D-Link 3324SRi Reference Manual
D-Link 3324SRi - Switch - Stackable Manual
 |
UPC - 790069256042
View all D-Link 3324SRi manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link 3324SRi manual content summary:
- D-Link 3324SRi | Reference Manual - Page 1
xStack High-density Layer 3 Intelligent Gigabit Switch Command Line Interface Reference Manual Release IV First Edition (October 2004) 6XSTACKCLI01 RECYCLABLE - D-Link 3324SRi | Reference Manual - Page 2
digung hervorrufen. 17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren Servicepartner. Somit stellen Sie die INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY - D-Link 3324SRi | Reference Manual - Page 3
D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall never be responsible for any software, firmware, service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list of D-Link offices is provided at the back of this manual - D-Link 3324SRi | Reference Manual - Page 4
addresses with an APO or FPO. Limited Warranty: D-Link warrants that the hardware portion of the D-Link of the Warranty Period to an Authorized DLink Service Office. The customer must submit as include any manuals or accessories in the shipping package. D-Link will only replace the defective portion - D-Link 3324SRi | Reference Manual - Page 5
, please contact corresponding local D-Link office. Register online your D-Link product at http://support.dlink.com/register/ D-Link Offices for Registration and Warranty Service The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To obtain an RMA - D-Link 3324SRi | Reference Manual - Page 6
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference - D-Link 3324SRi | Reference Manual - Page 7
32 Switch Utility Commands ...54 Network Monitoring Commands ...60 Multiple Spanning Tree Protocol (MSTP) Commands 77 Forwarding Database Commands...91 Broadcast Storm Control Commands 101 QoS Commands ...103 Port Mirroring Commands ...116 VLAN Commands ...120 Link Aggregation Commands...130 IP - D-Link 3324SRi | Reference Manual - Page 8
Commands ...284 DNS Relay Commands ...288 RIP Commands ...292 DVMRP Commands...295 PIM Commands...300 IP Multicasting Commands ...304 MD5 Configuration Commands ...306 OSPF Configuration Commands ...309 Route Preference Commands ...330 Jumbo Frame Commands ...334 File System Commands...336 Command - D-Link 3324SRi | Reference Manual - Page 9
Interface (CLI) can be used to configure and manage the Switch via the serial port or Telnet interfaces. This manual provides a reference for all of the commands contained in the CLI for members of the xStack family, including the DGS-3324SRi, DGS-3324SR, DXS-3326GSR and the DXS-3350SR. Examples - D-Link 3324SRi | Reference Manual - Page 10
Manual Setting the Switch's IP Address Each switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other TCP/IP application (for example BOOTP, TFTP). The Switch's default IP address is 10.90.90.90. You can change the default switch IP address - D-Link 3324SRi | Reference Manual - Page 11
Command Line Interface Manual Figure 1-3. Assigning an IP Address In the above example, the Switch was assigned an IP address of 10.53.13.144 with a subnet mask of 255.0.0.0. The system message Success indicates that the command was executed successfully. The Switch can now be configured and managed - D-Link 3324SRi | Reference Manual - Page 12
that allows the user to connect to the Switch's management agent via a serial port and a terminal or a computer running a terminal emulation program. The console can also be used over the network using the TCP/IP Telnet protocol. The console program can be used to configure the Switch to use an - D-Link 3324SRi | Reference Manual - Page 13
xStack Gigabit Layer 3 Switch Command Line Interface Manual Figure 2-1. Initial Console Screen Commands are entered at the command prompts, DGS-3324SRi:4#, DGS-3324SR:4#, DXS-3326GSR:4#, DXS-3350SR:4#. There are a number of helpful features included in the CLI. Entering the ? command will display a - D-Link 3324SRi | Reference Manual - Page 14
xStack Gigabit Layer 3 Switch Command Line Interface Manual Figure 2-3. Example Command Parameter Help In this case, the command config account enter the previous command (config account) at the command prompt. Now the appropriate User name can be entered and the config account command re-executed. 6 - D-Link 3324SRi | Reference Manual - Page 15
xStack Gigabit Layer 3 Switch Command Line Interface Manual All commands in the CLI function in this way. In addition, the syntax of the help prompts are the same as presented in this manual − angle brackets < > indicate a numerical value or character string, braces { } indicate optional parameters - D-Link 3324SRi | Reference Manual - Page 16
3 Switch Command Line Interface Manual In the above example, all of the possible next parameters for the show command are displayed. At the next command prompt, the up arrow was used to re-enter the show command, followed by the account parameter. The CLI then displays the user accounts configured - D-Link 3324SRi | Reference Manual - Page 17
