
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Privileged EXEC Mode at Advanced User can monitor all system information and change any system configuration settings mentioned in this Configuration Guide. The method to enter privileged EXEC mode at administrator level is to log into
  • D-Link DGS-3130 | Emulator - Page 9
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide VLAN Interface Configuration Mode VLAN interface configuration mode is one of the available interface modes and is used to configure the parameters of a VLAN interface.
  • D-Link DGS-3130 | Emulator - Page 10
    Guide DGS-3130-30TS Gigabit Ethernet Switch Command Line Interface Firmware: Build 1.00.001 Copyright(C) 2017 D-Link of the module plugged into the open module slot of the Switch. The DGS-3130 Series switch doesn't support any open modules slots, thus this parameter will always be zero for this
  • D-Link DGS-3130 | Emulator - Page 11
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show v Ambiguous command Switch# The following ^marker Switch# Editing Features The command line interface of this switch supports the following keyboard keystroke editing features. Keystroke Delete Backspace Left Arrow Right
  • D-Link DGS-3130 | Emulator - Page 12
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show running-config | begin # DEVICE # DEVICE configure terminal : 30689 bytes # DGS-3130-30TS Gigabit Ethernet Switch # Configuration # # Firmware: Build 1.00.001 # Copyright(C) 2017 D-Link Corporation. All rights
  • D-Link DGS-3130 | Emulator - Page 13
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 2. Basic CLI Commands 2-1 help This command is used to display a brief description of the help system. Use the help command in any command mode. help
  • D-Link DGS-3130 | Emulator - Page 14
    Switch#help DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The switch CLI provides advanced help feature. 1. Help is available when you are ready to enter a command argument (e.g. 'show ?') and want to know each possible
  • D-Link DGS-3130 | Emulator - Page 15
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline If the privileged level requires a password, enter it in the field provided. Only
  • D-Link DGS-3130 | Emulator - Page 16
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to change the privilege level of the active CLI login session to privilege level 1. Switch# show privilege Current privilege level
  • D-Link DGS-3130 | Emulator - Page 17
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline Use this command to change the login account. Three attempts are allowed to
  • D-Link DGS-3130 | Emulator - Page 18
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline For Console and Telnet access, when AAA is enabled, the line uses rules configured by the AAA module. When AAA is disabled, the
  • D-Link DGS-3130 | Emulator - Page 19
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# line console Switch(config-line)# login local Switch(config-line)# 2-7 logout This command is used to close an active terminal
  • D-Link DGS-3130 | Emulator - Page 20
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Executing this command will return access to the highest mode in the CLI hierarchy. Example This
  • D-Link DGS-3130 | Emulator - Page 21
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 2-10 show history This command is used to list or the Up Arrow key. The history buffer size is fixed at 20 commands. The function key instructions below display how to navigate the commands in the history buffer.  CTRL+P or the Up Arrow
  • D-Link DGS-3130 | Emulator - Page 22
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Reset Configuration Mode. Command Default Level how to enter the reset configuration mode, please contact the technical support personnel. After entering the reset configuration mode, use the password-recovery
  • D-Link DGS-3130 | Emulator - Page 23
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline If a specific type is not specified, all types of environment
  • D-Link DGS-3130 | Emulator - Page 24
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show unit [UNIT-ID] Parameters UNIT-ID (Optional 1 Model Descr 24*10/100/1000 + 2*10GBase-T + 4*10G SFP+ Model Name DGS-3130-30TS Unit ---- 1 Serial-Number DGS3130102030 Status --------- ok Up Time 0DT0H23M9S Unit ---- 1 1
  • D-Link DGS-3130 | Emulator - Page 25
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays the system's CPU utilization information in 5 second, 1
  • D-Link DGS-3130 | Emulator - Page 26
    Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the version information of the Switch. Switch#show version System MAC Address: F0-7D-68-36-30-00 Unit ID ------- 1 Module Name DGS-3130-30TS Versions H/W:A1 Bootloader:1.00.001 Runtime:1.01.001
  • D-Link DGS-3130 | Emulator - Page 27
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# snmp-server enable traps environment Switch(config)# 2-17 environment temperature threshold This command is used to configure the environment temperature
  • D-Link DGS-3130 | Emulator - Page 28
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show privilege Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to
  • D-Link DGS-3130 | Emulator - Page 29
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 3. 802.1X Commands 3-1 clear dot1x counters This command is used to clear 802.1X counters (diagnostics, statistics, and session statistics). clear dot1x counters {all | interface
  • D-Link DGS-3130 | Emulator - Page 30
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide in Specifies to enable in direction control for the port. Default By default, the auto. Forward PDU on port is disabled. Maximum request is 2 times. Server timer is 30 seconds. Supplicant timer is 30 seconds. Transmit interval is
  • D-Link DGS-3130 | Emulator - Page 31
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is used to reset all the IEEE 802.1X parameters on a
  • D-Link DGS-3130 | Emulator - Page 32
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to deny all access on ethernet 1/0/1. Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# dot1x port-control force-
  • D-Link DGS-3130 | Emulator - Page 33
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide dot1x initialize {interface INTERFACE-ID [, | -] | mac-address MAC-ADDRESS} Parameters interface INTERFACE-ID , - mac-address MACADDRESS Specifies the port on which the authenticator state machine
  • D-Link DGS-3130 | Emulator - Page 34
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is only available default command. Example This example shows how to configure ethernet 1/0/1 as an IEEE 802.1X PAE authenticator. 30
  • D-Link DGS-3130 | Emulator - Page 35
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# dot1x pae authenticator Switch(config-if)# This example shows how to disable IEEE 802.1X
  • D-Link DGS-3130 | Emulator - Page 36
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 3-10 dot1x system-auth-control This command is used to globally enable IEEE 802.1X authentication on the Switch. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 37
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide tx-period SECONDS Specifies the number of seconds that the Switch will wait for a response to an EAP-Request/Identity frame from the supplicant before retransmitting the request. The range is 1 to 65535 Default The server-timeout is 30
  • D-Link DGS-3130 | Emulator - Page 38
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Control Direction : Both Port Control : Auto Tx Period : 30 sec Supp Timeout : 30 sec Server Timeout : 30 sec Max-req : 2 times Forward PDU : Enabled Switch#
  • D-Link DGS-3130 | Emulator - Page 39
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of interfaces. No space is allowed before or after the hyphen. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode.
  • D-Link DGS-3130 | Emulator - Page 40
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show dot1x statistics [interface INTERFACE-ID [, | -]] Parameters interface INTERFACE-ID , - (Optional) Specifies to display the dot1x diagnostics on the specified interface or range of interfaces.
  • D-Link DGS-3130 | Emulator - Page 41
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show dot1x session-statistics [interface INTERFACE-ID [, | -]] Parameters interface INTERFACE-ID , - (Optional) Specifies to display the dot1x diagnostics on the specified interface or range of
  • D-Link DGS-3130 | Emulator - Page 42
    Parameters None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this feature is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline None. Example This example shows how
  • D-Link DGS-3130 | Emulator - Page 43
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 4. Access Control List (ACL) Commands 4-1 access- increment (step) value is 5 and the beginning sequence number is 20, the subsequent sequence numbers are 25, 30, 35, 40, and so on. The range of valid values is from 1 to 32. Default The
  • D-Link DGS-3130 | Emulator - Page 44
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# show access-list ip R&D Extended IP access list R&D(ID: 3552) 10 permit tcp any 10.20.0.0 0.0.255.255 20 permit tcp any host 10.100.1.2 30 permit icmp any any Switch(config)#ip access-list
  • D-Link DGS-3130 | Emulator - Page 45
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline One sub-map has only one action. The action configured later overwrites the previous action. A VLAN access map
  • D-Link DGS-3130 | Emulator - Page 46
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline If expert access group is already configured on the interface, the command applied later will overwrite the previous
  • D-Link DGS-3130 | Emulator - Page 47
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to create an extended expert ACL. Switch#configure terminal Switch(config)#expert access-list extended exp_acl Switch(config-exp-nacl)# 4-5
  • D-Link DGS-3130 | Emulator - Page 48
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#configure terminal Switch(config)#interface ethernet 1/0/2 Switch(config-if)#ip access-group Strict-Control The remaining applicable IP related access entries are 1792, remaining
  • D-Link DGS-3130 | Emulator - Page 49
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 4-7 ipv6 access-group This command is used to specify the IPv6 access list to be applied to an interface. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 50
    Parameters extended NAME DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies that the IPv6 (config)# ipv6 access-list ip6-std-control Switch(config-ipv6-acl)# permit any fe80::101:1/54 Switch(config-ipv6-acl)# 4-9 mac access-group This command is used to specify a MAC
  • D-Link DGS-3130 | Emulator - Page 51
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide out (Optional) Specifies that the MAC access list will be applied to check in the egress direction. Default None. Command Mode Interface Configuration Mode. Command
  • D-Link DGS-3130 | Emulator - Page 52
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to enter the MAC Access-list Configuration mode, and use the permit or deny command
  • D-Link DGS-3130 | Emulator - Page 53
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# vlan access-map vlan-map 20 Switch(config-access-map)# match ip address sp1 Switch(config-access-map)# end Switch#
  • D-Link DGS-3130 | Emulator - Page 54
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# vlan access-map vlan-map 20 Switch(config-access-map)# match ipv6 address sp1 Switch(config-access-map)# end Switch#
  • D-Link DGS-3130 | Emulator - Page 55
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# vlan access-map vlan-map 30 Switch(config-access-map)# match mac address ext_mac Switch(config-access-map)# end Switch# show vlan access-map VLAN access-map vlan-map 20 match
  • D-Link DGS-3130 | Emulator - Page 56
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide inner INNER-COS vlan OUTER-VLAN as specified by a number from 0 to 7. (Optional) Specifies that packets can be filtered by type of service level, as specified by a number from 0 to 15. (Optional) Specifies the matching DSCP code in the
  • D-Link DGS-3130 | Emulator - Page 57
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide parameter-problem, port-unreachable, reassembly-timeout, redirect, renumcommand based on the new sequence setting of the specified access list. When you manually assign the sequence number, it is better to have a reserved interval for
  • D-Link DGS-3130 | Emulator - Page 58
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide [SEQUENCE-NUMBER] {permit | deny} icmp { default - 000000, ef - 101110. (Optional) Specifies that packets can be filtered by type of service level, as specified by a number from 0 to 15. (Optional) Specifies to match if from 0 to 255. 54
  • D-Link DGS-3130 | Emulator - Page 59
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ICMP-TYPE ICMP optionmissing,packet-fragment,parameter-problem,port-unreachable,precedencecutoff, the new sequence setting of the specified access list. When you manually assign the sequence number, it is better to have a reserved
  • D-Link DGS-3130 | Emulator - Page 60
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to create two entries for an IP standard access list, named "std-acl". These entries are: permit IP packets destined for
  • D-Link DGS-3130 | Emulator - Page 61
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide tcp, udp, icmp dscp VALUE traffic-class VALUE lt PORT ns, next-header, no-admin, noroute, packet-too-big, parameter-option, parameter-problem, port-unreachable, reassembly-timeout, redirect, renum-command, renum-result, renum-seqnumber,
  • D-Link DGS-3130 | Emulator - Page 62
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The user can use the access-list resequence assigned a number based on the new sequence setting of the specified access list. When you manually assign the sequence number, it is better to have a reserved interval for future lower sequence
  • D-Link DGS-3130 | Emulator - Page 63
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide DST-MAC-ADDR DSTMAC-WILDCARD ethernet-type TYPE will be assigned sequence based new sequence setting of the specified access list. When you manually assign the sequence number, it is better to have a reserved interval for future lower
  • D-Link DGS-3130 | Emulator - Page 64
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 4-18 show access-group This command is used to display access group information for interface(s). show access-group [interface INTERFACE-ID] Parameters interface INTERFACE-ID (
  • D-Link DGS-3130 | Emulator - Page 65
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any 85201 packets) 20 permit tcp any host 10.100.1.2 (Ing: 6532 packets Egr: 0 packets) 30 permit icmp any any (Ing: 8758 packets Egr: 4214 packets) Counter enable on following port(s): Ingress
  • D-Link DGS-3130 | Emulator - Page 66
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 4-20 show vlan access-map This command is used to display the VLAN access-map configuration information. show vlan access-map [MAP-NAME] Parameters MAP-
  • D-Link DGS-3130 | Emulator - Page 67
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show vlan access-map VLAN access-map vlan-map 10 match ip access list: stp_ip1(ID: 1888) action: forward Counter enable on VLAN(s): 1-2 match
  • D-Link DGS-3130 | Emulator - Page 68
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show vlan filter VLAN Map aa to VLAN(s). A sequence number will be assigned automatically if the user does not assign it manually, and the automatically assigned sequence number starts from 10, and increase 10 per new entry.
  • D-Link DGS-3130 | Emulator - Page 69
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to create a VLAN access map. Switch# configure terminal Switch(config)# vlan access-map vlan-map 20 Switch(config-access-map)# 4-
  • D-Link DGS-3130 | Emulator - Page 70
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 5. Access Management Commands 5-1 access class This command is used to specify an access list to restrict the access via a line. Use the no form of
  • D-Link DGS-3130 | Emulator - Page 71
    Parameters c MESSAGE DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the separator of the login banner message, for example a pound sign (#). The delimiting character is not allowed in the login banner message. Specifies the
  • D-Link DGS-3130 | Emulator - Page 72
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide prompt STRING no prompt Parameters STRING Specifies a string to define the customized prompt. The prompt will be based on the specified characters or the following
  • D-Link DGS-3130 | Emulator - Page 73
    0 7 15 PASSWORD DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies the password in clear, plain text. The password length is between 1 and 32 characters and can contain embedded spaces. It is casesensitive. If
  • D-Link DGS-3130 | Emulator - Page 74
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is enabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline This command enables the HTTP server
  • D-Link DGS-3130 | Emulator - Page 75
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip http config)# ip http access-class http-filter Switch(config)# 5-8 ip http service-port This command is used to specify the HTTP service port. Use the no form of this command to revert to the
  • D-Link DGS-3130 | Emulator - Page 76
    Parameters TCP-PORT DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the TCP port number. TCP ports the HTTP TCP port number to 8080. Switch# configure terminal Switch(config)# ip http service-port 8080 Switch(config)# 5-9 ip http timeout-policy idle This command is used to
  • D-Link DGS-3130 | Emulator - Page 77
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the terminal Switch(config)# ip telnet server Switch(config)# 5-11 ip telnet service port This command is used to specify the service port for Telnet. Use the no form of this command to revert
  • D-Link DGS-3130 | Emulator - Page 78
    Parameters TCP-PORT DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the TCP port number. TCP ports are This example shows how to change the Telnet service port number to 3000. Switch# configure terminal Switch(config)# ip telnet service-port 3000 Switch(config)# 5-12 ip
  • D-Link DGS-3130 | Emulator - Page 79
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to specify )# line ssh Switch(config-line)# access-class vty-filter Switch(config-line)# 5-14 service password-recovery This command is used to enable or disable the backdoor password recovery feature.
  • D-Link DGS-3130 | Emulator - Page 80
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide service password-recovery no service password-recovery Parameters None. Default By default, this option is enabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this
  • D-Link DGS-3130 | Emulator - Page 81
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The user account configuration information is stored in the running configuration file and can be applied to the system later. If the service password-encryption command is enabled, the password will be stored in the
  • D-Link DGS-3130 | Emulator - Page 82
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show terminal Terminal Settings: Length: 24 lines Width: 80 columns Default Length: 24 lines Default Width: 80 columns Baud rate: 9600 bps Switch# 5-17
  • D-Link DGS-3130 | Emulator - Page 83
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ip http secure-server Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This
  • D-Link DGS-3130 | Emulator - Page 84
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command displays information Total Entries: 3 Switch# 5-20 telnet This command is used to login another device that supports Telnet. telnet [IP-ADDRESS | IPV6-ADDRESS] [TCP-PORT] Parameters IP-ADDRESS IPV6-ADDRESS
  • D-Link DGS-3130 | Emulator - Page 85
    not open a connection to host on server port 23. Switch# telnet 10.90.90.91 3500 DGS-3130-30TS Gigabit Ethernet Switch Command Line Interface Firmware: Build 1.00.001 Copyright(C) 2017 D-Link Corporation. All rights reserved. Password required, but none set Switch# 5-21 terminal length The command
  • D-Link DGS-3130 | Emulator - Page 86
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this value is 24. . Valid entries are from 0 to 512. The default is 24 lines. A selection of 0's instructs the Switch to scroll continuously (no pausing). Output from a single command that overflows a single display
  • D-Link DGS-3130 | Emulator - Page 87
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the terminal connection speed. Some baud rates available on the devices connected to the port might not be supported on
  • D-Link DGS-3130 | Emulator - Page 88
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# line console Switch(config-line)# session-timeout 0 Switch(config-line)# 5-24 terminal width The command is used to set the
  • D-Link DGS-3130 | Emulator - Page 89
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show terminal Length: 24 lines Width: 80 columns Default Length: 24 lines Default Width: 80 columns Baud rate: 9600 Switch# terminal width 120 Switch#
  • D-Link DGS-3130 | Emulator - Page 90
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline This command or in the plain-text form. If it is in the plain-text form, but the service password encryption is enabled, then the password will be converted to the encrypted form. If the
  • D-Link DGS-3130 | Emulator - Page 91
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Line Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to create a new user password. Only one password can
  • D-Link DGS-3130 | Emulator - Page 92
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 6. ARP Spoofing Prevention Commands 6-1 ip arp spoofing-prevention This command is used to configure an ARP Spoofing Prevention (ASP) entry of the gateway used for
  • D-Link DGS-3130 | Emulator - Page 93
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 6-2 show ip arp spoofing-prevention This command is used to display the configuration of ARP spoofing prevention. show ip arp spoofing-prevention Parameters None. Default
  • D-Link DGS-3130 | Emulator - Page 94
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 7. Asymmetric VLAN Commands 7-1 asymmetric-vlan This command is used to enable the asymmetric VLAN function. Use the no form of this command to disable the
  • D-Link DGS-3130 | Emulator - Page 95
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 8. Authentication, Authorization, and Accounting (AAA) Commands 8-1 aaa accounting commands This command is used to configure the accounting method list used for all commands at the
  • D-Link DGS-3130 | Emulator - Page 96
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 8-2 aaa accounting exec This command is used to configure the method list used for EXEC accounting for a specific line. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 97
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide network start-stop default METHOD1 [METHOD2...] Specifies to perform accounting of network related service requests. Specifies to send accounting messages at both the start time and the end time of access. Users are allowed
  • D-Link DGS-3130 | Emulator - Page 98
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide system start-stop default METHOD1 [METHOD2...] Specifies to perform accounting for system-level events. Specifies to send accounting messages at both the start time and
  • D-Link DGS-3130 | Emulator - Page 99
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide METHOD1 [METHOD2...] Specifies the list of methods that the authentication algorithm tries in the given sequence. Enter at least one method or enter up to
  • D-Link DGS-3130 | Emulator - Page 100
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide group radius - Specifies to use the servers defined by the RADIUS server host command. group GROUP-NAME - Specifies to use the server groups defined by
  • D-Link DGS-3130 | Emulator - Page 101
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to configure the default authentication method list for IGMP authentication. Example This example shows how to set the default methods
  • D-Link DGS-3130 | Emulator - Page 102
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The login authentication authenticates the login user name and password, and also assigns the privilege level to the user based on the database. A method list
  • D-Link DGS-3130 | Emulator - Page 103
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to configure the default authentication method list for MAC authentication. Initially, the default method list is not configured. The authentication
  • D-Link DGS-3130 | Emulator - Page 104
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#configure terminal Switch(config)# aaa authentication web-auth default group radius Switch(config)# 8-11 aaa group server radius This command is used to enter
  • D-Link DGS-3130 | Emulator - Page 105
    Parameters GROUP-NAME DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the name of the server group. This name can be up to 32 characters long. The syntax is a general string that does not allow
  • D-Link DGS-3130 | Emulator - Page 106
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The user should use the aaa new-model command to enable AAA before the authentication and accounting via the AAA method lists take
  • D-Link DGS-3130 | Emulator - Page 107
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# aaa accounting commands 15 cmd-15 start-stop group tacacs+ Switch(config)# line console Switch(config-line)# accounting commands 15
  • D-Link DGS-3130 | Emulator - Page 108
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide clear aaa counters servers {all | radius {IP-ADDRESS| IPV6-ADDRESS | all} | tacacs {IP-ADDRESS | all} | sg NAME} Parameters all radius IP-ADDRESS radius IPV6-ADDRESS
  • D-Link DGS-3130 | Emulator - Page 109
    Parameters INTERFACE-ID DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the interface whose IP address will be used as the source IP address for sending RADIUS packets. Default The IP address of the closest
  • D-Link DGS-3130 | Emulator - Page 110
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline This command can be used to specify the interface whose IP address will be used as the source
  • D-Link DGS-3130 | Emulator - Page 111
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to set VLAN 100, whose IPv6 address will be used as the source IPv6 address, for sending RADIUS packets. Switch#
  • D-Link DGS-3130 | Emulator - Page 112
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide login authentication {default | METHOD-LIST} no login authentication Parameters default METHOD-LIST Specifies to authenticate based on the default method list. Specifies the name of
  • D-Link DGS-3130 | Emulator - Page 113
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline This command can be used to improve the authentication processing time by setting
  • D-Link DGS-3130 | Emulator - Page 114
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, no server is configured. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to create RADIUS
  • D-Link DGS-3130 | Emulator - Page 115
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide list for authentication, or accounting via the aaa authentication and aaa accounting commands. Use the radiusserver host command to create a server host entry. A host entry
  • D-Link DGS-3130 | Emulator - Page 116
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#configure terminal Switch(config)# tacacs-server host 172.19.10.100 port 1500 timeout 8 key ABCDE Switch(config)# tacacs-server host 172.19.122.3
  • D-Link DGS-3130 | Emulator - Page 117
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IP-ADDRESS IPV6-ADDRESS port PORT-NUMBER timeout SECONDS 0 7 key KEY-STRING Specifies the IPv4 address of the TACACS+ server. Specifies the IPv6 address of
  • D-Link DGS-3130 | Emulator - Page 118
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display statistics counters related to servers.
  • D-Link DGS-3130 | Emulator - Page 119
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Retransmissions Malformed Responses Bad Authenticators Pending Requests Timeouts Unknown Types Packets Dropped The number of RADIUS Request packets retransmitted to this RADIUS server. Retransmissions include
  • D-Link DGS-3130 | Emulator - Page 120
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show tacacs statistics TACACS+ Server: 172.19.192.80/49, State is UP Socket Opens: 0 Socket Closes: 0 Total Packets Sent: 0 Total Packets Recv: 0 Reference
  • D-Link DGS-3130 | Emulator - Page 121
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 9. Basic IPv4 Commands 9-1 arp This command is used to add 12. Usage Guideline The ARP table keeps the network layer IP address to local data-link MAC address association. The association is kept so that the addresses will not have to be
  • D-Link DGS-3130 | Emulator - Page 122
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default The default value is 240 minutes. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Used to set the ARP aging
  • D-Link DGS-3130 | Emulator - Page 123
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to remove all The IPv4 address of an interface can be either manually assigned by the user or dynamically assigned by the DHCP server. For manual assignment, the user can assign multiple networks to a
  • D-Link DGS-3130 | Emulator - Page 124
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface vlan 100 Switch(config-if)# ip address 10.108.1.27 255.255.255.0 Switch(config-if)# ip address 192.
  • D-Link DGS-3130 | Emulator - Page 125
    Parameters None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to enable the
  • D-Link DGS-3130 | Emulator - Page 126
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable IP ARP elevation. Switch# configure terminal Switch(config)# ip arp elevation Switch(config)# 9-8 ip mtu This command is
  • D-Link DGS-3130 | Emulator - Page 127
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IP-ADDRESS [MASK] INTERFACE-ID HARDWARE-ADDRESS (Optional) Specifies to display a specific entry or entries that belong to a specific network. (Optional) Specifies to display ARP
  • D-Link DGS-3130 | Emulator - Page 128
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any display the ARP aging time. Switch# show arp timeout Interface Timeout (minutes) vlan 100 30 vlan 200 40 Total Entries: 2 Switch# 9-11 show ip interface This command is
  • D-Link DGS-3130 | Emulator - Page 129
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the brief information of the IP interface. Switch#show ip interface brief Interface ---------vlan 1 mgmt_ipif IP Address 10.90.90.90 192.168.0.1 Link is 192.168.1.1/24 (Manual) Total Entries: 1
  • D-Link DGS-3130 | Emulator - Page 130
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the
  • D-Link DGS-3130 | Emulator - Page 131
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 10. Basic IPv6 Commands 10-1 clear ipv6 of this command to delete a manually configured IPv6 address. ipv6 address {IPV6-ADDRESS/PREFIX-LENGTH | PREFIX-NAME SUB-BITS/PREFIX-LENGTH | IPV6ADDRESS link-local} no ipv6 address {IPV6-
  • D-Link DGS-3130 | Emulator - Page 132
    PREFIX-NAME SUB-BITS link-local DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the name of the prefix multiple IPv6 addresses assigned using a variety of mechanisms, including manual configuration, stateless address configuration, and stateful address configuration. When
  • D-Link DGS-3130 | Emulator - Page 133
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface vlan 2 Switch(config-if)# no ipv6 address dhcp-prefix 0:0:0:2::3/64 10-3 ipv6 address eui-64 This command is used
  • D-Link DGS-3130 | Emulator - Page 134
    Parameters rapid-commit DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to use a two-message exchange instead of the standard four-message exchange between the Requesting Router (RR) and the Delegating Router (DR) to obtain
  • D-Link DGS-3130 | Emulator - Page 135
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Guideline When the IPv6 address is explicitly configured on the interface, the IPv6 link-local address is automatically generated and the IPv6 processing is started. When the
  • D-Link DGS-3130 | Emulator - Page 136
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable IPv6 on interface VLAN 1, which has no IPv6 address explicitly configured. Switch# configure terminal Switch(config)# interface vlan 1
  • D-Link DGS-3130 | Emulator - Page 137
    Parameters BYTES DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to set the IPv6 MTU value. The range is 1280 to 65534 bytes. Default By default, the IPv6 MTU value is 1500 bytes. Command
  • D-Link DGS-3130 | Emulator - Page 138
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level 12. Usage Guideline By setting the other configuration flag on, the router instructs the connected hosts to use a stateful configuration protocol to obtain auto-
  • D-Link DGS-3130 | Emulator - Page 139
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide the default valid lifetime value is 2592000 seconds (30 days). (Optional) Specifies the preferred lifetime in one of the following combinations:  Combination 1:Both the off-link and no-autoconfig options are not specified. o The prefix is
  • D-Link DGS-3130 | Emulator - Page 140
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure an IPv6 prefix of 3ffe:501:ffff:100::/64 with a valid lifetime of 30000 seconds and the preferred
  • D-Link DGS-3130 | Emulator - Page 141
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ipv6 nd ra lifetime SECONDS no ipv6 nd ra Configuration Mode. Command Default Level Level: 12. Usage Guideline The lifetime value in RA instructs the received host the lifetime value for taking the router as the default router. Example
  • D-Link DGS-3130 | Emulator - Page 142
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use the ipv6 nd suppress-ra command to disable the sending of RA messages on the interface. Use
  • D-Link DGS-3130 | Emulator - Page 143
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface vlan 1 Switch (config-if)# ipv6 nd reachable-time 3600000 Switch (config-if)# 10-16 ipv6 nd ns-interval This
  • D-Link DGS-3130 | Emulator - Page 144
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IPV6-ADDRESS INTERFACE-ID MAC-ADDRESS Specifies the IPv6 address of the IPv6 neighbor cache entry. Specifies the interface for creating the static IPv6 neighbor
  • D-Link DGS-3130 | Emulator - Page 145
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display information of IPv6 general prefixes. Example This example shows how to display all IPv6
  • D-Link DGS-3130 | Emulator - Page 146
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display IPv6 interface information. Switch# show ipv6 interface vlan 2 vlan 2 is up, Link status is down IPv6 is enabled, link-local address: FE80::201:1FF:FE02:305 Global unicast address: 200::2/64 (
  • D-Link DGS-3130 | Emulator - Page 147
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the IPv6 neighbor cache entry.
