D-Link DGS-1510 User Manual

D-Link DGS-1510 Manual

Get D-Link DGS-1510 PDF manuals and user guides View all D-Link DGS-1510 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DGS-1510 manual content summary:

  • D-Link DGS-1510 | User Manual - Page 1
    1
  • D-Link DGS-1510 | User Manual - Page 2
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link
  • D-Link DGS-1510 | User Manual - Page 3
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Table of Contents 1. Introduction ...1 Audience...1 Other Documentation ...1 Conventions...1 Notes, Notices, and Cautions...1 2. Web-based Switch Configuration 19 PoE System ...20 PoE Status ...21 PoE Configuration ...22 PD Alive
  • D-Link DGS-1510 | User Manual - Page 4
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Time Range ...34 4. Management ...36 User Account Settings ...36 Password Encryption...38 Login Method...38 SNMP ...39 SNMP Global Settings ...41 SNMP Linkchange Trap Settings ...
  • D-Link DGS-1510 | User Manual - Page 5
    D-Link Discovery Protocol ...105 5. Layer 2 Features...106 FDB ...106 Static FDB ...106 Unicast Static FDB ...106 Multicast Static FDB...107 MAC Address Table Settings ...107 MAC Address Table ...109 MAC Notification ...110 VLAN ...111 VLAN Configuration Wizard ...111 Create/Configure VLAN ...111
  • D-Link DGS-1510 | User Manual - Page 6
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 802.1v Protocol VLAN ...118 Protocol VLAN Profile ...118 Protocol VLAN Profile Interface ...119 GVRP ...119 GVRP Global ...119 GVRP Port ...120 GVRP Advertise VLAN ...121 GVRP Forbidden VLAN ...122 GVRP Statistics Table ...123
  • D-Link DGS-1510 | User Manual - Page 7
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide LLDP Dot3 TLVs Settings ...170 Default Route ...189 IPv6 Route Table...190 IPMC...191 IP Multicast Global Settings ...191 IP Multicast Forwarding Cache ...191 7. Quality of Service (QoS) ...192 Basic Settings...192 Port Default
  • D-Link DGS-1510 | User Manual - Page 8
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Extended Expert ACL...259 ACL Interface Access Group...271 ACL VLAN Access Map ...272 ACL VLAN Filter ...273 9. Security ...275 Port Security ...275 Port Security Global Settings ...275 Port Security Port Settings ...276 Port
  • D-Link DGS-1510 | User Manual - Page 9
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Advanced Settings ...313 IP-MAC-Port Binding Settings ...313 IP Access Authentication...335 Guest VLAN ...335 Network Access Crypto PKI Trustpoint ...354 SSL Service Policy ...355 Network Protocol Port Protection Settings ...356 10
  • D-Link DGS-1510 | User Manual - Page 10
    Configuration Backup to HTTP ...381 Configuration Backup to TFTP...382 Log Backup ...382 Log Backup to HTTP...382 Log Backup to TFTP ...383 Ping ...384 Trace Route ...386 Language Management ...388 Reset ...388 Reboot System...389 Wizard ...389 Online Help...389 D-Link Support Site ...389 User Guide
  • D-Link DGS-1510 | User Manual - Page 11
    Backup to HTTP ...412 Language Management ...412 Reset...413 Reboot System ...413 Save ...414 Save Configuration ...414 Help ...414 Online Help...415 D-Link Support Site ...415 User Guide ...415 Standard Mode...415 Logout ...415 Appendix A - System Log Entries ...416 Appendix B - Trap Entries ...443
  • D-Link DGS-1510 | User Manual - Page 12
    to configuring and troubleshooting the switch. All the documents are available either from the CD, bundled with this switch, or from the D-Link website. Other documents related to this switch are: • DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide • DGS-1510 Series
  • D-Link DGS-1510 | User Manual - Page 13
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 2. Web-based Switch Configuration Management Options Connecting using the Web Logging onto the Web Smart Wizard Web User Interface (Web UI) Management Options The Switch provides multiple access platforms
  • D-Link DGS-1510 | User Manual - Page 14
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Logging onto the Web UI To access the Web UI, simply open a standard web browser on the management PC, and enter the Switch's default IP address into the address bar of the browser and press the Enter key. NOTE: The default IP
  • D-Link DGS-1510 | User Manual - Page 15
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Smart Wizard After successfully connecting to the Web UI for the first time, the Smart Wizard embedded Web utility will be launched. This wizard will guide the user through basic configuration steps that is essential for first
  • D-Link DGS-1510 | User Manual - Page 16
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Exit button to discard the changes made, exit the Smart Wizard, and continue to the Web UI. Click the Next button to accept the changes made and continue to the next step. Step 2 - System IP Information In this step,
  • D-Link DGS-1510 | User Manual - Page 17
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Gateway Description After selecting the Static option, manually enter the IP address of the default 3 - User Accounts Settings In this step, we can configure the user account settings. This step can only be modified
  • D-Link DGS-1510 | User Manual - Page 18
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Password Description • Encrypted or disable the SNMP feature. Figure 2-6 SNMP Window The fields that can be configured are described below: Parameter SNMP Description Select the Enabled option to enable the SNMP
  • D-Link DGS-1510 | User Manual - Page 19
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Exit button to discard the changes made, exit the Smart Wizard, and continue to the Web UI. Click the Back button to discard
  • D-Link DGS-1510 | User Manual - Page 20
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Web User Interface (Web UI) Areas of the User Interface The Web UI on the Switch can be divided into distinct Areas. Different areas in the Web UI provide different manageability options to simplify configuration and feature
  • D-Link DGS-1510 | User Manual - Page 21
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Area Number AREA 4 Description There is also a search option in this area that can be used to search for specific feature keywords in the Web UI to easily find the link to the set of features. In this area, configuration IP
  • D-Link DGS-1510 | User Manual - Page 22
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Area Number AREA 3 Description In this area, configuration and monitoring window frames are available based on the selections made in Area 2. The status of devices, IP cameras, and NVRs discovered on the switch will also be
  • D-Link DGS-1510 | User Manual - Page 23
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 3. System Device Information System Information Settings Peripheral Settings Port Configuration window after viewing other windows, click the DGS-1510-28XMP link. Figure 3-1 Device Information Window System Information
  • D-Link DGS-1510 | User Manual - Page 24
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: The range is from -100 to 200 degree Celsius. Tick the Default check box to return to the default value. Enter the low threshold value of the warning temperature setting.
  • D-Link DGS-1510 | User Manual - Page 25
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Configuration Port Settings This window is used to view and configure the Switch's port settings. To view the following window, click System > Port Configuration > Port Settings, as shown below: Figure 3-4 Port Settings
  • D-Link DGS-1510 | User Manual - Page 26
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Auto Downgrade Flow Control Duplex Speed the other side of the connection must be set for 1000M Slave. Any other configuration will result in a link down status for both ports. When the Speed is set to Auto, these
  • D-Link DGS-1510 | User Manual - Page 27
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Status This window is used to view the Switch's physical port status and settings. To view the following window, click System > Port Configuration > Port Status, as shown below: Figure 3-5 Port Status Window The fields
  • D-Link DGS-1510 | User Manual - Page 28
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Auto Negotiation This window is used to view detailed port auto-negotiation information. To view the following window, click System > Port Configuration > Port Auto Negotiation, as shown below: Figure 3-7 Port Auto
  • D-Link DGS-1510 | User Manual - Page 29
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Error made. Jumbo Frame This window is used to view and configure the Jumbo Frame size and settings. The Switch supports jumbo frames. Jumbo frames are Ethernet frames with more than
  • D-Link DGS-1510 | User Manual - Page 30
    number and click the Go button to navigate to a specific page when multiple pages exist. PoE (PoE Switches Only) The DGS-1510-28P, DGS-1510-28XMP, and DGS-1510-52XMP switches support Power over Ethernet (PoE) as defined by the IEEE 802.3af and 802.3at. NOTE: The Power over Ethernet (PoE) settings
  • D-Link DGS-1510 | User Manual - Page 31
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide System This window is used to configure the PoE system, and display the The fields that can be configured are described below: Parameter used for this configuration here. Enter the first in, first serviced method. Select this
  • D-Link DGS-1510 | User Manual - Page 32
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Show Detail button, the following table will appear. Figure 3-12 PoE System (Show Detail) Window PoE Status This window is used to configure the description, and display the PoE status of each port. One of the
  • D-Link DGS-1510 | User Manual - Page 33
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide PoE Configuration This window is used to configure the PoE port. To view the following window, click System > PoE > PoE Configuration, as shown below: Figure 3-14 PoE Configuration Window The fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 34
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide PD Alive This window is used to configure the PD Alive Alive Window The fields that can be configured are described below: Parameter Unit From Port / To Port PD Alive State PD IP Address Poll Interval Retry Count Waiting Time
  • D-Link DGS-1510 | User Manual - Page 35
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide PoE Statistics This window is used to display the PoE statistics. To view the following window, click System > PoE > PoE Statistics, as shown below: Figure 3-16 PoE Statistics Window The fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 36
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide PoE Measurement This window is used to display the PoE measurement. To view the following window, click System > PoE > PoE Measurement, as shown below: Figure 3-17 PoE Measurement Window The fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 37
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide PoE LLDP Classification This window is used to display the PoE LLDP Classification. To view the following window, click System > PoE > PoE LLDP Classification, as
  • D-Link DGS-1510 | User Manual - Page 38
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide System Log System Log Settings This window is used to view and configure the Enable, Disabled, and Default. When selecting the Default option, the buffer log's global state will follow the default behavior. Select the severity
  • D-Link DGS-1510 | User Manual - Page 39
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Write Delay Description Enter the interval for periodic writing of the logging buffer to FLASH. This value must be between 0 and 65535 seconds. By default The fields that can be configured for Monitor Log Settings 28
  • D-Link DGS-1510 | User Manual - Page 40
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide System Log Discriminator Settings This window is used to view and configure the system log as shown below: Figure 3-20 System Log Discriminator Settings Window The fields that can be configured are described below: Parameter
  • D-Link DGS-1510 | User Manual - Page 41
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide System Log Server Settings This window is used to view and configure system here. This value must be 514 or between 1024 and 65535. By default, this value is 514. Select the severity value of the type of information that
  • D-Link DGS-1510 | User Manual - Page 42
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Clear Log button to clear the system dissemination services, organize the SNTP subnet of servers and clients, and adjust the system clock in each participant. Clock Settings This window is used to configure the
  • D-Link DGS-1510 | User Manual - Page 43
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. Time Zone Settings This window is used to configure time zones and Daylight Savings Time settings for SNTP. To view the following window, click System > Time and SNTP > Time
  • D-Link DGS-1510 | User Manual - Page 44
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter From: Day of the Week From: Month From: to add during summer time. The default value is 60. The range of this offset is 30, 60, 90 and 120. The fields that can be configured for Date Setting are described below:
  • D-Link DGS-1510 | User Manual - Page 45
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for SNTP Global Settings are 99999 seconds. The default interval is 720 seconds. Click the Apply button to accept the changes made. The fields that can be configured for SNTP Server Setting
  • D-Link DGS-1510 | User Manual - Page 46
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the Delete Periodic button to delete the periodic entry. Click the
  • D-Link DGS-1510 | User Manual - Page 47
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 4. Management User Account Settings Password Encryption Login Method SNMP RMON Telnet/Web Session Timeout DHCP DNS NTP IP Source Interface File System Physical Stacking Virtual Stacking (SIM) D-Link access to configure more
  • D-Link DGS-1510 | User Manual - Page 48
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Privilege Password Type Password Description active user account session will be displayed. Click the Edit button to access and configure the User Privilege settings. Enter a page number and click the Go button to
  • D-Link DGS-1510 | User Manual - Page 49
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Back button to return to the previous page. Password Encryption This window is used to configure whether to save the encryption of the password in the configuration file. To view the following window, click Management
  • D-Link DGS-1510 | User Manual - Page 50
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Enable Password settings are network devices. Use SNMP to configure system features for proper operation, monitor performance, and detect potential problems in the Switch, switch group,
  • D-Link DGS-1510 | User Manual - Page 51
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Managed devices that support been authenticated are ignored (dropped). The default community strings for the Switch used may be encrypted. To read more about how to configure SNMPv3 settings for the Switch read the next section
  • D-Link DGS-1510 | User Manual - Page 52
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The administrator can specify the SNMP to the Switch can be restricted with the Management Station IP Address menu. SNMP Global Settings This window is used to configure the SNMP global settings and trap settings. To view
  • D-Link DGS-1510 | User Manual - Page 53
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Port Link Up Port Link Down Coldstart Warmstart Description Tick this option to control the sending of port link Trap Settings Window The fields that can be configured are described below: Parameter Unit From Port
  • D-Link DGS-1510 | User Manual - Page 54
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide View Table Settings Window The fields that can be configured are described below: Parameter View Name Subtree OID with the community string: • An Access List of IP addresses of SNMP managers that are permitted to use the
  • D-Link DGS-1510 | User Manual - Page 55
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide • Read/write or read-only level permission for Settings Window The fields that can be configured are described below: Parameter Key Type Community Name View Name Access Right IP Access-List Name Description Select the key
  • D-Link DGS-1510 | User Manual - Page 56
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide SNMP Group Table Settings An SNMP Group Table Settings Window The fields that can be configured are described below: Parameter Group Name User-based Security Model Security Level IP Access-List Name Read View Name Write View
  • D-Link DGS-1510 | User Manual - Page 57
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove configured are described below: Parameter Engine ID Description Enter the engine ID string with the maximum of 24 characters. Click the Default button to revert the engine ID to the default
  • D-Link DGS-1510 | User Manual - Page 58
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Group Name SNMP Version SNMP V3 Encryption Auth-Protocol Priv-Protocol IP specified entry. SNMP Host Table Settings This window is used to configure and display the recipient of the SNMP notification. To view the
  • D-Link DGS-1510 | User Manual - Page 59
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter a remote SNMP manger will be encrypted. UDP Port Enter the UDP port number. The default UDP port number of the trap is 162. The range of UDP port numbers is from
  • D-Link DGS-1510 | User Manual - Page 60
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter RMON Falling Alarm Trap shown below: Figure 4-15 RMON Statistics Settings Window The fields that can be configured are described below: Parameter Unit Port Index Owner Description Select the switch unit that
  • D-Link DGS-1510 | User Manual - Page 61
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide RMON History Settings This window is used to configure and display RMON collection history group of statistics. The range is from 1 to 65535. The default value is 50. Enter the time in seconds in each polling cycle. The range
  • D-Link DGS-1510 | User Manual - Page 62
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide RMON Alarm Settings This window is used to configure and display alarm entries to monitor an interface. To view the following window, click Management > RMON > RMON Alarm Settings, as shown below: Figure 4-19 RMON
  • D-Link DGS-1510 | User Manual - Page 63
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide RMON Event Settings This window is used to configure and display event entries. To view the following window, click Management > RMON > RMON Event Settings, as shown below: Figure 4-20 button to return to the previous window. 52
  • D-Link DGS-1510 | User Manual - Page 64
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Telnet/Web This window is used to configure Telnet and Web settings on the Switch. To view the following window, click Management > Telnet/Web, as shown below: Figure 4-22 Telnet/Web Window The fields that can be configured
  • D-Link DGS-1510 | User Manual - Page 65
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Session Timeout This window is used to display and configure 1439 minutes. Enter 0 to disable the timeout. The default value is 0. Select the Default option to use the default value. Enter the Telnet session timeout value here.