Switch Command Line Interface Manual 3 COMMAND SYNTAX The following symbols are used to describe how command entries are made and values and arguments are specified in this manual an IP interface name in the space, a VLAN name in the space, and the network address in - D-Link 3324SRi | Reference Manual - Page 18
xStack Gigabit Layer 3 Switch Command Line Interface Manual {braces} Purpose Syntax Description Example command Encloses , the command previous to that displayed appears. This way it is possible to review the command history for the current session. Use the down arrow to progress sequentially - D-Link 3324SRi | Reference Manual - Page 19
show config show session show switch show switch_mode show device status show module_info show serial_port config serial_port enable clipaging disable clipaging enable telnet disable telnet enable web disable web save reboot reset login logout [admin | user] - D-Link 3324SRi | Reference Manual - Page 20
"dlink". DGS-3324SRi:4#create account admin dlink Command: create account admin dlink Enter a case-sensitive new password:**** Enter the new password again for confirmation:**** Success. DGS-3324SRi:4# config account Purpose Syntax Description Parameters Restrictions Used to configure user - D-Link 3324SRi | Reference Manual - Page 21
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#config account dlink Command: config account dlink Enter a old password:**** Enter a case-sensitive new password:**** Enter the new password again for confirmation:**** Success. DGS-3324SRi:4# show account Purpose Syntax - D-Link 3324SRi | Reference Manual - Page 22
usage: DGS-3324SRi:4# To delete the user account "System2": DGS-3324SRi:4#delete account System2 Command: delete account System2 Success. DGS-3324SRi:4# show config Purpose Syntax Description Parameters Restrictions Used to display a list of configuration commands entered into the Switch. show - D-Link 3324SRi | Reference Manual - Page 23
Switch Command Line Interface Manual Command: show config config_in_NVRAM # DGS-3324SRi Configuration # # Firmware: Build 4.00-B13 # Copyright(C) 2004-2007 D-Link a list of currently logged-in users. show session This command displays a list of all the users that are logged-in at the - D-Link 3324SRi | Reference Manual - Page 24
show switch Command: show switch Device Type : DGS-3324SRi Stackable Ethernet Switch Unit ID : 1 MAC Address : DA-10-21-00-00-01 IP Address : 10.41.44.22 (Manual) VLAN Name : default Subnet Mask : 255.0.0.0 Default Gateway : 0.0.0.0 Boot PROM Version : Build 2.01-B01 Firmware Version - D-Link 3324SRi | Reference Manual - Page 25
xStack Gigabit Layer 3 Switch Command Line Interface Manual SSL Status : Disabled SSH Status : Disabled 802.1x : Disabled IP Management : Disabled Dual Image : Supported DGS-3324SRi:4# show switch_mode Purpose Syntax Description Parameters Restrictions Used to display the current switch - D-Link 3324SRi | Reference Manual - Page 26
3 Switch Command Line Interface Manual To show the current hardware status of the Switch: DGS-3324SRi:4#show DGS-3324SR and the DGS-3324SRi do not support the optional module, information about the module can be viewed on these switches if they are stacked with one of the switches that support - D-Link 3324SRi | Reference Manual - Page 27
xStack Gigabit Layer 3 Switch Command Line Interface Manual 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - DGS-3324SRi:4# config serial_port Purpose Syntax Description Parameters Used to configure The user may select a time period from the following list which the Switch will - D-Link 3324SRi | Reference Manual - Page 28
. • 15_minutes − The console will log out the current user if there is no user input for 15 minutes. Restrictions Only administrator-level users can issue this command. Example usage: To configure baud rate: DGS-3324SRi:4#config serial_port baud_rate 115200 Command: config serial_port baud_rate - D-Link 3324SRi | Reference Manual - Page 29
xStack Gigabit Layer 3 Switch Command Line Interface Manual disable clipaging Purpose Syntax Telnet protocol is 23. Only administrator-level users can issue this command. Example usage: To enable Telnet and configure port number: DGS-3324SRi:4#enable telnet 23 Command: enable telnet 23 - D-Link 3324SRi | Reference Manual - Page 30
1 and 65535. The "well-known" port for the Web-based management software is 80. Only administrator-level users can issue this command. Example usage: To enable HTTP and configure port number: DGS-3324SRi:4#enable web 80 Command: enable web 80 Note: SSL will be disabled if web is enabled. Success - D-Link 3324SRi | Reference Manual - Page 31
Switch. None. Only administrator-level users can issue this command. Example usage: To disable HTTP: DGS-3324SRi:4#disable web Command: disable web Success. DGS-3324SRi:4# save Purpose Syntax Description Parameters Restrictions Example usage: Used to save changes in the Switch's configuration - D-Link 3324SRi | Reference Manual - Page 32
used to restore the Switch's configuration to the default settings assigned from the factory. config − If the keyword 'config' is specified, all of the factory default settings are restored on the Switch including the IP address, user accounts, and the Switch history log. The Switch will not save or - D-Link 3324SRi | Reference Manual - Page 33