  • D-Link DGS-3130 | Emulator - Page 148
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 11. BPDU Protection Commands 11-1 spanning-tree bpdu-protection (global) This command is used to enable the BPDU protection function globally. Use the no form
  • D-Link DGS-3130 | Emulator - Page 149
    Parameters drop block shutdown DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to drop all received BPDU packets when the interface enters the attacked state. Specifies to drop all packets (include BPDU and normal packets) when
  • D-Link DGS-3130 | Emulator - Page 150
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display BPDU protection information. If no interface ID is specified, all interfaces'
  • D-Link DGS-3130 | Emulator - Page 151
    Status DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Indicates if the interface is under the protection state. 11-4 snmp-server enable traps stp-bpdu-protection This command is used to enable the sending
  • D-Link DGS-3130 | Emulator - Page 152
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 12. Cable Diagnostics Commands 12-1 test configuration. Cable Diagnostics can help users to detect whether the copper Ethernet port has connectivity problems. Use the test cable-diagnostics command to start the test. The copper port can
  • D-Link DGS-3130 | Emulator - Page 153
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide interface INTERFACE-ID , - (Optional) Specifies the interface's ID. The acceptable interface will be a physical port. (Optional) Specifies a series of interfaces, or separate a range of interfaces
  • D-Link DGS-3130 | Emulator - Page 154
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 12-3 clear cable-diagnostics This command is used to clear the test results for the cable diagnostics. clear cable-diagnostics {all | interface INTERFACE-ID [, | -]} Parameters
  • D-Link DGS-3130 | Emulator - Page 155
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 13. Command Logging Commands 13-1 command logging enable This command is used to enable the command logging function. Use the no form of this command
  • D-Link DGS-3130 | Emulator - Page 156
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 14. CPU Access Control List (ACL) Commands 14-1 soft-acl filter-map This command is used to create or modify a software ACL filter map. This
  • D-Link DGS-3130 | Emulator - Page 157
    NAME DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the ACL access list name to be match. Default None. Command Mode Software ACL Filter Map Configuration Mode. Command Default Level Level: 12. Usage
  • D-Link DGS-3130 | Emulator - Page 158
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of interfaces. No space is allowed before or after the hyphen. all Specifies that in the no form of this command, to
  • D-Link DGS-3130 | Emulator - Page 159
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 14-4 show soft-acl This command is used to display the information of software ACL filter maps. show soft-acl filter-map [NAME] Parameters NAME (
  • D-Link DGS-3130 | Emulator - Page 160
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 15. Debug Commands 15-1 debug enable This command is used to enable the debug message output option. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 161
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default The default debug output is buffer. Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to set a specified
  • D-Link DGS-3130 | Emulator - Page 162
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#configure terminal Switch(config)#debug reboot on- . error-log: Specifies to copy the error log information. tech-support: Specifies to copy the technical support information. Specifies the IPv4 or IPv6 address of the TFTP server.
  • D-Link DGS-3130 | Emulator - Page 163
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide debug clear buffer Parameters None. Default None. Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to clear the
  • D-Link DGS-3130 | Emulator - Page 164
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# debug clear error-log Switch# 15-7 debug buffer utilization Debug buffer is allocated from system memory Total size is 2M Utilization is 30% Switch# 15-8 debug show output This command is used to display the debug status and
  • D-Link DGS-3130 | Emulator - Page 165
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide debug show output Parameters None. Default None. Command Mode Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command
  • D-Link DGS-3130 | Emulator - Page 166
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline Use this command to ->802B4498 ->802B4B00 ->802BD140 ->802BCB08 Total Log : 2 Switch# 15-10 debug show tech-support This command is used to display the information required by technical
  • D-Link DGS-3130 | Emulator - Page 167
    troubleshoot or analyze a problem. Example This example shows how to display technical support information of all the modules. Switch#debug show tech-support # DGS-3130-30TS Gigabit Ethernet Switch # Technical Support Information # # Firmware: Build 1.00.001 # Copyright(C) 2017 D-Link
  • D-Link DGS-3130 | Emulator - Page 168
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 15-11 debug show cpu utilization This command is used to display the total CPU utilization and the CPU utilization per process. debug show cpu
  • D-Link DGS-3130 | Emulator - Page 169
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 16. DHCP Auto-Configuration Commands 16-1 autoconfig enable This command is used to enable the auto-configuration function. Use the no form of this command
  • D-Link DGS-3130 | Emulator - Page 170
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display the status of the
  • D-Link DGS-3130 | Emulator - Page 171
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 17. DHCP Client Commands 17-1 ip dhcp client class-id This command is used to specify the vendor class identifier used as the value of
  • D-Link DGS-3130 | Emulator - Page 172
    Parameters INTERFACE-ID DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the VLAN interface, whose hexadecimal MAC address will be used as the client ID to be sent with the discover message. Default The MAC
  • D-Link DGS-3130 | Emulator - Page 173
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to specify the host name string (Option 12) to be sent with the DHCP discover
  • D-Link DGS-3130 | Emulator - Page 174
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface vlan 100 Switch(config-if)# ip address dhcp Switch(config-if)# ip dhcp client lease 5 Switch(config-if)# 170
  • D-Link DGS-3130 | Emulator - Page 175
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 18. DHCP Relay Commands 18-1 ip dhcp pool (DHCP Relay) This command is used to configure a DHCP relay pool on a DHCP relay agent and enter
  • D-Link DGS-3130 | Emulator - Page 176
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip dhcp relay information check no ip dhcp relay information check Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode.
  • D-Link DGS-3130 | Emulator - Page 177
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command only takes effect when the DHCP service is enabled. The ip dhcp relay information check command and the ip dhcp relay information
  • D-Link DGS-3130 | Emulator - Page 178
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command takes effect when the service dhcp command is enabled. Default Level Level: 12. Usage Guideline This command takes effect when the service dhcp command is enabled. Example This example shows how to enable the
  • D-Link DGS-3130 | Emulator - Page 179
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip dhcp Default Level Level: 12. Usage Guideline The command only takes effect when the DHCP service is enabled. Use this command to configure the global policy for the insertion of Option
  • D-Link DGS-3130 | Emulator - Page 180
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip dhcp relay information policy-action {drop | keep | Default Level Level: 12. Usage Guideline The command only takes effect when the DHCP service is enabled. Use this command to configure the interface policy for the insertion of Option
  • D-Link DGS-3130 | Emulator - Page 181
    SENTENCE vendor2 expert-udf DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide | 2 | 8 | 0 | 6 | MAC Address | | 1 byte | 1 byte | 1 byte | 1 byte | 6 bytes | Specifies to use a user-defined string as the remote ID. Space characters are allowed in the string. The
  • D-Link DGS-3130 | Emulator - Page 182
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to use vendor2 as the remote ID. Switch# configure terminal Switch(config)# ip dhcp relay information option Switch(config)# ip
  • D-Link DGS-3130 | Emulator - Page 183
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 18-10 ip dhcp relay information option format circuit-id This command is used to configure the DHCP information circuit ID sub-option. Use the
  • D-Link DGS-3130 | Emulator - Page 184
    expert-udf DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide b. Length. c. Circuit ID's sub-option's first tag: This should be 0. d. First tag's length: This should be 6 e. VLAN ID. f. Slot ID: For a stand-alone switch, this
  • D-Link DGS-3130 | Emulator - Page 185
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip dhcp relay information option Switch(config)# ip dhcp relay information option format circuit-id string abcd Switch(config)# 18-
  • D-Link DGS-3130 | Emulator - Page 186
    Parameters None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline When IP DHCP relay information trust
  • D-Link DGS-3130 | Emulator - Page 187
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline When IP DHCP relay information is trusted on an interface, the arriving packets with the GIADDR of 0 (this
  • D-Link DGS-3130 | Emulator - Page 188
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The local relay relays the DHCP message to all local VLAN member ports based on the relay option setting. The local relay does
  • D-Link DGS-3130 | Emulator - Page 189
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how a DHCP relay pool "pool1" is created. In the relay pool, the subnet 172.19.10.0/255.255.255.0 is specified
  • D-Link DGS-3130 | Emulator - Page 190
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how a DHCP relay pool "pool2" is created. In the relay pool, the subnet 172.19.18.0.0/255.255.255.0 is specified
  • D-Link DGS-3130 | Emulator - Page 191
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip dhcp class Service-A Switch(config- source 172.19.18.0 255.255.255.0 Switch(config-dhcp-pool)# class Service-A Switch(config-dhcp-pool-class)# relay target 10.2.1.2 Switch(config-dhcp-pool-
  • D-Link DGS-3130 | Emulator - Page 192
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip dhcp relay information trusted-sources All interfaces are trusted source of relay agent information option Switch# 18-19 show ip dhcp relay
  • D-Link DGS-3130 | Emulator - Page 193
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ip dhcp relay information option format-type eth1/0/1 Remote ID vendor string: string1 eth1/0/2 Circuit ID vendor string: string1 eth1/0/3 Remote ID vendor
  • D-Link DGS-3130 | Emulator - Page 194
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip dhcp relay information option-insert Interface Option-Insert vlan 1 Enabled vlan 2 Disabled vlan 3 Not Configured Total Entries: 3 Switch# 18-21 show ip
  • D-Link DGS-3130 | Emulator - Page 195
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip dhcp relay information policy-action Interface Policy vlan 1 Keep vlan 2 Drop vlan 3 Replace vlan 4 Not configured Total Entries: 3 Switch# 18-22 ip
  • D-Link DGS-3130 | Emulator - Page 196
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 18-23 ip dhcp relay information profile Profile Configure mode to define the profile "remote_id". Switch#configure terminal Switch(config)#service dhcp Switch(config)#ip dhcp relay information profile remote_id Switch(config-dhcp-profile)#
  • D-Link DGS-3130 | Emulator - Page 197
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide "Ethernet"; Any ASCII characters outside of the quotation marks will be interpreted as hexadecimal values.  A formatted key string is a string that should be translated before
  • D-Link DGS-3130 | Emulator - Page 198
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide  ASCII strings can be any combination of formatted key strings, 0-9, A-F, a-f, and space characters. The formatted key strings only support keywords which support hexadecimal value. Space not in the formatted key string will be ignored
  • D-Link DGS-3130 | Emulator - Page 199
    dot none number DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies that when using "." as delimiter, the format is: AA.BB.CC.DD.EE.FF. Specifies that when not using any delimiter, the format is:
  • D-Link DGS-3130 | Emulator - Page 200
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the DHCP Option 82 profile configuration. Example This example shows how
  • D-Link DGS-3130 | Emulator - Page 201
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ip dhcp relay information option mac-format Case Delimiter DHCP client unicast packets. Switch#configure terminal Switch(config)#service dhcp Switch(config)#interface ethernet 1/0/2 Switch(config-if)#ip dhcp relay Switch(config
  • D-Link DGS-3130 | Emulator - Page 202
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 19. DHCP Server Commands 19-1 address range This command is used to specify an IP address range to be associated with a DHCP class in a DHCP
  • D-Link DGS-3130 | Emulator - Page 203
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 19-2 bootfile This command is used to specify the configuration file or image file for the DHCP client to boot the device. Use the no
  • D-Link DGS-3130 | Emulator - Page 204
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 12. Usage Guideline Use this command to delete the binding of addresses. If pool is specified
  • D-Link DGS-3130 | Emulator - Page 205
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to delete the address from the conflict table. The deleted address will be returned to
  • D-Link DGS-3130 | Emulator - Page 206
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to clear all of DHCP statistic counters. Example This example shows how to reset all DHCP counters to zero. Switch#
  • D-Link DGS-3130 | Emulator - Page 207
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch(config-dhcp-class)# exit Switch(config)# ip dhcp class Service-B Switch(config-dhcp-class)# option 60 hex 556677 Switch(config used to specify the unique DHCP client ID of the manual binding entry in a DHCP address pool. Use the no
  • D-Link DGS-3130 | Emulator - Page 208
    Parameters IDENTIFIER DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies a DHCP client identifier in hexadecimal notation. Default None. Command Mode DHCP Pool Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is valid for manual binding entries
  • D-Link DGS-3130 | Emulator - Page 209
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode DHCP Pool Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the default routers for the clients. The
  • D-Link DGS-3130 | Emulator - Page 210
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip dhcp pool .1.1.1 19-11 hardware-address This command is used to specify the hardware address of the manual binding entry in the DHCP address pool. Use the no form of this command to remove the
  • D-Link DGS-3130 | Emulator - Page 211
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide HARDWARE-ADDRESS Specifies the MAC address of the client. -dhcp-pool)# 19-12 host This command is used to specify the IP address of the manual binding entry in a DHCP address pool. Use the no form of this command to remove
  • D-Link DGS-3130 | Emulator - Page 212
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode DHCP Pool Configuration Mode. Command Default Level Level: client-identifier command with the host command to specify the manual binding entry based on client identifier. Use the hardware-address command with the host command to
  • D-Link DGS-3130 | Emulator - Page 213
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how a DHCP class Service-A is configured and defined with a DHCP Option 60 matching pattern 0x112233. Switch# configure terminal Switch(config)# ip dhcp class Service-A Switch(config-dhcp-class)# option 60 hex
  • D-Link DGS-3130 | Emulator - Page 214
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip dhcp ping packets COUNT no ip dhcp ping packets Parameters COUNT Specifies the number of ping packets that the DHCP server will send. Default
  • D-Link DGS-3130 | Emulator - Page 215
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global 12. Usage Guideline A DHCP server receives requests from DHCP clients and services and then allocates an IP address from the address pool and replies the to specify a manual binding entry in a DHCP address pool. 211
  • D-Link DGS-3130 | Emulator - Page 216
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how a DHCP address pool "pool1" is created. Switch# configure terminal Switch(config)# ip dhcp pool pool1 Switch(config-dhcp-pool)# 19-
  • D-Link DGS-3130 | Emulator - Page 217
    HOURS MINUTES infinite DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies the number of hours for the duration of the lease. (Optional) Specifies the number of minutes for the duration of the lease. Specifies
  • D-Link DGS-3130 | Emulator - Page 218
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode DHCP Pool Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the NetBIOS node type of the Microsoft
  • D-Link DGS-3130 | Emulator - Page 219
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to configure the WINS name server IP addresses that that are available to the Microsoft client. Up to eight servers
  • D-Link DGS-3130 | Emulator - Page 220
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 19-23 network This command is used to configure that contain the sub-network are branches under the root, and the address pools that contain the manual binding entry is the leave under the branch or under the root. Based on the tree
  • D-Link DGS-3130 | Emulator - Page 221
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 19-24 option This command is used to configure DHCP server options. Use the no form of this command to remove a specific option. option CODE {
  • D-Link DGS-3130 | Emulator - Page 222
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide  Option 50 (Requested address, default option).  Option 53 (DHCP Message Type, default option).  Option 54 (Server Identifier, default option).  Option 55 (Parameter request list, default option).  Option 61 (Client Identifier,
  • D-Link DGS-3130 | Emulator - Page 223
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode DHCP Class Configuration Mode. dhcp-class)# option 60 hex 102030 Switch(config-dhcp-class)# exit Switch(config)# ip dhcp class Service-B Switch(config-dhcp-class)# option 60 hex 5566 * Switch(config-dhcp-class)# option 60
  • D-Link DGS-3130 | Emulator - Page 224
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to enable the DHCP server and relay service on the Switch. Example This example shows how to disable the DHCP server and relay
  • D-Link DGS-3130 | Emulator - Page 225
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ip dhcp binding IP address Client-ID/ Lease expiration Type Hardware address 10.0.0.1 01002211223344 Feb 25 2017 08:18 AM Automatic Switch# This
  • D-Link DGS-3130 | Emulator - Page 226
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip dhcp conflict 10.1.1.1 IP address Detected Method Detection time 10.1.1.1 Ping Oct 23 2013 09:12 AM Switch# This example shows how
  • D-Link DGS-3130 | Emulator - Page 227
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ip dhcp pool pool1 Pool name: pool1 Network: 10.0.0.0/8 Boot file: Default router: DNS server: NetBIOS server: Domain name: Lease: 1 days 0 hours 0 minutes
  • D-Link DGS-3130 | Emulator - Page 228
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip dhcp server DHCP Service: Disable Ping packets number: 3 Ping timeout: 500 ms Excluded Addresses 10.1.1.1-10.1.1.255 List of DHCP server configured address pool pool1 pool2 pool3 pool5 pool6
  • D-Link DGS-3130 | Emulator - Page 229
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip dhcp server statistics Address pools 3 Automatic bindings 100 Manual binding 2 Malformed messages 0 Renew messages 0 Message BOOTREQUEST DHCPDISCOVER DHCPREQUEST DHCPDECLINE DHCPRELEASE DHCPINFORM Received 12
  • D-Link DGS-3130 | Emulator - Page 230
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 20. DHCP Server Screening Commands 20-1 based . These binding entries restrict that only specific servers are allowed to offer addresses to service specific clients. Example This example shows how to configure a DHCP server screen profile
  • D-Link DGS-3130 | Emulator - Page 231
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 12. Usage Guideline Use this command to clear the server screen log buffer. The DHCP server
  • D-Link DGS-3130 | Emulator - Page 232
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# service dhcp Switch(config)# dhcp-server-screen profile campus Switch(config-dhcp-server-screen)# 20-4 ip dhcp snooping server-screen This command is used to enable
  • D-Link DGS-3130 | Emulator - Page 233
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# dhcp-server-screen profile campus-profile Switch(config-dhcp-server-screen)# based-on hardware-address 00-08-01-02-03-
  • D-Link DGS-3130 | Emulator - Page 234
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ip dhcp server-screen log Parameters None. Default None. VLAN Server IP Client MAC Occurrence 100 10.20.1.1 100 10.58.2.30 00-20-30-40-50-60 10-22-33-44-50-60 06:30:37, 2013-02-07 06:31:42, 2013-02-07 Total Entries
  • D-Link DGS-3130 | Emulator - Page 235
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this feature is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline When DHCP server screening is enabled
  • D-Link DGS-3130 | Emulator - Page 236
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 21. DHCP Snooping Commands 21-1 ip dhcp snooping This command is used to globally enable DHCP snooping. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 237
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The DHCP snooping function validates the DHCP packets when it arrives at the
  • D-Link DGS-3130 | Emulator - Page 238
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to store the DHCP binding entry to local flash or remote server. Use the follow methods to store DHCP binding
  • D-Link DGS-3130 | Emulator - Page 239
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 21-5 clear ip dhcp snooping binding This command is . Usage Guideline Use this command to clear the DHCP binding entry, including the manually configured binding entry. Example This example shows how to clear all snooping binding entries
  • D-Link DGS-3130 | Emulator - Page 240
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level store/dhcp-snp-bind Switch# 21-7 ip dhcp snooping binding This command is used to manually configure a DHCP snooping entry. ip dhcp snooping binding MAC-ADDRESS vlan VLAN-ID IP
  • D-Link DGS-3130 | Emulator - Page 241
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to create a dynamic DHCP snooping entry. Example This example shows how to configure a DHCP snooping entry with IP address 10.1.1.1
  • D-Link DGS-3130 | Emulator - Page 242
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable DHCP snooping trust for port 1/0/3. Switch# configure terminal Switch(config)# interface ethernet 1/0/3 Switch(config-if)# ip dhcp snooping
  • D-Link DGS-3130 | Emulator - Page 243
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip dhcp snooping limit rate {VALUE | no-limit} no ip dhcp snooping limit rate Parameters VALUE no-limit Specifies the number of DHCP messages that
  • D-Link DGS-3130 | Emulator - Page 244
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline When DHCP snooping station move is enabled, the dynamic DHCP snooping binding entry with the same VLAN ID
  • D-Link DGS-3130 | Emulator - Page 245
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 21-13 ip dhcp snooping vlan This command is used to enable DHCP snooping on a VLAN or a group of VLANs. Use the no command to
  • D-Link DGS-3130 | Emulator - Page 246
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ip dhcp snooping Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this
  • D-Link DGS-3130 | Emulator - Page 247
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide vlan VLAN-ID interface INTERFACE-ID , - (Optional) Specifies to display the binding entry based on the VLAN. (Optional) Specifies to display the binding entry based
  • D-Link DGS-3130 | Emulator - Page 248
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip dhcp snooping binding 10.1.1.11 00-01-02-00-00-05 MAC Address IP Address Lease(seconds) Type VLAN Interface 00-01-
  • D-Link DGS-3130 | Emulator - Page 249
    Interface DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The interface that connects to the DHCP client host. 21-16 show ip dhcp snooping database This command is used to display the statistics of
  • D-Link DGS-3130 | Emulator - Page 250
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Checksum errors Unsupported vlans The number of calculated checksum values that is not equal to the stored checksum. The number of the entries of which the VLAN is disabled. 246
  • D-Link DGS-3130 | Emulator - Page 251
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 22. DHCPv6 Client Commands 22-1 clear ipv6 dhcp client This command is used to restart the DHCPv6 client on an interface. clear ipv6 dhcp client
  • D-Link DGS-3130 | Emulator - Page 252
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to enable the prefix delegation request through an interface. The
  • D-Link DGS-3130 | Emulator - Page 253
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the device's DHCPv6 DUID or use the show ipv6 dhcp interface
  • D-Link DGS-3130 | Emulator - Page 254
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 23. DHCPv6 Guard Commands 23-1 ipv6 dhcp guard policy This command is used to create or modify a DHCPv6 guard policy. This command will enter into
  • D-Link DGS-3130 | Emulator - Page 255
    Parameters client server DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies that the attached device is a DHCPv6 client. All DHCPv6 server messages are dropped on this port. Specifies that the attached device is a DHCPv6 server.
  • D-Link DGS-3130 | Emulator - Page 256
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline This command is used to filter DHCPv6 server message based on sender's IP address. If the match ipv6
  • D-Link DGS-3130 | Emulator - Page 257
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/3 Switch(config-if)# ipv6 dhcp guard attach-policy pol1 Switch(config-if)# 23-5 show ipv6 dhcp guard policy
  • D-Link DGS-3130 | Emulator - Page 258
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Source Address Match Access List The IPv6 access list of the specified policy. 254
  • D-Link DGS-3130 | Emulator - Page 259
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 24. DHCPv6 Relay Commands 24-1 ipv6 dhcp relay destination This command is used to enable the DHCP for IPv6 relay service , both can be a link scoped address or a global scoped address. For link scoped addresses, the interface where
  • D-Link DGS-3130 | Emulator - Page 260
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 24-2 ipv6 dhcp relay remote-id format This command is used to configure the sub-type of the remote ID. Use the no form of
  • D-Link DGS-3130 | Emulator - Page 261
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide expert-udf F01. Sub Type: The number 3 indicates that this is the remote ID. F02. User Defined: The user-defined string configured in the ipv6
  • D-Link DGS-3130 | Emulator - Page 262
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is used to enable
  • D-Link DGS-3130 | Emulator - Page 263
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the policy of the DHCPv6 relay agent Remote ID option to dropping the packet if it has a relay
  • D-Link DGS-3130 | Emulator - Page 264
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 24-6 show ipv6 dhcp This command is used to display the DHCPv6 related settings on the interface. show ipv6 dhcp [interface [INTERFACE-ID]] Parameters INTERFACE-
  • D-Link DGS-3130 | Emulator - Page 265
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ipv6 dhcp relay information option Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline
  • D-Link DGS-3130 | Emulator - Page 266
    cid vendor1 DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide | Sub Type | VLAN ID | | 1 byte | 2 bytes | F01. Sub Type: The number 1 indicates that this is the interface ID. F02. VLAN ID: The incoming VLAN ID
  • D-Link DGS-3130 | Emulator - Page 267
    expert-udf DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide | F21 | F22 | F23 | F24 | F25 | | 0 | / | 0 | / | Chassis ID | | (0x30) | (0x2F) | (0x30) | (0x2F) | | | 1 byte | 1 byte | 1 byte | 1 byte | 1~2 byte | | F26 | F27 | F28 | F29 |
  • D-Link DGS-3130 | Emulator - Page 268
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide User Defined Max. 255 bytes F01. User Defined: The flexible user-defined string configured in the ipv6 dhcp relay interface-id format-type expert-udf,
  • D-Link DGS-3130 | Emulator - Page 269
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command is used to enable the insertion of the DHCPv6 relay agent interface ID option function. Example This example shows how to
  • D-Link DGS-3130 | Emulator - Page 270
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 24-11 ipv6 dhcp local-relay vlan This command is used to enable DHCPv6 local relay on a VLAN or a group of VLANs. Use the no
  • D-Link DGS-3130 | Emulator - Page 271
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ipv6 dhcp relay enable no ipv6 dhcp relay enable Parameters None. Default By default, this option is enabled. Command Mode Interface Configuration Mode. Command Default
  • D-Link DGS-3130 | Emulator - Page 272
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to create or remove a profile for DHCPv6 relay Option 37, or enter the DHCPv6 Profile Configuration mode. Example This example
  • D-Link DGS-3130 | Emulator - Page 273
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide format string STRING no format string Parameters STRING Specifies the user-defined DHCP Option 82 format with a maximum of 255 characters. The rules that need
  • D-Link DGS-3130 | Emulator - Page 274
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide module: Indicates the module ID number. This can be strings, 0-9, A-F, a-f, and space characters. The formatted key strings only support keywords which support hexadecimal value. Space not in the formatted key string will be ignored.