  • D-Link DGS-1510 | User Manual - Page 66
    DHCP DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Service DHCP This window is used to configure the DHCP relay service on the Switch. To view the following window, click Management > DHCP > Service DHCP, as shown below: Figure 4-24 Service DHCP Window The fields that
  • D-Link DGS-1510 | User Manual - Page 67
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured Dynamic Host Configuration Protocol (DHCP) allows the Switch to designate IP addresses, subnet masks, default gateways and other IP parameters
  • D-Link DGS-1510 | User Manual - Page 68
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide on its network, or to assign the IP address of an important device (such as a DNS server or the IP address of the default route) to another device on the network. Users also have the ability to bind IP can be configured in DHCP
  • D-Link DGS-1510 | User Manual - Page 69
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Server Pool Settings This window is used to display and configure the DHCP server pool settings. To view the following window, click Management > DHCP > DHCP Server > DHCP Server Pool Settings, as shown below: Figure 4-28
  • D-Link DGS-1510 | User Manual - Page 70
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Option Settings Window The fields that can be configured are described below: Parameter Option Type Description None option to specify a zero-length hexadecimal string. • IP - Enter the IPv4 address(es) in the space(s) provided
  • D-Link DGS-1510 | User Manual - Page 71
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Boot File Domain Name Network (IP/Mask) Next Server Default Router DNS Server NetBIOS Name Server NetBIOS Node Type Lease Description Enter the boot file name
  • D-Link DGS-1510 | User Manual - Page 72
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide a range of excluded addresses, administrators must specify the exact range of addresses previously configured. To view the following window, click Management > DHCP > DHCP Server > DHCP Server Exclude Address, as shown below:
  • D-Link DGS-1510 | User Manual - Page 73
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Client Identifier Description 4-34 DHCP Server Dynamic Binding Window The fields that can be configured are described below: Parameter IP Address Pool Name Description Enter the binding entry IPv4 address here.
  • D-Link DGS-1510 | User Manual - Page 74
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter IP Address Pool Name Description Enter the IPv4 address of the conflict entry to be located or cleared. Enter the DHCP server pool name here. This
  • D-Link DGS-1510 | User Manual - Page 75
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCPv6 Server DHCPv6 Server Pool Settings This window is used to display and configure the DHCPv6 server pool settings. To view the following window, click Management > DHCP > DHCPv6 Server > DHCPv6 Server Pool Settings, as
  • D-Link DGS-1510 | User Manual - Page 76
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured in DHCPv6 Server Pool Configure this value is not specified, then the default valid lifetime will be 2592000 seconds (30 This string can be up to 28 characters long. Enter the Identity
  • D-Link DGS-1510 | User Manual - Page 77
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCPv6 Server Local Pool Settings This window is used to display and configure the DHCPv6 server local pool settings. To view the following window, click Management > DHCP > DHCPv6 Server > DHCPv6 Server Local Pool Settings, as
  • D-Link DGS-1510 | User Manual - Page 78
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide assigned to clients. Use this window to shown below: Figure 4-41 DHCPv6 Server Binding Window The fields that can be configured are described below: Parameter IPv6 Address Description Enter the binding entry IPv6 address to
  • D-Link DGS-1510 | User Manual - Page 79
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCPv6 Server Interface Settings This window is used to display and configure the DHCPv6 server interface settings. To view the following window, click Management > DHCP > DHCPv6 Server > DHCPv6 Server Interface Settings, as
  • D-Link DGS-1510 | User Manual - Page 80
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCPv6 Server Operational Information This window Apply button to accept the changes made. DHCP Relay Pool Settings This window is used to configure and display the DHCP relay pool on a DHCP relay agent. To view the following
  • D-Link DGS-1510 | User Manual - Page 81
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Pool Source Settings Window The fields that can be configured are described below: Parameter Source IP Address Subnet Mask Description Enter the source subnet of
  • D-Link DGS-1510 | User Manual - Page 82
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Edit button under Class, the following window will appear. Figure 4-48 DHCP Relay Pool Class Settings Window The fields that can be configured are described below: Parameter Class Name Description Select
  • D-Link DGS-1510 | User Manual - Page 83
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Relay Information Settings This window is used to configure and display the DHCP relay option to enable or disable the DHCP relay agent to trust the IP DHCP relay information for all interfaces. Select this option to enable
  • D-Link DGS-1510 | User Manual - Page 84
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Relay Information Option Format Settings This window is used to configure circuit ID sub-option. Options to choose from are: • Default - Select to use the default circuit ID sub-option. • User Define - Select to use
  • D-Link DGS-1510 | User Manual - Page 85
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for DHCP Relay Information Option Settings, as shown below: Figure 4-52 DHCP Relay Information Profile Settings Window The fields that can be configured in DHCP Relay Information Option MAC
  • D-Link DGS-1510 | User Manual - Page 86
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide the changes made. The fields that can be configured in DHCP Relay Information Profile Settings are described fill the leading 0. The fill the leading 0 (0) is the default setting. ○ 1~32 - (Optional) Indicates a length option.
  • D-Link DGS-1510 | User Manual - Page 87
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description address will be encapsulated in order in hexadecimal.  sysmac - Indicates the system MAC address. This can be either an ASCII string or a hexadecimal
  • D-Link DGS-1510 | User Manual - Page 88
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Local Relay VLAN This window is used to configure local relay on a VLAN or a group of VLANs. To view the following window, click Management > DHCP > DHCP Relay > DHCP Local Relay VLAN choose from are Default, CID With User
  • D-Link DGS-1510 | User Manual - Page 89
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter IPv6 DHCP Relay Remote ID Option Description • fields that can be configured are described below: Parameter Interface VLAN Destination IPv6 Address Output Interface VLAN Description Enter the VLAN from 1 to 4094
  • D-Link DGS-1510 | User Manual - Page 90
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Auto Configuration This window is used to configure the DHCP auto-configuration function. To view the following window, click Management > DHCP > DHCP Auto Configuration, as shown below: Figure 4-56 DHCP Auto Configuration
  • D-Link DGS-1510 | User Manual - Page 91
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide domain name service is often supplied by a DHCP or BOOTP server, or can be entered manually and configured into the Name Server Settings This window is used to configure and display the IP address of a domain name server. To view
  • D-Link DGS-1510 | User Manual - Page 92
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: 4-59 DNS Host Settings Window The fields that can be configured are described below: Parameter Host Name IP Address IPv6 Address Description Enter the host name of the
  • D-Link DGS-1510 | User Manual - Page 93
    NTP DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NTP Global Settings This window is used to view and configure the Network Time This value must be between 1 and 15. Select the Default option to use the default value. Enter the NTP maximum amount of associations here.
  • D-Link DGS-1510 | User Manual - Page 94
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. NTP Server Settings This window is used to view and configure Window The fields that can be configured are described below: Parameter IP Address IPv6 Address Version Key ID
  • D-Link DGS-1510 | User Manual - Page 95
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NTP Peer Settings This window is used to view and configure the NTP peer settings. To view the following window, click Management > NTP > NTP Peer Settings, as shown below: Figure 4-62 NTP Peer Settings Window The
  • D-Link DGS-1510 | User Manual - Page 96
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NTP Access Group Settings This window is used to view and configure the NTP Group Settings Window The fields that can be configured are described below: Parameter Default IP Address Netmask IPv6 Address IPv6 Mask Ignore No
  • D-Link DGS-1510 | User Manual - Page 97
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NTP Key Settings This window is used to view and configure the NTP key settings. To view the following window, click Management > NTP > NTP Key Settings, as shown below: Figure 4-64 NTP Key Settings Window The
  • D-Link DGS-1510 | User Manual - Page 98
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NTP Interface Settings This window is used to view and configure the NTP interface settings. To view the following window, click Management > NTP > NTP Interface Settings, as shown below: Figure 4-65 NTP Interface Settings
  • D-Link DGS-1510 | User Manual - Page 99
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Detail button, next to the specified , as shown below: Figure 4-68 NTP Status Window IP Source Interface This window is used to configure the IP source interface settings. To view the following window, click Management
  • D-Link DGS-1510 | User Manual - Page 100
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Source Interface State Interface Type VID (1-4094) Description Select to Enable or Disable the source interface feature's global state here. After
  • D-Link DGS-1510 | User Manual - Page 101
    with the indicated configuration file. Click the Apply button to initiate the copy. Click the Cancel button the discard the process. Physical Stacking The Switch supports switch stacking, where a set of six switches can be combined and managed by one IP address through Telnet, the Web UI
  • D-Link DGS-1510 | User Manual - Page 102
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide these ports together using fiber cables or Direct Attach Cables (DAC) in one of two possible topologies. • Duplex Chain -The Duplex Chain topology stacks switches together in a chain-link format. Using this method, data transfer
  • D-Link DGS-1510 | User Manual - Page 103
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-74 Switches stacked in a Duplex Ring Within each to remaining switches in the switch stack. The Primary Master can be configured manually by assigning the Switch the highest priority (a lower number denotes a higher
  • D-Link DGS-1510 | User Manual - Page 104
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide configurations of the Primary Master. Once these steps have been completed, the switch stack will enter a normal operating mode. Stack Switch Swapping The stacking feature of the Switch supports ports links is and IP address
  • D-Link DGS-1510 | User Manual - Page 105
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-75 Physical Stacking Window The fields that can be configured Apply button to accept the changes made. Virtual Stacking (SIM) D-Link Single IP Management (SIM) is a concept that will stack switches together over
  • D-Link DGS-1510 | User Manual - Page 106
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide • SIM can eliminate any specialized cables for stacking connectivity and remove the distance barriers that typically limit your topology options when using other stacking technology. Switches using D-Link Single IP Management (
  • D-Link DGS-1510 | User Manual - Page 107
    Web UI Reference Guide After configuring one switch to operate as the CS of a SIM group, additional DGS-1510 Series switches may join the group by manually configuring the Switch to be a MS. The CS will then serve as the in band entry point for access to the MS. The CS's IP address will become
  • D-Link DGS-1510 | User Manual - Page 108
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Single IP Settings This window is used to configure the SIM settings. The Switch is set as a Candidate (CaS) as the factory default configuration and Single IP Management is disabled. To view the following window, click
  • D-Link DGS-1510 | User Manual - Page 109
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Management VLAN Description Enter the single IP management message VLAN ID. Click the Apply button to accept the changes made. After enabling the Switch to be a Commander Switch (CS), the Single IP Management
  • D-Link DGS-1510 | User Manual - Page 110
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Preference On the File menu, select Preference to configure the display properties for the SIM topology map. Figure 4-78 Preference The fields that can be configured are described below: Parameter Interval Show All Show
  • D-Link DGS-1510 | User Manual - Page 111
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Remove from Group Select a Member Switch (MS) from the list and then select Remove from Group on the Group menu to remove the selected MS from the SIM group. Device Configure Select a device from the list and then select
  • D-Link DGS-1510 | User Manual - Page 112
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide This window will display how the devices within Tool Tips In the Topology view window, the mouse plays an important role in configuration and in viewing device information. Point to a specific device in the Topology window to
  • D-Link DGS-1510 | User Manual - Page 113
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Righ-Click Right-click a device to allow the Device Name of the Switches in the SIM group configured. If the device is not configured with a name, it will be given the name default and tagged with the last six digits of the
  • D-Link DGS-1510 | User Manual - Page 114
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Model MAC Firmware Upgrade, as shown below: Figure 4-88 Firmware Upgrade Window The fields that can be configured are described below: Parameter TFTP Server IP Path\Filename Description Enter the TFTP server IP
  • D-Link DGS-1510 | User Manual - Page 115
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Configuration File Backup/Restore This window is used to upgrade configuration fields that can be configured are described below: Parameter TFTP Server IP Path\Filename Description Enter the TFTP server IP address. Enter the
  • D-Link DGS-1510 | User Manual - Page 116
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide D-Link Discovery Protocol This window is used to configure and display D-Link Discovery Protocol (DDP). To view the following window, click Management > D-Link Discovery Protocol, as shown below: Figure 4-91 D-Link Discovery
  • D-Link DGS-1510 | User Manual - Page 117
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 5. Layer 2 Features FDB VLAN STP ERPS (G.8032) Loopback Detection Link Aggregation L2 Multicast Control LLDP FDB Static FDB Unicast Static FDB This window is used to view and configure the static unicast forwarding settings on
  • D-Link DGS-1510 | User Manual - Page 118
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Multicast Static FDB This window is used to view and configure the multicast static FDB for this configuration here. Select the appropriate port range used for the configuration here. Enter the VLAN ID of the VLAN the
  • D-Link DGS-1510 | User Manual - Page 119
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Aging Time Aging Destination Hit Description Enter the MAC address table's aging time value here. This value must be between 10
  • D-Link DGS-1510 | User Manual - Page 120