Layer 3 Switch Command Line Interface Manual Success. DGS-3324SRi:4# login Purpose Syntax Description Parameters Restrictions Used to log in a user to the Switch's console. login This command is used to initiate the login procedure. The user will be prompted for his Username and Password. None - D-Link 3324SRi | Reference Manual - Page 34
xStack Gigabit Layer 3 Switch Command Line Interface Manual 5 SWITCH PORT COMMANDS The switch port commands in the Command in the following sections. config ports Purpose Syntax Description Parameters Used to configure the Switch's Ethernet port settings. [ | all] {speed [auto | - D-Link 3324SRi | Reference Manual - Page 35
port description of the selected port(s). Only administrator-level users can issue this command. Example usage: To configure the speed of port 3 of unit 1 to be 10 Mbps, full duplex, learning and state enable: DGS-3324SRi:4#config ports 1:1-1:3 speed 10_full learning enable state enable Command - D-Link 3324SRi | Reference Manual - Page 36
Line Interface Manual To display the configuration of all ports on a standalone switch: DGS-3324SRi:4#show ports Command:show ports Port Port Settings Connection Address State Speed/Duplex/FlowCtrl Speed/Duplex/FlowCtrl Learning -------- 1:1 Enabled Auto/Enabled Link Down Enabled - D-Link 3324SRi | Reference Manual - Page 37
Configure port security for all ports on the Switch. admin_state [enable | disable] - Enable or disable port security for the listed ports. max_learning_addr - Use this to limit the number of MAC addresses addresses. The user has three choices: Permanent - The locked addresses - D-Link 3324SRi | Reference Manual - Page 38
xStack Gigabit Layer 3 Switch Command Line Interface Manual config port_security ports until the Switch has been reset. Restrictions Only administrator-level users can issue this command. Example usage: To configure the port security: DGS-3324SRi:4#config port_security ports 5:1-5:5 - D-Link 3324SRi | Reference Manual - Page 39
Gigabit Layer 3 Switch Command Line Interface Manual 1:7 Enabled 10 address of the entry to delete. Restrictions Only administrator-level users can issue this command. Example usage: To delete an entry from the port security list: DGS-3324SRi:4#delete port_security_entry_vlan_name default - D-Link 3324SRi | Reference Manual - Page 40
Switch Command Line Interface Manual 7 NETWORK MANAGEMENT (SNMP) COMMANDS The network management commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. The xStack family of switches support user delete snmp user show snmp user - D-Link 3324SRi | Reference Manual - Page 41
xStack Gigabit Layer 3 Switch Command Line Interface Manual Command delete snmp group show snmp ] priv [none | des ]]} The create snmp user command creates a new SNMP user and adds the user to an SNMP group that is also created by this command. SNMP ensures: Message - D-Link 3324SRi | Reference Manual - Page 42
Switch Command Line Interface Manual create snmp user Parameters Encryption − Scrambles the contents of messages to prevent it from being viewed by an unauthorized source. − An alphanumeric name of up to 32 characters that will identify the new SNMP user used. - - D-Link 3324SRi | Reference Manual - Page 43
an SNMP user on the Switch: DGS-3324SRi:4#create snmp user dlink default encrypted by_password auth md5 auth_password priv none Command: create snmp user dlink default encrypted by_password auth md5 auth_password priv none Success. DGS-3324SRi:4# delete snmp user Purpose Syntax Description - D-Link 3324SRi | Reference Manual - Page 44
the SNMP group username table. None. Only administrator-level users can issue this command. Example usage: To display the SNMP users currently configured on the Switch: DGS-3324SRi:4#show snmp user Command: show snmp user Username initial Group Name VerAuthPriv initial V3 None None Total - D-Link 3324SRi | Reference Manual - Page 45
an object tree (MIB tree) that will be deleted from the Switch. Only administrator-level users can issue this command. Example usage: To delete a previously configured SNMP view from the Switch: DGS-3324SRi:4#delete snmp view dlinkview all Command: delete snmp view dlinkview all Success - D-Link 3324SRi | Reference Manual - Page 46
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show snmp view Command: show snmp view Vacm a password to permit access to the agent on the Switch. One or more of the following characteristics can be associated with the community string: An Access List of IP addresses of - D-Link 3324SRi | Reference Manual - Page 47
string is used like a password to give remote SNMP managers access to MIB objects in the Switch's SNMP agent. Only administrator-level users can issue this command. Example usage: To delete the SNMP community string "dlink:" DGS-3324SRi:4#delete snmp community dlink Command: delete snmp community - D-Link 3324SRi | Reference Manual - Page 48
Access Right dlink ReadView read_write private CommunityView read_write public CommunityView read_only Total Entries: 3 DGS-3324SRi:4# config snmp engineID Purpose Syntax Description Parameters Restrictions Used to configure a name for the SNMP engine on the Switch. config snmp - D-Link 3324SRi | Reference Manual - Page 49