  • D-Link DGS-3130 | Emulator - Page 275
    Parameters lowercase uppercase hyphen colon dot none number DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies that when using the lowercase format, the Option 18 or Option 37 MAC address for the user-defined profile will be formatted as: aa-
  • D-Link DGS-3130 | Emulator - Page 276
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ipv6 dhcp relay information option mac-format Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1.
  • D-Link DGS-3130 | Emulator - Page 277
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to configure the Option 37 expert UDF string per port. Example This example shows how
  • D-Link DGS-3130 | Emulator - Page 278
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 24-20 show ipv6 dhcp relay interface-id profile This command is used to display Option 18 profiles. show ipv6 dhcp relay interface-id profile
  • D-Link DGS-3130 | Emulator - Page 279
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display Option 37 profiles. Example This example shows how to display Option
  • D-Link DGS-3130 | Emulator - Page 280
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 25. DHCPv6 Server Commands 25-1 address infinite. If the lifetime is not specified, the default valid lifetime value is 2592000 seconds (30 days). (Optional) Specifies the preferred lifetime of the address prefix in seconds. This value
  • D-Link DGS-3130 | Emulator - Page 281
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 25-2 address-assignment This command is used to specify an address to be assigned to a specified client. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 282
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ipv6 dhcp pool pool1 Switch(dhcpv6-config)# address-assignment 2001:0DB8::1:2 000300010506BBCCDDEE Switch(dhcpv6-config)# exit Switch(config)# interface vlan
  • D-Link DGS-3130 | Emulator - Page 283
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 25-4 domain-name This command is used to configure a domain name to be assigned to the requesting DHCPv6 client. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 284
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode DHCPv6 Pool Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the DNS IPv6 server address to be
  • D-Link DGS-3130 | Emulator - Page 285
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ipv6 dhcp ipv6 dhcp server command to enable the DHCP IPv6 server service on an interface and specify the IPv6 DHCP pool used to service the DHCP request received on the interface. Example This
  • D-Link DGS-3130 | Emulator - Page 286
    rapid-commit DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies to use a two-message This example shows how to create the DHCP pool "pool1", enable the DHCP IPv6 server service on the interface VLAN 100 using the DHCP pool "pool1" to delegate the prefixes. Switch
  • D-Link DGS-3130 | Emulator - Page 287
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ASSIGNED-LENGTH Specifies the prefix length or infinite. If the lifetime is not specified, the default valid lifetime is 2592000 seconds (30 days). (Optional) Specifies the preferred lifetime of the prefix in seconds. This value must be
  • D-Link DGS-3130 | Emulator - Page 288
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode DHCPv6 Pool Configuration infinite. If the lifetime is not specified, the default valid lifetime is 2592000 seconds (30 days). (Optional) Specifies the preferred lifetime of the prefix in seconds. This value
  • D-Link DGS-3130 | Emulator - Page 289
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode DHCPv6 Pool Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to specify a local IPv6 prefix pool in a IPv6 DHCP pool to delegate the prefix for clients serviced by the
  • D-Link DGS-3130 | Emulator - Page 290
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to globally enable the IPv6 DHCP server and relay service on the Switch. The configuration changes of the DHCPv6 server cannot take effect in real-time, disable and enable the DHCPv6 server to make the
  • D-Link DGS-3130 | Emulator - Page 291
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ipv6 dhcp interface vlan 1 vlan 1 is in server mode IPv6 DHCP pool is test Preference value: 0 Hint from client: ignored Rapid-Commit is
  • D-Link DGS-3130 | Emulator - Page 292
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ipv6 dhcp binding Client DUID : 00030001aabbcd000001 address: 1234::2 preferred lifetime 200 ,valid lifetime 300 Client DUID : 00030001aabbcd000000 address: 1234::3 preferred lifetime 200 ,valid
  • D-Link DGS-3130 | Emulator - Page 293
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ipv6 dhcp pool DHCPv6 pool: pool1 Static bindings: Binding for client 00030001aabbcd000080 IA PD: IA ID 0x0001 Prefix: 3000:0:300::/48 preferred lifetime
  • D-Link DGS-3130 | Emulator - Page 294
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ipv6 excluded-address Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this
  • D-Link DGS-3130 | Emulator - Page 295
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display the settings for a specific local IPv6 prefix pool or the setting for all prefix
  • D-Link DGS-3130 | Emulator - Page 296
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to display the operational information for the DHCPv6 server. Example This example shows how to the operational information for the
  • D-Link DGS-3130 | Emulator - Page 297
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 26. Digital Diagnostics Monitoring (DDM) Commands 26-1 show interfaces transceiver This command is used to display the current SFP/SFP+ module operating parameters. show interfaces [
  • D-Link DGS-3130 | Emulator - Page 298
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show interfaces transceiver ++ : high alarm, + : high warning Transceiver Monitoring is enabled Transceiver Monitoring shutdown action: None Current Temperature(C) 30.803 Voltage(V) 3.284 Bias Current(mA) 7.890 TX Power(mW)
  • D-Link DGS-3130 | Emulator - Page 299
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this feature is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline If no optional parameter is specified,
  • D-Link DGS-3130 | Emulator - Page 300
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The port shutdown feature is controlled by the Error Disable module without a recover timer. Users can manually . If the SFP/SFP+ module being configured does not support the threshold change, the user-configured threshold is stored in
  • D-Link DGS-3130 | Emulator - Page 301
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The no form of this command has the effect to clear the configured threshold stored in the system. It does not change the threshold stored
  • D-Link DGS-3130 | Emulator - Page 302
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface then written into the SFP/SFP+ module. If the SFP/SFP+ module configured does not support the threshold change, the user-configured threshold is just stored in the system and the
  • D-Link DGS-3130 | Emulator - Page 303
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the then written into the SFP/SFP+ module. If the SFP/SFP+ module configured does not support the threshold change, the user-configured threshold is just stored in the system and the displayed
  • D-Link DGS-3130 | Emulator - Page 304
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# transceiver- then written into the SFP/SFP+ module. If the SFP/SFP+ module configured does not support the threshold change, the user-configured threshold is just stored in the system and the
  • D-Link DGS-3130 | Emulator - Page 305
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The no form of this command has the and then written into the SFP/SFP+ module. If the SFP/SFP+ module configured does not support the threshold change, the user-configured threshold is just stored in the system and the displayed value
  • D-Link DGS-3130 | Emulator - Page 306
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the low alarm voltage threshold as 0.005 on ethernet 1/0/21. Switch# configure terminal Switch(config)# transceiver-monitoring voltage ethernet 1/0/21 low alarm 0.005 Switch(config)# 302
  • D-Link DGS-3130 | Emulator - Page 307
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 27. D-Link Discovery Protocol (DDP) Client Commands 27-1 ddp This command is used to enable DDP client function globally or on the specified ports. Use the no
  • D-Link DGS-3130 | Emulator - Page 308
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ddp report-timer {30 | 60 | 90 | 120 | Never} no ddp report-timer Parameters 30 60 90 120 Never Specifies the report interval to 30 seconds. Specifies the report interval to 60 seconds. Specifies the report interval to 90 seconds.
  • D-Link DGS-3130 | Emulator - Page 309
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display the DDP information of the Switch. Example This example shows how to display DDP global information. Switch#show ddp D-Link Discovery Protocol state: Enabled
  • D-Link DGS-3130 | Emulator - Page 310
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 28. Domain Name System (DNS) Commands 28-1 clear host This command is used to clear the dynamically learned host entries in the privileged user mode.
  • D-Link DGS-3130 | Emulator - Page 311
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline The system supports the DNS caching name server function. When the caching name server function is enabled and IP domain-lookup, the system forwards the DNS query packet
  • D-Link DGS-3130 | Emulator - Page 312
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip dns lookup static Switch(config)# 28-4 ip domain lookup This command is used to enable the DNS to carry
  • D-Link DGS-3130 | Emulator - Page 313
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IPV6-ADDRESS Specifies the IPv6 address of the equipment. Default None. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The host
  • D-Link DGS-3130 | Emulator - Page 314
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to configure a DNS server. When the system cannot obtain an answer from a DNS server, it
  • D-Link DGS-3130 | Emulator - Page 315
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 28-8 show hosts This command is used to display the DNS configuration. show hosts Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any
  • D-Link DGS-3130 | Emulator - Page 316
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ip name-server Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this
  • D-Link DGS-3130 | Emulator - Page 317
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 29. DoS Prevention Commands 29-1 dos- dos-prevention with the all keyword is used to disable the DoS prevention mechanism for all supported types. All the related settings will be reverted back to the default for the specified attack
  • D-Link DGS-3130 | Emulator - Page 318
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide NOTE: Some functions using the NTP protocol might not Switch(config)# This example shows how to enable the DoS prevention mechanism on all supported types. Switch# configure terminal Switch(config)# dos-prevention all Switch(config)# This
  • D-Link DGS-3130 | Emulator - Page 319
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show dos-prevention DoS Prevention Information DoS Type State Land Attack Enabled Blat Attack Enabled TCP Null Disabled TCP Xmas Disabled TCP SYN-FIN
  • D-Link DGS-3130 | Emulator - Page 320
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the sending of traps for DoS attacking. Switch# configure terminal Switch(config)# snmp-server enable traps dos-prevention Switch(config)# 316
  • D-Link DGS-3130 | Emulator - Page 321
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 30. Dynamic ARP Inspection Commands 30-1 arp access-list This 0.0.255.255 mac any Switch(config-arp-nacl)# permit ip 10.30.0.0 0.0.255.255 mac any Switch(config-arp-nacl)# 30-2 clear ip arp inspection log This command is used to clear
  • D-Link DGS-3130 | Emulator - Page 322
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 12. Usage Guideline Use this command to clear the ARP inspection log buffer. Example This example
  • D-Link DGS-3130 | Emulator - Page 323
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# clear ip arp inspection statistics vlan 1 Switch# 30-4 ip arp inspection filter vlan This command is used to specify an ARP access list to be used for ARP inspection checks for the VLAN.
  • D-Link DGS-3130 | Emulator - Page 324
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 30-5 ip arp inspection limit This command is used . Example This example shows how to limit the rate of the incoming ARP requests to 30 packets per second and to set the interface monitoring interval to 5 consecutive seconds. Switch#
  • D-Link DGS-3130 | Emulator - Page 325
    Parameters NUMBER DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the buffer entry number. Switch# configure terminal Switch(config)# ip arp inspection log-buffer entries 64 Switch(config)# 30-7 ip arp inspection trust This command is used to trust an interface for dynamic
  • D-Link DGS-3130 | Emulator - Page 326
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline When an interface is in the (config)# interface ethernet 1/0/3 Switch(config-if)# ip arp inspection trust Switch(config-if)# 30-8 ip arp inspection validate This command is used to specify the additional checks to be
  • D-Link DGS-3130 | Emulator - Page 327
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable source MAC validation. Switch# configure terminal Switch(config)# ip arp inspection validate src-mac Switch(config)# 30-9 ip arp inspection vlan This command is used to enable specific VLANs for
  • D-Link DGS-3130 | Emulator - Page 328
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip arp inspection vlan VLAN-ID [, | -] logging {acl-match {permit | deny | all | none} | dhcp-bindings {permit | deny | all | none}} no ip arp inspection vlan VLAN-
  • D-Link DGS-3130 | Emulator - Page 329
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 30-11 permit | deny (arp access-list) This 20.0.0 255.255.0.0 mac any Switch(config-arp-nacl)# permit ip 10.30.0.0 255.255.0.0 mac any Switch(config-arp-nacl)# 30-12 show ip arp inspection This command is used to display the status of
  • D-Link DGS-3130 | Emulator - Page 330
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ip arp inspection [interfaces [INTERFACE-ID [, | -]] | statistics [vlan VLAN-ID [, | -]]] Parameters interfaces INTERFACE-ID , - statistics vlan VLAN-ID , - (Optional) Specifies a port, range of ports
  • D-Link DGS-3130 | Emulator - Page 331
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip arp inspection statistics VLAN ----1 2 10 100 200 1024 VLAN ----1 2 10 100 200 1024 VLAN ----1 2 10 100 200 1024 Forwarded Dropped DHCP Drops
  • D-Link DGS-3130 | Emulator - Page 332
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ip arp inspection Source MAC Validation : Enabled Destination MAC Validation: Disabled IP Address Validation : Disabled VLAN State ACL Match Static ACL 10 Disabled
  • D-Link DGS-3130 | Emulator - Page 333
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ip arp inspection interfaces Interface Trust State Rate(pps over which the interface is monitored for the high rate of the ARP packets. 30-13 show ip arp inspection log This command is used to display the ARP inspection
  • D-Link DGS-3130 | Emulator - Page 334
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. eth1/0/2 100 10.5.10.16 55-66-20-30-40-50 2 (2013-12-02 00:11:54) eth1/0/3 100 10.58.2.30 10-22-33-44-50-60 1 (2013-12-30 12:01:38) Total Entries: 3 Switch# Display
  • D-Link DGS-3130 | Emulator - Page 335
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 31. Error Recovery Commands 31-1 errdisable by L2PT guard. Specifies to enable the auto-recovery option for an error port caused by D-Link Unidirectional. Specifies the time, in seconds, to recover the port from the error state caused by
  • D-Link DGS-3130 | Emulator - Page 336
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide manually recover the port by entering the shutdown command first and then the no shutdown command for the port. Example This example shows how to set
  • D-Link DGS-3130 | Emulator - Page 337
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show errdisable recovery ErrDisable Cause Port Security Storm Control BPDU Attack Protection Dynamic ARP Inspection DHCP Snooping Loop Detection l2pt-guard D-LINK Unidirectional Link Detection State ----------disabled disabled
  • D-Link DGS-3130 | Emulator - Page 338
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline If no optional parameter is specified, it will enable or disable the SNMP notifications for both entering and exiting the error disabled state.
  • D-Link DGS-3130 | Emulator - Page 339
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 32. Ethernet OAM Commands 32-1 ethernet oam This command is used to enable the Ethernet OAM function on the specified port. Use the no form
  • D-Link DGS-3130 | Emulator - Page 340
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, the Ethernet OAM mode is active. Command Switch(config-if)# ethernet oam mode active Switch(config-if)# 32-3 ethernet oam link-monitor error-symbol This command is used to enable notifying the Ethernet OAM error symbol
  • D-Link DGS-3130 | Emulator - Page 341
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline The link monitoring function counts Switch(config)# interface ethernet 1/0/1 Switch(config-if)# ethernet oam link-monitor error-symbol threshold 100 Switch(config-if)# This example shows
  • D-Link DGS-3130 | Emulator - Page 342
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide threshold NUMBER window DECISECONDS (Optional) Specifies terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# no ethernet oam link-monitor error-frame Switch(config-if)# This example shows how to configure
  • D-Link DGS-3130 | Emulator - Page 343
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# ethernet oam link-monitor error-frame window 100 Switch(config-if)# This example shows how to configure ethernet 1/0/1 Ethernet OAM error frame monitor
  • D-Link DGS-3130 | Emulator - Page 344
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# ethernet oam link )# interface ethernet 1/0/1 Switch(config-if)# no ethernet oam link-monitor error-frame-seconds Switch(config-if)# This example shows
  • D-Link DGS-3130 | Emulator - Page 345
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default The Ethernet OAM error frame period event Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# ethernet oam link-monitor error-frame-period Switch(config-if)# This example shows how to disable
  • D-Link DGS-3130 | Emulator - Page 346
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# no ethernet oam link-monitor error-frame-period threshold Switch(config-if)# 32-7 ethernet oam remote-failure dying-gasp This command is used to enable
  • D-Link DGS-3130 | Emulator - Page 347
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default The Ethernet OAM critical event will be notified by default. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command
  • D-Link DGS-3130 | Emulator - Page 348
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command is used to request the remote peer to enter or exit the Ethernet OAM remote loopback mode. Use the ethernet oam
  • D-Link DGS-3130 | Emulator - Page 349
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 32-11 show ethernet oam configuration This command is used to display the configuration of the Ethernet OAM function. show ethernet oam configuration [interface INTERFACE-
  • D-Link DGS-3130 | Emulator - Page 350
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ethernet oam configuration interface ethernet 1/0/1 eth1/0/1 Ethernet oam state Mode Dying gasp Critical event Remote loopback OAMPDU : Disabled : Active : Enabled : Enabled : Not Processed
  • D-Link DGS-3130 | Emulator - Page 351
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide indicates that the OAM entity supports the transmission of OAMPDUs on links that are operating in unidirectional 30 MIB Disable: OAM is disabled on this port LinkFault: The link has detected a fault and is transmitting OAMPDUs with a link
  • D-Link DGS-3130 | Emulator - Page 352
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide SendLocalAndRemote: The local port has discovered the peer but has not yet accepted or rejected the configuration of the peer. SendLocalAndRemoteOk: The local device agrees
  • D-Link DGS-3130 | Emulator - Page 353
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ethernet oam statistics interface ethernet 1/0/1 eth1/0/1 Information OAMPDU TX : 0 Information OAMPDU RX : 0 Unique Event Notification OAMPDU TX : 0 Unique Event Notification OAMPDU RX : 0 Duplicate
  • D-Link DGS-3130 | Emulator - Page 354
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to clear the Ethernet OAM statistics of ethernet 1/0/1. Switch# clear ethernet oam statistics interface ethernet 1/0/1 Switch# 32-15 show ethernet
  • D-Link DGS-3130 | Emulator - Page 355
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ethernet oam event-log interface ethernet 1/0/1 eth1/0/1 Local Faults 0 Link Fault records 0 Dying Gasp records 0 Critical Event records Remote Faults 0 Link Fault records 2 Dying Gasp records Event index Time stamp
  • D-Link DGS-3130 | Emulator - Page 356
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 32-16 clear ethernet oam event-log This command is used to clear the event log of the Ethernet OAM function. clear ethernet oam event-
  • D-Link DGS-3130 | Emulator - Page 357
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 33. Ethernet Ring Protection Switching (ERPS) Commands 33-1 description This command is used to specify a string that serves as a description for a G.8032 Ethernet ring instance.
  • D-Link DGS-3130 | Emulator - Page 358
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Use the Ethernet ring G.8032 command to create or modify a G.8032 ring and
  • D-Link DGS-3130 | Emulator - Page 359
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#configure terminal Switch(config)#ethernet ring g8032 profile campus Switch(config-erps-ring-profile)#timer guard 700 Switch(config-erps-ring-profile)#timer hold-
  • D-Link DGS-3130 | Emulator - Page 360
    Parameters VLAN-ID DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the VLAN ID of the APS channel VLAN for the ERPS vlan-ids VLAN-ID [, | -] Parameters VLAN-ID Specifies the VLAN ID of the service protected VLANs of the ERPS instance. The valid range from is 1 to 4094. 356
  • D-Link DGS-3130 | Emulator - Page 361
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide , (Optional) Specifies a series of VLANs, or separate a range of protected by the ERPS instance. Example This example shows how to configure the service protected VLAN as 100 to 200 for ERPS instance 1. Switch# configure terminal Switch
  • D-Link DGS-3130 | Emulator - Page 362
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to create an ERPS instance under a physical ring. Deploy multiple instances in the same physical
  • D-Link DGS-3130 | Emulator - Page 363
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch(config)#ethernet ring g8032 major-ring Switch(config-erps-ring)#port0 interface ethernet 1/0/1 Switch(config-erps-ring)#port1 none Switch(config-erps-ring)#instance 1
  • D-Link DGS-3130 | Emulator - Page 364
    Parameters INSTANCE-ID DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the identifier of an ERPS instance. The valid range is from 1 to 32. Default None. Command Mode ERPS Instance Configuration Mode. Command Default Level
  • D-Link DGS-3130 | Emulator - Page 365
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline To change the profile association, deactivate the ERPS instance first. Example This example shows how to configure the
  • D-Link DGS-3130 | Emulator - Page 366
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode ERPS Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the first ring port of a physical ring. Example
  • D-Link DGS-3130 | Emulator - Page 367
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ethernet in some cases it is desirable to revert to this working transport entity once all ring links are available. This is performed at the expense of an additional traffic interruption. In
  • D-Link DGS-3130 | Emulator - Page 368
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 33-15 rpl This command is used to configure the node as the RPL owner, neighbor and assign the RPL port. Use the no form
  • D-Link DGS-3130 | Emulator - Page 369
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide RING-NAME PROFILE-NAME INSTANCE-ID (Optional) Specifies to display information of the specified ERPS physical ring. (Optional) Specifies to display information of the specified
  • D-Link DGS-3130 | Emulator - Page 370
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to display detailed information of the ERPS physical ring "ring1". Switch#show ethernet ring g8032 status ring1 Ethernet Ring ring1 Admin
  • D-Link DGS-3130 | Emulator - Page 371
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ethernet ring g8032 status major-ring instance 1 Instance value of the ERPS instance. The APS channel VLAN of the ERPS instance. Service protected VLANs of the ERPS instance. The profile associated with the ERPS instance. The
  • D-Link DGS-3130 | Emulator - Page 372
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Revertive / Non-revertive Instance Status RPL ERPS instance can be activated. In addition to these configurations, the configuration of service protected VLANs and RPL related settings are fundamental for operation of an ERPS instance
  • D-Link DGS-3130 | Emulator - Page 373
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 33-18 timer This command is used to configure timers for an ERPS profile. Use the no form of this command to revert to the
  • D-Link DGS-3130 | Emulator - Page 374
    Parameters RING-ID DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the identifier of a physical ring. The valid range is from 1 to 239. Default None. Command Mode ERPS Configuration Mode. Command Default Level Level: 12.
  • D-Link DGS-3130 | Emulator - Page 375
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage an instance port immediately after force is configured, irrespective of whether link failures have occurred. This command is used in ERPSv2 only. 33-22 erps manual switch ring_port This command is used to block an ERPS instance
  • D-Link DGS-3130 | Emulator - Page 376
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide erps manual switch ring_port {port0 | port1} Parameters port0 port1 Specifies to manually block ERPS instance port0. Specifies to manually block ERPS instance port1. Default None. Command Mode ERPS Instance Configuration Mode. Command
  • D-Link DGS-3130 | Emulator - Page 377
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline A clear command will remove the effects of the force and manual commands. The clear command also provides the following functions:  Triggers revertive switching before the WTR or WTB timer expires in the case of revertive
  • D-Link DGS-3130 | Emulator - Page 378
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 34. File System Commands 34-1 cd This command 2000 23:57:11 5 -rw 12791928 Jan 05 2000 23:09:30 6 d-- 0 Jan 23 2000 03:49:07 runtime.had config.cfg firmware.had fw5.had backup.had system 125304832 bytes total (70426624 bytes free)
  • D-Link DGS-3130 | Emulator - Page 379
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 34-2 delete This command is used to delete a file. delete FILE-URL Parameters FILE-URL Specifies the name of the file to be deleted. Default
  • D-Link DGS-3130 | Emulator - Page 380
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline If the file system and appears to the user as a subdirectory under the root directory. The supported file systems can be displayed as the user issues the dir command for the root directory.
