D-Link DGS-1250 Quick Install Guide

D-Link DGS-1250 Manual

D-Link DGS-1250 manual content summary:

  • D-Link DGS-1250 | Quick Install Guide - Page 1
  • D-Link DGS-1250 | Quick Install Guide - Page 2
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Information in this document is subject to change without notice. Reproduction in any manner whatsoever, without the written permission of D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link
  • D-Link DGS-1250 | Quick Install Guide - Page 3
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Table of Contents Intended Readers ...v Typographical Conventions ...v Notes and Cautions ...v 1. Introduction ...1 Switch Description ...1 Package Contents ...1 Features ...1 Front Panel Components...2 Ports ...3
  • D-Link DGS-1250 | Quick Install Guide - Page 4
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Safety/Sécurité ...34 Safety Instructions ...34 Safety Cautions ...34 Consignes de sécurité ...35 Précautions de sécurité ...35 General Precautions for Rack-Mountable Products 36 Protecting Against Electrostatic
  • D-Link DGS-1250 | Quick Install Guide - Page 5
    Readers The DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide contains detailed information about the hardware specifications of the switches in this series. It also contains brief information on how to configure and manage a switch in this series. This manual is
  • D-Link DGS-1250 | Quick Install Guide - Page 6
    , please contact your local D-Link reseller for replacement. Features The list of features below highlights the significant features of the Switch.  Supports a 16K MAC address table (for DGS-1250-28X/28XMP); supports a 32K MAC address table (for DGS1250-52X/52XMP).  Supports Flow Control (802.3x
  • D-Link DGS-1250 | Quick Install Guide - Page 7
    Supports Port-based VLAN.  Supports Asymmetric VLAN.  Supports Auto Voice and Surveillance VLAN.  Supports IP Interfaces with up to 4 IP interfaces.  Supports Static Routing.  Supports Quality of Service button (only of PoE supported switches). Figure 1-1 Front panel view of the DGS-1250-28X 2
  • D-Link DGS-1250 | Quick Install Guide - Page 8
    . 10/100/1000 Mbps RJ45 Ports The DGS-1250-28X and DGS-1250-52X Switches are equipped with 24 or 48 RJ45 Ethernet ports. These ports can operate at 10 Mbps, 100 Mbps, and 1 Gbps wirespeeds. 10/100/1000 Mbps RJ45 PoE The DGS-1250-28XMP and DGS-1250-52XMP Switches are equipped with 24 or Ports 48
  • D-Link DGS-1250 | Quick Install Guide - Page 9
    1-5 LED indicators for the DGS-1250-28X Figure 1-6 LED indicators for the DGS-1250-28XMP Figure 1-7 LED indicators for the DGS-1250-52X LED Power Console Fan Error PWR Max. DGS-1250-28XMP DGS-1250-52XMP Link/Act LEDs Figure 1-8 LED indicators for the DGS-1250-52XMP Description This LED will
  • D-Link DGS-1250 | Quick Install Guide - Page 10
    Ethernet Smart Managed Switch Hardware Installation Guide LED PoE DGS-1250-28XMP DGS-1250-52XMP Description RJ45 Ports: This LED will light solid green when there is a connection (or link) to a 1000 Mbps Ethernet device or solid amber when there is a connection (or link) to a 10/100 Mbps Ethernet
  • D-Link DGS-1250 | Quick Install Guide - Page 11
    Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Figure 1-11 Rear panel view of the DGS-1250-52X Figure 1-12 Rear panel view of the DGS-1250-52XMP Components that can be found on the rear or even severely damaged components. Figure 1-13 Side panels of the DGS-1250-28X 6
  • D-Link DGS-1250 | Quick Install Guide - Page 12
    Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Figure 1-14 Side panels of the DGS-1250-28XMP Figure 1-15 Side panels of the DGS-1250-52X Figure 1-16 Side panels of the DGS-1250-52XMP Smart Fans The DGS-1250 Series Switches includes smart fans that will automatically change
  • D-Link DGS-1250 | Quick Install Guide - Page 13
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide o Low Speed to High Speed at 51°C o High Speed to Low Speed at 46°C 8
  • D-Link DGS-1250 | Quick Install Guide - Page 14
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide 2. Installation Installation Guidelines Installing the Switch feet to the Switch Install the Switch on a sturdy, level surface that can support the weight of the Switch (see the Weight section in Appendix A - Technical
  • D-Link DGS-1250 | Quick Install Guide - Page 15