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide MAC Address Table This window is used to be used for this configuration here. Enter the VLAN ID that will be used for this configuration here. Enter the MAC address that will be used for this configuration here. Click the Clear
  • D-Link DGS-1510 | User Manual - Page 121
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide MAC Notification This window is used to view and configure MAC notification. between notifications. This value must be between 1 and 2147483647 seconds. By default, this value is 1 second. Enter the maximum number of entries
  • D-Link DGS-1510 | User Manual - Page 122
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the MAC Notification History tab, the following page will be available. Figure 5-7 MAC Notification (MAC Notification History) Window A list of MAC notification messages will be displayed. VLAN VLAN Configuration
  • D-Link DGS-1510 | User Manual - Page 123
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Create VLAN After selecting the Create VLAN option and clicking the Next button, the following window will appear. Figure 5-9 VLAN Configuration Wizard (Create VLAN) Window The fields that can be configured are described below
  • D-Link DGS-1510 | User Manual - Page 124
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Configure VLAN After selecting the Configure VLAN option and clicking the Next button, the following window will appear. Figure 5-11 VLAN Configuration Wizard (Configure VLAN) Window The fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 125
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 802.1Q VLAN This window is used to view and configure the VLAN settings on this switch. To view the following window, click L2 Features > VLAN > 802.1Q VLAN, as shown below: Figure 5-13 802.1Q VLAN Window The fields that can
  • D-Link DGS-1510 | User Manual - Page 126
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide VLAN Interface VLAN Interface Settings This window is used to view and configure VLAN interface settings. To view the following window, click L2 Features > VLAN > VLAN Interface, as shown below: Figure 5-14 VLAN Interface
  • D-Link DGS-1510 | User Manual - Page 127
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After click the Edit button, the following window will appear. This is a dynamic window that will change when a different VLAN Mode was selected. When Access was selected as the VLAN Mode, the following page will appear. Figure
  • D-Link DGS-1510 | User Manual - Page 128
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Acceptable Frame Ingress Checking Native VLAN VID Action Add Mode Allowed VLAN Range Clone Unit From Port / To Port Description Select the acceptable frame behavior option here. Options to choose from are Tagged Only
  • D-Link DGS-1510 | User Manual - Page 129
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Action Allowed VLAN Range Clone Unit From Port / To Port Description Select the action that will be taken here. Options to choose from are All, Add, Remove, Except, and Replace. Enter the allowed VLAN range
  • D-Link DGS-1510 | User Manual - Page 130
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Frame Type Ether Type Description be used for this configuration here. Select the ID of the protocol group. Enter the VLAN ID of the Protocol VLAN. Select the priority of the Protocol VLAN. Click the Apply button
  • D-Link DGS-1510 | User Manual - Page 131
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Global GVRP State Dynamic VLAN Creation Description Select this option to enable or disable the global GVRP state here. Select this option to enable or disable
  • D-Link DGS-1510 | User Manual - Page 132
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide GVRP Advertise VLAN This window is used to view and configure the GVRP advertised VLAN settings. To view the following window, click L2 Features > VLAN > GVRP > GVRP Advertise VLAN, as shown below: Figure 5-24 GVRP Advertise
  • D-Link DGS-1510 | User Manual - Page 133
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide GVRP Forbidden VLAN This window is used to view and configure the GVRP forbidden VLAN settings. To view the following window, click L2 Features > VLAN > GVRP > GVRP Forbidden VLAN, as shown below: Figure 5-25 GVRP Forbidden
  • D-Link DGS-1510 | User Manual - Page 134
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide GVRP Statistics Table This window is used to display GVRP statistics information. To view the following window, click L2 Features > VLAN > GVRP > GVRP Statistics Table, as shown below: Figure 5-26 GVRP Statistics Table Window
  • D-Link DGS-1510 | User Manual - Page 135
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Asymmetric VLAN State Description Select this option to enable or disable the asymmetric VLAN function Click the Apply button to accept the changes made. MAC
  • D-Link DGS-1510 | User Manual - Page 136
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide L2VLAN Interface Description This window is used to display and configure the Layer 2 VLAN interface description. To view the following window, click L2 Features > VLAN > L2VLAN Interface Description, as shown below: Figure 5-
  • D-Link DGS-1510 | User Manual - Page 137
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NOTE: The same PC, or PCs connected to the same LAN port on the Switch, cannot simultaneously manage the Switch and the IP cameras connected to the Switch. To view the following window, click L2 Features > VLAN > Auto
  • D-Link DGS-1510 | User Manual - Page 138
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description by snooping RTSP, HTTP, configure the user-defined surveillance device OUI and display the surveillance VLAN information. To view the following window, click L2 Features > VLAN > Auto Surveillance VLAN
  • D-Link DGS-1510 | User Manual - Page 139
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Auto Surveillance VLAN Summary tab, the following page will appear. Figure 5-32 Auto Surveillance VLAN Summary Window The fields that can be configured are described below: Parameter Unit Description
  • D-Link DGS-1510 | User Manual - Page 140
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After click the More Detail button, the following window will appear. Figure 5-34 ONVIF IP-Camera Information (More Detail) Window After click the Edit button, the following window will appear. Figure 5-35 ONVIF IP-Camera
  • D-Link DGS-1510 | User Manual - Page 141
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit Description Select the switch unit that will be used in the display here. Click the IP Address hyperlink to connect to the Web Interface of the NVR. Click
  • D-Link DGS-1510 | User Manual - Page 142
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click L2 Features > VLAN > Voice VLAN > Voice VLAN Global, as shown below: Figure 5-39 Voice VLAN Global Window The fields that can be configured are described below: Parameter Voice VLAN State
  • D-Link DGS-1510 | User Manual - Page 143
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Voice VLAN Port This window is used to show the ports voice VLAN information. To view the following window, click L2 Features > VLAN > Voice VLAN > Voice VLAN Port, as shown below: Figure 5-40 Voice VLAN Port Window The fields
  • D-Link DGS-1510 | User Manual - Page 144
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Voice VLAN OUI This window is used to configure the user-defined voice traffic's OUI. The OUI is used to identify the voice traffic. There are a number of pre-defined OUIs. The user can
  • D-Link DGS-1510 | User Manual - Page 145
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit Description Select the switch unit that will be used for this configuration here. Voice VLAN LLDP-MED Device This window displays the voice VLAN LLDP-MED
  • D-Link DGS-1510 | User Manual - Page 146
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide • A 4094-element table (defined here as a VID List in the MST Configuration Identification window), which will associate each of the possible 4094 VLANs supported by the Switch for a given instance. To utilize the MSTP function
  • D-Link DGS-1510 | User Manual - Page 147
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide RSTP is capable of a more rapid transition to a forwarding state - it no longer relies on timer configurations - RSTP compliant bridges are sensitive to feedback from other RSTP compliant bridge links. Ports do not need to wait
  • D-Link DGS-1510 | User Manual - Page 148
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The field that can be configured for Spanning Tree State is described below: Parameter Spanning Tree State Description Select this option to enable or disable the STP global state here. Click
  • D-Link DGS-1510 | User Manual - Page 149
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter TX Hold Count Max Hops Description Enter the transmit hold count value here. This value must be between 1 and 10 times. By default . By default, this value is 20 hops. used to view and configure the STP port settings.
  • D-Link DGS-1510 | User Manual - Page 150
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Guard Root Link Type Port Fast TCN Filter BPDU Forward Priority Hello Time Description Select to enable or disable the guard root function. Select the link type option here. Options to choose from are Auto, P2P, and
  • D-Link DGS-1510 | User Manual - Page 151
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide and 65535. By default, this value is 0. This value, along with the Configuration Name, identifies the MSTP region configured on the Switch specify the VID range from configured VLANs set on the Switch. Click the Apply button to accept
  • D-Link DGS-1510 | User Manual - Page 152
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide STP Instance This window is used to view and configure the STP instance settings. To view the following window, click L2 Features > STP > STP Instance, as shown below: Figure 5-47 STP Instance Window Click the
  • D-Link DGS-1510 | User Manual - Page 153
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ERPS (G.8032) For more information, refer to Appendix E - ERPS Information. ERPS This window is used to view and configure Ethernet Ring Protection Switching (ERPS) settings. To view the following window, click L2 Features >
  • D-Link DGS-1510 | User Manual - Page 154
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Port0 Port1 Description Select the None radio button to revert this parameter to the default that can be configured are described below: Parameter Description R-APS Channel VLAN Inclusion VLAN List Description
  • D-Link DGS-1510 | User Manual - Page 155
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter MEL Profile Name RPL Port RPL Owner Activate Description Select the checkbox and enter the ring MEL value of the ERP instance here. This value must be between 0 and 7. The configured MEL value of all ring nodes that
  • D-Link DGS-1510 | User Manual - Page 156
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ERPS Profile This window is used to view and configure the Ethernet Ring G.8032 profile associated with the same profile protect the same set of VLANs, or the VLANs protected by one instance are a subset of LANs protected by
  • D-Link DGS-1510 | User Manual - Page 157
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Guard Timer Hold-Off Timer WTR Timer Description Select the checkbox and enter the guard timer value here. This value must be between 10 and 2000 milliseconds. By default, this value is 500 milliseconds. Select the
  • D-Link DGS-1510 | User Manual - Page 158
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Interval Traps State Action Address Type Description Enter the interval in seconds that the device will transmit all the CTP (Configuration Traffic will be blocked on the specific VLAN in the VLANbased mode. • None -
  • D-Link DGS-1510 | User Manual - Page 159
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Link Aggregation Understanding Port Trunk Groups Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The Switch supports up to 32 port trunk groups with 1 to 8 ports in
  • D-Link DGS-1510 | User Manual - Page 160
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The Spanning Tree Protocol will treat a link aggregation group as a single link, on the switch level. On the port level, the STP will use the port parameters of the Master Port in the calculation of port cost
  • D-Link DGS-1510 | User Manual - Page 161
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description group type is static. be available. Figure 5-58 Port Channel Window The fields that can be configured for Port Channel Description are described below: Parameter Description Description Enter the
  • D-Link DGS-1510 | User Manual - Page 162
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide L2 Multicast Control IGMP Snooping Internet the changes made. The fields that can be configured for VLAN Status Settings are described below: Parameter VID Description Enter a VLAN ID from 1 to 4094, and select to enable
  • D-Link DGS-1510 | User Manual - Page 163
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Show Detail button to see the detail information of the specific VLAN. Click the Edit button to re-configure the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple
  • D-Link DGS-1510 | User Manual - Page 164
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured of IGMP hosts that is allowed on the VLAN. Select this option to enable or disable or disable the proxy-reporting function. Enter the source IP of proxy reporting. This is available when Enabled
  • D-Link DGS-1510 | User Manual - Page 165
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IGMP Snooping Groups Settings This window is used to configure and view the IGMP the radio button and enter a VLAN ID of the multicast group. Click the radio button and enter an IP multicast group address. Displays the filter
  • D-Link DGS-1510 | User Manual - Page 166
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Exp (sec) Description • EX (Exclude) specified entry. The fields that can be configured for IGMP Snooping Mrouter Table are described below: Parameter VID Description Enter a VLAN ID between 1 and 4094. Click the
  • D-Link DGS-1510 | User Manual - Page 167
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IGMP Snooping Statistics Settings This VLAN, and Port. Enter a VLAN ID between 1 and 4094. This is available when VLAN is selected in the Statistics drop-down list. Select the switch unit that will be used for this configuration
  • D-Link DGS-1510 | User Manual - Page 168
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide in the multicast routing table records the port, the VLAN ID, and the associated multicast IPv6 multicast group address this message is sent by the router to ask if any link is requesting multicast data. There are two types of MLD
  • D-Link DGS-1510 | User Manual - Page 169
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide MLD Snooping Settings This window is used to configure the MLD snooping Detail button to see the detail information of the specific VLAN. Click the Edit button to re-configure the specific entry. Enter a page number and click the
  • D-Link DGS-1510 | User Manual - Page 170
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Show Detail button, the following window will appear. Figure 5-66 MLD Snooping VLAN Parameters Window The window displays the detail information about MLD snooping VLAN. Click the Modify button to edit the
  • D-Link DGS-1510 | User Manual - Page 171
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Report Suppression Suppression Time The fields that can be configured for MLD Snooping Static Groups Settings are described below: Parameter VID Group Address Description Enter a VLAN ID of the multicast group.
  • D-Link DGS-1510 | User Manual - Page 172
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Unit From Port / To Port VID Group Address Description Select the switch unit that will be used for this configuration here. Select the appropriate port range used for the configuration here. Click the radio button
  • D-Link DGS-1510 | User Manual - Page 173
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for MLD Snooping Mrouter Settings are described below: Parameter VID Configuration Unit From Port / To Port Description Enter a VLAN ID between 1 and 4094. Select the port configuration.