  • D-Link DGS-3130 | Emulator - Page 381
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# format /d: All sectors will be erased, proceed? (y/n) [n] y Enter volume id (up to 11 characters):Profiles Format completed. Switch# 34-5 mkdir This command is used
  • D-Link DGS-3130 | Emulator - Page 382
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command # more /c:/configuration/usr_def.conf !DGS-3130 !Firmware Version: 1.00.001 !Slot Model ! 1 DGS-3130-30TS ! 2 - ! 3 DGS-3130-30TS ! 4 DGS-3130-30TS ! ip igmp snooping vlan
  • D-Link DGS-3130 | Emulator - Page 383
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline A file can be renamed to a file located either within the same directory or to another directory. Example This example shows how to rename
  • D-Link DGS-3130 | Emulator - Page 384
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show storage media-info [unit UNIT-ID] Parameters unit UNIT-ID (Optional) Specifies the unit ID in the stacking system. If not specified, all units
  • D-Link DGS-3130 | Emulator - Page 385
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 35. Filter Database (FDB) Commands 35-1 clear mac-address-table This command is used to delete a specific dynamic MAC address, all dynamic MAC addresses on a
  • D-Link DGS-3130 | Emulator - Page 386
    Parameters SECONDS DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the aging time in seconds. The valid range is 0 or 10 to 1000000 seconds. Setting the aging time to 0 will disable the MAC address
  • D-Link DGS-3130 | Emulator - Page 387
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The source MAC address triggered update function is always enabled. The hit bit of MAC address entries corresponding to the port that receives
  • D-Link DGS-3130 | Emulator - Page 388
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide By default, MAC address learning is always enabled on all VLANs on the Switch when VLAN is created. MAC address learning will be recovered to
  • D-Link DGS-3130 | Emulator - Page 389
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline When the Switch learns or removes a MAC address, a notification can be sent to the notification history table and
  • D-Link DGS-3130 | Emulator - Page 390
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline For a unicast MAC address entry, only one interface can be specified. For a multicast MAC address entry, multiple interfaces
  • D-Link DGS-3130 | Emulator - Page 391
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to set the multicast filtering mode on VLAN 100 to filter unregistered. Switch# configure terminal Switch(config)# vlan 100 Switch(
  • D-Link DGS-3130 | Emulator - Page 392
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show mac-address-table address 00-23-7D-BC-08-44 VLAN ---1 MAC Address 00-23-7D-BC-08-44 Type ---------Dynamic Ports eth1/0/5
  • D-Link DGS-3130 | Emulator - Page 393
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display the MAC address table's
  • D-Link DGS-3130 | Emulator - Page 394
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline If no optional parameter is specified, all physical ports will be displayed. Example This example shows how to display the MAC address learning
  • D-Link DGS-3130 | Emulator - Page 395
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the MAC address notification change configuration on all interfaces. Switch#show mac-address-table notification change interface Interface
  • D-Link DGS-3130 | Emulator - Page 396
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 35-12 show multicast filtering-mode This command is used to display the filtering mode for handling multicast packets that are received on an interface.
  • D-Link DGS-3130 | Emulator - Page 397
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to enable the sending of SNMP MAC notification traps. Example
  • D-Link DGS-3130 | Emulator - Page 398
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/2 Switch(config-if)# snmp trap mac-notification change added Switch(config-if)# 394
  • D-Link DGS-3130 | Emulator - Page 399
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 36. GARP VLAN Registration Protocol (GVRP) Commands 36-1 clear gvrp statistics This command is used to clear the statistics for a GVRP port. clear gvrp statistics {
  • D-Link DGS-3130 | Emulator - Page 400
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Administrators can enable the global GVRP
  • D-Link DGS-3130 | Emulator - Page 401
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# gvrp enable Switch(config-if)# 36-4 gvrp advertise This command is used to specify the
  • D-Link DGS-3130 | Emulator - Page 402
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# gvrp advertise 1000 Switch(config-if)# 36-5 gvrp vlan create This command is used to
  • D-Link DGS-3130 | Emulator - Page 403
    add remove VLAN-ID , - DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies a VLAN or a list of VLANs to be added to the forbidden VLAN list. (Optional) Specifies a VLAN or a list of VLANs to be removed
  • D-Link DGS-3130 | Emulator - Page 404
    leave leave-all TIMER-VALUE DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies to set the timer for nni-bpdu-address This command is used to configure the GVRP BPDU address in the service provider site. Use the no form of this command to revert to the default setting
  • D-Link DGS-3130 | Emulator - Page 405
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default that behave as the NNI ports in the service provider site. Example This example shows how to configure the GVRP PDU address in service provider site to dot1d. Switch# configure
  • D-Link DGS-3130 | Emulator - Page 406
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the GVRP configuration for the global configuration. Switch# show gvrp configuration Global GVRP State : Enabled Dynamic VLAN Creation :
  • D-Link DGS-3130 | Emulator - Page 407
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline This command only displays the ports which have the GVRP state enabled. Example This example shows how to display
  • D-Link DGS-3130 | Emulator - Page 408
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 37. Gratuitous ARP Commands 37-1 ip arp gratuitous This command is used to enable the learning of gratuitous ARP packets in the ARP cache table.
  • D-Link DGS-3130 | Emulator - Page 409
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level of gratuitous ARP request. The device will send out the packet when an IP interface becomes link-up or when the IP address of an interface is configured or modified. Use the ip
  • D-Link DGS-3130 | Emulator - Page 410
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the sending of gratuitous ARP messages. Switch# configure terminal Switch(config)# ip gratuitous-arps Switch(config)# interface vlan
  • D-Link DGS-3130 | Emulator - Page 411
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 38. Interface Commands 38-1 clear counters This command is used to clear counters for the specified interfaces. clear counters {all | interface INTERFACE-ID [, | -]} Parameters all
  • D-Link DGS-3130 | Emulator - Page 412
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The specified number with no spaces in between. The following keywords can be used for the supported interface types: 408
  • D-Link DGS-3130 | Emulator - Page 413
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide  Ethernet - Specifies the physical Ethernet switch port with all channel command to remove a portchannel. For a null interface, the null0 interface is supported and can't be removed. For a loopback interface or a tunnel interface, the
  • D-Link DGS-3130 | Emulator - Page 414
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# no interface loopback2 Switch (config)# 38-4 interface range This command is used to enter the interface range configuration mode for
  • D-Link DGS-3130 | Emulator - Page 415
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show counters [interface INTERFACE-ID] Parameters interface INTERFACE-ID (Optional) Specifies that the interface can be a physical port, port channel or VLAN interfaces. If no
  • D-Link DGS-3130 | Emulator - Page 416
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide txHCPkt128to255Octets txHCPkt256to511Octets txHCPkt512to1023Octets txHCPkt1024to1518Octets txHCPkt1519to1522Octets txHCPkt1519to2047Octets txHCPkt2048to4095Octets txHCPkt4096to9216Octets : 27683 : 5822 : 270 : 2230 : 0 : 0 : 0 : 0
  • D-Link DGS-3130 | Emulator - Page 417
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide txHCOctets rxHCPkt64Octets rxHCPkt65to127Octets rxHCPkt128to255Octets rxHCPkt256to511Octets rxHCPkt512to1023Octets rxHCPkt1024to1518Octets rxHCPkt1519to1522Octets rxHCPkt1519to2047Octets rxHCPkt2048to4095Octets rxHCPkt4096to9216Octets
  • D-Link DGS-3130 | Emulator - Page 418
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide txHCPkt1024to1518Octets txHCPkt1519to1522Octets txHCPkt1519to2047Octets txHCPkt2048to4095Octets txHCPkt4096to9216Octets txHCPkt9217to16383Octet s rxCRCAlignErrors rxUndersizedPkts rxFragmentPkts rxSymbolErrors txCollisions ifInErrors
  • D-Link DGS-3130 | Emulator - Page 419
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide dot3StatsSingleColFrame s Transmit Single Collision Frame Counter. 10/100 mode only-incremented for each frame transmitted which experienced exactly one collision during transmission. dot3StatsMultiColFrames Transmit Multiple
  • D-Link DGS-3130 | Emulator - Page 420
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the VLAN interface information for interface VLAN 1. Switch#show interfaces vlan 1 vlan 1 is enabled, Link status is up Interface type: VLAN Interface description: MAC address: F0-7D-68-36-30-B0
  • D-Link DGS-3130 | Emulator - Page 421
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show interfaces ethernet 1/0/1 Eth1/0/1 is enabled link status is up Interface type port 0. Switch#show interfaces mgmt 0 mgmt_ipif 0 is enabled, Link status is up Interface type: Management port Switch# 38-7 show interfaces
  • D-Link DGS-3130 | Emulator - Page 422
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command allows the user to display general, error or
  • D-Link DGS-3130 | Emulator - Page 423
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show interfaces ethernet 1/0/1,1/0/3 counters errors Port CrcAlign-Err / Undersize / Rcv-Err / InDiscard / Xmit-Err OutDiscard eth1/0/1 0 0 0 100 0 0 eth1/0/3 0 0 0 0 0 0 Port Single-Col / Excess-Col /
  • D-Link DGS-3130 | Emulator - Page 424
    DeferredTx IntMacTx DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide refer to the item "txDelayExceededDiscards" in Display Parameters in the show counters command. refer to the item "dot3StatsInternalMacTransmitErrors" in Display Parameters in the show counters
  • D-Link DGS-3130 | Emulator - Page 425
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show interfaces status Port Status VLAN Duplex Speed Type eth1/0/1 connected 1 a-full a-100 1000BASE-T eth1/0/2 not-connected 1 auto auto 1000BASE-T eth1/0/3 not-connected 1 auto
  • D-Link DGS-3130 | Emulator - Page 426
    utilization DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional)Specifies a range of interfaces. No space is allowed before or after the hyphen. (Optional) Specifies to display the utilization information. Default None. Command Mode
  • D-Link DGS-3130 | Emulator - Page 427
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 38-10 show interfaces gbic This command is used to display GBIC status information. show interfaces [INTERFACE-ID [, | -]] gbic Parameters INTERFACE-ID , gbic (Optional) Specifies
  • D-Link DGS-3130 | Emulator - Page 428
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show interfaces [INTERFACE-ID [, | -]] auto-negotiation Parameters INTERFACE-ID , auto-negotiation (Optional) 38-12 show interfaces description This command is used to display the description and link status of interfaces. 424
  • D-Link DGS-3130 | Emulator - Page 429
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show interfaces [INTERFACE-ID [, | -]] description Parameters INTERFACE is allowed before or after the hyphen. Specifies to display the description and link status of interfaces. Default None. Command Mode User/Privileged EXEC Mode. Any
  • D-Link DGS-3130 | Emulator - Page 430
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show interfaces description Interface Status Administrative Description eth1/0/1 up enabled eth1/0/2 down enabled eth1/0/3 down enabled eth1/0/4 down enabled eth1/0/5 down enabled eth1/0/6 down
  • D-Link DGS-3130 | Emulator - Page 431
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The command will cause the port to enter the disabled state. Under the disabled state, the port will not be able to receive or transmit
  • D-Link DGS-3130 | Emulator - Page 432
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 39. Internet Group Management Protocol (IGMP) Snooping Commands 39-1 clear ip igmp snooping statistics This command is used to clear the IGMP snooping related statistics.
  • D-Link DGS-3130 | Emulator - Page 433
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The IGMP snooping global state is disabled. Command Mode Interface Configuration Mode. Global Configuration Mode. Command Default Level Level: 12. Usage Guideline In the interface
  • D-Link DGS-3130 | Emulator - Page 434
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode or port-channel interface configuration. Example This example shows how to restrict the serviced IGMP snooping group for ethernet 1/0/1 to group 226.1.1.1. In the following example
  • D-Link DGS-3130 | Emulator - Page 435
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command is only available for physical port and port-channel interface configuration. Use this command to enable or disable accounting when a listener
  • D-Link DGS-3130 | Emulator - Page 436
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 39-6 ip igmp snooping fast-leave This command is used to configure IGMP Snooping fast-leave on the interface. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 437
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is only available for VLAN interface configuration. An IGMP snooping switch is aware of link-layer topology changes caused by the
  • D-Link DGS-3130 | Emulator - Page 438
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the last member query interval time to be 3 seconds. Switch# configure terminal Switch(config)# vlan 1000 Switch(config-
  • D-Link DGS-3130 | Emulator - Page 439
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/4 Switch(config-if)# ip igmp snooping limit 80 except igmp_filter vlan 1000 Switch(config-if)# This example shows
  • D-Link DGS-3130 | Emulator - Page 440
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to add an IGMP snooping static multicast router port for VLAN 1. Switch# configure terminal Switch(config)# vlan 1 Switch(config-vlan)#
  • D-Link DGS-3130 | Emulator - Page 441
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip igmp snooping querier no ip igmp snooping querier Parameters None. Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default
  • D-Link DGS-3130 | Emulator - Page 442
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline This command is only available for VLAN interface configuration. The query interval is the interval between General Queries
  • D-Link DGS-3130 | Emulator - Page 443
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 39-15 ip igmp snooping query-version This command is used to configure the general query packet version sent by the IGMP snooping querier. Use
  • D-Link DGS-3130 | Emulator - Page 444
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command packet that can be processed by IGMP snooping. Example This example shows how to limit 30 packets per second on interface VLAN 1000. Switch# configure terminal Switch(config)# vlan 1000
  • D-Link DGS-3130 | Emulator - Page 445
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable report suppression on VLAN 1. Switch# configure terminal Switch(config)# vlan 1 Switch(config-vlan)# ip igmp snooping report-suppression
  • D-Link DGS-3130 | Emulator - Page 446
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# vlan 1000 Switch( to create an IGMP snooping static group in case that the attached host does not support the IGMP protocol. Example This example shows how to statically add a group and source
  • D-Link DGS-3130 | Emulator - Page 447
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 39-20 ip igmp snooping suppression-time This command is used to configure the time for suppressing duplicate IGMP reports or leaves. Use the no
  • D-Link DGS-3130 | Emulator - Page 448
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is only available for VLAN interface configuration. This setting only applies
  • D-Link DGS-3130 | Emulator - Page 449
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display IGMP snooping information for all VLANs where IGMP snooping is enabled. Example This example
  • D-Link DGS-3130 | Emulator - Page 450
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display IGMP snooping authentication and
  • D-Link DGS-3130 | Emulator - Page 451
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display IGMP snooping group information. Example This example shows how to display IGMP snooping group
  • D-Link DGS-3130 | Emulator - Page 452
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display command is used to display IGMP snooping multicast router information that has been automatically learned and manually configured on the Switch. show ip igmp snooping mrouter [vlan VLAN-ID [, | -]]
  • D-Link DGS-3130 | Emulator - Page 453
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display dynamically learned or manually configured multicast router interfaces. Example
  • D-Link DGS-3130 | Emulator - Page 454
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays the IGMP snooping related statistics information. Example
  • D-Link DGS-3130 | Emulator - Page 455
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline This command is used to display statically configured IGMP snooping groups on the Switch. If no optional parameter is
  • D-Link DGS-3130 | Emulator - Page 456
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 40. IP Source Guard Commands 40-1 ip verify port ACL. Port ACL is a hardware mechanism and its entry can come from either a manual configured entry or the DHCP snooping binding database. The packet that fails to pass the validation will
  • D-Link DGS-3130 | Emulator - Page 457
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide MAC-ADDRESS vlan VLAN-ID IP-ADDRESS interface INTERFACE-ID , - Specifies the MAC address of the IP-to-MAC address binding entry. Specifies the VLAN
  • D-Link DGS-3130 | Emulator - Page 458
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IP-ADDRESS MAC-ADDRESS dhcp-snooping static snooping. (Optional) Specifies to display the IP-source guard binding entry that is manually configured. (Optional) Specifies to display the IP-source guard binding entry based on
  • D-Link DGS-3130 | Emulator - Page 459
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ip source binding 10.1.1.10 MAC by the user. The IP address lease time. The binding type. Static bindings are configured manually. Dynamic binding are learned from DHCP snooping. The VLAN number of the client interface. The
  • D-Link DGS-3130 | Emulator - Page 460
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the hardware port ACL entries
  • D-Link DGS-3130 | Emulator - Page 461
    IP address MAC address VLAN DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The client's IP address assigned from the DHCP server or configured by the user. The client's MAC address. The VLAN number of the client interface. 457
  • D-Link DGS-3130 | Emulator - Page 462
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 41. IP Utility Commands 41-1 ping This command is used to diagnose basic network connectivity. ping {[ip] IP-ADDRESS | [ipv6] IPV6-ADDRESS | HOST-NAME} [length
  • D-Link DGS-3130 | Emulator - Page 463
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to verify the reachability, reliability, and delay of the path to the destination host. Be sure to set the count
  • D-Link DGS-3130 | Emulator - Page 464
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline This command datagrams with an Initial TTL of 1 is sent. The maximum TTL value is 30. The timeout period is 5 seconds. The destination base UDP port number is 33434. The query number for
  • D-Link DGS-3130 | Emulator - Page 465
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline To interrupt this command after the command has been issued, press Ctrl-C. This
  • D-Link DGS-3130 | Emulator - Page 466
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# traceroute 2001:238:f8a:77:7c10:41c0:6ddd:ecab
  • D-Link DGS-3130 | Emulator - Page 467
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip forward-protocol udp [PORT] no ip forward-protocol udp [PORT] Parameters PORT (Optional) Specifies the destination port of the UDP service to be forwarded or not forwarded. Default Common used application protocols are enabled.
  • D-Link DGS-3130 | Emulator - Page 468
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any 1.1.1.11 1.1.1.12 1.1.1.13 1.1.1.14 1.1.1.15 1.1.1.16 1.1.1.17 1.1.1.18 1.1.1.19 1.1.1.20 30.90.90.88 Switch# 41-7 show ip forward-protocol udp This command is used
  • D-Link DGS-3130 | Emulator - Page 469
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any information. Switch#show ip forward-protocol udp Application Time Service IEN-116 Name Service TACACS TFTP NetBIOS-NS NetBIOS-DS UDP Port 37 42 49 69 137
  • D-Link DGS-3130 | Emulator - Page 470
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 42. IP-MAC-Port Binding (IMPB) Commands 42-1 clear ip ip-mac-port-binding violation This command is used to clear IP-MAC-Port Binding (
  • D-Link DGS-3130 | Emulator - Page 471
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline When a port is enabled for IMPB
  • D-Link DGS-3130 | Emulator - Page 472
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the IMPB configuration or use the show ip ip-mac-port-
  • D-Link DGS-3130 | Emulator - Page 473
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this feature is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline When IP-MAC-Port Binding notifies
  • D-Link DGS-3130 | Emulator - Page 474
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 43. IPv6 Snooping Commands 43-1 ipv6 snooping policy This command is used to create or modify an IPv6 snooping policy. This command will enter the
  • D-Link DGS-3130 | Emulator - Page 475
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, all protocols are disabled. Command Mode IPv6 Snooping Configuration Mode. Command Default Level Level: 12. Usage Guideline Neighbor Discovery (ND) snooping is
  • D-Link DGS-3130 | Emulator - Page 476
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline This command is used to limit the number of IPv6 binding entries on which the IPv6 snooping policy
  • D-Link DGS-3130 | Emulator - Page 477
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 43-5 ipv6 snooping station-move deny This command is used to deny the station move function for IPv6 snooping entries. Use the no form of
  • D-Link DGS-3130 | Emulator - Page 478
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display DHCPv6 guard information. If no parameter is specified, information is displayed
  • D-Link DGS-3130 | Emulator - Page 479
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 44. IPv6 Source Guard Commands 44-1 ipv6 source Command Default Level Level: 12. Usage Guideline The command is used to set the static manual binding entry of the binding table. When configuring this command, the specified VLAN does not
  • D-Link DGS-3130 | Emulator - Page 480
    Parameters POLICY-NAME DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the name of the source guard policy. configured global addresses. It is useful when all global addresses on a link are assigned by DHCP and the administrator wants to block hosts with self-configured addresses
  • D-Link DGS-3130 | Emulator - Page 481
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to deny auto-configured traffic. Switch# configure terminal Switch(config)# ipv6 source-guard policy policy1 Switch(config-source-guard)# deny global-autoconfig Switch(config-source-guard)# 44-4 permit link-
  • D-Link DGS-3130 | Emulator - Page 482
    Parameters None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this feature is enabled. Command Mode Source-guard Policy Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is used
  • D-Link DGS-3130 | Emulator - Page 483
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the IPv6 policy will permit packets sent by the auto-configured address and deny packets sent by the link-local address. Example This example shows how to apply the IPv6 source guard policy "pol1"
  • D-Link DGS-3130 | Emulator - Page 484
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ipv6 source-guard policy [POLICY-NAME] Parameters POLICY-NAME (Optional) Specifies the name of the source guard policy. Default None. Command Mode User/Privileged
  • D-Link DGS-3130 | Emulator - Page 485
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline The command is used to display the entries of the
  • D-Link DGS-3130 | Emulator - Page 486
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 45. Jumbo Frame Commands 45-1 max-rcv-frame-size This command is used to configure the maximum Ethernet frame size allowed. Use the no form
  • D-Link DGS-3130 | Emulator - Page 487
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 46. Layer 2 Protocol Tunnel (L2PT) Commands 46-1 clear l2protocol-tunnel counters This command is used to clear the Layer 2 Protocol Tunnel (L2PT) statistics counters. clear
  • D-Link DGS-3130 | Emulator - Page 488
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode packet to the remote site via a trunk port, the tunneled packet will be tagged with service VLAN. The packet can also be forwarded to other ports at the local site which are
  • D-Link DGS-3130 | Emulator - Page 489
    Parameters COS-VALUE DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the CoS value. The values is enabled for the Layer 2 protocol tunnel, the Switch encapsulates the packet with a service VLAN tag and rewrites the CoS with the value specified by this command. Example This
  • D-Link DGS-3130 | Emulator - Page 490
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline The tunneling of Layer 2 protocol packets will consume CPU processing power when encapsulating, decapsulating and forwarding packets. Use
  • D-Link DGS-3130 | Emulator - Page 491
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable rate limiting globally. Switch# configure terminal Switch(config)# l2protocol-tunnel global drop-threshold 5000 Switch(config)# 46-6 l2protocol-
  • D-Link DGS-3130 | Emulator - Page 492
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# l2protocol-tunnel shutdown-threshold stp 200 Switch(config-if)# 46-7 show l2protocol-tunnel This command
  • D-Link DGS-3130 | Emulator - Page 493
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show l2protocol-tunnel CoS for Encapsulated Packets :5 Port Shutdown Threshold Drop Threshold Encap Counter Decap Counter Indicates the Class of Service (CoS) value for tunneled L2 protocol packets. Indicates the rate limiting on
  • D-Link DGS-3130 | Emulator - Page 494
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 47. Link Aggregation Control Protocol (LACP) Commands 47-1 channel-group This command is used to assign an interface to a channel group. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 495
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 47-2 lacp port-priority This command is used to information and there will be 1 second between LACP PDU periodic transmissions when the link partner uses Short Timeouts. Specifies that there will be 90 seconds before invalidating received
  • D-Link DGS-3130 | Emulator - Page 496
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, the LACP timeout mode is short. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is available
  • D-Link DGS-3130 | Emulator - Page 497
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the LACP system priority to be 30000. Switch# configure terminal Switch(config)# lacp system-priority 30000 Switch(config)#
  • D-Link DGS-3130 | Emulator - Page 498
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# port-channel load-balance src-ip Switch(config)# 47-6 show channel-group This command is used to display the channel
  • D-Link DGS-3130 | Emulator - Page 499
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show channel-group channel detail Flag: S - Port is requesting Slow LACPDUs F - Port is requesting fast LACPDU A - Port is in active mode P - Port is in
  • D-Link DGS-3130 | Emulator - Page 500
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show channel-group sys-id System-ID: 32768,F0-7D-68-34-00-10 Switch# This example shows how to display the summary information
  • D-Link DGS-3130 | Emulator - Page 501
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 48. Link Layer Discovery Protocol (LLDP) Commands 48-1 clear lldp counters This command is used to delete LLDP statistics. clear lldp counters [all | interface INTERFACE-ID [, | -]] Parameters
  • D-Link DGS-3130 | Emulator - Page 502
    Parameters all INTERFACE-ID , - DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to clear LLDP neighboring information for all interfaces. Specifies the interface ID. Valid interfaces are physical interfaces. (Optional) Specifies a series of interfaces or separates a
  • D-Link DGS-3130 | Emulator - Page 503
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide , vlan-name VLAN-ID , protocol-identity PROTOCOL-NAME (Optional) of the network. For example, protocols like Spanning Tree Protocol, Link Aggregation Control Protocol, and numerous vendor proprietary variations are responsible for
  • D-Link DGS-3130 | Emulator - Page 504
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface mac-phy-cfg | link-aggregation | max-frame-size] no lldp dot3-tlv-select [mac-phy-cfg | link-aggregation | max-frame-size] Parameters mac-phy-cfg link-aggregation max-frame-size
  • D-Link DGS-3130 | Emulator - Page 505
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default if the advertisement state is enabled. When no optional parameter is specified, all supported IEEE 802.3 organizationally specific TLVs are selected or de-selected in this command.
  • D-Link DGS-3130 | Emulator - Page 506
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the LLDP MED fast start repeat count. Switch# configure terminal Switch(config)# lldp fast-count 10 Switch(config)#
  • D-Link DGS-3130 | Emulator - Page 507
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IP-ADDRESS IPV6-ADDRESS (Optional) Specifies the IPv4 address that is carried in the management address TLV. (Optional) Specifies the IPv6 address that is carried
  • D-Link DGS-3130 | Emulator - Page 508
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to delete the management address FE80::250:A2FF:FEBF:A056 from ethernet 1/0/3. and 1/0/4. Switch# configure terminal Switch(config)# interface range ethernet 1/0/3-1/0/4
  • D-Link DGS-3130 | Emulator - Page 509
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 receive no lldp receive Parameters None. Default LLDP is enabled on all supported interfaces. Command Mode Interface Configuration Mode. Command Default Level Level: 12.
  • D-Link DGS-3130 | Emulator - Page 510
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this value is 2 seconds. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline A re-enabled LLDP physical interface will
  • D-Link DGS-3130 | Emulator - Page 511
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable LLDP. Switch# configure terminal Switch(config)# lldp run Switch(config)# 48-12 lldp forward This command is used
  • D-Link DGS-3130 | Emulator - Page 512
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide port-description system-capabilities system- and sent to other devices. Example This example shows how to enable all supported optional 802.1AB basic management TLVs. Switch# configure terminal Switch(config)# interface
  • D-Link DGS-3130 | Emulator - Page 513
    Parameters None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default LLDP transmit is enabled on all supported interfaces. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is available for physical port configuration.