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide within 1.82 meters (6 feet) of the Switch. Make sure that there is proper heat dissipation from +) ports that can be used to connect various other networking devices to this switch that do not support the standard 10
  • D-Link DGS-1250 | Quick Install Guide - Page 16
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide RJ45 wiring connection. These ports ports. Figure 2-4 Inserting transceivers into the transceiver ports The SFP/SFP+ ports also support other transceiver form factors like SFP and SFP+ transceivers. A complete list of
  • D-Link DGS-1250 | Quick Install Guide - Page 17
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Power On (AC Power) Plug one end of the AC power cord into the power socket of the Switch and the other end into the
  • D-Link DGS-1250 | Quick Install Guide - Page 18
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Slide the retainer through the tie wrap until the end of the cord. Figure 2-7 Slide the Retainer through the Tie Wrap Circle the tie of
  • D-Link DGS-1250 | Quick Install Guide - Page 19
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Fasten the tie of the retainer until the power cord is secured. Figure 2-9 Secure the power cord 14
  • D-Link DGS-1250 | Quick Install Guide - Page 20
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide 3. Switch Connections Switch to an End to the Switch via a twisted pair Category 5e UTP/STP cable.  Connect a switch supporting an optical fiber uplink to the Switch's SFP/SFP+ ports via fiber optical cabling. Figure
  • D-Link DGS-1250 | Quick Install Guide - Page 21
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Switch to a Server The Switch is ideal for connecting to a network backbone, server, or server farm. The RJ45ports operate at a speed of 10/100/1000
  • D-Link DGS-1250 | Quick Install Guide - Page 22
    some of switch management features. For more information about the CLI, refer to the DGS-1250 Series CLI Reference Guide. SNMP-based Management The Switch can be managed with an SNMP-compatible console program. The Switch supports SNMP v1, SNMPv2c and SNMPv3. The SNMP agent decodes the incoming SNMP
  • D-Link DGS-1250 | Quick Install Guide - Page 23
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide  Set the data format to 8 data bits, 1 stop will be displayed. Connecting to the Switch for the First Time The Switch supports user-based security that can prevent unauthorized users from accessing the Switch or
  • D-Link DGS-1250 | Quick Install Guide - Page 24
    each entry. The CLI prompt will immediately be available, as shown below. DGS-1250-28XMP Gigabit Ethernet Smart Managed Switch Command Line Interface Firmware: Build 2.01.001 Copyright(C) 2020 D-Link Corporation. All rights reserved. User Access Verification Username:admin Password:***** NOTE: For
  • D-Link DGS-1250 | Quick Install Guide - Page 25
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide In the above example,  Enter the configure operation, monitor performance, and detect potential problems in the Switch, switch group, or network. Managed devices that support SNMP include software (referred to as an
  • D-Link DGS-1250 | Quick Install Guide - Page 26
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Management Information Base (MIB) A Management management software. In addition to the standard MIB-II, the Switch also supports its own proprietary enterprise MIB as an extended Management Information Base. The
  • D-Link DGS-1250 | Quick Install Guide - Page 27
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide 5. Web-based Switch Configuration with the Switch using the HTTP or HTTPS (SSL) protocol. The following web browsers are supported:  Internet Explorer (version 8 and later)  Firefox  Google Chrome  Safari Logging
  • D-Link DGS-1250 | Quick Install Guide - Page 28
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide After pressing the Enter key, the following authentication window should appear, as shown below. UI of the Switch are explained in the chapters below. NOTE: The Switch only supports ASCII characters for input values. 23
  • D-Link DGS-1250 | Quick Install Guide - Page 29
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Web User Interface (Web UI) The Some management functions like port monitoring are also accessible here. Click the D-Link logo to go to the D-Link website. AREA 2 In this area is a toolbar used to access functions
  • D-Link DGS-1250 | Quick Install Guide - Page 30