Switch: DGS-3324SRi:4#show snmp engineID Command: show snmp engineID SNMP Engine ID : 0035636666 DGS-3324SRi:4# create snmp group Purpose Syntax Description Parameters Used to create a new SNMP group, or a table that maps SNMP users used. The SNMP v2c supports both centralized and distributed - D-Link 3324SRi | Reference Manual - Page 50
xStack Gigabit Layer 3 Switch Command Line Interface Manual create snmp group Restrictions Authentication − Determines if an by the Switch's SNMP agent. Only administrator-level users can issue this command. Example usage: To create an SNMP group named "sg1:" DGS-3324SRi:4#create snmp - D-Link 3324SRi | Reference Manual - Page 51
Gigabit Layer 3 Switch Command Line Interface Manual delete snmp group Restrictions Only administrator-level users can issue this command. Example usage: To delete the SNMP group named "sg1". DGS-3324SRi:4#delete snmp group sg1 Command: delete snmp group sg1 Success. DGS-3324SRi:4# show snmp - D-Link 3324SRi | Reference Manual - Page 52
xStack Gigabit Layer 3 Switch Command Line Interface Manual Notify View Name Security Model Security Level : NotifyView : SNMPv3 : authNoPriv Group Name Model Security Level : WriteGroup : CommunityView : CommunityView : CommunityView : SNMPv2 : NoAuthNoPriv Total Entries: 10 DGS-3324SRi:4# 44 - D-Link 3324SRi | Reference Manual - Page 53
32> The create snmp host command creates a recipient of SNMP traps generated by the Switch's SNMP agent. − The IP address of the remote management station that will serve as the SNMP host for the Switch. v1 - Specifies that SNMP version 1 will be used. The Simple Network Management Protocol - D-Link 3324SRi | Reference Manual - Page 54
Success. DGS-3324SRi:4# show snmp host Purpose Syntax Description Parameters Restrictions Used to display the recipient of SNMP traps generated by the Switch's SNMP agent. show snmp host {} The show snmp host command is used to display the IP addresses and configuration information of - D-Link 3324SRi | Reference Manual - Page 55
nothing to prevent any IP address from accessing the Switch, provided the user knows the Username and Password. − The IP address of the trusted host. Only administrator-level users can issue this command. Example usage: To create the trusted host: DGS-3324SRi:4#create trusted_host 10.48 - D-Link 3324SRi | Reference Manual - Page 56
3 Switch Command Line Interface Manual show trusted_host Parameters None. Restrictions None. Example Usage: To display the list of trust hosts: DGS-3324SRi:4#show trusted_host Command: show trusted_host Management Stations IP Address 10.53.13.94 Total Entries: 1 DGS-3324SRi:4# delete - D-Link 3324SRi | Reference Manual - Page 57
Success. DGS-3324SRi:4# show snmp traps Purpose Used to show SNMP trap support on the Switch . Syntax show snmp traps Description This command is used to view the SNMP trap support status currently configured on the Switch. Parameters None. Restrictions Only administrator-level users can - D-Link 3324SRi | Reference Manual - Page 58
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show snmp traps Command: show snmp traps SNMP Traps : Enabled Authenticate Traps : Enabled DGS-3324SRi:4# disable snmp traps Purpose Used to disable SNMP trap support on the Switch. Syntax disable snmp traps - D-Link 3324SRi | Reference Manual - Page 59
Switch Command Line Interface Manual DGS-3324SRi:4#disable snmp authenticate_traps Command: disable snmp authenticate_traps Success. DGS-3324SRi:4# -level users can issue this command. Example usage: To configure the Switch contact to "M I S D e p a r t m e n t I I ": DGS-3324SRi:4#config - D-Link 3324SRi | Reference Manual - Page 60
administrator-level users can issue this command. Example usage: To configure the Switch name for "DGS-3324SRi Stackable Switch ": DGS-3324SRi:4#config snmp system_name DGS-3324SRi Stackable Switch Command: config snmp system_name DGS-3324SRi Stackable Switch Success. DGS-3324SRi:4# enable - D-Link 3324SRi | Reference Manual - Page 61
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#enable rmon Command: enable rmon Success. DGS-3324SRi:4# disable rmon Purpose Syntax Description Parameters Restrictions Used to disable RMON on the Switch. disable rmon This command is used, in conjunction with the enable - D-Link 3324SRi | Reference Manual - Page 62
Manual 8 SWITCH UTILITY COMMANDS The switch utility commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Please note that commands concerning the CompactFlash card (cfg_fromCf, firmware_to CF, etc.) are specific to the DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 63
parameters will remain unchanged. The TFTP server must be on the same IP subnet as the Switch. Only administrator-level users can issue this command. Example usage: To download a configuration file: DGS-3324SRi:4#download cfg_to TFTP 10.48.74.121 c:\cfg\setting.txt Command: download cfg_to TFTP - D-Link 3324SRi | Reference Manual - Page 64