  • D-Link DGS-1510 | User Manual - Page 174
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter VID Unit From Port / To Port Description Enter a VLAN ID between 1 and 4094. This is available when VLAN is selected in the Statistics drop-down list. Select the switch unit that will be used for this configuration
  • D-Link DGS-1510 | User Manual - Page 175
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description • Forward Unregistered - Specifies that registered multicast packets will be forwarded based on the forwarding table and all unregistered multicast packets will be flooded based on the VLAN to configure
  • D-Link DGS-1510 | User Manual - Page 176
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter LLDP Forward State LLDP the Apply button to accept the changes made. The fields that can be configured for LLDP-MED Configuration are described below: Parameter Fast Start Repeat Count Description Enter the LLDP-
  • D-Link DGS-1510 | User Manual - Page 177
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide LLDP Port Settings This window is used to configure the LLDP port settings. To view transmit and receive LLDP frames. This is the default option. • Disabled - The local LLDP agent can neither transmit nor receive LLDP frames. Select the
  • D-Link DGS-1510 | User Manual - Page 178
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Action Address Description Select the action that will be taken here. Options to choose from are Remove and Add. Enter the IP four optional data types that can be configured for an individual port or group of ports
  • D-Link DGS-1510 | User Manual - Page 179
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide mandatory data types cannot be disabled. There are also below: Figure 5-75 LLDP Basic TLVs Settings Window The fields that can be configured are described below: Parameter Unit From Port / To Port Port Description System Name
  • D-Link DGS-1510 | User Manual - Page 180
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide LLDP Dot1 TLVs Settings LLDP Dot1 TLVs are organizationally specific TLVs, which are defined in IEEE 802.1 and used to configure be configured are described below: Parameter Unit From Port / To Port Port VLAN Protocol VLAN VLAN
  • D-Link DGS-1510 | User Manual - Page 181
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide LLDP Dot3 TLVs Settings This window is used to configure configured are described below: Parameter Unit From Port / To Port MAC/PHY Configuration/Status Link supplied over the link for connected non-powered systems. The Power
  • D-Link DGS-1510 | User Manual - Page 182
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the shown below: Figure 5-78 LLDP-MED Port Settings Window The fields that can be configured are described below: Parameter Unit From Port / To Port Notification Capabilities Network Policy PSE
  • D-Link DGS-1510 | User Manual - Page 183
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the as shown below: Figure 5-79 LLDP Statistics Information Window The fields that can be configured are described below: Parameter Unit Port Description Select the switch unit that will be
  • D-Link DGS-1510 | User Manual - Page 184
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide LLDP Local Port Information This window shown below: Figure 5-80 LLDP Local Port Information Window The fields that can be configured are described below: Parameter Unit Port Description Select the switch unit that will be
  • D-Link DGS-1510 | User Manual - Page 185
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Back button to return to shown below: Figure 5-83 LLDP Neighbor Port Information Window The fields that can be configured are described below: Parameter Unit Port Description Select the switch unit that will be
  • D-Link DGS-1510 | User Manual - Page 186
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Show Detail button, the following window will appear. Figure 5-84 LLDP Neighbor Port Information - Show Detail Window To view more details about,
  • D-Link DGS-1510 | User Manual - Page 187
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 6. Layer 3 Features ARP Gratuitous ARP UDP Helper IPv4 Interface IPv4 Static/Default Route IPv4 Route Table IPv6 Interface IPv6 Neighbor IPv6 Static/Default Click the Edit button to re-configure the specific entry. Click the
  • D-Link DGS-1510 | User Manual - Page 188
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Static ARP This window is used to view and configure the static ARP settings. To view the following window, click L3 Features > ARP > Static ARP, as shown below: Figure 6-2 Static ARP Window The fields that can be configured
  • D-Link DGS-1510 | User Manual - Page 189
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Local Proxy ARP State Description Select to enable or disable the local proxy ARP state here. This local proxy ARP function allows the Switch to respond to the proxy ARP, if the source IP and destination IP are in
  • D-Link DGS-1510 | User Manual - Page 190
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Gratuitous ARP This window is used to view and configure the gratuitous ARP settings. A gratuitous ARP request packet is an ARP request packet where the source and the destination IP address are both set to the IP address of the
  • D-Link DGS-1510 | User Manual - Page 191
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide UDP Helper IP Forward Protocol This window is used to display and configure the IP forward protocol settings. This feature is used to enable the forwarding of a specific UDP service type of packets. To view the following window,
  • D-Link DGS-1510 | User Manual - Page 192
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click L3 Features > UDP Helper > IP Helper Address, as shown below: Figure 6-7 IP Helper Address Window The fields that can be configured are described below: Parameter Interface VLAN IP Helper
  • D-Link DGS-1510 | User Manual - Page 193
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Edit button, the following window will be available. Figure 6-9 IPv4 Interface Configure Window Click the
  • D-Link DGS-1510 | User Manual - Page 194
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Secondary IP Settings are described below: Parameter IP Static/Default Route This window is used to view and configure the IPv4 static and default route settings. The Switch supports static
  • D-Link DGS-1510 | User Manual - Page 195
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click L3 Features > IPv4 Static/Default Route, as shown below: Figure 6-11 IPv4 Static/Default Route Window The fields that can be configured are described below: Parameter IP Address Mask
  • D-Link DGS-1510 | User Manual - Page 196
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter IP Window The fields that can be configured are described below: Parameter Interface VLAN Description Enter the VLAN interface's ID that will be associated
  • D-Link DGS-1510 | User Manual - Page 197
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Detail button, the following page will be available. Figure 6-14 IPv6 Interface (Detail, IPv6 Interface Settings) Window The fields that can be configured the default value on this interface, configure this
  • D-Link DGS-1510 | User Manual - Page 198
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide instruct the connected hosts to use a stateful configuration protocol to obtain auto-configuration messages on the interface here. By default, this feature is enabled on a VLAN interface and disabled on a tunnel interface
  • D-Link DGS-1510 | User Manual - Page 199
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Edit button to configure the following parameters: Figure 6-17 IPv6 Interface (Detail, Neighbor Discover, Edit) Window The fields that can be configured are described below: Parameter Preferred Life Time Valid Life
  • D-Link DGS-1510 | User Manual - Page 200
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IPv6 Neighbor This window is used to configure and view the IPv6 The fields that can be configured are described below: Parameter Interface VLAN IPv6 Address MAC Address Description Enter an interface VLAN ID. Enter the IPv6
  • D-Link DGS-1510 | User Manual - Page 201
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter IPv6 Address/Prefix Length Interface VLAN . Tick the Default Route option to use the default route as the IPv6 address. Enter the interface's VLAN ID that will
  • D-Link DGS-1510 | User Manual - Page 202
    IPMC DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IP Multicast Global Settings This window is used to display and configure the global IP Multicast (IPMC) settings. To view the following window, click L3 Features > IPMC > IP Multicast Global Settings, as shown below:
  • D-Link DGS-1510 | User Manual - Page 203
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 7. Quality of Service (QoS) Basic Settings Advanced Settings Basic Settings Port Default CoS This window is used to view and configure the port's default CoS settings. To view the following window, click QoS > Basic Settings >
  • D-Link DGS-1510 | User Manual - Page 204
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Scheduler Method This window is used to view and configure the port scheduler credit counters will be replenished at that time. All packets are serviced until their credit counter is zero or negative and the last packet
  • D-Link DGS-1510 | User Manual - Page 205
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description and the packet in the next lower CoS queue will be serviced. When the weight of a CoS queue reaches zero, the queue will not be serviced The fields that can be configured are described below: Parameter
  • D-Link DGS-1510 | User Manual - Page 206
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. CoS to Queue Mapping This window is used to view and configure the CoS-to-Queue mapping settings. To view the following window, click QoS > Basic Settings > CoS to Queue Mapping
  • D-Link DGS-1510 | User Manual - Page 207
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Rate Limiting This window is used to view and configure the port rate limiting settings. To view the following window, click QoS > Basic Settings > Port Rate Limiting, as shown below: Figure 7-5 Port Rate Limiting Window
  • D-Link DGS-1510 | User Manual - Page 208
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Queue Rate Limiting This window is used to view and configure the queue rate the traffic in this queue will be serviced first if the minimal bandwidth of all queues is satisfied. The configuration of this command can only be
  • D-Link DGS-1510 | User Manual - Page 209
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description guaranteed bandwidth of made. Advanced Settings DSCP Mutation Map This window is used to view and configure the Differentiated Services Code Point (DSCP) mutation map settings. When a packet is received
  • D-Link DGS-1510 | User Manual - Page 210
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Trust State and Mutation Binding This window is used to view and configure port trust state and mutation binding settings. To view the following window, click QoS > Advanced Settings > Port Trust State and Mutation Binding,
  • D-Link DGS-1510 | User Manual - Page 211
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DSCP CoS Mapping This window is used to view and configure the DSCP CoS mapping settings. To view the following window, click QoS > Advanced Settings > DSCP CoS Mapping, as shown below: Figure 7-9 DSCP CoS Mapping Window
  • D-Link DGS-1510 | User Manual - Page 212
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide CoS Color Mapping This window is used to view and configure the CoS color mapping settings. To view the following window, click QoS > Advanced Settings > CoS Color Mapping, as shown below: Figure 7-10 CoS Color Mapping
  • D-Link DGS-1510 | User Manual - Page 213
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DSCP Color Mapping This window is used to view and configure the DSCP color mapping settings. To view the following window, click QoS > Advanced Settings > DSCP Color Mapping, as shown below: Figure 7-11 DSCP Color Mapping
  • D-Link DGS-1510 | User Manual - Page 214
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Class Map This window is used to view and configure the class map settings. To view the following window, click QoS > Advanced Settings > Class Map, as shown below: Figure 7-12 Class Map Window The fields
  • D-Link DGS-1510 | User Manual - Page 215
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide , SSH, Telnet, and TFTP. Select and enter the VLAN list value that will be matched with the class map is used to view and configure the aggregate policer settings. default action is to Transmit. Options to choose from are: 204
  • D-Link DGS-1510 | User Manual - Page 216
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Exceed Action Violate Action Color Aware Description • Drop - Specifies that the packet will be dropped. • Set-DSCP-Transmit - Enter the IP DSCP value in the space provided. This value sets the IP the default action
  • D-Link DGS-1510 | User Manual - Page 217
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Two Rate Setting tab, at the top of the page, the following page will be available. Figure 7-15 Two Rate Settings Window The fields that can be configured , the default action is Enter the IP DSCP and
  • D-Link DGS-1510 | User Manual - Page 218
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide the violation action is not specified, the default action is equal to the exceed action. • Set-DSCP-1P - Enter the IP DSCP and 1P transmit values in the This window is used to view and configure the policy map settings. To view
  • D-Link DGS-1510 | User Manual - Page 219
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Traffic Policy are described below: Parameter Policy Map Name Class Map Name Description Enter the policy map's name here. This name can be up
  • D-Link DGS-1510 | User Manual - Page 220
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter appear. Figure 7-19 Police Action Window The fields that can be configured are described below: Parameter None Specify Average Rate Normal Burst Size Maximum
  • D-Link DGS-1510 | User Manual - Page 221
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Exceed Action Violate Action Color Advanced Settings > Policy Binding, as shown below: Figure 7-20 Policy Binding Window The fields that can be configured are described below: Parameter Unit From Port / To Port
  • D-Link DGS-1510 | User Manual - Page 222
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 8. Access Control List (ACL) ACL Configuration Wizard ACL Access List ACL Interface Access Group ACL VLAN Access Map ACL VLAN Filter ACL Configuration Wizard This window is used to guide the user to create a new ACL access list
  • D-Link DGS-1510 | User Manual - Page 223
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Next button, the following window will appear. Figure 8-3 ACL Configuration Wizard (Select Packet Type) Window The fields that can be configured are described below: Parameter MAC IPv4 IPv6 Description
  • D-Link DGS-1510 | User Manual - Page 224
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Sequence No. Source Destination Specify Ethernet Type Ethernet Type Ethernet Type Mask CoS VID VLAN , mop-dump, vines-echo, vines-ip, xns-idp, and arp. Enter
  • D-Link DGS-1510 | User Manual - Page 225
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the IPv4 radio button and the Next button, the following window will appear. Figure 8-5 ACL Configuration Wizard (Add UDP, ICMP, EIGRP, ESP, GRE, IGMP, OSPF, PIM, VRRP, IP-in-IP, PCP, Protocol ID, and None. 214
  • D-Link DGS-1510 | User Manual - Page 226
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the TCP option as the Protocol Type, the following section will appear. Figure 8-6 ACL Configuration Wizard (Add Rule for IPv4 ACL) TCP Window The dynamic fields that can be configured are described below:
  • D-Link DGS-1510 | User Manual - Page 227
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination Port IP , the port number(s) can manually be entered in the space(s) provided, if the and 7 (network). After selecting the IP precedence value, select the Type-of-Service (ToS) value that will be used
  • D-Link DGS-1510 | User Manual - Page 228
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the UDP option as the Protocol Type, the following section will appear. Figure 8-7 ACL Configuration Wizard (Add Rule for IPv4 ACL) UDP Window The dynamic fields that can be configured are described below:
  • D-Link DGS-1510 | User Manual - Page 229
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination Port IP Precedence ToS DSCP Time Range Action Description • Range - The start port number and end port number selected, of the range, will be used. Alternatively, the port number(s) can manually be
  • D-Link DGS-1510 | User Manual - Page 230
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ICMP option as the Protocol Type, the following section will appear. Figure 8-8 ACL Configuration Wizard (Add Rule for IPv4 ACL) ICMP Window The dynamic fields that can be configured are described below:
  • D-Link DGS-1510 | User Manual - Page 231
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Message Code IP After selecting the IP precedence value, select the Type-of-Service (ToS) value IP-in-IP, PCP, or Protocol ID option as the Protocol Type, the following section will appear. Figure 8-9 ACL Configuration
  • D-Link DGS-1510 | User Manual - Page 232
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination IP (network). After selecting the IP precedence value, select the Type-of-Service (ToS) value that will be Configuration Wizard (Add Rule for IPv4 ACL) None Window The dynamic fields that can be configured
  • D-Link DGS-1510 | User Manual - Page 233
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Source Destination IP and 7 (network). After selecting the IP precedence value, select the Type-of-Service (ToS) value that will be used window will appear. Figure 8-11 ACL Configuration Wizard (Add Rule for IPv6 ACL)
  • D-Link DGS-1510 | User Manual - Page 234
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fixed fields that can be configured are described below: Parameter Sequence No. Protocol Type Description Enter the ACL rule number here. This value must be between 1 and 65535. Select Auto Assign
  • D-Link DGS-1510 | User Manual - Page 235
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Source Port Destination Port end port number selected, of the range, will be used. Alternatively, the port number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in the
  • D-Link DGS-1510 | User Manual - Page 236
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the UDP option as the Protocol Type, the following section will appear. Figure 8-13 ACL Configuration Wizard (Add Rule for IPv6 ACL) UDP Window The dynamic fields that can be configured are described below:
  • D-Link DGS-1510 | User Manual - Page 237
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide selected, of the range, will be used. Alternatively, the port number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available Configuration Wizard (Add Rule for IPv6 ACL) ICMP Window 226
  • D-Link DGS-1510 | User Manual - Page 238
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The dynamic fields that can be configured are described below: Parameter Source Destination Specify ICMP Message Type ICMP Message Type Message Code DSCP Flow Label Time Range Action Description Select and enter
  • D-Link DGS-1510 | User Manual - Page 239
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the Protocol ID, ESP, PCP, or SCTP option as the Protocol Type, the following section will appear. Figure 8-15 ACL Configuration Wizard (Add Rule for IPv6 ACL) Protocol ID Window The dynamic fields that can be
  • D-Link DGS-1510 | User Manual - Page 240
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Action Description Select the action that will appear. Figure 8-16 ACL Configuration Wizard (Add Rule for IPv6 ACL) None Window The dynamic fields that can be configured are described below: Parameter Fragments
  • D-Link DGS-1510 | User Manual - Page 241
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Configuration Wizard (Apply Port) Window The fields that can be configured configuration here. Select the appropriate port range used for the configuration used to view and configure the ACL access list configured are described below:
  • D-Link DGS-1510 | User Manual - Page 242
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-19 Standard IP ACL (Add ACL Access List) Window The fields that can be configured are described below: creating a Standard IP ACL profile, the newly created Standard IP ACL profile will be displayed in the ACL
  • D-Link DGS-1510 | User Manual - Page 243
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Edit button to re-configure the specific ACL Add Rule button. Figure 8-21 Standard IP ACL (Selected) Window After selecting the ACL profile and clicking the Add Rule button, users can configure the new ACL rule, in the
  • D-Link DGS-1510 | User Manual - Page 244
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination Time Range Description The bit in the ACL profile table). Figure 8-23 Standard IP ACL (Edit ACL) Window The fields that can be configured are described below: Parameter Start Sequence No. Step Counter
  • D-Link DGS-1510 | User Manual - Page 245
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the list of rules, that a new ACL profile, as shown below: Figure 8-25 Extended IP ACL (Add Profile) Window The fields that can be configured are described below: Parameter ACL Type ID ACL Name Description Select
  • D-Link DGS-1510 | User Manual - Page 246
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After creating an Extend IP ACL profile, the newly created Extend IP ACL profile will be displayed in the ACL profile display table, as shown below: Figure 8-26 Extended IP ACL (Main) Window Click the Edit button to re-configure
  • D-Link DGS-1510 | User Manual - Page 247
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ACL profile and clicking the Add Rule button, users can configure the new ACL rule, in the selected ACL profile, as shown below: Figure 8-28 Extended IP ACL (Add Rule) Window This is a dynamic page. Every
  • D-Link DGS-1510 | User Manual - Page 248
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the TCP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-29 Extended IP ACL (Add Rule) TCP Window The dynamic fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 249
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination Port TCP Flag IP Precedence ToS DSCP Time Range Description number(s) can manually ), and 7 (network). After selecting the IP precedence value, select the Type-of-Service (ToS) value that will be used here
  • D-Link DGS-1510 | User Manual - Page 250
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The dynamic fields that can be configured are described below: Parameter Source Destination Source Port Destination Port IP port number(s) can manually be entered in the the IP precedence value, select the Type-of-Service (ToS
  • D-Link DGS-1510 | User Manual - Page 251
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ICMP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-31 Extended IP ACL (Add Rule) ICMP Window The dynamic fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 252
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter IP Precedence ToS DSCP Time Range Description When the ICMP message type is not selected in the Specify ICMP Message Type drop-down list, enter the Message Code numerical value used here. Select the IP precedence
  • D-Link DGS-1510 | User Manual - Page 253
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter IP Precedence ToS DSCP Time Range Description • Host - Enter the destination host's IP address here. • IP - The Wildcard option will also be available. Enter the group of destination IP addresses by using a wildcard
  • D-Link DGS-1510 | User Manual - Page 254
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (Add Profile) Window The fields that can be configured are described below: Parameter ACL Type ID ACL Name Description type here. Options to choose from are Standard IP ACL, Extended IP ACL, Standard IPv6 ACL, Extended IPv6 ACL,
  • D-Link DGS-1510 | User Manual - Page 255
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After creating a Standard IPv6 ACL profile, the newly created Standard IPv6 ACL profile will be displayed in the ACL profile display table, as shown below:
  • D-Link DGS-1510 | User Manual - Page 256
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ACL profile and clicking the Add Rule button, users can configure the new ACL rule, in the selected ACL profile, as shown below: Figure 8-38 Standard IPv6 ACL (Add Rule) Window The fields that can be
  • D-Link DGS-1510 | User Manual - Page 257
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To enable the Counter State option or to enter a Remark for the profile, click the Edit button, next to the specific ACL profile (found in
  • D-Link DGS-1510 | User Manual - Page 258
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Extended IPv6 ACL After clicking the Add ACL button, users can create a new ACL profile, as shown below: Figure 8-41 Extended IPv6 ACL (Add Profile) Window The fields that can be configured are described below: Parameter ACL
  • D-Link DGS-1510 | User Manual - Page 259
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To add an ACL rule in the Type option will change the bottom part of this window. The fixed fields that can be configured are described below: Parameter Sequence No. Description Enter the ACL rule number here. This value
  • D-Link DGS-1510 | User Manual - Page 260
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Action Protocol Type Description Extended IPv6 ACL (Add Rule) TCP Window The dynamic fields that can be configured are described below: Parameter Source Destination Source Port Description Select and enter the
  • D-Link DGS-1510 | User Manual - Page 261
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination Port TCP Flag DSCP Flow port number selected, of the range, will be used. Alternatively, the port number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in
  • D-Link DGS-1510 | User Manual - Page 262
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The dynamic fields that can be configured are port number selected, of the range, will be used. Alternatively, the port number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in
  • D-Link DGS-1510 | User Manual - Page 263
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ICMP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-47 Extended IPv6 ACL (Add Rule) ICMP Window The dynamic fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 264
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter DSCP Flow Label Time Range IPv6 ACL (Add Rule) Protocol ID Window The dynamic fields that can be configured are described below: Parameter Protocol Fragments Source Destination DSCP Description Enter the Protocol ID
  • D-Link DGS-1510 | User Manual - Page 265
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Flow Label Time Range Description Enter 49 Extended IPv6 ACL (Counter State Enabled) Window The fields that can be configured are described below: Parameter Start Sequence No. Stop Counter State Remark Description
  • D-Link DGS-1510 | User Manual - Page 266
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (Add Profile) Window The fields that can be configured are described below: Parameter ACL Type ID ACL Name Description type here. Options to choose from are Standard IP ACL, Extended IP ACL, Standard IPv6 ACL, Extended IPv6 ACL,
  • D-Link DGS-1510 | User Manual - Page 267
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After creating an Extend MAC ACL profile, the newly created Extend MAC ACL profile will be displayed in the ACL profile display table, as shown below: Figure 8-52 Extended MAC ACL (Main) Window Click the Edit button to re-
  • D-Link DGS-1510 | User Manual - Page 268
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ACL profile and clicking the Add Rule button, users can configure etype-8042, lat, lavcsca, mop-console, mop-dump, vines-echo, vines-ip, xns-idp, and arp. Enter the Ethernet type hexadecimal value here. This
  • D-Link DGS-1510 | User Manual - Page 269
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Ethernet Type Mask CoS VID VLAN Range Time Range 8-55 Extended MAC ACL (Edit ACL) Window The fields that can be configured are described below: Parameter Start Sequence No. Stop Counter State Remark Description
  • D-Link DGS-1510 | User Manual - Page 270
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (Add Profile) Window The fields that can be configured are described below: Parameter ACL Type ID ACL Name Description type here. Options to choose from are Standard IP ACL, Extended IP ACL, Standard IPv6 ACL, Extended IPv6 ACL,
  • D-Link DGS-1510 | User Manual - Page 271
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After creating an Expert ACL profile, the newly created Expert ACL profile will be displayed in the ACL profile display table, as shown below: Figure 8-58 Extended Expert ACL (Main) Window Click the Edit button to re-configure
  • D-Link DGS-1510 | User Manual - Page 272
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ACL profile and clicking the Add Rule button, users can configure the new ACL rule, in the selected ACL profile, as UDP, ICMP, EIGRP, ESP, GRE, IGMP, OSPF, PIM, VRRP, IP-in-IP, PCP, Protocol ID, and None. 261
  • D-Link DGS-1510 | User Manual - Page 273
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the TCP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-61 Extended Expert ACL (Add Rule) TCP Window The dynamic fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 274
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination MAC Address Source Port Destination Port IP Precedence ToS DSCP TCP Flag VID VLAN can manually be VLAN range here. Enter the minimum and maximum VLAN ID in the range here. Select the Class of Service
  • D-Link DGS-1510 | User Manual - Page 275
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the UDP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-62 Extended Expert ACL (Add Rule) UDP Window The dynamic fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 276
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination MAC Address Source Port Destination Port IP Precedence ToS DSCP VID VLAN (s) can manually be entered VLAN range here. Enter the minimum and maximum VLAN ID in the range here. Select the Class of Service
  • D-Link DGS-1510 | User Manual - Page 277
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ICMP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-63 Extended Expert ACL (Add Rule) ICMP Window The dynamic fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 278
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination MAC Address Specify ICMP Message Type ICMP Message Type Message Code IP Precedence ToS DSCP VID VLAN VLAN range here. Enter the minimum and maximum VLAN ID in the range here. Select the Class of Service
  • D-Link DGS-1510 | User Manual - Page 279
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the EIGRP, ESP, GRE, IGMP, OSPF, PIM, VRRP, IP-in-IP, PCP, Protocol fields that can be configured are described below: Parameter Fragments Source IP Address Destination IP Address Source MAC Address
  • D-Link DGS-1510 | User Manual - Page 280
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination MAC Address IP Precedence ToS DSCP VID VLAN the VLAN range here. Enter the minimum and maximum VLAN ID in the range here. Select the Class of Service ( configured are described below: Parameter Start Sequence No
  • D-Link DGS-1510 | User Manual - Page 281
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Stop Counter State Remark Description Enter the stop sequence number here. Select to enable or disable the counter state option here. Enter an optional
  • D-Link DGS-1510 | User Manual - Page 282
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ACL Interface Access Group This window is used to view and configure the ACL interface access group settings. To view the following window, click ACL > ACL Interface Access Group, as shown below: Figure 8-67 ACL Interface
  • D-Link DGS-1510 | User Manual - Page 283
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ACL VLAN Access Map This window is used to view and configure the ACL VLAN access map settings. To view the following window, click ACL > ACL VLAN Access Map, as shown below: Figure 8-68 ACL VLAN Access Map Window The fields
  • D-Link DGS-1510 | User Manual - Page 284
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Binding button, the following page will appear. Figure 8-69 Match Access-List Window The fields that can be configured are described below: Parameter Match IP Access-List Match IPv6 Access-List Match MAC
  • D-Link DGS-1510 | User Manual - Page 285
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Action VID List Description Select the action that will be taken here. Options to choose from are Add and Delete. Enter the VLAN ID list that will be used here. Select the All VLANs option to apply this configuration
  • D-Link DGS-1510 | User Manual - Page 286
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 9. Security Port Security 802.1X AAA below: Figure 9-1 Port Security Global Settings Window The fields that can be configured for Port Security Trap Settings are described below: Parameter Trap State Description Click to
  • D-Link DGS-1510 | User Manual - Page 287
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Port Security Trap Rate Settings are described below: Parameter Trap Rate Description Enter the number of traps per second. The range is from 0 to 1000. The default value 0 indicates an
  • D-Link DGS-1510 | User Manual - Page 288
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide not be purged out unless the user manually deletes those entries. • Delete-on- secure address list. This is the default type. • Inactivity - Specifies that used to view, clear, and configure the port security address entries.