    AREA 4 DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide In this area, configuration are described in the table below. Area Number Function AREA 1 Click the D-Link logo to go to the D-Link website. AREA 2 In this area is a toolbar used to access functions like
  • D-Link DGS-1250 | Quick Install Guide - Page 31
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide The status of devices, IP cameras, and NVRs discovered on the switch will also be displayed in this area. 26
  • D-Link DGS-1250 | Quick Install Guide - Page 32
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Appendix A - Technical DGS-1250-28X: 1 fan DGS-1250-28XMP: 2 fans DGS-1250-52X: 1 fan DGS-1250-52XMP: 2 fans Maximum Power Consumption: DGS-1250-28X: 30.6 Watts (100 VAC), 29.6 Watts (240 VAC) DGS-1250-28XMP:
  • D-Link DGS-1250 | Quick Install Guide - Page 33
    , 1 U Rack-mount size DGS-1250-28X: 1.75 kg DGS-1250-28XMP: 3.46 kg DGS-1250-52X: 3.01 kg DGS-1250-52XMP: 3.85 kg DGS-1250-28X: 743482.4543 Hours (with AC power) DGS-1250-28XMP: 463430.1638 Hours (with AC power) DGS-1250-52X: 589984.721 Hours (with AC power) DGS-1250-52XMP: 309053.1045 Hours (with
  • D-Link DGS-1250 | Quick Install Guide - Page 34
    Switch Hardware Installation Guide Feature Priority Queues MAC Address Table Description DGS-1250-28XMP: 95.24 Mpps DGS-1250-52X: 130.95 Mpps DGS-1250-52XMP: 130.95 Mpps 8 Priority Queues per port. DGS-1250-28X: 16K DGS-1250-28XMP: 16K DGS-1250-52X: 32K DGS-1250-52XMP: 32K Supports 256 Static MAC
  • D-Link DGS-1250 | Quick Install Guide - Page 35
    Managed Switch Hardware Installation Guide Location LED DGS-1250-28XMP DGS-1250-52XMP LED per Link/Act SFP/SFP+ Support Half-Duplex and Full-Duplex operations  IEEE 802.3x Flow Control support for Full-Duplex mode  Back Pressure for Half-Duplex mode  Head-of-line blocking prevention  Manual
  • D-Link DGS-1250 | Quick Install Guide - Page 36
    Smart Managed Switch Hardware Installation Guide Feature PoE Ports DGS-1250-28XMP DGS-1250-52XMP Description  DEM-433XT (10GBASE-ER, single-mode, 40 km, without DDM)  DEM-434XT (10GBASE-ZR, single-mode, 80 km, without DDM) WDM (BiDi) SFP+ Transceivers Supported:  DEM-436XT-BXD (10GBASE-LR
  • D-Link DGS-1250 | Quick Install Guide - Page 37
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Appendix B - Cables and Connectors Ethernet Cable Console Cable (RJ45 to RS-232) Ethernet Cable When connecting the Switch to another switch, a bridge, or hub, a straight-
  • D-Link DGS-1250 | Quick Install Guide - Page 38
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Console Cable (RJ45 to RS-232) A console cable is used to connect to the RJ45 console port of the Switch to access the command line
  • D-Link DGS-1250 | Quick Install Guide - Page 39
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Safety/Sécurité Safety Instructions Consignes de sécurité General Precautions for Rack-Mountable Products Protecting Against Electrostatic Discharge Safety Instructions , contact your trained service provider.  Do not
  • D-Link DGS-1250 | Quick Install Guide - Page 40
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide pièce concernée ou contactez votre prestataire de services agréé.  Endommagement du câble d'alimentation, produit ne fonctionne pas correctement lorsque les instructions d'utilisation sont correctement suivies. Pré
  • D-Link DGS-1250 | Quick Install Guide - Page 41
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide  Ne versez pas de type de source d'alimentation est requis, consultez votre prestataire de services ou votre compagnie d'électricité.  Assurez-vous que les caract as to various peripherals or supporting hardware: 36
  • D-Link DGS-1250 | Quick Install Guide - Page 42
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide CAUTION: Installing systems in a rack components in the rack.  Do not step on or stand on any component when servicing other components in a rack. CAUTION: Never defeat the ground conductor or operate the equipment
  • D-Link DGS-1250 | Quick Install Guide - Page 43
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide  When transporting a sensitive component, first place it in an antistatic container or packaging.  Handle all sensitive components in a static-safe area. If possible, use antistatic
  • D-Link DGS-1250 | Quick Install Guide - Page 44
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Warranty 39
  • D-Link DGS-1250 | Quick Install Guide - Page 45
    DGS-1250 Series Gigabit Ethernet Smart Managed Switch Hardware Installation Guide Technical Support 40
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45