D-Link DCH-Z120 User Guide

D-Link DCH-Z120 Manual

Get D-Link DCH-Z120 PDF manuals and user guides View all D-Link DCH-Z120 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DCH-Z120 manual content summary:

  • D-Link DCH-Z120 | User Guide - Page 1
    RF range, improve about 10 meters in indoor. •Support 100 Kbps transmit speed, speed up communication. Function Compare DCH-Z110/DCH-Z120 DCH-Z110 DCH-Z120 PIR Door/Window Temperature Illumination V V V V V V The sensor DCH-Z110/Z120 have PIR or door/window integrated with, temperature
  • D-Link DCH-Z120 | User Guide - Page 2
    support 8 nodes maximum. •Failed or success in add/remove the node ID can be viewed from ZWaveTM Controller. Notice 1: Always RESET interval step is 30 minutes. If the user want to wake-up the device immediately, please event and also report the battery status, temperature and illumination level
  • D-Link DCH-Z120 | User Guide - Page 3
    (0x03) Sensor Binary Report (V2) Sensor Type: Tamper (0x08) Sensor Value: 0xFF Notification Report (V4) Notification Type: Home Security (0x07) Event: Motion Detection, Unknown Location (0x08) Sensor Binary Report (V2) Sensor Type: Motion (0x0C) Sensor Value: 0xFF * Door/Window Report: When the
  • D-Link DCH-Z120 | User Guide - Page 4
    one minute. And please notice if setting this value to zero, that means disable all of the timing report except the low battery detection. The device supports the Z-Wave firmware update via OTA. Before starting the procedure, please remove the front cover of the device. Otherwise the hardware check
  • D-Link DCH-Z120 | User Guide - Page 5
    user power up the device. Caution: After remove the battery, please wait about 30 seconds, and then re-install the battery. Security Network temperature and the illumination level. The user setting by the configuration NO. 9. The device supports the security function. When the device included with
  • D-Link DCH-Z120 | User Guide - Page 6
    6
  • D-Link DCH-Z120 | User Guide - Page 7
    the device report the low battery message. The user should replace the battery to new one. The battery type is CR123A, 3.0V. battery and install the cover back. 1.Put the front cover bottom to 1-1, and press down. Choosing a Suitable Location 1.The recommended mounting height is 160cm for DCH-Z120
  • D-Link DCH-Z120 | User Guide - Page 8
    Notice: * All of the configuration, the data size is 1. * The configuration mark with star(*), means after the remove the setting still keep, don't reset to factory default. Unless the user execute the "RESET" procedure. * The reserve bit or not supported bit is allowed any value, but no effect. 8
  • D-Link DCH-Z120 | User Guide - Page 9
    NO. Name Def. Valid A B Description Setting the BASIC command value to turn on the light. The 0xFF(-1) means   2 Basic Set Level 0xFF All turn on the light. For dimmer equipment 1 to 100 means the light strength. 0 means turn off the light. PIR sensitivity settings. 0 means disable the
  • D-Link DCH-Z120 | User Guide - Page 10
    . (1:Disable, 0:Enable) Bit4: Notification Type, 0  0: Using Notification Report. 1: Using Sensor Binary Report. 0   Bit5: Disable Multi CC in auto report. (1:Disable, 0:Enable) 0   Bit6: Disable to report battery state when the device triggered. (1:Disable, 10
  • D-Link DCH-Z120 | User Guide - Page 11
    default tick is 3 (24 seconds). Setting the suitable value to prevent   3 1 ~ 127 received the trigger signal too frequently. Also can save the battery energy. Notice: If this value bigger than the configuration setting NO. 9. There is a period after the light turned off and the PIR not
  • D-Link DCH-Z120 | User Guide - Page 12
    Note: Refer A as DCH-Z110, B as DCH-Z120 Description Z-Wave Supported Command Class COMMAND_CLASS_ZWAVEPLUS_INFO_V2 COMMAND_CLASS_BATTERY COMMAND_CLASS_NOTIFICATION_V4 COMMAND_CLASS_MARK COMMAND_CLASS_BASIC Specifications Power by CR123A lithium battery. Signal (Frequency): 868.40 MHz, 869
  • D-Link DCH-Z120 | User Guide - Page 13
    and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
DCH-Z110/Z120
The sensor DCH-Z110/Z120 have PIR or door/window integrated with,
temperature and illumination, which are 3 sensors function in one,
based on Z-Wave
TM
technology.
It is the Z-Wave
TM
plus product, it supports the security, OTA... Those
newest features of the Z-Wave
TM
technology. Z-Wave
TM
is a wireless
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
TM
network
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications.
All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
TM
500 series chip, when your Z-Wave
TM
network system is all made by Z-Wave
TM
500 series devices. The
network system will have the advantages as below.
•
Concurrent multi-channel support reduces external interference.
•
Better RF range, improve about 10 meters in indoor.
•
Support 100 Kbps transmit speed, speed up communication.
Function Compare DCH-Z110/DCH-Z120
PIR
Door/Window
Temperature
Illumination
DCH-Z110
V
V
V
DCH-Z120
V
V
V
Add to/Remove from Z-Wave
TM
Network
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-Wave
TM
network.
In the first time, add the device into the Z-Wave
TM
network.
First,
make sure the primary controller is in the add mode. And then power
on the device, just take out the insulation Mylar in the back side of the
device. The device will auto start the NWI (Network Wide Inclusion)
mode. And it should be included in 5 seconds. You will see the LED
light ON one second.
1