  • D-Link DGS-3130 | Emulator - Page 514
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The LLDP transmission interval must be greater The range is from 5 to 32768 seconds. Default By default, this value is 30 seconds. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline
  • D-Link DGS-3130 | Emulator - Page 515
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide snmp-server enable traps lldp [med] no snmp-server enable traps lldp [med] Parameters med (Optional) Specifies to enable the LLDP-MED trap state. Default
  • D-Link DGS-3130 | Emulator - Page 516
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use the lldp notification enable command to enable the sending of LLDP notifications. Use the lldp med notification enable command to enable the
  • D-Link DGS-3130 | Emulator - Page 517
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 48-20 show lldp This command is used to display the general LLDP configuration of the Switch. show lldp Parameters None. Default None. Command Mode
  • D-Link DGS-3130 | Emulator - Page 518
    Firmware Revision : 1.00.001 Software Revision : 1.00.001 Serial Number : DGS3130111013 Manufacturer Name : D-Link Corporation Model Name : DGS-3130-30TS Gigabit Ethernet S Asset ID : LLDP Configurations LLDP State : Disabled LLDP Forward State : Disabled Message TX Interval : 30
  • D-Link DGS-3130 | Emulator - Page 519
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. IEEE 802.3 Organizationally Specific TLVs: :Disabled MAC/PHY Configuration/Status Link Aggregation Maximum Frame Size Energy Efficient Ethernet :Disabled :Disabled :Disabled
  • D-Link DGS-3130 | Emulator - Page 520
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Display Parameters Enabled Management Address Displays the enabled IPv4/IPv6 addresses. '(None)' means that the user did not configure the management address with the lldp
  • D-Link DGS-3130 | Emulator - Page 521
    3 Stackable Managed Switch CLI Reference Guide Switch#show lldp local interface ethernet 1/0/1 detail Port ID: eth1/0/1 Port ID Subtype : Local Port ID : eth1/0/1 Port Description : D-Link Corporation DGS-3130-30TS HW A1 firmware 1.00.001 Port 1 on Unit 1 Port PVID : 1 Management
  • D-Link DGS-3130 | Emulator - Page 522
    Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show lldp local interface ethernet 1/0/1 brief Port ID: eth1/0/1 Port ID Subtype : Local Port ID : eth1/0/1 Port Description : D-Link Corporation DGS-3130-30TS HW A1 firmware 1.00.001 Port 1 on Unit 1 Switch# 48-23 show lldp
  • D-Link DGS-3130 | Emulator - Page 523
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show lldp management-address Address 1 : (default) Subtype : IPv4 Address : 10.90.90.90 IF Type : IfIndex OID : 1.3.6.1.4.1.171.10.118.2 Advertising Ports : - Address 2 : Subtype :
  • D-Link DGS-3130 | Emulator - Page 524
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Power Via MDI : (None) Link Aggregation : (None) Maximum Frame support : LLDP-MED capabilities : Support Network Policy : Support Location identification : Not Support Extended power via MDI : Support Inventory : Support
  • D-Link DGS-3130 | Emulator - Page 525
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide VLAN ID Priority DSCP Unknown Tagged Inventory Management (None) : : : : True : : Switch# This example shows how to display remote LLDP information in the normal mode. 521
  • D-Link DGS-3130 | Emulator - Page 526
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Description : Stackable Ethernet Switch System Capabilities Supported : Repeater, Bridge System Capabilities Enabled : : (See Detail) Power Via MDI : (See Detail) Link Aggregation : (See Detail) Maximum Frame Size : 1536 LLDP-
  • D-Link DGS-3130 | Emulator - Page 527
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show lldp neighbor interface ethernet 1/0/1-1/0/2 brief Port ID: eth1/0/1 Remote Entities Count : 2 Entity 1 Chassis ID Subtype : MAC Address Chassis ID : 00-01-02-03-
  • D-Link DGS-3130 | Emulator - Page 528
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline The global LLDP traffic information displays an overview of neighbor
  • D-Link DGS-3130 | Emulator - Page 529
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of interfaces. No space is allowed before or after the hyphen. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode.
  • D-Link DGS-3130 | Emulator - Page 530
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide trunk or hybrid ports when the partner switch does not support the loop detection function. When port-based detection is that were disabled by loopback detection. Alternatively, manually recover the port by entering the shutdown command
  • D-Link DGS-3130 | Emulator - Page 531
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the port-based loopback detection function globally and set the detection mode to port-based. Switch# configure terminal
  • D-Link DGS-3130 | Emulator - Page 532
    Parameters SECONDS DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the interval in seconds at which LBD packets are transmitted. The valid range is from 1 to 32767. Default By default, this value is 10
  • D-Link DGS-3130 | Emulator - Page 533
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to configure the list of VLANs that are enabled for loop detection. The command setting takes effect when the port's
  • D-Link DGS-3130 | Emulator - Page 534
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#sh loopback-detection Loop Detection Detection Mode LBD enabled VLAN Interval Action Mode Address Type Function Version : Enabled : port-based : all VLANs : 20 seconds :
  • D-Link DGS-3130 | Emulator - Page 535
    Parameters shutdown none DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to shut down the port in the port-based mode or block traffic on the specific VLAN in the VLAN-based mode when a loop
  • D-Link DGS-3130 | Emulator - Page 536
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command is used to enable the sending of SNMP notifications for loopback detection. Use the no command to return to the default
  • D-Link DGS-3130 | Emulator - Page 537
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 50. MAC Authentication Commands 50-1 mac-auth system-auth-control This command is used to enable MAC authentication globally. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 538
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default enabled on the port.  The MAC authentication port cannot be enabled on a link aggregation port. Example This example shows how to enable MAC authentication on ethernet 1/0/1.
  • D-Link DGS-3130 | Emulator - Page 539
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command is used to configure the password used in the authentication of MAC address users. If the command is not configured, the
  • D-Link DGS-3130 | Emulator - Page 540
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 50-5 snmp-server enable traps mac-auth This command is used to enable the sending of SNMP notifications for MAC authentication. Use the no form
  • D-Link DGS-3130 | Emulator - Page 541
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 51. Mirror Commands 51-1 monitor session destination interface This command is used to configure the destination interface for a monitor session, allowing packets on source ports
  • D-Link DGS-3130 | Emulator - Page 542
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide monitor session SESSION-NUMBER destination remote vlan VLAN-ID interface INTERFACE-ID monitor session SESSION-NUMBER destination remote vlan access-list ACCESS-LIST-NAME replace
  • D-Link DGS-3130 | Emulator - Page 543
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# monitor session 2 source interface ethernet 1/0/2-4 Switch(config)# monitor session 2 destination remote vlan 100 interface ethernet 1/0/6 Switch(config)# 51-3 monitor session
  • D-Link DGS-3130 | Emulator - Page 544
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to create a port monitor The valid range is 1 to 4. Specifies the flow-based mirror. Only the ingress mirror is supported and only MAC, IP, or IPv6 access lists can be monitored. Even if the access list
  • D-Link DGS-3130 | Emulator - Page 545
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 51-5 monitor session source remote vlan This command is used to configure the RSPAN VLAN for an RSPAN destination session. Use the no form of
  • D-Link DGS-3130 | Emulator - Page 546
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 51-6 monitor session source vlan This command is used to configure VLANs for VLAN-based monitoring. Use the no form of this command to remove
  • D-Link DGS-3130 | Emulator - Page 547
    Parameters None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, 802.1Q VLAN is used. Command Mode VLAN Configuration Mode. Command Default Level Level: 12. Usage Guideline Use the remote-span command
  • D-Link DGS-3130 | Emulator - Page 548
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline If a monitor session is deleted, all configuration for the session is removed. Example
  • D-Link DGS-3130 | Emulator - Page 549
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show monitor session Session 1 Session Type: local session Destination Port: Ethernet 1/0/1 Source Ports: Both: Ethernet 1/0/2 Ethernet 1/0/3 Ethernet 1/0/4 Total Entries: 1 Switch# 545
  • D-Link DGS-3130 | Emulator - Page 550
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 52. Multicast Listener Discovery (MLD) Snooping Commands 52-1 clear ipv6 mld snooping statistics This command is used to clear MLD snooping statistic counters on the
  • D-Link DGS-3130 | Emulator - Page 551
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The MLD snooping global state is disabled by default. Command Mode Interface Configuration Mode. Global Configuration Mode. Command Default Level Level: 12. Usage Guideline For a
  • D-Link DGS-3130 | Emulator - Page 552
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. or port-channel interface configuration. Example This example shows how to restrict the serviced MLD snooping group for ethernet 1/0/1 to group FF1E::14. In the following
  • D-Link DGS-3130 | Emulator - Page 553
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command is only available for VLAN interface configuration. The ipv6 mld snooping fast-leave command allows MLD membership to be removed from a
  • D-Link DGS-3130 | Emulator - Page 554
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 52-6 ipv6 mld snooping limit This command is used to set the limit of MLD snooping multicast groups or channels which layer 2 interface can join.
  • D-Link DGS-3130 | Emulator - Page 555
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface port-channel 4 Switch(config-if)# no ipv6 mld snooping limit vlan 1000 Switch(config-if)# 52-7 ipv6 mld snooping
  • D-Link DGS-3130 | Emulator - Page 556
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# vlan 1 Switch( is only available for VLAN interface configuration. An MLD snooping switch is aware of link-layer topology changes caused by Spanning Tree operation. When a port is enabled or
  • D-Link DGS-3130 | Emulator - Page 557
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 52-9 ipv6 mld snooping proxy-reporting This command is used to enable the proxy-reporting function. Use the no form of this command to disable
  • D-Link DGS-3130 | Emulator - Page 558
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is only available for VLAN interface configuration. The interface must have
  • D-Link DGS-3130 | Emulator - Page 559
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the MLD snooping query interval to 300 seconds on VLAN 1000. Switch# configure terminal Switch(config)# vlan 1000
  • D-Link DGS-3130 | Emulator - Page 560
    Parameters 1 2 DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies that the version of the MLD general query sent by MLD snooping querier is 1. Specifies that the version of the MLD general query sent
  • D-Link DGS-3130 | Emulator - Page 561
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command is available for VLAN # configure terminal Switch(config)# vlan 1000 Switch(config-vlan)# ipv6 mld snooping rate-limit 30 Switch(config-vlan)# 52-15 ipv6 mld snooping report-suppression This command is used to
  • D-Link DGS-3130 | Emulator - Page 562
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 52-16 ipv6 mld snooping robustness-variable This command is used to set the robustness variable used in MLD snooping. Use the no form of
  • D-Link DGS-3130 | Emulator - Page 563
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IPV6-ADDRESS interface INTERFACE-ID , - Specifies an IPv6 to create an MLD snooping static group in case that the attached host does not support the MLD protocol. Example This example shows how to statically add group and/or
  • D-Link DGS-3130 | Emulator - Page 564
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is only available for VLAN interface configuration. Report suppression will suppress
  • D-Link DGS-3130 | Emulator - Page 565
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# vlan 1 Switch(config-vlan)# ipv6 mld snooping minimum-version 2 Switch(config-vlan)# 52-20 show ipv6 mld snooping This command
  • D-Link DGS-3130 | Emulator - Page 566
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ipv6 mld snooping MLD snooping global state: Enabled VLAN #1 configuration MLD snooping state : Enabled Minimum version : v2 Fast leave : Enabled (host-based) Report
  • D-Link DGS-3130 | Emulator - Page 567
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to display MLD snooping limit and access group information. If no optional parameter is specified, MLD snooping filter information for
  • D-Link DGS-3130 | Emulator - Page 568
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. used to display MLD snooping multicast router information that has been automatically learned and manually configured on the Switch. show ipv6 mld snooping mrouter [vlan VLAN-ID [,
  • D-Link DGS-3130 | Emulator - Page 569
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display dynamically learned or manually configured multicast router interfaces. Example This example shows how to display MLD snooping multicast router information.
  • D-Link DGS-3130 | Emulator - Page 570
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display statically configured MLD snooping groups. Switch#show ipv6 mld snooping static-group VLAN ID Group address Interface 1 FF1E::1 1/0/1-1/0/2
  • D-Link DGS-3130 | Emulator - Page 571
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display MLD snooping statistics information. Switch#show ipv6 mld sn statistics interface Interface eth1/0/4 Rx: v1Report 0, v2Report 0, Query 0, v1Done 0
  • D-Link DGS-3130 | Emulator - Page 572
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 53. Multicast VLAN Commands 53-1 mvlan enable This command is used to enable multicast VLAN and configure some options for the multicast VLAN feature. Use
  • D-Link DGS-3130 | Emulator - Page 573
    ignore-vlan DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide associated default VLAN is either a multicast VLAN or is tagged with a multicast VLAN that does not match the associated profile. Specifies the setting for tagged
  • D-Link DGS-3130 | Emulator - Page 574
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide mvlan vlan VLAN-ID no mvlan vlan VLAN-ID Parameters VLAN-ID Specifies the multicast VLAN. The range is 1 to 4094. Default None. Command Mode
  • D-Link DGS-3130 | Emulator - Page 575
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of interfaces. No space is allowed before or after the hyphen. Default No receiver or source port is a member of any multicast
  • D-Link DGS-3130 | Emulator - Page 576
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Multicast VLAN Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to specify the name of a multicast VLAN. Example This
  • D-Link DGS-3130 | Emulator - Page 577
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command is used to report the join information to the source port. The purpose is to avoid the control packets being dropped
  • D-Link DGS-3130 | Emulator - Page 578
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 53-8 access-group This command is used to bind an access group profile to a multicast VLAN. Use the no form of this command to remove
  • D-Link DGS-3130 | Emulator - Page 579
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IPV6-ADDRESS-START IPV6-ADDRESS-END Specifies the IPv6 multicast start address in the range. Specifies the IPv6 multicast end address in the range. Default
  • D-Link DGS-3130 | Emulator - Page 580
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display all multicast VLAN profiles. Switch#show mvlan group-profile Profile Name mv_profile1 Multicast Address 225.0.0.0 - 225.0.0.5 Total Entries: 1
  • D-Link DGS-3130 | Emulator - Page 581
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 53-12 show mvlan This command is used to display multicast VLAN configurations. show mvlan [VLAN-ID] Parameters VLAN-ID (Optional) Specifies the VLAN ID.
  • D-Link DGS-3130 | Emulator - Page 582
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Forward Unmatched Ignore VLAN Untagged/Tagged Receiver/Source Replace Source IP Replace Priority The forwarding mode for Multicast VLAN unmatched packets. Enabled means to forward
  • D-Link DGS-3130 | Emulator - Page 583
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 54. Neighbor Discovery (ND) Inspection Commands 54-1 ipv6 nd inspection policy1 Switch(config-nd-inspection)# 54-2 validate source-mac This command is used to check the source MAC address against the link-layer address for ND messages.
  • D-Link DGS-3130 | Emulator - Page 584
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode ND Inspection Policy Configuration Mode. Command Default Level Level: 12. Usage Guideline When the Switch receives an ND message that contains a link -inspection)# 54-3 device-role
  • D-Link DGS-3130 | Emulator - Page 585
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide not performed. When performing NS/NA inspection policy policy1 Switch(config-nd-inspection)# device-role host Switch(config-nd-inspection)# 54-4 ipv6 nd inspection attach-policy This command is used to apply an ND inspection policy
  • D-Link DGS-3130 | Emulator - Page 586
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ipv6 nd inspection 1/0/3 Switch(config-if)# ipv6 nd inspection attach-policy policy1 Switch(config-if)# 54-5 show ipv6 nd inspection policy This command is used to display Router Advertisement (
  • D-Link DGS-3130 | Emulator - Page 587
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 55. Network Access Authentication Commands 55-1 authentication guest-vlan This command is used to configure the guest VLAN setting. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 588
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 55-2 authentication host-mode This command is used to specify the authentication mode. Use the no form of this command to revert to the default
  • D-Link DGS-3130 | Emulator - Page 589
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 55-3 authentication periodic This command is used to enable periodic re-authentication for a port. Use the no form of this command to disable periodic re-
  • D-Link DGS-3130 | Emulator - Page 590
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline When the inactivity timer is configured, a user session will be terminated if the
  • D-Link DGS-3130 | Emulator - Page 591
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Switch(config-if)# authentication timer reauthentication 200 Switch(config-if)# 55-6 authentication timer restart This command is used
  • D-Link DGS-3130 | Emulator - Page 592
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 0 7 password PASSWORD vlan VLAN-ID (Optional) Specifies the password in the clear text form. If neither 0 nor 7 are specified, the default form is clear text. (
  • D-Link DGS-3130 | Emulator - Page 593
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 12. Usage Guideline Use this command to clear the authentication sessions. Example This example shows how
  • D-Link DGS-3130 | Emulator - Page 594
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline This command is used to configure the formatting of usernames used for RADIUS authentication or for IGMP security
  • D-Link DGS-3130 | Emulator - Page 595
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to specify ethernet 1/0/1 to operate in the mac-wac mode. Switch#configure terminal Switch(config)#interface ethernet 1/0/1 Switch(config-if)#
  • D-Link DGS-3130 | Emulator - Page 596
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 55-12 authorization disable This command is used to disable the acceptance of the authorized configuration. Use the no form of this command to enable
  • D-Link DGS-3130 | Emulator - Page 597
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide - mac-address MACADDRESS (Optional) Specifies a range of interfaces. No space is allowed before or after the hyphen. (Optional) Specifies to display a specific user. Default None.
  • D-Link DGS-3130 | Emulator - Page 598
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Success - Host pass authentication. Accounting authentication will not start within the block time unless the user clears the entry state manually. Idle Time Idle Time - Indicates the leftover time of an authenticated session that
  • D-Link DGS-3130 | Emulator - Page 599
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide RESPONSE - Indicates that the state machine has received an EAPOLencapsulated EAP Response packet from the supplicant and is relaying the EAP packet to the authentication
  • D-Link DGS-3130 | Emulator - Page 600
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 56. Power over Ethernet (PoE) Commands 56-1 poe pd -if)# poe pd description For VOIP usage 56-2 poe pd legacy-support This command is used to enable support of legacy PD. Use no form of this command to disable it. poe pd
  • D-Link DGS-3130 | Emulator - Page 601
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is available for physical port configuration. Use the command to enable support of legacy PD connected to the port. If legacy support
  • D-Link DGS-3130 | Emulator - Page 602
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide If the policy preempt setting is enabled, then the policy preempt setting is disabled, then the policy is first in first serviced. Thus the new PD will not be serviced if the power budget is running out. If the policy preempt setting is
  • D-Link DGS-3130 | Emulator - Page 603
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 56-5 poe power-inline This command is used . Command Mode Interface configuration mode. Command Default Level Level: 12. Usage Guideline This command is supported only on PoE-capable ports. When the port is set to auto mode, the port will
  • D-Link DGS-3130 | Emulator - Page 604
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch(config)# interface eth3/0/1 Switch(config-if)# poe power-inline auto 5000 This example shows how to disable PD detection and not to power a PoE
  • D-Link DGS-3130 | Emulator - Page 605
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide snmp-server enable traps poe [unit UNIT-ID] no snmp-server enable traps poe [unit UNIT-ID] Parameters UNIT-ID (Optional) Specify the unit to
  • D-Link DGS-3130 | Emulator - Page 606
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage port, power inline configuration status, statistic counters, the measurement result and the data link layer classification using information. If INTERFACE-ID is not specified with this command, then
  • D-Link DGS-3130 | Emulator - Page 607
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This is a sample output from the show poe power-inline status command. Switch> show poe power-inline status Interface State Class Max(W) Used(W) Description
  • D-Link DGS-3130 | Emulator - Page 608
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display PoE power system's power information. Switch> show poe power module Unit Delivered(W) Power Budget(W) Usage-Threshold(%) Preempt Trap
  • D-Link DGS-3130 | Emulator - Page 609
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 57. Policy-based Routing (PBR) Commands 57-1 ip policy route-map This command is used to specify a route map as the routing policy on an
  • D-Link DGS-3130 | Emulator - Page 610
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# route-map pbr-map permit 1 Switch(config-route-map)# match ip address pbr-acl Switch(config-route-map)# set ip
  • D-Link DGS-3130 | Emulator - Page 611
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 58. Port Security Commands 58-1 clear port-security This command is used to delete the auto-learned secured MAC addresses. clear port-security {all | {address
  • D-Link DGS-3130 | Emulator - Page 612
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide interface INTEFACE-ID , address vlan VLAN-ID . - (Optional) Specifies the ID of the interface to be displayed. (Optional) Specifies a series of interfaces or separates a range
  • D-Link DGS-3130 | Emulator - Page 613
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide snmp-server enable traps port-security [trap-rate TRAP-RATE] no snmp-server enable traps port-security [trap-rate] Parameters trap-rate TRAP-RATE (Optional)
  • D-Link DGS-3130 | Emulator - Page 614
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide MAC addresses will not be purged out unless the user manually deletes those entries. (Optional) Specifies that under this function cannot be enabled.  If the port is a link aggregation member port, the port security function cannot be
  • D-Link DGS-3130 | Emulator - Page 615
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide  Shutdown - The interface is disabled, based on errors, when a (config-if)# switchport port-security maximum 5 Switch(config-if)# This example shows how to manually add the secure MAC addresses 00-00-12-34-56-78 with VID 5 at ethernet
  • D-Link DGS-3130 | Emulator - Page 616
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to disable the ageing or set the ageing time for
  • D-Link DGS-3130 | Emulator - Page 617
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to set the limit on the port security entry number
  • D-Link DGS-3130 | Emulator - Page 618
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 59. Power Saving Commands 59-1 dim led This command is used length-detection dim-led port-shutdown Specifies that power saving will be applied by link status. Specifies that power saving will be applied by cable length detection.
  • D-Link DGS-3130 | Emulator - Page 619
    hibernation DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies that power saving will be applied by The user can enable or disable link detection, length detection, dimming LEDs, port shutdown, and hibernation using this command. When link detection is enabled, the device can
  • D-Link DGS-3130 | Emulator - Page 620
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to enable or disable the specified port's EEE power saving
  • D-Link DGS-3130 | Emulator - Page 621
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# power-saving dim-led time-range off-duty Switch(config)# 59-5 power-saving hibernation time-range This command is used
  • D-Link DGS-3130 | Emulator - Page 622
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide PROFILE-NAME Specifies the name of the time configuration information. show power-saving [link-detection] [length-detection] [dim-led] [port-shutdown] [hibernation] [eee] Parameters link-detection length-detection dim-led
  • D-Link DGS-3130 | Emulator - Page 623
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline If no optional parameter is specified, all power saving configuration information will be displayed. Example This example shows how
  • D-Link DGS-3130 | Emulator - Page 624
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 60. PPPoE Circuit-ID Tag Insertion 60-1 pppoe circuit-id-insert This command is used to enable PPPoE circuit ID insertion. pppoe circuit-id-insert
  • D-Link DGS-3130 | Emulator - Page 625
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is available for physical
  • D-Link DGS-3130 | Emulator - Page 626
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The command is available for physical port interface configuration. Example This example shows
  • D-Link DGS-3130 | Emulator - Page 627
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide switch# show pppoe circuit-id-insert Global PPPoE State : Enabled The example shows how to display the setting of PPPoE circuit ID insertion on interface
  • D-Link DGS-3130 | Emulator - Page 628
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 61. Private VLAN Commands 61-1 private-vlan This command is used to configure a VLAN as a private VLAN. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 629
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 61-2 private-vlan association This command is used to associate secondary VLANs with a primary VLAN. Use the no form of this command to remove the
  • D-Link DGS-3130 | Emulator - Page 630
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode MST Configuration Mode. Command Default Level Level: 12. Usage Guideline The secondary VLANs need to be mapped to the same MST ID as
  • D-Link DGS-3130 | Emulator - Page 631
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline For isolated ports or community ports, use the switchport mode private-vlan host command to specify the port mode and use the switchport
  • D-Link DGS-3130 | Emulator - Page 632
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to associate ethernet 1/0/1 with the primary VLAN 1000 and the secondary VLAN 1001. Switch# configure terminal Switch(config)# interface ethernet 1/0/1
  • D-Link DGS-3130 | Emulator - Page 633
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/2 Switch(config-if)# switchport mode private-vlan promiscuous Switch(config-if)# switchport private-vlan mapping 1000 add 1001,
  • D-Link DGS-3130 | Emulator - Page 634
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 62. Protocol Independent Commands 62-1 distance This command is used to define an administrative distance for routing protocols including RIP and BGP. Use the no
  • D-Link DGS-3130 | Emulator - Page 635
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide distance default DISTANCE no distance default Parameters DISTANCE Specifies the administrative distance. The range is from 1 to 255. Default The default distance of a static default
  • D-Link DGS-3130 | Emulator - Page 636
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to configure the distance is an integer from 1 to 255 representing the trust rating of
  • D-Link DGS-3130 | Emulator - Page 637
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# router Usage Guideline Use 0.0.0.0 0.0.0.0 to specify the default route. Floating state route is supported. This means that there could have two routes with the same destination network address
  • D-Link DGS-3130 | Emulator - Page 638
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide to reach the destination network. If the address is a link-local address, then the interface ID also need to be Level Level: 12. Usage Guideline Floating state route is supported. This means that there could have two routes with the
  • D-Link DGS-3130 | Emulator - Page 639
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip route ecmp advance-control mode {VALUE1 | VALUE2 | VALUE3 | VALUE4 } no ip route ecmp advance-control mode Parameters VALUE1 ... VALUE4 Specifies the number of ECMP
  • D-Link DGS-3130 | Emulator - Page 640
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide dip Specifies that the load-balancing algorithm will include the destination IP address. port Specifies that the load-balancing algorithm will include the TCP or
  • D-Link DGS-3130 | Emulator - Page 641
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to display 255.0.0.0) vlan 1 (107.100.0.1/255.255.0.0) Routing Information Sources: Gateway Last Update 11.0.0.2 22:54:09 11.0.0.5 22:53:59 11.0.0.254 22:53:51 Distribute list: East branch (in)
  • D-Link DGS-3130 | Emulator - Page 642
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default vlan 11 O 17.0.0.0/8 [80/3] via 11.0.0.1, vlan 11 O 18.0.0.0/8 [80/3] via 11.0.0.1, vlan 11 O 30.0.0.0/8 [80/2] via 11.0.0.1, vlan 11 O 40.0.0.0/8 [80/3] via 11.0.0.1, vlan 11 I 41.0.0.0/8 [116/10
  • D-Link DGS-3130 | Emulator - Page 643
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays the brief information for the working routing
  • D-Link DGS-3130 | Emulator - Page 644
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline The routing table gathers routes learned from different protocols. If
  • D-Link DGS-3130 | Emulator - Page 645
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ipv6 route summary Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline When the system provides forwarding services for IPv6 traffic, it
  • D-Link DGS-3130 | Emulator - Page 646
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 63. Quality of Service (QoS) Commands 63-1 class This command is used to specify the name of the class map to be associated with a traffic policy and then enter
  • D-Link DGS-3130 | Emulator - Page 647
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide class-map [match-all | match-any] NAME no class-map NAME Parameters match-all match-any NAME (Optional) Specifies how to evaluate multiple match criteria.
