D-Link DAP-3320 Quick Install Guide
D-Link DAP-3320 Manual
 |
View all D-Link DAP-3320 manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DAP-3320 manual content summary:
- D-Link DAP-3320 | Quick Install Guide - Page 1
- D-Link DAP-3320 | Quick Install Guide - Page 2
Contents • DAP-3320 Wireless PoE Outdoor Access Point • Grounding Wire • Wall Mounting Bracket/Kit • CD (with software and user manual) Note the unit, use a D-Link PoE switch or the D-Link DPE-301GI PoE injector (not included). * Maximum Wireless signal rate derived from IEEE DAP-3320 Install Guide - D-Link DAP-3320 | Quick Install Guide - Page 3
ncluded). 2 1 3 4 Press and hold for six seconds to reset the access point 1 Reset Button to the factory default settings. The LED will turn on for two seconds and then begin the reboot grounding wire to help prevent device damage due to shorts and lightning strikes. DAP-3320 Install Guide 3 - D-Link DAP-3320 | Quick Install Guide - Page 4
Link product warranty void and may also expose the end user or the service provider to legal and financial liabilities. D-Link especially when there are electric power and phone lines. 2. When installing your access point, note the following: • Do not use a metal ladder. • Do DAP-3320 Install Guide - D-Link DAP-3320 | Quick Install Guide - Page 5
Installation 1. Lift the release tab in the middle of the cover, then pull the cover off. 2. Connect an Ethernet cable (not included) to the Ethernet port. DAP-3320 Install Guide 5 - D-Link DAP-3320 | Quick Install Guide - Page 6
3. Use the grounding screw to attach the grounding wire. 4. Reattach the cover. You may need to break off one of the plastic port covers to allow your cables to exit the AP. 6 DAP-3320 Install Guide - D-Link DAP-3320 | Quick Install Guide - Page 7
Mounting The DAP-3320 supports the IP55 water/dustproof standard. It is recommended that you place the AP under a roof, shelter, or weatherproof container in severe weather environments. It is highly recommended that you configure and test your access point before mounting it. Pole Mount Thread the - D-Link DAP-3320 | Quick Install Guide - Page 8
Wall Mount Screw the wall mounting bracket into the wall, then attach the Access Point to it. For extra security, you can thread the plastic mounting ties through the back of the Access Point and the wall mounting bracket as shown. 8 DAP-3320 Install Guide - D-Link DAP-3320 | Quick Install Guide - Page 9
Connect to Your Network You can connect the DAP-3320 to a PoE switch, or you can use a PoE injector to power the AP. Connecting to a PoE Switch Connect the Ethernet cable that is connected to the DAP-3320 to your PoE switch. DAP-3320 PoE Switch DAP-3320 Install Guide 9 - D-Link DAP-3320 | Quick Install Guide - Page 10
PoE Injector 1. Connect the Ethernet cable that is connected to the DAP-3320 to the P+DATA OUT port on the PoE injector. 2. Connect the PoE Injector, and plug it into an electrical outlet. DAP-3320 PoE Injector* Power Adapter* PC Switch or Router * Power adapter and PoE injector are not included. - D-Link DAP-3320 | Quick Install Guide - Page 11
continue. Step 3: After the home page appears, go to Basic Settings > LAN to change the IP settings of the DAP-3320. Go to Basic Settings > Wireless to configure your wireless settings. Note: Make sure you click on Configuration > Save and Activate to save your settings. DAP-3320 Install Guide 11 - D-Link DAP-3320 | Quick Install Guide - Page 12
) 361-5265 World Wide Web http://support.dlink.ca Version 1.00(US)_90x130 February 17, 2016 6AP3320Q..01G Copyright ©2016 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