  • D-Link DGS-1510 | User Manual - Page 289
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter VID Description Enter the VLAN ID here. This value must be between 1 and 4094. Click the Add button to add a new entry based on the information entered. Click the Delete
  • D-Link DGS-1510 | User Manual - Page 290
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide be running a RADIUS Server program and must be configured properly on the Authenticator (Switch). Clients connected to by the Authentication Server (RADIUS) before attaining any services offered by the Switch on the LAN. The role
  • D-Link DGS-1510 | User Manual - Page 291
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide • The 802.1X settings must be implemented by port (Security > 802.1X > 802.1X Port Settings) • A RADIUS server must be configured on the Switch. (Security > RADIUS > RADIUS Server Settings) Client The Client is simply the end
  • D-Link DGS-1510 | User Manual - Page 292
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The D-Link implementation of 802.1X allows network in this situation is open to attack. Figure 9-10 Example of Typical Port-based Configuration Host-based Network Access Control In order to successfully make use of 802.1X in
  • D-Link DGS-1510 | User Manual - Page 293
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide individual MAC addresses, and effectively creates a logical Port that the attached device can then use to communicate with the LAN via the Switch. Figure 9-11 Example of Typical Host-based Configuration 802.1X Global Settings
  • D-Link DGS-1510 | User Manual - Page 294
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 802.1X Port Settings This window is used to view and configure the 802.1X port settings. To view the be between 1 and 10. By default, this option is 2. This option configures the maximum number of times that the backend 283
  • D-Link DGS-1510 | User Manual - Page 295
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter PAE Authenticator Server Timeout Supp By default, this value is 30 seconds. Click the Apply button to accept the changes made. Authentication Session Information This window is used to view and configure the
  • D-Link DGS-1510 | User Manual - Page 296
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Authenticator Statistics This window is used to below: Figure 9-16 Authenticator Session Statistics Window The fields that can be configured are described below: Parameter Unit Port Description Select the switch unit that
  • D-Link DGS-1510 | User Manual - Page 297
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Authenticator Diagnostics This window is used to view shown below: Figure 9-18 AAA Global Settings Window The fields that can be configured are described below: Parameter AAA State Description Select to enable or disable the
  • D-Link DGS-1510 | User Manual - Page 298
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Application Authentication Settings This window is used to view and configure Settings, as shown below: Figure 9-20 Application Accounting Settings Window The fields that can be configured are described below: Parameter Exec
  • D-Link DGS-1510 | User Manual - Page 299
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Level Commands Method List Description Select the privilege level used here. Options to choose from are levels 1 to 15. Enter the commands method list name used here. Click the Edit button to re-configure the
  • D-Link DGS-1510 | User Manual - Page 300
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured for AAA Authentication MAC-Auth are described below: Parameter Status Method 1 to 4 Description Select to enable or disable the AAA MAC
  • D-Link DGS-1510 | User Manual - Page 301
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Method 1 to 4 Description Select the method lists that will be used for this configuration here. Options to choose from are none, enable, group, radius, and tacacs+. Click the Apply button to accept the changes made
  • D-Link DGS-1510 | User Manual - Page 302
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the AAA Accounting Exec tab, the following page will appear. Figure 9-25 AAA Accounting Exec Window The fields that can be configured are described below: Parameter List Name Method 1 to 4 Description Enter
  • D-Link DGS-1510 | User Manual - Page 303
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Server RADIUS Dynamic Author Settings This window is used to view and configure The fields that can be configured for Server RADIUS Dynamic Author Settings are described below: Parameter Client IP Address Client Host Name Server
  • D-Link DGS-1510 | User Manual - Page 304
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide RADIUS RADIUS Global Settings This window is used to view and configure the RADIUS global settings. To view the following window, click Security > RADIUS > RADIUS Global Settings, as shown below: Figure 9-28 . By default, this
  • D-Link DGS-1510 | User Manual - Page 305
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter IPv6 RADIUS Source Interface Type Interface ID Description Select the IPv6 RADIUS source interface type here. Options to choose from are: • VLAN - Specifies the IPv6 RADIUS source interface type as VLAN 20. By default
  • D-Link DGS-1510 | User Manual - Page 306
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Key Type Key Description Select new entry based on the information entered. Click the Show Detail button to view and configure detailed settings for the RADIUS group server. Click the Delete button to remove the
  • D-Link DGS-1510 | User Manual - Page 307
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described . Options to choose from are: • VLAN - Specifies the IPv4 RADIUS source interface type as VLAN. Interface ID - Enter the VLAN interface ID for the IPv4 RADIUS source interface
  • D-Link DGS-1510 | User Manual - Page 308
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: here. Options to choose from are: • VLAN - Specifies the IPv6 TACACS+ source interface type as VLAN. Enter the VLAN interface ID here. The range is from 1 to 4094
  • D-Link DGS-1510 | User Manual - Page 309
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. TACACS+ Server Settings This window is used to view and configure the TACACS+ server settings. To view the following window, click Security > TACACS+ > TACACS+ Server Settings,
  • D-Link DGS-1510 | User Manual - Page 310
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide TACACS+ Group Server Settings This window is used to view and configure the TACACS+ group server settings. To view the following window, click Security > TACACS+ > TACACS+ Group Server Settings, as shown below: Figure 9-35
  • D-Link DGS-1510 | User Manual - Page 311
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter IPv6 TACACS+ Source Interface State IPv6 TACACS+ Source Interface Type Description • VLAN - Specifies the IPv4 TACACS+ source interface type as VLAN. Interface ID - Enter the VLAN interface ID for the IPv4 TACACS+
  • D-Link DGS-1510 | User Manual - Page 312
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Settings Window The fields that can be configured are described below: Parameter DHCP Snooping Information enabled, the dynamic DHCP snooping binding entry with the same VLAN ID and MAC address on the specific port can move to
  • D-Link DGS-1510 | User Manual - Page 313
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Snooping Port Settings This window is used to view and configure the DHCP snooping port settings. To view the following window, click Security > IMPB > IPv4 > DHCPv4 Snooping > DHCP Snooping Port Settings, as shown below:
  • D-Link DGS-1510 | User Manual - Page 314
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Snooping VLAN Settings This window is used to view and configure the DHCP snooping VLAN settings. To view the following window, click Security > IMPB > IPv4 > DHCPv4 Snooping > DHCP Snooping VLAN Settings, as shown below:
  • D-Link DGS-1510 | User Manual - Page 315
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Store DHCP Snooping Database are described below: Parameter URL Description Select the location from the drop-down list and enter the URL where the
  • D-Link DGS-1510 | User Manual - Page 316
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the 44 ARP Access List - Edit Window The fields that can be configured are described below: Parameter Action IP Sender IP Description Select the action that will be taken here. Options to
  • D-Link DGS-1510 | User Manual - Page 317
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Sender IP Mask MAC Sender MAC Sender MAC Mask Description After selecting the IP with Mask option as the type of IP, enter the sender IP This window is used to view and configure the ARP inspection settings. To view
  • D-Link DGS-1510 | User Manual - Page 318
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description also specifies to check the validity of IP address in the ARP payload. The sender IP in both the ARP request and response and target IP in the ARP response are validated. Packets destined for the IP
  • D-Link DGS-1510 | User Manual - Page 319
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ARP Inspection Port Settings This window is used to view and configure the ARP inspection port settings. To view the following window, to accept the changes made. Click the Set to Default button to change the information to the
  • D-Link DGS-1510 | User Manual - Page 320
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ARP Inspection VLAN This window is used to view and configure the ARP inspection VLAN settings. To view the following window, click Security > IMPB > IPv4 > Dynamic ARP Inspection > ARP Inspection VLAN, as shown below: Figure
  • D-Link DGS-1510 | User Manual - Page 321
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ARP Inspection Log This window is used to view, configure, and clear the ARP inspection log information. To view the following window, click Security > IMPB > IPv4 > Dynamic ARP Inspection > ARP Inspection Log, as shown below:
  • D-Link DGS-1510 | User Manual - Page 322
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IP Source Guard Binding This window is used to view and configure the IP source guard binding settings. To view the following window, click Security > IMPB > IPv4 > IP Source Guard > IP Source Guard Binding, as shown below:
  • D-Link DGS-1510 | User Manual - Page 323
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description • Static - Specifies to display the IP-source guard binding entry that is manually configured. Click the Find button to locate a specific entry based on the information entered. Click the Delete button
  • D-Link DGS-1510 | User Manual - Page 324
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Advanced Settings IP-MAC-Port Binding Settings This window is used to view and configure the IP-MAC-Port binding settings. To view the following window, click Security > IMPB > IPv4 > Advanced Settings > IP-MAC-Port Binding
  • D-Link DGS-1510 | User Manual - Page 325
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description MAC address, VLAN ID, and arrival port number must match any of the entries defined by either the IP source guard static binding entry or the DHCP snooping learned dynamic binding entry. When a port is
  • D-Link DGS-1510 | User Manual - Page 326
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IPv6 IPv6 Snooping This window is used to view and configure the IPv6 snooping settings. To is designed for a stateless auto-configuration assigned IPv6 address and manually configured IPv6 address. Before assigning an IPv6
  • D-Link DGS-1510 | User Manual - Page 327
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IPv6 ND Inspection This window is used to view and configure the IPv6 ND inspection settings. To view the following window, click Security > IMPB > IPv6 > IPv6 ND Inspection, as shown below: Figure 9-56 IPv6 ND Inspection
  • D-Link DGS-1510 | User Manual - Page 328
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IPv6 RA Guard This window is used to view and configure the IPv6 Router Advertisement (RA) guard settings. To view the following window, click Security > IMPB > IPv6 > IPv6 RA Guard, as shown below: Figure 9-57 IPv6
  • D-Link DGS-1510 | User Manual - Page 329
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below Settings Window The fields that can be configured are described below: Parameter Policy Name Global Auto-Configure Address Link Local Traffic Target Port Unit Description
  • D-Link DGS-1510 | User Manual - Page 330
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter From Port / To Port Description Select the appropriate port range used for the configuration here. Click the Apply button to accept the changes made. Click the Edit button to re-configure Enter the VLAN ID used here
  • D-Link DGS-1510 | User Manual - Page 331
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide both provide DHCP services to different IP address is the same as the DHCP server's IP address (UDP port number 67). These rules are used to permit the DHCP server packets with specific fields, which the user has configured
  • D-Link DGS-1510 | User Manual - Page 332
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Delete button to remove the specified entry. Click the Delete Profile button to remove the specified profile. The fields that can be configured for Log Information
  • D-Link DGS-1510 | User Manual - Page 333
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter State Server IP Profile Name Description Select to enable or disable the DHCP server screening function on the port(s) specified. Enter the DHCP server's IP address here. Enter the DHCP server screening profile that
  • D-Link DGS-1510 | User Manual - Page 334
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Delete button to remove the specified entry. BPDU Attack Protection This window is used to view and configure the BPDU attack protection settings. In generally, there
  • D-Link DGS-1510 | User Manual - Page 335
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description • Drop - Drop all accept the changes made. MAC Authentication This window is used to view and configure the MAC authentication settings. MAC authentication is a feature designed to authenticate a
  • D-Link DGS-1510 | User Manual - Page 336
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for MAC Authentication authentication process of WAC by attempting to gain Web access. D-Link's implementation of WAC uses a virtual IP that is exclusively used by the WAC function and is not
  • D-Link DGS-1510 | User Manual - Page 337
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide authentication processing, or to access the login page. If not specified, the default port number for HTTP is 80 and the default port number for HTTPS is 443. If no protocol is specified, the default protocol is HTTP. The
  • D-Link DGS-1510 | User Manual - Page 338
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Conditions and Limitations • If the client is utilizing DHCP to attain an IP address, the authenticating VLAN must provide a DHCP server or a DHCP relay functions so that client may obtain an IP address. • Certain functions
  • D-Link DGS-1510 | User Manual - Page 339
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide WAC Port Settings This window is used to view and configure the WAC port settings. To view the following window, click Security > Web-based Access Control > WAC Port Settings, as shown below: Figure 9-68 WAC Port
  • D-Link DGS-1510 | User Manual - Page 340
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide WAC Customize Page This window is used to view and configure the WAC customized login information. Click the Set to Default button to replace the information with the default information. Click the Apply button to accept the
  • D-Link DGS-1510 | User Manual - Page 341
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Japanese Web-based Access Control JWAC Global Settings This window is used to view and configure the virtual IP option used here. Options to choose from are IPv4, IPv6, and URL. After selecting IPv4 as the Virtual IP, the
  • D-Link DGS-1510 | User Manual - Page 342
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter IPv6 Address Virtual URL Forcible Logout Redirect State Redirect Destination Redirect Delay Time Description server to get the virtual IP address. The obtained IP address must match the virtual IP address configured
  • D-Link DGS-1510 | User Manual - Page 343
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Update Server Settings are described below: Parameter IPv4 Network Prefix/Prefix Length IPv6 Network Prefix/Prefix Length Port Description Enter the update server's IPv4
  • D-Link DGS-1510 | User Manual - Page 344
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit From Port / To Port State Max Authenticating User Description Select the switch unit that will be used for this configuration here. Select the appropriate
  • D-Link DGS-1510 | User Manual - Page 345
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide JWAC Customize Page This window is used to view and configure the JWAC customize information. Click the Set to Default button to replace the information with the default information. Click the Apply button to accept the
  • D-Link DGS-1510 | User Manual - Page 346
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After changing the language to Japanese the JWAC customize page will look like this. Figure 9-74 JWAC Customize Page (Japanese) Window Click the Set to Default button to replace the information with the default information.
  • D-Link DGS-1510 | User Manual - Page 347
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Delete button to remove the specified entry. Network Access Authentication Global Settings This window is used to view and configure and 1000. By default, this option
  • D-Link DGS-1510 | User Manual - Page 348
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Authorization State Description If the acceptance of an authorized configuration. When authorization is enabled for authentication, the authorized attributes (for example VLAN, 802.1p default priority, bandwidth, and
  • D-Link DGS-1510 | User Manual - Page 349
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Network Access Authentication Port Settings This window is used to view and configure following parameter is available. Enter the VLAN ID used here. This is useful when different VLANs on the Switch have different authentication
  • D-Link DGS-1510 | User Manual - Page 350
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide here. This value must be between 1 and 65535 seconds. By default, this value is 3600 seconds. Select to enable or disable the Information Window The fields that can be configured are described below: Parameter Port MAC Address
  • D-Link DGS-1510 | User Manual - Page 351
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide capability. To alleviate this problem, the Safeguard Engine function available for ARP and broadcast IP packets. If the CPU load table a list of supported protocols are displayed Configuration Protocol Domain Name System GARP VLAN
  • D-Link DGS-1510 | User Manual - Page 352
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide the Switch will allot bandwidth to various traffic flows (ARP, IP) using the FFP (Fast Filter Processor) metering table to control value must be between 20% and 100%. This value is used to configure the acceptable level of CPU
  • D-Link DGS-1510 | User Manual - Page 353
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Falling Threshold Description the Switch will move into Exhausted mode, based on the parameters provided in this window. Enter the falling threshold value here. This value must be between 20 view and configure the CPU
  • D-Link DGS-1510 | User Manual - Page 354
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for CPU Protect the Apply button to accept the changes made. The fields that can be configured for Sub-Interface Information are described below: Parameter Sub-Interface Description Select
  • D-Link DGS-1510 | User Manual - Page 355
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Other, IGMP, LACP, SNMP, Host, as shown below: Figure 9-83 Trusted Host Window The fields that can be configured are described below: Parameter ACL Name Type Description Enter the ACL name used here.