of the firmware located on the Switch. This parameter is only used for the firmware_toCF parameter. The TFTP server must be on the same IP subnet as the Switch. Only administrator-level users can issue this command. Example usage: To upload a configuration file: DGS-3324SRi:4#upload cfg_toTFTP - D-Link 3324SRi | Reference Manual - Page 65
level users can issue this command. Example usage: To delete a firmware from the Switch's memory: DGS-3324SRi:4#config firmware image_id 2 delete Command: config firmware image_id 2 delete Success. Example usage: DGS-3324SRi:4# To configure a firmware as the boot up runtime image firmware: DGS - D-Link 3324SRi | Reference Manual - Page 66
3 Switch Command Line Interface Manual DGS-3324SRi:4#show firmware information Command: show firmware information Box ID --- -1 *1 1 2 Version -------4.00-B02 3.00-B13 Size(B) Update Time 2360471 00000 days 00:00:00 1052372 00000 days 00:00:56 From Serial Port (PROM) 10.53.13.94 User Unknown - D-Link 3324SRi | Reference Manual - Page 67
will send probe packets to the next hop on the intended traceroute path. The default is 1. None. Example usage: To trace the routed path between the Switch and 10.48.74.121. DGS-3324SRi:4#traceroute 10.48.74.121 p r o b e 3 Command: traceroute 10.48.74.121 p r o b e 3 1 - D-Link 3324SRi | Reference Manual - Page 68
xStack Gigabit Layer 3 Switch Command Line Interface Manual 9 NETWORK MONITORING COMMANDS The network monitoring commands Syntax Description Used to display statistics about the packets sent and received by the Switch. show packet ports This command is used to display statistics about - D-Link 3324SRi | Reference Manual - Page 69
number 2, port 4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical order. Restrictions None. Example usage: To display the packets analysis for port 7 of module 2: DGS-3324SRi:4#show packet port 2:7 Port number : 2:7 (A) (B) Frame Size Frame - D-Link 3324SRi | Reference Manual - Page 70
xStack Gigabit Layer 3 Switch Command Line Interface Manual show error ports Restrictions None. Example usage: To display the errors of the port 3 of module 1: DGS-3324SRi:4#show errors ports 1:3 Command:show errors ports 1:3 CRC Error Undersize Oversize Fragment Jabber Drop Pkts RX Frames - D-Link 3324SRi | Reference Manual - Page 71
- 14% DGS-3324SRi:4# clear counters Purpose Syntax Description Parameters Used to clear the Switch's statistics counters. clear counters {ports } This command will clear the counters used by the Switch to compile statistics. − Specifies a range of ports to be configured. The - D-Link 3324SRi | Reference Manual - Page 72
Gigabit Layer 3 Switch Command Line Interface Manual clear counters Restrictions Only administrator-level users can issue this command. Example usage: To clear the counters: DGS-3324SRi:4#clear counters ports 2:7-2:9 Command: clear counters ports 2:7-2:9 Success. DGS-3324SRi:4# clear log - D-Link 3324SRi | Reference Manual - Page 73
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show log index 1-4 Command: show log index 1-4 Index Date Time Log Text 4 2000-03-02 01:54:53 Port 1:13 link up, 100Mbps FULL duplex 3 2000-03-02 01:54:53 Spanning Tree Protocol is enabled 2 2000-03-02 01:54:53 Unit - D-Link 3324SRi | Reference Manual - Page 74
Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#disable syslog Command: disable syslog Success. DGS-3324SRi:4# show syslog Purpose indicates that the corresponding severity level is currently supported on the Switch. Numerical Severity Code 0 Emergency: system is unusable 66 - D-Link 3324SRi | Reference Manual - Page 75
xStack Gigabit Layer 3 Switch Command Line Interface Manual create syslog host 1 Alert: action must be taken immediately 2 Critical: critical indicates the facility values that the Switch currently supports. Numerical Facility Code 0 kernel messages 1 user-level messages 2 mail system 3 - D-Link 3324SRi | Reference Manual - Page 76
Gigabit Layer 3 Switch Command Line Interface Manual create syslog host the remote host. ipaddress − Specifies the IP address of the remote host where syslog messages will be sent -level users can issue this command. Example usage: To create syslog host: DGS-3324SRi:4#create - D-Link 3324SRi | Reference Manual - Page 77
Layer 3 Switch Command Line Interface Manual config syslog host Purpose Syntax Description Parameters Used to configure the syslog user-level" Facility. Those Facilities that have been designated are shown in the following: Bold font indicates the facility values the Switch currently supports - D-Link 3324SRi | Reference Manual - Page 78
xStack Gigabit Layer 3 Switch Command Line Interface Manual config syslog host 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 UUCP subsystem 9 - D-Link 3324SRi | Reference Manual - Page 79
Layer 3 Switch Command Line Interface Manual config syslog host host. ipaddress − Specifies the IP address of the administrator-level users can issue this command. Example usage: To configure a syslog host: DGS-3324SRi:4#config syslog supported on the Switch. Numerical Severity 71 - D-Link 3324SRi | Reference Manual - Page 80