  • D-Link DGS-3130 | Emulator - Page 648
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide of service (CoS) marking. Specifies differentiated service code point values to be matched. Enter one or more differentiated service mode. The following lists the reference for the supported protocols for the match protocol command.  arp
  • D-Link DGS-3130 | Emulator - Page 649
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide  ntp - Network Time Protocol.  ospf - Open Shortest Path First.  and a two rate policer for class voice and video-n-data respectively). The service policy configured in this example is attached to ethernet 1/0/1. Switch# configure
  • D-Link DGS-3130 | Emulator - Page 650
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide mls qos aggregate-policer NAME KBPS [BURST-NORMAL [BURST-MAX]] [conform-action ACTION] exceed-action ACTION [violate-action ACTION] [color-aware] mls qos aggregate-policer
  • D-Link DGS-3130 | Emulator - Page 651
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline An aggregate policer can be shared Switch(config-pmap-c)# 63-5 mls qos cos This command is used to configure the default Class of Service (CoS) value of a port. Use the no form of this command to revert to the default
  • D-Link DGS-3130 | Emulator - Page 652
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide mutation This command is used to attach an ingress Differentiated Services Code Point (DSCP) mutation map to the interface. DSCP value. Example This example shows how to map DSCP 30 to the mutated DSCP value 8 and then attach the ingress
  • D-Link DGS-3130 | Emulator - Page 653
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 63-7 mls qos map cos-color This command is used to define the CoS to color map for mapping a packet's initial color. Use the no
  • D-Link DGS-3130 | Emulator - Page 654
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide dscp DSCP-LIST green yellow red Specifies the list of DSCP code point to be mapped to a color. The range is from 0 to 63. The
  • D-Link DGS-3130 | Emulator - Page 655
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The DSCP to CoS map is used by a DSCP trust port to map a
  • D-Link DGS-3130 | Emulator - Page 656
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline When a packet is received by an All the subsequent operations will base on the mutated DSCP. Example This example shows how to map DSCP 30 to the mutated DSCP value 8, DSCP 20 to the mutated DSCP 10, with the mutation map
  • D-Link DGS-3130 | Emulator - Page 657
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide queue in a round robin order. Initially, each queue sets its reaches 0, the credit counters will be replenished at that time. All packets are serviced until their credit counter is zero or negative and the last packet is transmitted
  • D-Link DGS-3130 | Emulator - Page 658
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline When the interface is the following keywords: drop - Drops the packet. set-dscp-transmit VALUE - Sets the IP differentiated services code point (DSCP) value and transmits the packet with the new IP DSCP value. set-1p-
  • D-Link DGS-3130 | Emulator - Page 659
    color-aware DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies the option for the Use the police command to drop the packet or mark the packet with different quality of service (QoS) values based on conformance level of the packet. Use the police KBPS command to
  • D-Link DGS-3130 | Emulator - Page 660
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 63-14 police aggregate This command is used to configure a named aggregate policer as the policy for a traffic class in a policy map. Use the no
  • D-Link DGS-3130 | Emulator - Page 661
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 63-15 police cir This command is actions can be: drop - Packets will be dropped. set-dscp-transmit VALUE - Sets the IP differentiated services code point (DSCP) value and transmits the packet with the new IP DSCP value. set-1p-transmit
  • D-Link DGS-3130 | Emulator - Page 662
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide color of the packet is determined by the initial color mode and create or modify a policy map that can be attached to one or more interfaces as a service policy. Use the no form of this command to delete a policy map. policy-map NAME no
  • D-Link DGS-3130 | Emulator - Page 663
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use the policy-map command to Switch(config-pmap-c)# 63-17 priority-queue cos-map This command is used to define a Class of Service (CoS) to queue map. Use the no form of this command to revert to the default setting.
  • D-Link DGS-3130 | Emulator - Page 664
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline When a packet is received, the packet will be given an internal CoS. highest strict priority queue. This is because the traffic in this queue will be serviced first if the minimal bandwidth of all queues is satisfied. 660
  • D-Link DGS-3130 | Emulator - Page 665
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The configuration of this command can only be attached to a physical port but not a port-channel. That is the minimum guaranteed bandwidth of one CoS
  • D-Link DGS-3130 | Emulator - Page 666
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/5 Switch(config-if)# rate-limit input 2000 4096 Switch(config-if)# 63-20 service-policy This command is used to attach a policy map to the input or output type on an
  • D-Link DGS-3130 | Emulator - Page 667
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# class-map match exit Switch(config-pmap)# exit Switch(config)# interface ethernet 1/0/1 Switch(config-if)# service-policy input cust2-classes Switch(config-if)# 63-21 set This command is used to
  • D-Link DGS-3130 | Emulator - Page 668
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide precedence PRECEDENCE dscp DSCP cos COS cos-queue COS-QUEUE Specifies a new precedence for the packet. The range is from 0 to 7. If the optional keyword
  • D-Link DGS-3130 | Emulator - Page 669
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show class-map [NAME] Parameters NAME (Optional) Specifies the name of the class map. The class map name can be a maximum of 32 alphanumeric characters.
  • D-Link DGS-3130 | Emulator - Page 670
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display the configured aggregated policer.
  • D-Link DGS-3130 | Emulator - Page 671
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display port level QoS configurations.
  • D-Link DGS-3130 | Emulator - Page 672
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show mls qos interface ethernet 1/0/1-2 dscp-mutation Interface ---------eth1/0/1 eth1/0/2 DSCP Mutation Map Mutate Map 1 Mutate Map 2 Switch# This example shows how to display
  • D-Link DGS-3130 | Emulator - Page 673
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show mls qos interface ethernet 1/0/1-2 map dscp-color eth1/0/1 DSCP 0-7 are mapped to green DSCP 8-40 01 01 01 01 01 01 02 02 02 02 20 02 02 02 02 03 03 03 03 03 01 30 03 03 04 04 04 04 04 04 04 04 40 05 05 05 05 05 05 05 05 06 06
  • D-Link DGS-3130 | Emulator - Page 674
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any 16 17 18 19 20 20 21 22 23 24 25 26 27 28 29 30 30 31 32 33 34 35 36 37 38 39 40 40 41 42 43 44 45 46 47 48 49 50 50 51 52 53 54 55 56 57 58 59 60 60 61 62 63 Switch# 63-26 show
  • D-Link DGS-3130 | Emulator - Page 675
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline When the optional keyword Interface is entered, the weight configuration
  • D-Link DGS-3130 | Emulator - Page 676
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show mls qos queueing interface ethernet 1/0/3 Interface: eth1/0/3 wrr bandwidth weights: QID Weights --- ------- 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 0 wdrr bandwidth weights: QID Quantum --- ------- 0 1 1 1 2
  • D-Link DGS-3130 | Emulator - Page 677
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The show policy-map command displays the class policies configured for the policy map. Use the show policymap command to display the class policy configurations of any or all the existing service policy maps. Example This
  • D-Link DGS-3130 | Emulator - Page 678
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide QUANTUM1 ...QUANTUM8 Specifies the quantum (frame length count) value of every queue for weighted round-robin scheduling. Default By default, each quantum value is 1. Command
  • D-Link DGS-3130 | Emulator - Page 679
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage priority scheduling. So the weight of the last queue should be zero while the Differentiate Service is supported. Example This example shows how to configure the queue weight of the WRR scheduling
  • D-Link DGS-3130 | Emulator - Page 680
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 64. Reboot Commands 64-1 reboot This command is used to reboot the Switch. reboot Parameters None. Default None. Command Mode Privileged EXEC Mode. Command Default
  • D-Link DGS-3130 | Emulator - Page 681
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 65. Remote Network MONitoring (RMON) Commands 65-1 rmon collection stats This command is used to enable RMON statistics on the configured interface. Use the no
  • D-Link DGS-3130 | Emulator - Page 682
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide INDEX owner NAME buckets NUM interval SECONDS Specifies the history group table index. The range is from 1 to 65535. Specifies the owner string. The maximum
  • D-Link DGS-3130 | Emulator - Page 683
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide rising-threshold VALUE RISING-EVENT-NUMBER falling- an interface. Switch# configure terminal Switch(config)# rmon alarm 783 1.3.6.1.2.1.2.2.1.12.6 30 delta rising-threshold 20 1 fallingthreshold 10 1 owner Name Switch(config)# 65-4
  • D-Link DGS-3130 | Emulator - Page 684
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline If the log parameter is specified, but not the trap parameter, the created
  • D-Link DGS-3130 | Emulator - Page 685
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the RMON alarm table. Switch# show rmon alarm Alarm index 23, owned by IT Monitors OID: 1.3.6.1.2.1.2.2.1.10.1 every
  • D-Link DGS-3130 | Emulator - Page 686
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show rmon events Event 1, owned by manager1 Description is Errors Event trigger action: log & trap sent to community manager Last triggered time: 13:12:
  • D-Link DGS-3130 | Emulator - Page 687
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show rmon history Index 23, owned by Manager, Data source is eth4/0/2 Interval: 30 seconds Requested buckets: 50, Granted buckets: 50 Sample #1 Received octets: 303595962, Received packets: 357568 Broadcast packets: 3289,
  • D-Link DGS-3130 | Emulator - Page 688
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show rmon statistics Index 32, owned by [email protected], Data Source is eth4/0/3 Received Octets : 234000, Received packets : 9706 Broadcast packets: 2266, Multicast
  • D-Link DGS-3130 | Emulator - Page 689
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 66. Route Map Commands 66-1 match interface This command is used to define a clause to match the route's outgoing interface. Use the no form of
  • D-Link DGS-3130 | Emulator - Page 690
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Route-map Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command in the route map configure mode to define a rule
  • D-Link DGS-3130 | Emulator - Page 691
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to create an IP access list "myacl" first and create a route map entry to match against the next hop based
  • D-Link DGS-3130 | Emulator - Page 692
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 66-5 match metric This command is used to define a clause to match the route's metric. Use the no form of this command to remove the
  • D-Link DGS-3130 | Emulator - Page 693
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline A route map can contain multiple route map entries, which is either a permit entry
  • D-Link DGS-3130 | Emulator - Page 694
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the route map information. Switch# show route-map Route Map mypolicy, permit, sequence 1 Match clauses: ip address myacl
  • D-Link DGS-3130 | Emulator - Page 695
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip access-list Strict-Control Switch(config-ip-acl)# permit 10.1.1.0 0.0.0.255 any Switch(config-ip-acl)# exit Switch(config)#
  • D-Link DGS-3130 | Emulator - Page 696
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip access-list Strict-Control Switch(config-ip-acl)# permit 10.1.1.0 0.0.0.255 any Switch(config-ip-acl)# exit Switch(config)#
  • D-Link DGS-3130 | Emulator - Page 697
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the IP precedence value to 5 (critical) for packets that pass the route map match. Switch# configure terminal Switch(
  • D-Link DGS-3130 | Emulator - Page 698
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 67. Router Advertisement (RA) Guard Commands 67-1 ipv6 nd raguard policy This command is used to create an Router Advertisement (RA) guard policy. The command
  • D-Link DGS-3130 | Emulator - Page 699
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is host. Command Mode RA Guard Policy Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is used
  • D-Link DGS-3130 | Emulator - Page 700
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to create an RA guard policy and matches the IPv6 addresses in the access list named list1. Switch# configure terminal
  • D-Link DGS-3130 | Emulator - Page 701
    Parameters POLICY-NAME DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies the IPv6 RA guard policy name. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline
  • D-Link DGS-3130 | Emulator - Page 702
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 68. Routing Information Protocol (RIP) Commands 68-1 address-family (RIP) This command is used to enter the Router Address Family Configuration (RIP) mode to configure
  • D-Link DGS-3130 | Emulator - Page 703
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this value is 0. Command Mode Router Configuration Mode. Router Address Family Configuration (RIP) Mode. Command Default Level Level: 12. Usage Guideline The
  • D-Link DGS-3130 | Emulator - Page 704
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to configure the distance Mode. Command Default Level Level: 12. Usage Guideline RIP version 1 does not support authentication. This command only takes effect for RIP version 2. Example This example shows
  • D-Link DGS-3130 | Emulator - Page 705
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ip rip authentication text-password PASSWORD no ip rip authentication text-password Parameters PASSWORD Specifies a password string. Default None. Command Mode Interface Configuration Mode. Command
  • D-Link DGS-3130 | Emulator - Page 706
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to specify the version of the receive RIP version for an interface. If not specified,
  • D-Link DGS-3130 | Emulator - Page 707
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 68-8 ip rip v2-broadcast This command is used to enable the sending of version 2 RIP update packets as broadcast packets instead of multicast packets.
  • D-Link DGS-3130 | Emulator - Page 708
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Router Configuration Mode. Router Address Family Configuration (RIP) Mode. Command Default Level Level: 12. Usage Guideline Use this command to specify networks in
  • D-Link DGS-3130 | Emulator - Page 709
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline If you disable the sending of routing updates on an interface, the router will not send multicast RIP packets out through the interface,
  • D-Link DGS-3130 | Emulator - Page 710
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide  The metric of the redistributed route from other protocols to RIP process will be 1 if the metric option is specified as 0. If the default metric
  • D-Link DGS-3130 | Emulator - Page 711
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 68-13 show ip rip database This command is used to display the Routing Information Protocol (RIP) routing database. show ip rip database [IP-ADDRESS
  • D-Link DGS-3130 | Emulator - Page 712
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show ip rip interface Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 12. Usage Guideline This
  • D-Link DGS-3130 | Emulator - Page 713
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 68-15 timers basic This command is used to the flush timer in seconds. The range is from 1 to 65535. Default The default update time: 30 seconds. The default invalid time: 180 seconds. The default flush time: 120 seconds. Command Mode
  • D-Link DGS-3130 | Emulator - Page 714
    Parameters 1 2 DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to only receive and transmit RIP version 1 packets. Specifies to only receive and transmit RIP version 2 packets. Default By default, RIP version 1 and 2 packets
  • D-Link DGS-3130 | Emulator - Page 715
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 69. Routing Information Protocol Next Generation (RIPng) Commands 69-1 clear ipv6 rip This command is used to clear the RIPng process. clear ipv6 rip Parameters
  • D-Link DGS-3130 | Emulator - Page 716
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Router Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to specify the default metric for routes redistributed from other
  • D-Link DGS-3130 | Emulator - Page 717
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ipv6 router rip Switch(config-rtr)# distance 100 Switch(config-rtr)# 69-4 ipv6 rip enable This command is used to
  • D-Link DGS-3130 | Emulator - Page 718
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this value is 1. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The metric refers to the hop count.
  • D-Link DGS-3130 | Emulator - Page 719
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure an IPv6 RIP routing process. Switch# configure terminal Switch(config)# ipv6 router rip Switch(config-rtr)# 69-7 poison-
  • D-Link DGS-3130 | Emulator - Page 720
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide PROTOCOL metric METRIC-VALUE Specifies the protocol whose routes are to be redistributed. It can be one of the following keywords: connected and static. The
  • D-Link DGS-3130 | Emulator - Page 721
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, routing updates are sent. Command Mode Router Configuration Mode. Command Default Level Level: 12. Usage Guideline If this option is disabled, the
  • D-Link DGS-3130 | Emulator - Page 722
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show ipv6 rip IPv6 RIP process, port 521, multicast-group FF02::9 Administrative distance is 71 Maximum paths is 16 Updates every 30 seconds, expire after 180 seconds Garbage collect after 120 seconds Split horizon is on; poison
  • D-Link DGS-3130 | Emulator - Page 723
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 69-12 timers This command is used to the flush timer in seconds. The range is from 1 to 65535. Default The default update time: 30 seconds. The default invalid time: 180 seconds. The default flush time: 120 seconds. Command Mode Router
  • D-Link DGS-3130 | Emulator - Page 724
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default BY default, this option is disabled. Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to turn on
  • D-Link DGS-3130 | Emulator - Page 725
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# debug ipv6 rip interface Switch# The RIPng interface vlan 1 has changed the link state to UP 69-15 debug ipv6 rip packet-transmitting This command is used to turn on the IPv6 RIP packet transmitting debug switch. Use
  • D-Link DGS-3130 | Emulator - Page 726
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to turn on
  • D-Link DGS-3130 | Emulator - Page 727
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#debug ipv6 rip route Switch# Switch# Add a RIPng route to V6 route table dst= 2016:3130:: nexthop= FE80::206:28FF:FED8:FEAC Switch# Switch# 723
  • D-Link DGS-3130 | Emulator - Page 728
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 70. Safeguard Engine Commands 70-1 clear cpu-protect counters This command is used to clear the CPU protect related counters. clear cpu-protect counters {all |
  • D-Link DGS-3130 | Emulator - Page 729
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide FALLING-THRESHOLD the specified percentage, the Safeguard Engine mechanism will initiate. The valid range is from 20 to 100. (Optional) Specifies to set a percentage value
  • D-Link DGS-3130 | Emulator - Page 730
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The reasons of packets that are destined for the CPU can be classified
  • D-Link DGS-3130 | Emulator - Page 731
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The following lists the reference for the supported Host Configuration Domain Name Services Distance Vector Multicast Routing NS/NA/RS/RA Internet Group Management Protocol Link Aggregation Control Protocol Network Time Protocol Open
  • D-Link DGS-3130 | Emulator - Page 732
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show cpu-protect safeguard Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command
  • D-Link DGS-3130 | Emulator - Page 733
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the configured rate limit and
  • D-Link DGS-3130 | Emulator - Page 734
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to display the rate limit and statistics of the safeguard engine. Example This example shows how to display the rate
  • D-Link DGS-3130 | Emulator - Page 735
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 71. Secure File Transfer Protocol (SFTP) Server Commands 71-1 ip sftp server This command is used to enable the SFTP server function. Use the no
  • D-Link DGS-3130 | Emulator - Page 736
    Parameters SECONDS DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the idle timer for the SFTP server. If the SFTP server detects no operation after the duration of idle timer for a specific SFTP session, the Switch will close this SFTP session. The range is from 30 to 600
  • D-Link DGS-3130 | Emulator - Page 737
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command is used to display the SFTP server settings. Example This example shows how to display the global settings of the SFTP
  • D-Link DGS-3130 | Emulator - Page 738
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 72. Secure Shell (SSH) Commands 72-1 crypto key generate This command is used to generate the RSA or DSA key pair. crypto key generate {rsa [
  • D-Link DGS-3130 | Emulator - Page 739
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide key pairs are deleted, the SSH server will not be in service. Example This example shows how to delete the RSA key. respond during the SSH negotiation phase The range is from 30 to 600. Specifies the number of authentication retry attempts.
  • D-Link DGS-3130 | Emulator - Page 740
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to configure the SSH server parameters on the Switch. The authentication retry number specifies the
  • D-Link DGS-3130 | Emulator - Page 741
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# ip ssh server Switch(config)# 72-5 ip ssh service-port This command is used to specify the service port for SSH. Use the no form of this command to revert to the default setting. ip ssh service-
  • D-Link DGS-3130 | Emulator - Page 742
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to display the RSA or DSA public
  • D-Link DGS-3130 | Emulator - Page 743
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the SSH configuration settings. Switch# show ip ssh IP SSH server IP SSH service port SSH server mode Authentication timeout Authentication retries : Enabled : 22 : V2 : 120 secs : 3 times
  • D-Link DGS-3130 | Emulator - Page 744
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Display Parameters SID Ver Cipher Userid Client IP Address A unique number that identifies the SSH session. Indicates the SSH version of this session. The cryptographic /
  • D-Link DGS-3130 | Emulator - Page 745
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The administrator can use this command to specify authentication method for a user. The user name must be a user created by the username command.
  • D-Link DGS-3130 | Emulator - Page 746
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 73. Secure Sockets Layer (SSL) Commands 73-1 no certificate This command is used to delete the imported certificate. no certificate NAME Parameters NAME Specifies the
  • D-Link DGS-3130 | Emulator - Page 747
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide TRUSTPOINT FILE-SYSTEM DIRECTORY FILE-NAME password PASSWORDPHRASE tftp IP-ADDRESS ca local both Specifies the name of the trust-point that is associated with
  • D-Link DGS-3130 | Emulator - Page 748
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# crypto pki import TP1 pem tftp://10.1.1.2/name/msca password abcd1234 both % Importing CA certificate... Destination filename [name/msca.ca]? Reading file from tftp://
  • D-Link DGS-3130 | Emulator - Page 749
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# crypto pki trustpoint TP1 Switch(ca-trustpoint)# primary Switch(ca-trustpoint)# 73-4 crypto pki certificate chain This command is used
  • D-Link DGS-3130 | Emulator - Page 750
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode CA-Trust-Point Configuration Mode. Command Default Level Level: 15. Usage Guideline Use the primary command to specify a given trust-point as primary.
  • D-Link DGS-3130 | Emulator - Page 751
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show crypto pki trustpoints Trustpoint Name : TP1 (primary openflow.prv Switch# 73-7 show ssl-service-policy This command is used to display the SSL service policy. show ssl-service-policy [POLICY-NAME] Parameters POLICY-NAME
  • D-Link DGS-3130 | Emulator - Page 752
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show ssl-service-policy SSL is not configured, the SSL client and server will negotiate the best cipher suite that they both support from the list of available cipher suites. Multiple cipher suites can be specified to be used. Use
  • D-Link DGS-3130 | Emulator - Page 753
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide session-cache-timeout TIME-OUT built-in certificate Guideline This command is used to configure the SSL service policy. Example This example shows how to configure the SSL service policy "ssl-server" which associates the "TP1" trust
  • D-Link DGS-3130 | Emulator - Page 754
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 74. sFlow Commands 74-1 sflow receiver This command is used to configure a receiver for the sFlow agent. Receivers cannot be added to or removed from
  • D-Link DGS-3130 | Emulator - Page 755
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the receiver of index 1 with the owner name of collector1, a timeout value of 86400 seconds, size as 1400
  • D-Link DGS-3130 | Emulator - Page 756
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide An interface can be configured with multiple samplers. If multiple samplers are configured, the configured sampling rate can be different. But the sampling rate of
  • D-Link DGS-3130 | Emulator - Page 757
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/1 Usage Guideline This command is used to display sFlow information. If the MIB is not supported, the MIB version in the sFlow Agent Version string will be null. If the
  • D-Link DGS-3130 | Emulator - Page 758
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show sflow sFlow Agent Version sFlow Agent Address sFlow Agent IPv6 Address : 1.3;D-Link Corporation Inc.;1.00 : 10.90.90.91 : Receivers Information Index Owner Expire Time Current Countdown Time Max Datagram Size Address Port
  • D-Link DGS-3130 | Emulator - Page 759
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Display Parameters sFlow Agent Version sFlow Agent Address sFlow Agent IPv6 Address Index Owner Expire Time Current Countdown Time Max Datagram Size Address Port Datagram
  • D-Link DGS-3130 | Emulator - Page 760
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 75. Simple Mail Transfer Protocol (SMTP) Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The system provides the service to send SYSLOG messages to email receivers via SMTP. Email messages will only be sent
  • D-Link DGS-3130 | Emulator - Page 761
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide self EMAIL-ADDRESS Specifies the email address that which represents the Switch. Default None. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage
  • D-Link DGS-3130 | Emulator - Page 762
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The system provides the service to send SYSLOG messages send a mail for each event immediately. Default By default, this value is 30 minutes. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage
  • D-Link DGS-3130 | Emulator - Page 763
    show smtp DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display
  • D-Link DGS-3130 | Emulator - Page 764
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is used to check the reachability of the SMTP server. An
  • D-Link DGS-3130 | Emulator - Page 765
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 76. Simple Network Management Protocol (SNMP) Commands 76-1 show snmp This command is used to display the SNMP settings. show snmp {community | host | view | group |
  • D-Link DGS-3130 | Emulator - Page 766
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show snmp host Host IP Address SNMP Version Community Name UDP Port : 10.90.90.1 : V1 : public : 162 Total Entries: 1 Switch# This example shows
  • D-Link DGS-3130 | Emulator - Page 767
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to display the SNMP engine ID. Switch#show snmp engineID Local SNMP engineID: 800000ab03f07d6834001000 Switch# 76-2 show snmp user This command
  • D-Link DGS-3130 | Emulator - Page 768
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 76-3 snmp-server community This command is used to configure the community string to access the SNMP. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 769
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 76-4 snmp-server engineID local This command is used to specify the SNMP engine ID on the local device. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 770
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide noauth priv read READ-VIEW write WRITE-VIEW notify NOTIFY-VIEW access IP-ACL-NAME Specifies not to authenticate and not to encrypt the packet.