  • D-Link DGS-1510 | User Manual - Page 356
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click Security > Traffic Segmentation Settings, as shown below: Figure 9-84 Traffic Segmentation Settings Window The fields that can be configured are described below: Parameter Unit From Port /
  • D-Link DGS-1510 | User Manual - Page 357
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Storm Control Settings This window is used to view and configure the storm control settings. To here. This value must be between 5 and 600 seconds. By default, this value is 5 seconds. Enter the retries value used here. This value
  • D-Link DGS-1510 | User Manual - Page 358
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Storm Control Port 0 and 2147483647 packets per second. If the low PPS value is not specified, the default value is 80% of the specified risen PPS. Enter the low packets per second value
  • D-Link DGS-1510 | User Manual - Page 359
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the Level option as the Level Type, the following parameters are available. Figure 9-87 Storm Control (Level) Window The fields that can be configured are described below: Parameter Level Rise Level Low
  • D-Link DGS-1510 | User Manual - Page 360
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click Security > DoS Attack Prevention Settings, as shown below: Figure 9-88 DoS Attack Prevention Settings Window The fields that can be configured and secure network services over an insecure
  • D-Link DGS-1510 | User Manual - Page 361
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide • Configure the User Account to use a specified authorization method to identify users that are allowed to establish SSH connections with the Switch using the SSH User
  • D-Link DGS-1510 | User Manual - Page 362
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Host Key This window is used to view and generate the SSH host key. To view the following window, click Security > SSH > Host Key, as shown below: Figure 9-90 Host Key Window The fields that can be configured for Host Key
  • D-Link DGS-1510 | User Manual - Page 363
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide SSH User Settings This window is used to view and configure the SSH user settings. To view the following window, click the messages sent between client and host. The Switch supports two types of cryptology algorithms: 352
  • D-Link DGS-1510 | User Manual - Page 364
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide supports TLS 1.0, TLS 1.1, and TLS 1.2. Other versions of SSL may not be compatible with this Switch and may cause problems Global Settings This window is used to view and configure the SSL feature's global settings. To view the
  • D-Link DGS-1510 | User Manual - Page 365
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Service Policy Description Enter the service policy name here. This name can be up to 32 characters long. Click the Apply button to accept the changes made. The fields that can be configured for Import File are
  • D-Link DGS-1510 | User Manual - Page 366
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter TFTP Server configure the SSL service policy settings. To view the following window, click Security > SSL > SSL Service Policy, as shown below: Figure 9-95 SSL Service Policy Window The fields that can be configured
  • D-Link DGS-1510 | User Manual - Page 367
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Secure Trustpoint Cipher Suites Description a specific entry based on the information entered. Click the Edit button to re-configure the specific entry. Click the Delete button to remove the specified entry. Network
  • D-Link DGS-1510 | User Manual - Page 368
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 10. OAM Cable Diagnostics DDM Cable Diagnostics The cable diagnostics feature is designed primarily for administrators or customer service this configuration here. Select the appropriate port range used for the configuration here
  • D-Link DGS-1510 | User Manual - Page 369
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide threshold settings, voltage threshold settings, bias current threshold settings, Tx power threshold settings, and Rx power threshold settings. DDM Settings The window is used to configure the action that will occur for specific
  • D-Link DGS-1510 | User Manual - Page 370
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DDM Temperature Threshold Settings This window is used to configure the DDM Temperature Threshold Settings for specific ports on the Switch. To view the following window, click OAM > DDM > DDM Temperature Threshold Settings, as
  • D-Link DGS-1510 | User Manual - Page 371
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit Port Action Type Value Description Select the switch unit that will be used for this configuration here. Select the port used for the configuration here.
  • D-Link DGS-1510 | User Manual - Page 372
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DDM TX Power Threshold Settings This window is used to configure the the changes made. DDM RX Power Threshold Settings This window is used to configure the threshold of RX power for specific ports on the Switch. To view the
  • D-Link DGS-1510 | User Manual - Page 373
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 10-7 DDM RX Power Threshold Settings Window The fields that can be configured are described below: Parameter Unit Port Action Type Power Unit Value Description Select the switch unit that will be used for this
  • D-Link DGS-1510 | User Manual - Page 374
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 11. Monitoring Utilization Statistics Utilization, as shown below: Figure 11-1 Port Utilization Window The fields that can be configured are described below: Parameter Unit From Port / To Port Description Select the switch
  • D-Link DGS-1510 | User Manual - Page 375
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Statistics Port This window is used to display the packet statistics of ports. To view the following window, click Monitoring > Statistics > Port, as shown below: Figure 11-2 Port Window The fields that can be configured are
  • D-Link DGS-1510 | User Manual - Page 376
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Show Detail button, the following page will appear. Figure 11-3 Port Detail Window Click the Back button to return to the previous window. Click the Refresh button to refresh the display table. 365
  • D-Link DGS-1510 | User Manual - Page 377
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Counters This window is used to display port the switch unit that will be used for this configuration here. Select the appropriate port range used for the configuration here. Click the Find button to locate a specific
  • D-Link DGS-1510 | User Manual - Page 378
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Show Errors button, the following page will appear. Figure 11-5 Counters Errors Window Click the Back button to return to the previous
  • D-Link DGS-1510 | User Manual - Page 379
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit From Port / To Port Description Select the switch unit that will be used for this configuration here. Select the appropriate port range used for the
  • D-Link DGS-1510 | User Manual - Page 380
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide monitoring device to the mirroring port, such as a sniffer or an RMON probe, to view details about the packets passing through the first port. This is useful for network monitoring and troubleshooting , to configure the source
  • D-Link DGS-1510 | User Manual - Page 381
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Mirror Session Table are described below: Parameter Mirror Session Type Description Select the mirror session type of information that will be displayed from the
  • D-Link DGS-1510 | User Manual - Page 382
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide sFlow Receiver Settings This window is used to view and configure receivers single sFlow datagram here. The range is from 700 to 1400 bytes. By default, this value is 1400 bytes. Enter the remote sFlow collector's IPv4 or IPv6
  • D-Link DGS-1510 | User Manual - Page 383
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide sFlow Sampler Settings This window is used to view and configure sFlow 0 and 65536. Entering 0 will disable this function. If not specified, the default value is 0. Enter the maximum number of bytes that should be copied from
  • D-Link DGS-1510 | User Manual - Page 384
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide sFlow Poller Settings This window is used to view and configure the sFlow Poller be between 0 and 120 seconds. Entering 0 will disable this feature. By default, this value is 0. Click the Apply button to accept the changes made
  • D-Link DGS-1510 | User Manual - Page 385
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 12. Green Power Saving EEE Power Saving This window is used to configure the This will not affect the port's capabilities when the port status is link up. Length Detection Power Saving Select this option to enable or disable
  • D-Link DGS-1510 | User Manual - Page 386
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Scheduled Dim-LED Power Saving button to remove the specified entry. NOTE: The hibernation feature can only be configured when physical stacking is disabled on this switch. After clicking the Power Saving Shutdown
  • D-Link DGS-1510 | User Manual - Page 387
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Energy Efficient Ethernet (EEE) is defined in IEEE 802.3az. It is designed to reduce the energy consumption of a link used for this configuration here. Select the appropriate port range used for the configuration here. Select
  • D-Link DGS-1510 | User Manual - Page 388
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 13. Toolbar Save Tools Wizard Online Help Surveillance Mode Logout Save Save Configuration This window is used to save the running configuration to the start-up configuration or the file system of the Switch. This is to prevent
  • D-Link DGS-1510 | User Manual - Page 389
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit Source File Destination File Description Select the switch unit that will be used for this configuration here. Enter the source filename and path of the
  • D-Link DGS-1510 | User Manual - Page 390
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click Tools > Firmware Upgrade & Backup > Firmware Backup to HTTP, as shown below: Figure 13-4 Firmware Backup to HTTP Window The fields that can be configured are described below: Parameter Unit
  • D-Link DGS-1510 | User Manual - Page 391
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Configuration Restore & Backup Configuration Restore from HTTP This window is used to initiate a configuration restore from a local PC using HTTP. To view the following window, click Tools > Configuration Restore & Backup >
  • D-Link DGS-1510 | User Manual - Page 392
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit TFTP Server IP Source File Destination File Replace Description Select the switch unit that will be used for this configuration here. Enter the TFTP server
  • D-Link DGS-1510 | User Manual - Page 393
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Configuration Backup to TFTP This window is used to initiate a configuration file backup to a TFTP server. To view the following window, click Tools > Configuration Restore & Backup > Configuration Backup to TFTP, as shown below
  • D-Link DGS-1510 | User Manual - Page 394
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described The fields that can be configured are described below: Parameter TFTP Server IP Destination File Log Type Description Enter the TFTP server's IP address here. When the IPv4
  • D-Link DGS-1510 | User Manual - Page 395
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Ping Ping is a small program that sends address will be used as the packets' source IP address sent to the remote host, or as primary IP address. The fields that can be configured for IPv6 Ping are described below: Parameter
  • D-Link DGS-1510 | User Manual - Page 396
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Source IPv6 Address Description Enter entered, this IPv6 address will be used as the packets' source IP address sent to the remote host, or as primary IP address. Click the Start button to initiate the Ping Test for
  • D-Link DGS-1510 | User Manual - Page 397
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trace Route The trace route page allows the here. The range is from 1 to 9. If unspecified, the default value is 1. The fields that can be configured for IPv6 Trace Route are described below: Parameter IPv6 Address Max TTL
  • D-Link DGS-1510 | User Manual - Page 398
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Probe Times Description Enter the probe time number here. The range is from 1 to 9. If unspecified, the default value is 1. Click the Start button to initiate the route trace for each individual section. After
  • D-Link DGS-1510 | User Manual - Page 399
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Language defaults including IP address and stacking information, and the will save, reboot. - To reset the Switch's configuration to its factory default settings. • The Switch will be reset to its factory default except IP
  • D-Link DGS-1510 | User Manual - Page 400
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Reboot System This window is used to reboot the Switch and alternatively save the configuration before doing so. To view the following window, click Tools > Reboot System, as shown below: Figure 13-20 Reboot System Window When
  • D-Link DGS-1510 | User Manual - Page 401
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Surveillance Mode Click the Surveillance 22 Surveillance Mode Confirmation Message The window above displays a message that the abovementioned configurations need to be changed when access to the Surveillance Mode is given. Click
  • D-Link DGS-1510 | User Manual - Page 402
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 14. Surveillance Mode Surveillance Overview Port Information IP the number of devices, device type, IP address, power consumption, link speed, and errors). Click on the 'more' link to get more information about the devices
  • D-Link DGS-1510 | User Manual - Page 403
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter the total amount of ONVIF IP cameras connected to the Ethernet ports on the Switch. This displays the total amount of D-Link legacy IP cameras (detected by ASV
  • D-Link DGS-1510 | User Manual - Page 404
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter PoE Description Select the maximum power that will be supplied on the PoE port. Options to choose from are Auto, 4W, 7W, 15.4W, 30W, and a configurable value
  • D-Link DGS-1510 | User Manual - Page 405
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Cancel button to discard the changes made. After clicking Ping Test button, the following window will appear. Figure 14-5 PD Alive Configuration . If you are having problems with surveillance devices not being
  • D-Link DGS-1510 | User Manual - Page 406
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Device Information After clicking the Device Information tab, the following window will appear. Figure 14-6 Device Information Window The fields that can be configured are described below: Parameter Unit Description Select
  • D-Link DGS-1510 | User Manual - Page 407
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Information This window is used to display port information like throughput, distance of the network cable, PoE provisioning status, power consumption, Loopback Detection status, group, and how many IP cameras, NVRs, and
  • D-Link DGS-1510 | User Manual - Page 408
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description This displays the total Viewer, Video Encoder, Network Storage, and Other IP Surveillance Device. Group Details After clicking Group Details link, the following window will appear. Figure 14-8 Port
  • D-Link DGS-1510 | User Manual - Page 409
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description This displays the model name of the IP camera. This displays the IP Address and MAC Address of the IP camera or NVR. This displays the description of the device connected to the port. Click the < Back
  • D-Link DGS-1510 | User Manual - Page 410
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description The displays the total amount of inbound bandwidth that is being used by the ONVIF IP cameras connected to the Ethernet ports on the Switch. The displays the total power consumption and power class (of
  • D-Link DGS-1510 | User Manual - Page 411
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter the amount of inbound bandwidth that is being used by the NVR. This displays the IP address and MAC address of the NVR. This displays the description for the NVR.