xStack Gigabit Layer 3 Switch Command Line Interface Manual config syslog host all Code 0 Emergency: system is unusable 1 Alert: action indicates that the facility values the Switch currently supports. Numerical Facility Code 0 kernel messages 1 user-level messages 2 mail system 3 system - D-Link 3324SRi | Reference Manual - Page 81
xStack Gigabit Layer 3 Switch Command Line Interface Manual config syslog host all Restrictions 15 clock daemon 16 local use and disabled. Only administrator-level users can issue this command. Example usage: To configure all syslog hosts: DGS-3324SRi:4#config syslog host all severity all - D-Link 3324SRi | Reference Manual - Page 82
state enable Command: config syslog host all state enable Success. DGS-3324SRi:4# delete syslog host Purpose Syntax Description Parameters Restrictions Used to remove a syslog host, that has been previously configured, from the Switch. delete syslog host [ | all] The delete syslog host - D-Link 3324SRi | Reference Manual - Page 83
xStack Gigabit Layer 3 Switch Command Line Interface Manual To show syslog host information: DGS-3324SRi:4#show syslog host Command: show syslog host Syslog Global State: Disabled Host Id Host IP Address Severity 1 10.1.1.2 All 2 10.40.2.3 All 3 10.21.13.1 All Facility ------- - D-Link 3324SRi | Reference Manual - Page 84
destination, stated above, will instruct the switch to send informational, warning and critical events to the Switch's log or SNMP agent. Only administrator-level users can issue this command. Example usage: To configure the system severity: DGS-3324SRi:4#config system_severity trap critical - D-Link 3324SRi | Reference Manual - Page 85
config stp mst_config_id command as name ). b) A configuration revision number (named here as a revision_level) and; c) A 4096 element table (defined here as a vid_range) which will associate each of the possible 4096 VLANs supported by the Switch for a given instance. To utilize the MSTP - D-Link 3324SRi | Reference Manual - Page 86
xStack Gigabit Layer 3 Switch Command Line Interface Manual Command config stp priority Parameters - D-Link 3324SRi | Reference Manual - Page 87
Line Interface Manual DGS-3324SRi:4#disable stp Command: disable stp Success. DGS-3324SRi:4# config stp version Purpose Syntax Description Parameters Restrictions Used to globally set the version of STP on the Switch. config stp version [mstp | rstp | stp] This command allows the user to choose - D-Link 3324SRi | Reference Manual - Page 88
BPDU packets from other network devices when STP is disabled on the Switch. The default is enable. Only administrator-level users can issue this command. Example usage: To configure STP with maxage 18 and maxhops of 15: DGS-3324SRi:4#config stp maxage 18 maxhops 15 Command: config stp maxage 18 - D-Link 3324SRi | Reference Manual - Page 89
configuration messages by the designated port, to other devices on the bridged LAN, thus stating that the Switch is still functioning. The user may choose a time between 1 and 10 seconds. The default true indicates a point-to-point (P2P) shared link. P2P ports are similar to edge ports however they - D-Link 3324SRi | Reference Manual - Page 90
port list. The default is enable. Restrictions Only administrator-level users can issue this command. Example usage: To configure STP with path cost 19, hellotime set to 5 seconds, migration enable, and state enable for ports 1-5 of module 1. DGS-3324SRi:4#config stp ports 1:1-1:5 externalCost - D-Link 3324SRi | Reference Manual - Page 91
> - Specify the VID range from configured VLANs set on the Switch. Supported VIDs on the Switch range from ID number 1 to 4094. Only administrator-level users can issue this command. Example usage: To configure instance id 2 to add VID 10: DGS-3324SRi:4#config stp instance_id 2 add_vlan 10 Command - D-Link 3324SRi | Reference Manual - Page 92
user to delete a previously configured STP instance ID from the Switch. - Enter a value between 1 and 15 to identify the Spanning Tree instance on the Switch. Only administrator-level users can issue this command. Example usage: To delete stp instance id 2 from the Switch. DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 93
no name is entered, the default name will be the MAC address of the device. Only administrator-level users can issue this command. Example usage: To configure the MSTP region of the Switch with revision_level 10 and the name "Trinity": DGS-3324SRi:4#config stp mst_config_id revision_level 10 name - D-Link 3324SRi | Reference Manual - Page 94
Switch Command Line Interface Manual instance_id previously configured on the Switch. An entry interface. The default value is users can issue this command. Example usage: To designate ports 1 through 5 on module one, with instance ID 2, to have an auto internalCost and a priority of 16: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 95
Used to display the Switch's current STP configuration. show stp This command displays the Switch's current STP configuration. None. None. Example usage: To display the status of STP on the Switch: Status 1: STP enabled with STP compatible version DGS-3324SRi:4#show stp Command: show - D-Link 3324SRi | Reference Manual - Page 96