  • D-Link DGS-3130 | Emulator - Page 771
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# snmp-server view interfacesMibView 1.3.6.1.2.1.2 included Switch(config)# snmp-server group guestgroup v3 auth read interfacesMibView Switch(config)# snmp-server group
  • D-Link DGS-3130 | Emulator - Page 772
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide When specifying to send the trap packets in SNMPv1 or SNMPv2c to a specific host, the specified community string acts as the community string in the
  • D-Link DGS-3130 | Emulator - Page 773
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline Use this command to specify the interface whose IP address will be used as the source address for
  • D-Link DGS-3130 | Emulator - Page 774
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, there is one user. User Name: initial. Group Name: initial. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline
  • D-Link DGS-3130 | Emulator - Page 775
    Default DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide VIEW-NAME Restricted Restricted Restricted Restricted (config)# 76-10 show snmp trap link-status This command is used to display the per interface link status trap state. show snmp trap link-status [interface INTERFACE-ID [, |
  • D-Link DGS-3130 | Emulator - Page 776
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display per interface link up/down trap state. Example This example shows how to display the interface
  • D-Link DGS-3130 | Emulator - Page 777
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use the show snmp-server command to display the SNMP server global state settings. Use the show snmp-server
  • D-Link DGS-3130 | Emulator - Page 778
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the per port trap sending
  • D-Link DGS-3130 | Emulator - Page 779
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The SNMP manager manages a SNMP agent by sending SNMP requests to agents and receiving SNMP responses and notifications from agents. The SNMP server
  • D-Link DGS-3130 | Emulator - Page 780
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide snmp-server enable traps no snmp-server enable linkup (3) trap signifies is generated when the device recognizes that one of the communication links has come up. (Optional) Specifies to control the sending of SNMP linkDown notifications.
  • D-Link DGS-3130 | Emulator - Page 781
    warmstart DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies to control the sending of SNMP warmStart notifications. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level
  • D-Link DGS-3130 | Emulator - Page 782
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to configure the system's location information on the Switch. Example This example shows how to
  • D-Link DGS-3130 | Emulator - Page 783
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 76-19 snmp-server trap-sending disable This command 1/0/8 Switch(config-if)# snmp-server trap-sending disable Switch(config-if)# 76-20 snmp-server service-port This command is used to configure the SNMP UDP port number. Use the no form of
  • D-Link DGS-3130 | Emulator - Page 784
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the SNNP UDP port number on the Switch. The agent will listen to the SNMP request packets on the configured service UDP
  • D-Link DGS-3130 | Emulator - Page 785
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# snmp-server response broadcast-request Switch(config)# 76-22 snmp trap link-status This command is used to enable the notification of link-up and link-down events that occurred on the interface.
  • D-Link DGS-3130 | Emulator - Page 786
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 77. Single IP Management (SIM) Commands 77-1 sim This command is used to enable single IP management. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 787
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide By default, the switch role is Candidate. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline There are 3 roles in the single
  • D-Link DGS-3130 | Emulator - Page 788
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline On the Commander switch, the Candidate switch can be joined to the group and it will be changed to the member switch. The
  • D-Link DGS-3130 | Emulator - Page 789
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide sim interval SECONDS no sim interval Parameters SECONDS Specifies the interval value in seconds. The range is from 30 to 90. Default By default, this value is 30 seconds. Command Mode Global Configuration Mode. Command Default Level
  • D-Link DGS-3130 | Emulator - Page 790
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The single IP management group commander and member will send and receive the SIM message on the SIM management VLAN. Example This example
  • D-Link DGS-3130 | Emulator - Page 791
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide SOURCE-URL DESTINATION-URL member ID. Example This example shows how to download firmware to the member switch 1. Switch# copy sim tftp://10.10.10.58/switch.had firmware member 1 Download firmware 10.10.10.58/ switch.had to
  • D-Link DGS-3130 | Emulator - Page 792
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# copy sim system-log tftp: //10.10.10.58/switchlog member 1 Upload system log from member 1 to 10.10.10.58/switchlog ?(y/n)[n]y ID MAC
  • D-Link DGS-3130 | Emulator - Page 793
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide candidates CANDIDATE-ID members MEMBER-ID Version : VER-2.01 Firmware Version : 1.00.001 Management VLAN : 100 Device Name : Switch MAC Address : F0-7D-68-36-30-B0 Platform : DGS-3130-30TS SIM State : Enabled
  • D-Link DGS-3130 | Emulator - Page 794
    3 Stackable Managed Switch CLI Reference Guide Switch# show sim SIM Version : VER-2.01 Firmware Version : 1.00.001 Device Name : MAC Address : F0-7D-00-36-30-B0 Platform : DGS-3130-30TS SIM State : Enabled Role State : Member Discovery Interval : 30 sec Hold Time : 100 sec CS
  • D-Link DGS-3130 | Emulator - Page 795
    Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show sim candidates Candidate Hold Firmware ID MAC Address Platform Time Version Device Name 1 EE-FF-00-00-12-12 DGS-3130-30TS 90 1.00.001 Total Entries : 1 Switch# This example shows how to display one of the SIM candidate
  • D-Link DGS-3130 | Emulator - Page 796
    Stackable Managed Switch CLI Reference Guide Switch# show sim group 00-02-00-00-08-12 Sim Group Information : [*** Commander Info ***] MAC Address : 00-02-00-00-08-12 Group Name : default Device Name : Firmware Version : 1.00.001 Platform : DGS-3130-30TS Number of Members : 2 Hold Time
  • D-Link DGS-3130 | Emulator - Page 797
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 78. Spanning Tree Protocol (STP) Commands 78-1 clear spanning-tree detected-protocols This command is used to restart the protocol migration. clear spanning-tree detected-
  • D-Link DGS-3130 | Emulator - Page 798
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of interfaces. No 0 Interface --------eth1/0/1 Role State Cost ---- ----- ---- designated forwarding 200000 Priority Link .Port# Type 128.1 p2p Edge ---edge Switch# 78-3 show spanning-tree mst
  • D-Link DGS-3130 | Emulator - Page 799
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide instance INTANCE-ID interface INTERFACE-ID Specifies the instance number. Specifies the interface ID to be displayed. Default None. Command Mode User/Privileged EXEC Mode.
  • D-Link DGS-3130 | Emulator - Page 800
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage tree state : Enabled Port path cost: 0 Port priority: 128 Port Identifier: 128.1 Link type: auto Port fast: edge Guard root: Disabled TCN filter : Disabled Bpdu forward:
  • D-Link DGS-3130 | Emulator - Page 801
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to enable or disable the sending of notification traps. If no optional parameter is specified in the no form of
  • D-Link DGS-3130 | Emulator - Page 802
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide instance INSTANCE-ID vlans VLAN-ID [, | -] no instance INSTANCE-ID [vlans VLAN-ID [, | -]] Parameters INSTANCE-ID VLAN-ID , - Specifies the MSTP instance identifier that is
  • D-Link DGS-3130 | Emulator - Page 803
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode MST Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to configure the name of an MST region. When more
  • D-Link DGS-3130 | Emulator - Page 804
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#configure terminal Switch(config)#spanning-tree mst configuration Switch(config-mst)#revision 2 Switch(config-mst)# 78-10 spanning-tree mst This command is used
  • D-Link DGS-3130 | Emulator - Page 805
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 78-11 spanning-tree mst max-hops This command is used to configure the MSTP maximum hop count. Use the no form of this command
  • D-Link DGS-3130 | Emulator - Page 806
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command the listening to the learning states and learning to forwarding states. The range is from 4 to 30 seconds. Specifies the maximum message age of BPDU. The range is from 6 to 40 seconds.
  • D-Link DGS-3130 | Emulator - Page 807
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the STP timers. Switch# configure terminal Switch(config)# spanning-tree hello-time 1 Switch(config)# spanning-tree forward-time
  • D-Link DGS-3130 | Emulator - Page 808
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide spanning-tree cost COST no spanning-tree cost Parameters COST Specifies the path cost for the port. The range is from 1 to 200000000. Default The
  • D-Link DGS-3130 | Emulator - Page 809
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline This command is used to configure the hello time used in MSTP version for each port. This only
  • D-Link DGS-3130 | Emulator - Page 810
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide a root port. This feature is useful for the service provider to prevent external bridges to a core region of in the STP computation. The port will listen for BPDUs on the link. If the port times out the received superior BPDU, it will
  • D-Link DGS-3130 | Emulator - Page 811
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide spanning-tree link-type {point-to-point | shared} no spanning-tree link-type Parameters point-to-point shared Specifies that the port's link type is point-to-point. Specifies that the port's link type is a shared media connection.
  • D-Link DGS-3130 | Emulator - Page 812
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command  Edge mode - The port will directly change to the spanning-tree forwarding state when a link-up occurs without waiting for the forward-time delay. If the interface receives a BPDU later,
  • D-Link DGS-3130 | Emulator - Page 813
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide  Network mode - The port will remain in the non-port-fast state for three seconds. The port will change to the port-fast state if
  • D-Link DGS-3130 | Emulator - Page 814
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 78-23 spanning-tree priority This command is used to configure the bridge priority. It is only used for RSTP and STP versions. Use the
  • D-Link DGS-3130 | Emulator - Page 815
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Enabling TC filtering on a port is useful for an ISP to prevent the
  • D-Link DGS-3130 | Emulator - Page 816
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the -address This command is used to configure the destination address of the STP BPDU in the service provider site. Use the no form of this command to revert to the default setting. spanning
  • D-Link DGS-3130 | Emulator - Page 817
    Parameters dot1d dot1ad DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to use the Customer Bridge Group Address effect on the VLAN trunk ports, which behave as the NNI ports in the service provider site. This configuration will take effect for all the spanning-tree modes.
  • D-Link DGS-3130 | Emulator - Page 818
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 79. Stacking Commands 79-1 stack This command is used to enable the stacking function. Use the no form of this command to disable the stacking
  • D-Link DGS-3130 | Emulator - Page 819
    support either a 2-port or a 4-port stacking configuration. When the 2-port-10GBaseT stacking configuration is used, a full-duplex speed of up to 40Gbps will be used between two switches.  The DGS-3130-30TS/30S/30PS will use physical ports 25 and 26 for 2-port stacking.  The DGS-3130-54TS/54S/54PS
  • D-Link DGS-3130 | Emulator - Page 820
    Parameters oldunit newunit DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide The current switch identifier on the switch whose identifier is to be changed. The update value of the switch identifier. Default The unit ID is
  • D-Link DGS-3130 | Emulator - Page 821
    value DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the priority assigned to the switch stacking unit. The range is from 0 to 15. The higher number means a higher priority. 0 indicates disabled. Default None.
  • D-Link DGS-3130 | Emulator - Page 822
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display stacking information. 818
  • D-Link DGS-3130 | Emulator - Page 823
    .001/1.01.001 A1 OK 2 DGS-3130-30TS 10 10-62-EB-DE-BA-7B 1.00.001/1.01.001 A1 OK 3 DGS-3130-54PS 10 10-BE-F5-84-ED-E1 1.00.001/1.01.001 A1 OK 4 DGS-3130-54PS 10 10-BE-F5-84-CE-E6 1.00.001/1.01.001 A1 OK 5 DGS-3130-54TS 15 74-DA-DA-33-2D
  • D-Link DGS-3130 | Emulator - Page 824
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 820
  • D-Link DGS-3130 | Emulator - Page 825
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 80. Storm Control Commands 80-1 snmp-server enable traps storm-control This command is used to enable and configure the sending of SNMP notifications for
  • D-Link DGS-3130 | Emulator - Page 826
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide unicast level pps PPS-RISE [PPSLOW] level kbps KBPS-RISE [KBPS-LOW] level LEVEL-RISE [LEVELLOW] action shutdown action drop action none Specifies that when
  • D-Link DGS-3130 | Emulator - Page 827
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 80-3 storm-control polling This command is used to configure the polling interval of received packet counts. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 828
    - broadcast multicast unicast DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies a range of interfaces. No space is allowed before or after the hyphen. (Optional) Specifies to display the current broadcast storm setting. (Optional) Specifies
  • D-Link DGS-3130 | Emulator - Page 829
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show storm-control interface eth1/0/1-2 Polling Interval . Error Disabled: The port is disabled due to a storm. Link Down: The port is physically linked down. Inactive: Indicates that storm control is not enabled for the given
  • D-Link DGS-3130 | Emulator - Page 830
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 81. Super VLAN Commands 81-1 supervlan This command is used to configure the VLAN as a super VLAN. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 831
    Parameters VLAN-ID , - DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the ID of the VLAN as a sub-VLAN. The valid VLAN ID range is from 1 to 4094. (Optional) Specifies a series of VLANs, or separate a
  • D-Link DGS-3130 | Emulator - Page 832
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode VLAN Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is only applicable on a sub-VLAN and is used to configure
  • D-Link DGS-3130 | Emulator - Page 833
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the configuration of all super VLANs. Switch#show supervlan SuperVLAN ID -----------10 SubVLAN ID ---------5 6 7 SubVLAN Status Active Inactive
  • D-Link DGS-3130 | Emulator - Page 834
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 82. Surveillance VLAN Commands 82-1 surveillance vlan This command is used to enable the global surveillance VLAN state and configure the surveillance VLAN. Use the
  • D-Link DGS-3130 | Emulator - Page 835
    Parameters MINUTES DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the aging time of surveillance VLAN. the aging time of surveillance VLAN to 30 minutes. Switch# configure terminal Switch(config)#surveillance vlan aging 30 Switch(config)# 82-3 surveillance vlan enable This
  • D-Link DGS-3130 | Emulator - Page 836
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command is available for physical port and port-channel interface configuration -FF-E0-00-00 FF-FF-FF-F0-00-00 Component Type D-Link Device D-Link Device 832 Description IP Surveillance Device IP Surveillance Device
  • D-Link DGS-3130 | Emulator - Page 837
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide B0-C5-54-00-00-00 F0-7D-68-00-00-00 FF-FF-FF-80-00-00 FF-FF-FF-F0-00-00 D-Link Device D-Link Device IP Surveillance Device IP Surveillance Device Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage
  • D-Link DGS-3130 | Emulator - Page 838
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The surveillance packets arriving at the surveillance VLAN enabled port are marked to the COS specified by the command. The remarking of COS
  • D-Link DGS-3130 | Emulator - Page 839
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show surveillance vlan Surveillance VLAN ID : 1001 Surveillance VLAN CoS : 5 Aging Time : 30 minutes Member Ports : Dynamic Member Ports : Surveillance VLAN OUI : OUI Address 28-10-7B-00-00-00 28-10-7B-20-00-00 B0-C5-54-
  • D-Link DGS-3130 | Emulator - Page 840
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 83. Switch Port Commands 83-1 duplex This command is used to configure the physical port interface's duplex setting. Use the no form of this command
  • D-Link DGS-3130 | Emulator - Page 841
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 83-2 flowcontrol This command is used to configure the flow is determined by both the local port/device and the device connected at the other end of the link, not just by the local device. If the speed is set to the forced mode, the final
  • D-Link DGS-3130 | Emulator - Page 842
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide this command to revert to the default setting. NOTE: 10G does not support speed configurations of 10Mbps and 100Mbps. speed {10 | 100 | 1000 the speed to 1000Mbps and the user must manually set that the port operates as master or slave
  • D-Link DGS-3130 | Emulator - Page 843
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the port operates as master or slave timing. This parameter is only applicable to 10GBASE-T connections. Specifies that for copper ports, it specifies to determine the speed and flow control via auto-negotiation with its link
  • D-Link DGS-3130 | Emulator - Page 844
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 84. System File Management boot. boot image [check] URL Parameters check URL (Optional) Specifies to display the firmware information for the specified file. This information includes the version number and model description. Specifies
  • D-Link DGS-3130 | Emulator - Page 845
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide information Version: 1.00.001 Description: D-Link Corporation TenGigabit Ethernet Switch Switch(config)# This config)# boot image check runtime.wrongswitch.had ERROR: Invalid firmware image. Switch(config)# 84-3 clear running-config This
  • D-Link DGS-3130 | Emulator - Page 846
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to clear the system's configuration retained in DRAM. The configuration
  • D-Link DGS-3130 | Emulator - Page 847
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to clear the system's configuration, including stacking information. The configuration data will revert to the default settings and then save
  • D-Link DGS-3130 | Emulator - Page 848
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Before using the configure replace command, save a backup of the configuration using the copy command or upload the configuration profile to the TFTP server. Example
  • D-Link DGS-3130 | Emulator - Page 849
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide DESTINATION-URL LOCATION If attack-log file in the remote TFTP server, the URL must be prefixed with "tftp: //". To download the firmware image, the user should use the copy tftp: // command to download the file from the TFTP server
  • D-Link DGS-3130 | Emulator - Page 850
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# copy tftp: //10.1.1.254/switch-config.cfg running-config Address of remote host []? 10.1.1.254 Source filename []? switch-config.cfg Destination filename running-config? [y/n]: y
  • D-Link DGS-3130 | Emulator - Page 851
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# copy tftp: //10.1.1.254/image.had flash: image.had ID for the out of band management port. Only Loopback, MGMT and VLAN interfaces are supported in this command. Example This example shows how to download software from the out of
  • D-Link DGS-3130 | Emulator - Page 852
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 84-8 show boot This command is used to display the boot configuration file and the boot image setting. show boot [unit UNIT-ID] Parameters UNIT-
  • D-Link DGS-3130 | Emulator - Page 853
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level : 37947 bytes # DGS-3130-30TS Gigabit Ethernet Switch # Configuration # # Firmware: Build 1.00.001 # Copyright(C) 2017 D-Link Corporation. All rights
  • D-Link DGS-3130 | Emulator - Page 854
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command #show startup-config # DGS-3130-30TS Gigabit Ethernet Switch # Configuration # # Firmware: Build 1.00.001 # Copyright(C) 2017 D-Link Corporation. All rights reserved
  • D-Link DGS-3130 | Emulator - Page 855
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 85. System Log Commands 85-1 clear logging This command is used to delete log messages in the system logging buffer. clear logging Parameters None. Default
  • D-Link DGS-3130 | Emulator - Page 856
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline To enable the logging of system messages, use the logging on command in the global configuration mode. This
  • D-Link DGS-3130 | Emulator - Page 857
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, the severity level is warning (4). Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The system messages can be
  • D-Link DGS-3130 | Emulator - Page 858
    discriminator DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies to filter the message to be sent to the local console based on the discriminator. Default By default, this option is disabled. Command
  • D-Link DGS-3130 | Emulator - Page 859
    Default None. DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline An existing discriminator can be configured. The later setting will overwrite the previous
  • D-Link DGS-3130 | Emulator - Page 860
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide discriminator NAME port UDP-PORT (Optional) Specifies to filter the message to the log server based on discriminator. (Optional) Specifies the UDP port number to
  • D-Link DGS-3130 | Emulator - Page 861
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 23 local7 Local use 7 (local7). Example This example shows how to enable the logging of system messages with a severity higher than warnings to the remote
  • D-Link DGS-3130 | Emulator - Page 862
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the logging of as the source address of the SYSLOG packet. Only Loopback, MGMT and VLAN interfaces are supported in this command. Example This example shows how to configure VLAN 100 as the source
  • D-Link DGS-3130 | Emulator - Page 863
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show logging [all | [REF-SEQ] [+ NN | - NN]] 1, Successful login through Console (Username: Anonymous) #1 2015-03-25 16:35:54 INFO(6) Port eth1/0/1 link up, 1000Mbps FULL duplex Switch# 85-10 show attack-logging This command is used
  • D-Link DGS-3130 | Emulator - Page 864
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show attack-logging unit UNIT-ID [index INDEX] Parameters UNIT-ID index INDEX Specifies the unit on which the attack log messages will be displayed.
  • D-Link DGS-3130 | Emulator - Page 865
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 12. Usage Guideline This command used to delete the attack log messages. Example This example shows
  • D-Link DGS-3130 | Emulator - Page 866
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 86. Time and SNTP Commands 86-1 clock set This command is used to manually clock will be replaced by the new synced clock. Example This example shows how to manually set the software clock to 6:00 p.m. on Jul 4, 2013. Switch# clock set
  • D-Link DGS-3130 | Emulator - Page 867
    DAY DATE MONTH YEAR HH:MM OFFSET DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies that summer time should start and add during summer time. The default value is 60. The range of this offset is 30, 60, 90 and 120. Default By default, this option is disabled. Command Mode
  • D-Link DGS-3130 | Emulator - Page 868
    Parameters DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide + HOURS-OFFSET MINUTES-OFFSET Specifies that time to be added to UTC. Specifies that time to be subtracted from UTC. Specifies the difference in hours
  • D-Link DGS-3130 | Emulator - Page 869
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command also indicates the clock's Source Current Time Time Zone Daylight Saving Time : System Clock : 05:56:45, 2000-01-30 : UTC +00:00 : Disabled Switch# 86-5 show sntp This command is used to display
  • D-Link DGS-3130 | Emulator - Page 870
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show sntp SNTP Status SNTP Poll Interval : can only receive the time from NTP servers; it cannot be used to provide time services to other systems. SNTP typically provides time within 100 milliseconds of the accurate time, but
  • D-Link DGS-3130 | Emulator - Page 871
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure a switch to allow its software clock to be default setting. sntp interval SECONDS no sntp interval Parameters SECONDS Specifies the synchronization interval from 30 to 99999 seconds. 867
  • D-Link DGS-3130 | Emulator - Page 872
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this value is 720 seconds. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline This command is used to
  • D-Link DGS-3130 | Emulator - Page 873
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 87. Time Range Commands 87-1 periodic This command is used to MM to HH:MM Specifies the time of the day, using the format HH:MM (for example, 18:30). weekly WEEK-DAY HH:MM to [WEEK-DAY] HH:MM Specifies the day of the week and the
  • D-Link DGS-3130 | Emulator - Page 874
    Parameters NAME DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies the name of the time-range profile to be displayed. Default None. Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default
  • D-Link DGS-3130 | Emulator - Page 875
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to enter the time range configuration mode before using the
  • D-Link DGS-3130 | Emulator - Page 876
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 88. Traffic Segmentation Commands 88-1 show traffic-segmentation forward This command is used to display the traffic segmentation for some ports or all ports. show
  • D-Link DGS-3130 | Emulator - Page 877
    Parameters INTERFACE-ID , - DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the interfaces to be used. The allowed interfaces include physical port. (Optional) Specifies a series of interfaces or separates a range of interfaces from a previous range.
  • D-Link DGS-3130 | Emulator - Page 878
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 89. Virtual LAN (VLAN) Commands 89-1 acceptable-frame This command is used to set the acceptable types of frames by a port. Use the no form
  • D-Link DGS-3130 | Emulator - Page 879
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is enabled. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline Use this command to enable ingress
  • D-Link DGS-3130 | Emulator - Page 880
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to create the MAC-based VLAN classification entry. The classification entry will be applied to packets received by the Switch.
  • D-Link DGS-3130 | Emulator - Page 881
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# protocol-vlan profile 10 frame-type ethernet2 ether-type 0x86dd Switch(config)# 89-5 protocol-vlan profile (Interface) This command is
  • D-Link DGS-3130 | Emulator - Page 882
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show protocol-vlan {profile [PROFILE-ID [, | -]] | interface [INTERFACE-ID [, | -]]} Parameters profile PROFILE-ID , - interface INTERFACE-ID , - Specifies the protocol group. (Optional) Specifies the protocol group
  • D-Link DGS-3130 | Emulator - Page 883
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show protocol-vlan profile Profile ID ---------1 2 3 Frame-type ----------Ethernet2 Ethernet2 Ethernet2 Ether-type 0x86DD(IPv6) 0x0800(IP) 0x0806(ARP) Total Entries: 3 Switch# 89-7 show
  • D-Link DGS-3130 | Emulator - Page 884
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show vlan VLAN 1 Name : default Tagged Member Ports : Untagged Member Ports : 1/0/1-1/0/8 Total Entries : 1 Switch# This example shows how to display the PVID, ingress checking,
  • D-Link DGS-3130 | Emulator - Page 885
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show vlan mac-vlan MAC Address VLAN ID Priority Status 00-80-cc-00-00-11 101 4 Active 00-11-22-00-00-05
  • D-Link DGS-3130 | Emulator - Page 886
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 89-9 switchport hybrid allowed vlan This command is used to specify the tagged or untagged VLANs for a hybrid port. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 887
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 89-10 switchport hybrid native vlan This command is used to specify the native VLAN ID of a hybrid port. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 888
    dot1q-tunnel DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the port as a dot1q-tunnel port. of a trunk port is to support the switch-to-switch connection. When a port is set to dot1q-tunnnel mode, the port behaves as an UNI port of a service VLAN. When the switch-port
  • D-Link DGS-3130 | Emulator - Page 889
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, all VLANs are allowed. Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline This command only takes effect when
  • D-Link DGS-3130 | Emulator - Page 890
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide frames. When a trunk port works in the untagged mode for a native VLAN, transmitting untagged packet for a native VLAN and tagged packets for all other VLANs
  • D-Link DGS-3130 | Emulator - Page 891
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# vlan 1000-1005 Switch(config-vlan)# 89-15 name This command is used to specify the name of a VLAN. Use
  • D-Link DGS-3130 | Emulator - Page 892
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 90. Virtual LAN (VLAN) Tunnel Commands 90-1 VLAN mapping table. In flow-based tunnel, packets can be tunneled over different service VLANs, and the service VLAN is determined based on the flow-based VLAN mapping rule. The precedence
  • D-Link DGS-3130 | Emulator - Page 893
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 90-2 dot1q inner ethertype This command is tunneling ethertype VALUE no dot1q tunneling ethertype Parameters VALUE Specifies the outer TPID for the service VLAN tag. The value is in the hexadecimal form. The range is 0x1 to 0xFFFF.