  • D-Link DGS-1510 | User Manual - Page 412
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide PoE Information This window is used to display Power-over-Ethernet (PoE) information. To view the following window, click PoE Information, as shown below: Figure 14-11 PoE Information Window The fields that can be configured
  • D-Link DGS-1510 | User Manual - Page 413
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter link to redirect the Health Diagnostic window for more information. This displays the PoE consumption and power class of the PD connected to the port. PoE Scheduling This window is used to display and configure
  • D-Link DGS-1510 | User Manual - Page 414
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Alternatively, click to a specific page when multiple pages exist. The fields that can be configured in the PoE Configuration section are described below: Parameter Unit From Port / To Port Time Range
  • D-Link DGS-1510 | User Manual - Page 415
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Unit Path Description Select the unit ID of the Switch in the stack that will be used here. Enter the path
  • D-Link DGS-1510 | User Manual - Page 416
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter startup-config running-config Source File Destination File Replace Description Select this option to use the startup configuration of the Switch in the copy. Select this option to use the running configuration of the
  • D-Link DGS-1510 | User Manual - Page 417
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide SNTP Settings This window is used to display and configure the Simple Network Time seconds. By default, this value is 720 seconds. Click the Apply button to accept the changes made. The fields that can be configured in the SNTP
  • D-Link DGS-1510 | User Manual - Page 418
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Surveillance Settings This window is used to display and configure the surveillance settings. The Switch has only one Surveillance VLAN. This surveillance VLAN also supports to recognize the surveillance devices, like IP Cameras
  • D-Link DGS-1510 | User Manual - Page 419
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured entry. The uplink ports join all surveillance VLANs since they forward surveillance traffic to other switches below: Figure 14-20 Surveillance Log Window Click the Refresh button to refresh
  • D-Link DGS-1510 | User Manual - Page 420
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Backup button to upload the surveillance log to the PC using HTTP. Enter a page number and click the Go button to navigate to a
  • D-Link DGS-1510 | User Manual - Page 421
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ONVIF IP cameras and NVRs discovered on the port. Click the hyperlink (1) to view the group details associated with IP camera be used for this configuration here. Enter the source filename and path of the firmware file located on
  • D-Link DGS-1510 | User Manual - Page 422
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Firmware Backup to HTTP This window is used to initiate a firmware backup to a local unit that will be used for this configuration here. Enter the source filename and path of the configuration file located on the local PC. This
  • D-Link DGS-1510 | User Manual - Page 423
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Destination File Replace Description Enter the destination filename and path where the configuration file should be stored on the Switch. This field can be up to 64 characters long. Select the running-config option
  • D-Link DGS-1510 | User Manual - Page 424
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Language File Description Click the Browse button to navigate to the location of the firmware file located on the local PC. Click the Apply button to initiate
  • D-Link DGS-1510 | User Manual - Page 425
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Save Save Configuration This window is used to save the running configuration to the start-up configuration or the file system of the Switch. This is to prevent the loss of configuration in the event of a power failure. To view
  • D-Link DGS-1510 | User Manual - Page 426
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 14-31 Help (Table) Window Online Help D-Link Support Site Click this option to connect to the D-Link support website. An Internet connection is required. User Guide Click this option to connect to the online user guide
  • D-Link DGS-1510 | User Manual - Page 427
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide . (2) no server(s) responding. (3) no servers configured. (4) no resources. (5) user timeout expired. [from ] authenticated by AAA (Username: ) Parameters Description
  • D-Link DGS-1510 | User Manual - Page 428
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Log Message: Login failed through [from ] authenticated by AAA (Username: ) Parameters Description: exec-type: It indicates the EXEC types, e.g.: Console
  • D-Link DGS-1510 | User Manual - Page 429
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description server-ip: It indicates the AAA server IP address. username: It indicates the username for authentication. Severity Event Description: This log will be generated when RADIUS assigned a valid VLAN ID attributes
  • D-Link DGS-1510 | User Manual - Page 430
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ARP Spoofing configuring from DDP(Username: , IP: ) Parameters Description: Unit: Box ID username: Represent current login user. ipaddr: Represent client IP address. Informational Auto Surveillance VLAN
  • D-Link DGS-1510 | User Manual - Page 431
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Severity Event Description: When an IPC is removed from the surveillance VLAN, the log message will be sent. Log Message: ASV: Remove IPC() Parameters Description: ipaddr: Represent the IP address of
  • D-Link DGS-1510 | User Manual - Page 432
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description pathFile: Path and file name on server. Event description: Firmware upgraded unsuccessfully. Log Message: [Unit , ]Firmware upgraded by unsuccessfully (Username: [, IP: , MAC:
  • D-Link DGS-1510 | User Manual - Page 433
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Log Message: [Unit , ]Configuration downloaded by unsuccessfully. (Username: [, IP: , MAC: ], Server IP: , File Name: ) Parameters description:
  • D-Link DGS-1510 | User Manual - Page 434
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Parameters description: unitID: The unit ID. session: The user's session. username: Represent current login user. ipaddr: Represent client IP address. macaddr: Represent client MAC address. Event description:
  • D-Link DGS-1510 | User Manual - Page 435
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Parameters Description: type: The type of ARP packet, it indicates that ARP packet is request or ARP response. Severity DDM Log Description Severity
  • D-Link DGS-1510 | User Manual - Page 436
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Parameters Description: : Name of the DHCPv6 client interface. Severity Event Description: DHCPv6 client obtains an ipv6 address from a DHCPv6 server. Log
  • D-Link DGS-1510 | User Manual - Page 437
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (IP: Port ) Parameters Description: dos-type: DOS attack type ip-address: IP address disabled state. Warning Log Message: Port VLAN enters error disable state due to
  • D-Link DGS-1510 | User Manual - Page 438
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description vid: The VLAN ID. Severity Event Description: When a port leaves the error-disabled state. Log Message: Port VLAN leaves the error disable state which is previously caused by
  • D-Link DGS-1510 | User Manual - Page 439
    LACP LBD DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description vlan-id: The VLAN ID on which the Description: Member port detach from Link Aggregation Group. Informational Log Message: detach from Link Aggregation Group Parameters
  • D-Link DGS-1510 | User Manual - Page 440
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Log Message: VLAN LBD loop recovered Parameters Description: interface-id: Interface on which loop is detected. vlan-id: VLAN on which loop is detected. Event Description: Record the
  • D-Link DGS-1510 | User Manual - Page 441
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description 6. interfaceName(6) 7. local(7) chassisID: chassis ID. portType: port ID subtype. Value list: 1. interfaceAlias(1) 2. portComponent(2) 3. macAddress(3) 4. networkAddress(4) 5. interfaceName(5) 6. agentCircuitId
  • D-Link DGS-1510 | User Manual - Page 442
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Event Description: Login through console unsuccessfully. Username: , IP: ) Parameters Description: username: Represent current login user. ipaddr: Represent client IP address. Event Description:
  • D-Link DGS-1510 | User Manual - Page 443
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Parameters Description: username: Represent current login user. ipaddr: Represent client IP id: The interface on which the host is authenticated. vlan-id: The VLAN ID on which the host exists after it is
  • D-Link DGS-1510 | User Manual - Page 444
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Event Description: The authorized priority>) Parameters Description: Instance-id: MST instance id. Instance 0 represents for default instance, CIST. macaddr: The system of bridge mac address. priority: The
  • D-Link DGS-1510 | User Manual - Page 445
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Event configuration ID VLAN mapping table change (instance: add vlan [- ]) Parameters Description: Instance-id: MST instance id. Instance 0 represents for default
  • D-Link DGS-1510 | User Manual - Page 446
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description endvlanid: The end vid of delete vlan range. Event Description: Used Description: Instance-id: MST instance id. Instance 0 represents for default instance, CIST. Interface_id: The port number which detect the
  • D-Link DGS-1510 | User Manual - Page 447
    PoE DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Event Description: Total : , PD: ) Parameters Description: portNum: The port number. ipaddr: The IP (IPv4/IPv6) address of PD. Event Description: Power removal due to absence of Maintain
  • D-Link DGS-1510 | User Manual - Page 448
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Log Message: ASV: Port < from with invalid community string Parameters Description: ipaddr: The IP address. Severity Informational SSH Log Description Event Description: SSH server is
  • D-Link DGS-1510 | User Manual - Page 449
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Log Message: Unit: , MAC:
  • D-Link DGS-1510 | User Manual - Page 450
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description SIOn: Represents the SIO interface number. Current Supported SIO interface number should be SIO1 and SIO2. Event Description: SIO interface link down. For SIO Trunk, the last member port link down will trigger
  • D-Link DGS-1510 | User Manual - Page 451
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Log Message: [Unit , ]System The IP address of telnet client. username: the user name that used to login telnet server. Severity Informational Warning Informational Informational Voice-VLAN Log
  • D-Link DGS-1510 | User Manual - Page 452
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description Severity Event Description: When an interface leaves the voice VLAN : , IP: ) Parameters Description: username: The use name that used to login SSL server. ipaddr: The IP address of SSL
  • D-Link DGS-1510 | User Manual - Page 453
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Log Description ipaddr: The IP address of SSL client. Event Description: Logout through Web(SSL). Log Message: Logout through Web(SSL) (Username: , IP: ) Parameters Description: username: The use name that
  • D-Link DGS-1510 | User Manual - Page 454
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Appendix B - Trap Entries The following tables list the trap log entries and their corresponding meanings that will appear in the switch. 802.1X Trap Name
  • D-Link DGS-1510 | User Manual - Page 455
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name dDdmWarningTrap Description OID situation to normal status. Only when the current value> low warning or current value
  • D-Link DGS-1510 | User Manual - Page 456
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide General Description The trap is sent when IP address conflicted. Binding objects: , has detected that the ifOperStatus object for one of its communication links left the down state and transitioned into some other state (but
  • D-Link DGS-1510 | User Manual - Page 457
    LBD DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name dLbdLoopOccurred dLbdLoopRestart dLbdVlanLoopOccurred dLbdVlanLoopRestart Description This trap is sent when an interface loop occurs. Binding objects: (1) dLbdNotifyInfoIfIndex This trap is sent when an
  • D-Link DGS-1510 | User Manual - Page 458
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name dMacAuthLoggedFail dMacAuthLoggedAgesOut Description The optional. A topologyChange trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the
  • D-Link DGS-1510 | User Manual - Page 459
    PoE DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name dEntityExtFactoryResetButton Description (1) trap indicates if the PD device has the stop working or no response problem. At least 500 msec must elapse between notifications being emitted by the
  • D-Link DGS-1510 | User Manual - Page 460
    Port DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name linkUp linkDown Description A notification is generated when port its rising threshold and generates an event 0.1 that is configured for sending SNMP traps. Binding objects: (1) alarmIndex (2) alarmVariable
  • D-Link DGS-1510 | User Manual - Page 461
    Stack SIM DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name dSafeguardChgToNormal Description (1) send this notification when 1.3.6.1.4.1.171 its member generates a link down notification. .12.8.6.0.13 Binding objects: (1) swSingleIPMSID
  • D-Link DGS-1510 | User Manual - Page 462
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name swSingleIPMSLinkUp swSingleIPMSAuthFail swSingleIPMSnewRoot swSingleIPMSTopologyChange Description OID The commander switch will send this notification when 1.3.6.1.4.1.171 its member generates a link configuration
  • D-Link DGS-1510 | User Manual - Page 463
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide System File Trap Name dsfUploadImage dsfDownloadImage configuration file successfully. The notification is sent when the user downloads configuration file successfully. The notification is sent when the user saves configuration
  • D-Link DGS-1510 | User Manual - Page 464
    on the DGS-1510 is used in the following modules: Console, Telnet, SSH, Web, 802.1X, MAC-based Access Control, JWAC, and WAC. The description that follows explains the following RADIUS Attributes Assignment types: • Privilege Level • Ingress/Egress Bandwidth • 802.1p Default Priority • VLAN • ACL
  • D-Link DGS-1510 | User Manual - Page 465
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To assign the 802.1p Default Priority by the RADIUS server, the proper parameters should be configured on the RADIUS server. The table below shows the parameters for 802.1p default priority. The parameters of the Vendor-
  • D-Link DGS-1510 | User Manual - Page 466
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Tag field value (0x00, 0x03 ~ 0x1F, >0x1F) String field format VLAN IDs and check if there is one matched. If the switch can find one matched, it will move to that VLAN. If the switch cannot find the matched VLAN ID, it will
  • D-Link DGS-1510 | User Manual - Page 467
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Filter Rule Format Use the permit command to add a permit entry. Use the deny command to add a deny entry. {permit | deny} in tcp from any to {any | DST-IP-ADDR | DST-IP-NET-ADDR | DST-IPV6-ADDR | DST-IPV6-NET-ADDR} [TCP-PORT-
  • D-Link DGS-1510 | User Manual - Page 468
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide RADIUS Tunnel Attribute Description Value Usage Vendor-Type Defines the attribute. 14 (for ACL script) Required Attribute-Specific Field IPv6 filter rule, Used to This
  • D-Link DGS-1510 | User Manual - Page 469
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Appendix D - IETF RADIUS Attributes Support Remote Authentication Dial-In User Service (RADIUS) attributes carry specific authentication, authorization, information and configuration details for the request and reply. This
  • D-Link DGS-1510 | User Manual - Page 470
    DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Number 95 IETF Attribute NAS-IPv6-Address RADIUS Accounting Attributes: Number 1 4 5 6 8 31 32 40 41 42 43 44 45 46 47 48 49 52 53 61 95 IETF Attribute User-Name NAS-IP-Address NAS-Port Service-Type Framed-IP-Address
  • D-Link DGS-1510 | User Manual - Page 471
    1 to 20 V Model Name ERPS DGS-1510-28 DGS-1510-28P Hardware-based DGS-1510-28X DGS-1510-28XMP Software-based Port 1 to 8 V Port 9 to 28 V Model Name DGS-1510-52 ERPS Hardware-based Software-based Port 1 to 8 V Port 9 to 24 Port 25 to 32 Port 33 to 52 V V V Model Name DGS-1510-52X (HW
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386
  • 387
  • 388
  • 389
  • 390
  • 391
  • 392
  • 393
  • 394
  • 395
  • 396
  • 397
  • 398
  • 399
  • 400
  • 401
  • 402
  • 403
  • 404
  • 405
  • 406
  • 407
  • 408
  • 409
  • 410
  • 411
  • 412
  • 413
  • 414
  • 415
  • 416
  • 417
  • 418
  • 419
  • 420
  • 421
  • 422
  • 423
  • 424
  • 425
  • 426
  • 427
  • 428
  • 429
  • 430
  • 431
  • 432
  • 433
  • 434
  • 435
  • 436
  • 437
  • 438
  • 439
  • 440
  • 441
  • 442
  • 443
  • 444
  • 445
  • 446
  • 447
  • 448
  • 449
  • 450
  • 451
  • 452
  • 453
  • 454
  • 455
  • 456
  • 457
  • 458
  • 459
  • 460
  • 461
  • 462
  • 463
  • 464
  • 465
  • 466
  • 467
  • 468
  • 469
  • 470
  • 471
1