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4# show stp ports Purpose Syntax Description Parameters Restrictions Used to display the Switch's current instance_id configuration. show stp ports This command displays the STP Instance Settings and STP Instance - D-Link 3324SRi | Reference Manual - Page 97
Example usage: xStack Gigabit Layer 3 Switch Command Line Interface Manual To display the STP instance configuration for instance 0 (the internal CIST) on the Switch: DGS-3324SRi:4#show stp instance 0 Command: show stp instance 0 STP Instance Settings Instance Type Instance Status Instance - D-Link 3324SRi | Reference Manual - Page 98
Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show stp mst_config_id Command: show stp mst_config_id Current MST Configuration Identification Configuration Name : 00:53:13:1A:33:24 MSTI ID ------- CIST 1 Vid list ----------2-4094 1 Revision Level :0 DGS-3324SRi:4# 90 - D-Link 3324SRi | Reference Manual - Page 99
vlan_name 32> port This command will make an entry into the Switch's unicast MAC address forwarding database. − The name of the VLAN on which the MAC address resides. − The MAC address that will be added to the forwarding table. port − The port number - D-Link 3324SRi | Reference Manual - Page 100
01-00-00-00-00-01 Command: create multicast_fdb default 01-00-00-00-00-01 Success. DGS-3324SRi:4# config multicast_fdb Purpose Syntax Description Parameters Used to configure the Switch's multicast MAC address forwarding database. config multicast_fdb [add | delete - D-Link 3324SRi | Reference Manual - Page 101
2, port 4. 1:32:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical order. Only administrator-level users can issue this command. Example usage: To add multicast MAC forwarding: DGS-3324SRi:4#config multicast_fdb default 01-00-00-00-00-01 add 1:1-1:5 Command - D-Link 3324SRi | Reference Manual - Page 102
To delete a multicast fdb entry: DGS-3324SRi:4#delete fdb default 01-00-00-00-01-02 Command: delete fdb default 01-00-00-00-01-02 Success. DGS-3324SRi:4# clear fdb Purpose Syntax Used to clear the Switch's forwarding database of all dynamically learned MAC addresses. clear fdb [vlan - D-Link 3324SRi | Reference Manual - Page 103
all dynamic entries to the Switch's forwarding database. Only administrator-level users can issue this command. Example usage: To clear all FDB dynamic entries: DGS-3324SRi:4#clear fdb all Command: clear fdb all Success. DGS-3324SRi:4# show multicast_fdb Purpose Syntax Description Parameters - D-Link 3324SRi | Reference Manual - Page 104
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show multicast_fdb Command: show multicast_fdb VLAN Name MAC Address Egress Ports Mode : default : 01-00-5E-00-00-00 : 1:1-1:5,1:26,2:26 : Static Total Entries : 1 DGS-3324SRi:4# show fdb Purpose Syntax Description - D-Link 3324SRi | Reference Manual - Page 105
Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show fdb Command: show fdb Unicast MAC Address Aging Time = 300 VID VLAN Name MAC Address Port Type ------ 1 default 00-00-39-34-66-9A 1:12 Dynamic 1 default 00-00-51-43-70-00 1:12 Dynamic 1 default 00-00-5E - D-Link 3324SRi | Reference Manual - Page 106
Switch Command Line Interface Manual DGS-3324SRi:4#show ipfdb Command: show ipfdb Interface -----------System System System System System System System System System System System System System System System System System System System System IP Address user to define certain ports on the Switch - D-Link 3324SRi | Reference Manual - Page 107
xStack Gigabit Layer 3 Switch Command Line Interface Manual config fdb destination_hit ports Restrictions Only administrator-level users can issue this command. Example usage: To configure ports 1 to 5 as destination hit ports: DGS-3324SRi:4#config fdb destination_hit ports 1:1-1:5 enable - D-Link 3324SRi | Reference Manual - Page 108
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show fdb destination_hit ports 1:1-1:10 Command: show fdb destination_hit ports 1:1-1:10 Port # -------- 1:1 1:2 1:3 1:4 1:5 1:6 1:7 1:8 1:9 1:10 Destination Hit State Enabled Enabled Enabled Enabled Enabled Disabled - D-Link 3324SRi | Reference Manual - Page 109
xStack Gigabit Layer 3 Switch Command Line Interface Manual 12 BROADCAST STORM CONTROL COMMANDS The broadcast storm received by the Switch that will trigger the storm traffic control measures. Only administrator-level users can issue this command. Example usage: To configure traffic control and - D-Link 3324SRi | Reference Manual - Page 110
Success. DGS-3324SRi:4# show traffic control Purpose Syntax Description Parameters Restrictions Used to display current traffic control settings. show traffic control {group_list } This command displays the current storm traffic control configuration on the Switch. group_list - D-Link 3324SRi | Reference Manual - Page 111
xStack Gigabit Layer 3 Switch Command Line Interface Manual 13 QOS COMMANDS The xStack family of switches supports 802.1p priority queuing. These switches has eight classes of service for each port on the Switch, one of which is internal and unconfigurable to the user. These hardware classes of - D-Link 3324SRi | Reference Manual - Page 112