  • D-Link DGS-3130 | Emulator - Page 894
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline An 802.1Q tunnel port behaves as an UNI port of a service VLAN. The trunk ports which are tagged members of the service VLAN behave as the NNI
  • D-Link DGS-3130 | Emulator - Page 895
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of VLANs. No space will be dropped. If the VLAN mapping miss drop option is disabled, the port-based service VLAN will be assigned for the unmatched packet. Example This example shows how to configure VLAN
  • D-Link DGS-3130 | Emulator - Page 896
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface ethernet 1/0/2 Switch(config-if)# switchport mode dot1q-tunnel Switch(config-if)# switchport vlan mapping original-vlan 600 resultant-vlan
  • D-Link DGS-3130 | Emulator - Page 897
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide vlan mapping miss drop no vlan mapping miss drop Parameters None. Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default
  • D-Link DGS-3130 | Emulator - Page 898
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline When the trusting dot1q priority option, on a dot1q tunnel port, is enabled the priority of the dot1q VLAN tag in the received packets will be copied to the service VLAN tag. Example This example shows how to configure the
  • D-Link DGS-3130 | Emulator - Page 899
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 90-9 vlan mapping rule This command is used to configure the VLAN mapping rules of the profile. Use the no form of this command to
  • D-Link DGS-3130 | Emulator - Page 900
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to configure the VLAN mapping rules of the profile. If a profile is applied on an interface, the Switch matches the
  • D-Link DGS-3130 | Emulator - Page 901
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure a VLAN Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the service VLAN tag Ethernet type. Example This example shows how to display the 802.1Q TPID setting
  • D-Link DGS-3130 | Emulator - Page 902
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show dot1q ethertype 802.1q inner Ethernet Type is 0x8100 eth1/0/1 802.1q tunneling Ethernet Type is 0x88a8 eth1/0/2 802.1q tunneling Ethernet Type
  • D-Link DGS-3130 | Emulator - Page 903
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show dot1q-tunnel dot1q Tunnel Interface: eth1/0/1 Trust inner priority : Enabled VLAN mapping miss drop : Disabled VLAN mapping profiles : 1, 2, 3 dot1q Tunnel Interface: eth1/0/2 Trust
  • D-Link DGS-3130 | Emulator - Page 904
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show vlan mapping Interface eth1/0/1 eth1/0/1 eth1/0/2 eth1/0/2 eth1/0/3 eth1/0/3 Original VLAN 1 2 10 20 30/3 40/1 Translated VLAN dot1q-tunnel 10 dot1q-tunnel 11 Translate 100 Translate 200 Translate 300 Translate 400/2
  • D-Link DGS-3130 | Emulator - Page 905
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show vlan mapping profile VLAN mapping profile:1 type:ip rule 10 match src-ip 100.1.1.0/24, action dot1q-tunnel outer-vid 100, priority 0 rule 20 match dst-ip 200.1.1.0/24, action dot1q-tunnel outer-vid 200, priority 1 rule 30
  • D-Link DGS-3130 | Emulator - Page 906
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 91. Virtual Router Redundancy Protocol (VRRP) Commands 91-1 snmp-server enable traps vrrp This command is used to enable the VRRP trap function in SNMP.
  • D-Link DGS-3130 | Emulator - Page 907
    Parameters STRING DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the plain text authentication password. This string can be up to 8 characters long. Default By default, no authentication is used. Command Mode Interface Configuration
  • D-Link DGS-3130 | Emulator - Page 908
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command creates a address is the IP address owner. A master will be elected in a group of routers that supports the same virtual routers. Others are the backup routers. The master is responsible for forwarding the
  • D-Link DGS-3130 | Emulator - Page 909
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the priority of the virtual router to 200. Switch#configure terminal Switch(config)#interface vlan 1 Switch(config-if)#
  • D-Link DGS-3130 | Emulator - Page 910
    Parameters VRID INTERVAL DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the virtual router identifier that identifies the VRRP group. The valid range is from 1 to 255. Specifies the time interval between successive advertisements by
  • D-Link DGS-3130 | Emulator - Page 911
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline In preempt mode, a router will take over the master role if it has a better priority than the current
  • D-Link DGS-3130 | Emulator - Page 912
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# configure terminal Switch(config)# interface vlan 1 Switch(config-if)# vrrp 1 shutdown Switch(config-if)# no vrrp 2 shutdown Switch(config-if)# 91-9 vrrp track critical-
  • D-Link DGS-3130 | Emulator - Page 913
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 92. Voice VLAN Commands 92-1 voice vlan This command is used to enable the global voice VLAN state and configure the voice VLAN. Use the
  • D-Link DGS-3130 | Emulator - Page 914
    Parameters MINUTES DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies the aging time of the how to configure the aging time of the voice VLAN to 30 minutes. Switch# configure terminal Switch(config)# voice vlan aging 30 Switch(config)# 92-3 voice vlan enable This command is
  • D-Link DGS-3130 | Emulator - Page 915
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command takes effect for access ports or hybrid ports. Use the voice vlan enable command to enable the voice VLAN function for
  • D-Link DGS-3130 | Emulator - Page 916
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to add a user- Default Level Level: 12. Usage Guideline Use this command to configure automatic learning or manual configuration of voice VLAN member ports. If auto-learning is enabled, the port will
  • D-Link DGS-3130 | Emulator - Page 917
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide When the Switch receives LLDP-MED packets, it remarking of CoS allows the voice VLAN traffic to be distinguished from data traffic in quality of service. Example This example shows how to configure the priority of the voice VLAN to be 7.
  • D-Link DGS-3130 | Emulator - Page 918
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide show voice vlan [interface [INTERFACE-ID [, | -]]] show voice vlan {device | lldp-med device} [interface INTERFACE-ID [, | -]] Parameters interface INTERFACE-ID , device lldp-med device (Optional)
  • D-Link DGS-3130 | Emulator - Page 919
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show voice vlan Voice VLAN ID : 3 Voice VLAN CoS : 5 Aging eth1/0/10 State -------Enabled Enabled Enabled Enabled Disabled Mode ----------Manual Manual Manual Manual Auto/Untag Switch# This example shows how to display the
  • D-Link DGS-3130 | Emulator - Page 920
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Switch# show voice vlan lldp-med device interface eth1/0/1-2 Index : 1 Interface : eth1/0/1 Chassis ID Subtype : MAC Address Chassis ID : 00-E0-BB-00-00-11
  • D-Link DGS-3130 | Emulator - Page 921
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 93. Web Authentication Commands 93-1 web-auth enable This command is used to enable the Web authentication function on the port. Use the no form
  • D-Link DGS-3130 | Emulator - Page 922
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide username-title STRING password-title STRING logout Rights Reserved Switch(config)# web-auth page-element copyright-line 2 title Site: http://support.website.com Switch(config)# 93-3 web-auth success redirect-path This command is used
  • D-Link DGS-3130 | Emulator - Page 923
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide web-auth success redirect-path STRING no web-auth success redirect-path Parameters STRING Specifies the default URL the client Web browser will be redirected
  • D-Link DGS-3130 | Emulator - Page 924
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Web authentication is a feature designed to authenticate a user by using the Web browser when the user is trying
  • D-Link DGS-3130 | Emulator - Page 925
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide If the IPv4 virtual IP is not configured, the IPv4 access cannot start a Web authentication. If the IPv6 virtual IP is not configured, the IPv6
  • D-Link DGS-3130 | Emulator - Page 926
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 94. Weighted Random Early Detection (WRED) Commands 94-1 random-detect This command is used to enable the WRED function. Use the no form of this
  • D-Link DGS-3130 | Emulator - Page 927
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 94-2 random-detect exponential-weight This command is used to configure the WRED exponential weight factor for the average queue size calculation for the queue.
  • D-Link DGS-3130 | Emulator - Page 928
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide red min-threshold VALUE max-threshold VALUE max- on profile 10. Switch# configure terminal Switch(config)# random-detect profile 10 min-threshold 30 max-threshold 50 max-drop-rate 10 Switch(config)# 94-4 show queueing random-detect This
  • D-Link DGS-3130 | Emulator - Page 929
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command will display the WRED configuration. If interface ID
  • D-Link DGS-3130 | Emulator - Page 930
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display the WRED profile setting. Example This example shows how to display the WRED profile 1
  • D-Link DGS-3130 | Emulator - Page 931
    Layer 3 Stackable Managed Switch CLI Reference Guide Appendix A - Password Recovery Procedure This section describes the procedure for resetting passwords on the D-Link DGS-3130 Series switch. Authenticating any user who tries to access networks is necessary and important. The basic authentication
  • D-Link DGS-3130 | Emulator - Page 932
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Appendix B - System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this Switch.
  • D-Link DGS-3130 | Emulator - Page 933
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide server-ip: It indicates the AAA server IP address if authentication method is remote server. username: It indicates the username for authentication. Event description: Login
  • D-Link DGS-3130 | Emulator - Page 934
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters description: server-ip: It indicates the RADIUS server IP address. direction: It indicates the direction for bandwidth control, e.g.: ingress or egress. threshold: The assign
  • D-Link DGS-3130 | Emulator - Page 935
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide BPDU Protection Log Description Event description: Record the event when the BPDU attack happened. Log Message: enter STP BPDU under protection state (mode: <
  • D-Link DGS-3130 | Emulator - Page 936
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide interface-id: Represents the interface number of the MEP. mepdirection: Represents the MEP direction, which can be "inward" or "outward". mepid: Represents the MEPID of
  • D-Link DGS-3130 | Emulator - Page 937
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide vlanid: Represents the VLAN identifier of the : Path and file name on server. Event description: Firmware upgraded unsuccessfully. Log Message: [Unit , ]Firmware upgraded by unsuccessfully (Username: [, IP
  • D-Link DGS-3130 | Emulator - Page 938
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide macaddr : Represent client MAC address. serverIP: Server IP address. pathFile: Path and file name on server. Event description: Firmware uploaded unsuccessfully. Log Message: [Unit , ]Firmware uploaded by
  • D-Link DGS-3130 | Emulator - Page 939
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: [Unit ] Configuration uploaded by unsuccessfully. (Username: [, IP: , MAC: ], Server IP: , File Name: ) Parameters description: unitID: The
  • D-Link DGS-3130 | Emulator - Page 940
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide interface-id: port interface ID. component: DDM threshold type. It can be one of the following types: temperature supply voltage bias current TX power RX
  • D-Link DGS-3130 | Emulator - Page 941
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ipv6address: ipv6 address obtained from a DHCPv6 server. ipif-name: Name of the DHCPv6 client interface. Event description: The ipv6 address obtained from a DHCPv6 server renews
  • D-Link DGS-3130 | Emulator - Page 942
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters description: ipv6address: IPv6 prefix obtained from a delegation router. intf-name: Name of the DHCPv6 client PD interface. Event description: The IPv6 prefix obtained from a
  • D-Link DGS-3130 | Emulator - Page 943
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Description Event description: A unidirectional link has been detected on this port. Log Message: DULD is detected as unidirectional link Event description: manual Switch is issued. Log Message: "Manual Switch is issued
  • D-Link DGS-3130 | Emulator - Page 944
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide InstanceID: Instance ID Event description: Force Switch is issued. Log Display string for the condition of generating critical link event. e.g. OAM disable, Port shutdown, Port link down, Packet overload. Event description: Errored
  • D-Link DGS-3130 | Emulator - Page 945
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: Errored frame period event received(Port < . Warning Interface Log Description Event description: Port link up. Log Message: Port link up, Parameters description: portNum: 1.Interger value;2.Represent
  • D-Link DGS-3130 | Emulator - Page 946
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: Failed to set IPSG entry due to no hardware rule to. Event description: Member port detach from Link Aggregation Group. Log Message: detach from Link Aggregation Group . Parameters description: Ifname: The
  • D-Link DGS-3130 | Emulator - Page 947
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide IfInfo: The interface info. vlanID: The VLAN ID number. Event Description: Port recovered from LBD blocked state under VLAN-based mode. Log Message: IfInfo VID <
  • D-Link DGS-3130 | Emulator - Page 948
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide portNum: The port number. chassisType: chassis ID subtype. Value list: 1. chassisComponent(1) 2. interfaceAlias(2) 3. portComponent(3) 4. macAddress(4) 5. networkAddress(5) 6. interfaceName(6) 7. local(7) chassisID: chassis ID. portType:
  • D-Link DGS-3130 | Emulator - Page 949
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Description Event description: Login through console successfully. Log Message: [Unit , ]Successful login through Console (Username: ) Parameters description: unitID: The unit ID. username:
  • D-Link DGS-3130 | Emulator - Page 950
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters description: username: Represent current login user. ipaddr: Represent client IP address. Event description: SSH session timed out. Log Message: SSH session timed out (Username: <
  • D-Link DGS-3130 | Emulator - Page 951
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Event description: the authorized user number on an interface is below the maximum user limit in a time interval. Log Message: recovers from MAC-
  • D-Link DGS-3130 | Emulator - Page 952
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Event description: Spanning Tree instance created. Log Message: Spanning Tree instance created. (Instance:) Parameters description: InstanceID: Instance ID. Event description: Spanning Tree instance deleted.
  • D-Link DGS-3130 | Emulator - Page 953
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters description: Unit : The unit ID.
  • D-Link DGS-3130 | Emulator - Page 954
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide port: Represents the logical port number. Port Security Log Description Event description: Address full on a port Log Message: MAC address causes port security
  • D-Link DGS-3130 | Emulator - Page 955
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Description Event description: SSH server is enabled. Log Message: SSH server is enabled Event description: SSH server is disabled. Log Message: SSH server is
  • D-Link DGS-3130 | Emulator - Page 956
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters description: Stack_TP_TYPE: The stacking topology type is one of ID. Critical Event description: SIO interface link down. Log Message: SIO interface Unit SIO link down. Parameters description: unitID: Box ID
  • D-Link DGS-3130 | Emulator - Page 957
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Unicast: Storm is resulted by unicast packets, including both known and unknown unicast packets interface-id: The interface ID on which a storm is occurring. Event
  • D-Link DGS-3130 | Emulator - Page 958
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: Broadcast storm is occurring. Parameters description: interface-id: The interface name. Event description: Broadcast storm cleared. Log Message: Broadcast
  • D-Link DGS-3130 | Emulator - Page 959
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: Authentication type mismatch on VR at interface Parameters description: vr-id: VRRP virtual router ID. intf-name: Interface name
  • D-Link DGS-3130 | Emulator - Page 960
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: Failed to add virtual MAC into chip L2 table. Errcode Parameters description: vrrp-mac-addr: VRRP virtual MAC
  • D-Link DGS-3130 | Emulator - Page 961
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters description: vrrp-ip-addr: VRRP virtual IP address vrrp-mac-addr: VRRP virtual MAC address vrrp-errcode: Err code of VRRP protocol behavior. WAC
  • D-Link DGS-3130 | Emulator - Page 962
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide ipaddr: The IP address of HTTP client. Event description: Web session timed out. Log Message: Web session timed out (Username: , IP: ). Parameters description:
  • D-Link DGS-3130 | Emulator - Page 963
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Appendix C - Trap Entries The following table lists all possible trap log entries dnaSessionAuthUserName (5) dDot1xExtNotifyFailReason OID 1.3.6.1.4.1.17 1.14.30.0.1 1.3.6.1.4.1.17 1.14.30.0.2 802.3ah OAM Trap Name dot3OamThresholdEvent
  • D-Link DGS-3130 | Emulator - Page 964
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Authentication Fail Trap Name authenticationFailure Description An authenticationFailure trap signifies that the SNMPv2 entity, acting in an agent role, has received a protocol message that is
  • D-Link DGS-3130 | Emulator - Page 965
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (1) dCfmEventMdIndex (2) dCfmEventMaIndex (3) dCfmEventMepIdentifier dCfmLockCleared This trap is initiated when local MEP exits lock status. Binding objects: (1) dCfmEventMdIndex (2) dCfmEventMaIndex (3) dCfmEventMepIdentifier
  • D-Link DGS-3130 | Emulator - Page 966
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (1) dDoSPrevCtrlAttackType (2) dDosPrevNotiInfoDropIpAddr (3) dDosPrevNotiInfoDropPortNumber ERPS Trap Name dErpsFailuredetectedNotif dErpsFailureClearedNotif dErpsRPLOwnerConflictNotif Description A dErpsFailureNotification is sent
  • D-Link DGS-3130 | Emulator - Page 967
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Binding objects: (1) ifIndex (2) dImpbViolationIpAddrType (3) in an agent role, has detected that the ifOperStatus object for one of its communication links is about to enter the down state from some other state (but not from the
  • D-Link DGS-3130 | Emulator - Page 968
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (1) swLoopDetectPortIndex (2) swVlanLoopDetectVID LLDP-MED Trap Name lldpRemTablesChange lldpXMedTopologyChangeDetecte d Description A lldpRemTablesChange notification is sent when the value of lldpStatsRemTableLastChangeTime changes.
  • D-Link DGS-3130 | Emulator - Page 969
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide dL2FdbMacNotification dL2FdbMacNotificationWithVID This trap indicates the MAC addresses variation in the address table. Binding objects: (1) dL2FdbMac ChangeNotifyInfo This trap indicates the MAC addresses variation in
  • D-Link DGS-3130 | Emulator - Page 970
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Trap Name dPortSecMacAddrViolation Description When the port security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap
  • D-Link DGS-3130 | Emulator - Page 971
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide (1) alarmIndex (2) alarmVariable (3) alarmSampleType (4) alarmValue commander Switch will send this notification when its member generates a link up notification. Binding objects: (1) swSingleIPMSID (2) swSingleIPMSMacAddr (3) ifIndex
  • D-Link DGS-3130 | Emulator - Page 972
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide swSingleIPMSnewRoot swSingleIPMSTopologyChange The commander Switch will send this notification when its member generates a new root notification. Binding objects: (1) swSingleIPMSID (2) swSingleIPMSMacAddr The commander Switch will
  • D-Link DGS-3130 | Emulator - Page 973
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Trap Name dStormCtrlOccurred dStormCtrlStormCleared Description This trap is sent when This trap is sent when the process of upgrading the firmware via SNMP has finished. Binding objects: (1) swMultiImageVersion The
  • D-Link DGS-3130 | Emulator - Page 974
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide vrrpTrapAuthFailure A vrrpAuthFailure trap signifies that a packet has been received from a router whose authentication key or authentication type conflicts with this router's authentication key or authentication
  • D-Link DGS-3130 | Emulator - Page 975
    Managed Switch CLI Reference Guide Appendix D - RADIUS Attributes Assignment The RADIUS Attributes Assignment on the DGS-3130 is used in the following privilege level is configured less than the minimum supported value or greater than the maximum supported value, the privilege level will be ignored.
  • D-Link DGS-3130 | Emulator - Page 976
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide To assign the 802.1p Default Priority by the RADIUS server, the proper parameters should be configured on the RADIUS server. The table below shows
  • D-Link DGS-3130 | Emulator - Page 977
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide will think the VLAN setting string as a "VLAN Name". Then it will check that it can find out a matched VLAN Name. Note: A tag field of
  • D-Link DGS-3130 | Emulator - Page 978
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide Appendix E - IETF RADIUS Attributes Support Remote Authentication Dial-In User Service (RADIUS) attributes carry specific authentication, authorization, information and configuration details for the request and reply. This appendix lists
  • D-Link DGS-3130 | Emulator - Page 979
    DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide 95 NAS-IPv6-Address RADIUS Accounting Attributes: Number 1 4 5 6 8 31 32 40 41 42 43 44 45 46 47 48 49 52 53 61 95 IETF Attribute User-Name NAS-IP-Address NAS-Port Service-Type Framed-IP-Address Calling-Station-ID NAS-Identifier Acct
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386
  • 387
  • 388
  • 389
  • 390
  • 391
  • 392
  • 393
  • 394
  • 395
  • 396
  • 397
  • 398
  • 399
  • 400
  • 401
  • 402
  • 403
  • 404
  • 405
  • 406
  • 407
  • 408
  • 409
  • 410
  • 411
  • 412
  • 413
  • 414
  • 415
  • 416
  • 417
  • 418
  • 419
  • 420
  • 421
  • 422
  • 423
  • 424
  • 425
  • 426
  • 427
  • 428
  • 429
  • 430
  • 431
  • 432
  • 433
  • 434
  • 435
  • 436
  • 437
  • 438
  • 439
  • 440
  • 441
  • 442
  • 443
  • 444
  • 445
  • 446
  • 447
  • 448
  • 449
  • 450
  • 451
  • 452
  • 453
  • 454
  • 455
  • 456
  • 457
  • 458
  • 459
  • 460
  • 461
  • 462
  • 463
  • 464
  • 465
  • 466
  • 467
  • 468
  • 469
  • 470
  • 471
  • 472
  • 473
  • 474
  • 475
  • 476
  • 477
  • 478
  • 479
  • 480
  • 481
  • 482
  • 483
  • 484
  • 485
  • 486
  • 487
  • 488
  • 489
  • 490
  • 491
  • 492
  • 493
  • 494
  • 495
  • 496
  • 497
  • 498
  • 499
  • 500
  • 501
  • 502
  • 503
  • 504
  • 505
  • 506
  • 507
  • 508
  • 509
  • 510
  • 511
  • 512
  • 513
  • 514
  • 515
  • 516
  • 517
  • 518
  • 519
  • 520
  • 521
  • 522
  • 523
  • 524
  • 525
  • 526
  • 527
  • 528
  • 529
  • 530
  • 531
  • 532
  • 533
  • 534
  • 535
  • 536
  • 537
  • 538
  • 539
  • 540
  • 541
  • 542
  • 543
  • 544
  • 545
  • 546
  • 547
  • 548
  • 549
  • 550
  • 551
  • 552
  • 553
  • 554
  • 555
  • 556
  • 557
  • 558
  • 559
  • 560
  • 561
  • 562
  • 563
  • 564
  • 565
  • 566
  • 567
  • 568
  • 569
  • 570
  • 571
  • 572
  • 573
  • 574
  • 575
  • 576
  • 577
  • 578
  • 579
  • 580
  • 581
  • 582
  • 583
  • 584
  • 585
  • 586
  • 587
  • 588
  • 589
  • 590
  • 591
  • 592
  • 593
  • 594
  • 595
  • 596
  • 597
  • 598
  • 599
  • 600
  • 601
  • 602
  • 603
  • 604
  • 605
  • 606
  • 607
  • 608
  • 609
  • 610
  • 611
  • 612
  • 613
  • 614
  • 615
  • 616
  • 617
  • 618
  • 619
  • 620
  • 621
  • 622
  • 623
  • 624
  • 625
  • 626
  • 627
  • 628
  • 629
  • 630
  • 631
  • 632
  • 633
  • 634
  • 635
  • 636
  • 637
  • 638
  • 639
  • 640
  • 641
  • 642
  • 643
  • 644
  • 645
  • 646
  • 647
  • 648
  • 649
  • 650
  • 651
  • 652
  • 653
  • 654
  • 655
  • 656
  • 657
  • 658
  • 659
  • 660
  • 661
  • 662
  • 663
  • 664
  • 665
  • 666
  • 667
  • 668
  • 669
  • 670
  • 671
  • 672
  • 673
  • 674
  • 675
  • 676
  • 677
  • 678
  • 679
  • 680
  • 681
  • 682
  • 683
  • 684
  • 685
  • 686
  • 687
  • 688
  • 689
  • 690
  • 691
  • 692
  • 693
  • 694
  • 695
  • 696
  • 697
  • 698
  • 699
  • 700
  • 701
  • 702
  • 703
  • 704
  • 705
  • 706
  • 707
  • 708
  • 709
  • 710
  • 711
  • 712
  • 713
  • 714
  • 715
  • 716
  • 717
  • 718
  • 719
  • 720
  • 721
  • 722
  • 723
  • 724
  • 725
  • 726
  • 727
  • 728
  • 729
  • 730
  • 731
  • 732
  • 733
  • 734
  • 735
  • 736
  • 737
  • 738
  • 739
  • 740
  • 741
  • 742
  • 743
  • 744
  • 745
  • 746
  • 747
  • 748
  • 749
  • 750
  • 751
  • 752
  • 753
  • 754
  • 755
  • 756
  • 757
  • 758
  • 759
  • 760
  • 761
  • 762
  • 763
  • 764
  • 765
  • 766
  • 767
  • 768
  • 769
  • 770
  • 771
  • 772
  • 773
  • 774
  • 775
  • 776
  • 777
  • 778
  • 779
  • 780
  • 781
  • 782
  • 783
  • 784
  • 785
  • 786
  • 787
  • 788
  • 789
  • 790
  • 791
  • 792
  • 793
  • 794
  • 795
  • 796
  • 797
  • 798
  • 799
  • 800
  • 801
  • 802
  • 803
  • 804
  • 805
  • 806
  • 807
  • 808
  • 809
  • 810
  • 811
  • 812
  • 813
  • 814
  • 815
  • 816
  • 817
  • 818
  • 819
  • 820
  • 821
  • 822
  • 823
  • 824
  • 825
  • 826
  • 827
  • 828
  • 829
  • 830
  • 831
  • 832
  • 833
  • 834
  • 835
  • 836
  • 837
  • 838
  • 839
  • 840
  • 841
  • 842
  • 843
  • 844
  • 845
  • 846
  • 847
  • 848
  • 849
  • 850
  • 851
  • 852
  • 853
  • 854
  • 855
  • 856
  • 857
  • 858
  • 859
  • 860
  • 861
  • 862
  • 863
  • 864
  • 865
  • 866
  • 867
  • 868
  • 869
  • 870
  • 871
  • 872
  • 873
  • 874
  • 875
  • 876
  • 877
  • 878
  • 879
  • 880
  • 881
  • 882
  • 883
  • 884
  • 885
  • 886
  • 887
  • 888
  • 889
  • 890
  • 891
  • 892
  • 893
  • 894
  • 895
  • 896
  • 897
  • 898
  • 899
  • 900
  • 901
  • 902
  • 903
  • 904
  • 905
  • 906
  • 907
  • 908
  • 909
  • 910
  • 911
  • 912
  • 913
  • 914
  • 915
  • 916
  • 917
  • 918
  • 919
  • 920
  • 921
  • 922
  • 923
  • 924
  • 925
  • 926
  • 927
  • 928
  • 929
  • 930
  • 931
  • 932
  • 933
  • 934
  • 935
  • 936
  • 937
  • 938
  • 939
  • 940
  • 941
  • 942
  • 943
  • 944
  • 945
  • 946
  • 947
  • 948
  • 949
  • 950
  • 951
  • 952
  • 953
  • 954
  • 955
  • 956
  • 957
  • 958
  • 959
  • 960
  • 961
  • 962
  • 963
  • 964
  • 965
  • 966
  • 967
  • 968
  • 969
  • 970
  • 971
  • 972
  • 973
  • 974
  • 975
  • 976
  • 977
  • 978
  • 979