Switch Command Line Interface Manual before being allowed to transmit its accumulated packets. This establishes a Class of Service (CoS) for each of the Switch sections. config bandwidth_control Purpose Syntax Description Parameters Used to configure bandwidth control on a by-port basis. config - D-Link 3324SRi | Reference Manual - Page 113
xStack Gigabit Layer 3 Switch Command Line Interface Manual config bandwidth_control Restrictions − Specifies transmit. Only administrator-level users can issue this command. Example usage: To configure bandwidth control: DGS-3324SRi:4#config bandwidth_control 1:1-1:10 tx_rate - D-Link 3324SRi | Reference Manual - Page 114
DGS-3324SRi:4# config scheduling Purpose Syntax Description Used to configure traffic scheduling for each of the Switch's hardware priority classes. config scheduling {max_packet } The Switch contains seven hardware classes of service per device. The Switch's default - D-Link 3324SRi | Reference Manual - Page 115
-level users can issue this command. NOTICE: The default QoS scheduling arrangement is a strict priority schedule. To customize scheduling to set up weighted or round-robin class clearing, the max_packets values need to be changed. Example usage: To configure traffic scheduling: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 116
Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4# config scheduling 6 max_packet 0 Command: config scheduling 6 max_packet 0 Success. DGS-3324SRi:4# show scheduling Purpose Syntax Description Parameters Restrictions Used to display the currently configured traffic scheduling on - D-Link 3324SRi | Reference Manual - Page 117
− Specifies which of the Switch's hardware priority classes of service the 802.1p priority tags (specified above) will be mapped to. Only administrator-level users can issue this command. Example usage: To configure 802.1 user priority on the Switch: DGS-3324SRi:4# config 802.1p user_priority - D-Link 3324SRi | Reference Manual - Page 118
xStack Gigabit Layer 3 Switch Command Line Interface Manual show 802.1p user_priority Parameters Restrictions None. None. Example usage: To show 802.1p user priority: DGS-3324SRi:4# show 802.1p user_priority Command: show 802.1p user_priority COS Class of Traffic Priority-0 -> - D-Link 3324SRi | Reference Manual - Page 119
Example usage: xStack Gigabit Layer 3 Switch Command Line Interface Manual To configure 802.1p default priority on the Switch: DGS-3324SRi:4#config 802.1p default_priority all 5 Command: config 802.1p default_priority all 5 Success. DGS-3324SRi:4# show 802.1 default_priority Purpose Used to - D-Link 3324SRi | Reference Manual - Page 120
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4# show 802.1p default_priority Command: show 802.1p default_priority Port Priority ------- 1:1 1:2 1:3 1:4 1:5 1:6 1:7 1:8 1:9 1:10 1:11 1:12 1:13 1:14 1:15 1:16 1:17 1:18 1:19 1:20 1:21 1:22 1:23 1: - D-Link 3324SRi | Reference Manual - Page 121
of service will empty packets in a weighted roundrobin (WRR) order. That is to say that they will be emptied in an even distribution. Restrictions Only administrator-level users can issue this command. Example usage: To configure the traffic scheduling mechanism for each COS queue: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 122
Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show scheduling_mechanism Command: show scheduling_mechanism QOS scheduling_mechanism CLASS ID Mechanism Class-0 strict Class-1 strict Class-2 strict Class-3 strict Class-4 strict Class-5 strict Class-6 strict DGS-3324SRi:4# enable - D-Link 3324SRi | Reference Manual - Page 123
Example Usage: xStack Gigabit Layer 3 Switch Command Line Interface Manual To disable HOL prevention: DGS-3324SRi:4#disable hol_prevention Command: disable hol_prevention Success. DGS-3324SRi:4# show hol_prevention Purpose Used to show HOL prevention. Syntax show hol_prevention Description - D-Link 3324SRi | Reference Manual - Page 124
xStack Gigabit Layer 3 Switch Command Line Interface Manual 14 PORT MIRRORING COMMANDS The port sections. config mirror port add Purpose Syntax Description Parameters Used to configure a mirror port − source port pair on the Switch. config mirror port add source ports [rx - D-Link 3324SRi | Reference Manual - Page 125
xStack Gigabit Layer 3 Switch Command Line Interface Manual config mirror port add Restrictions The Target port cannot be listed as a source port. Only administrator-level users can issue this command. Example usage: To add the mirroring ports: DGS-3324SRi:4# config mirror port 1:10 add source - D-Link 3324SRi | Reference Manual - Page 126
, allows you to enter a port mirroring configuration into the Switch, and then turn the port mirroring on and off without having to modify the port mirroring configuration. None. None. Example usage: To enable mirroring configurations: DGS-3324SRi:4#enable mirror Command: enable mirror Success - D-Link 3324SRi | Reference Manual - Page 127
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#disable mirror Command: disable mirror Success. DGS-3324SRi:4# show mirror Purpose Syntax Description Parameters Restrictions Used to show the current port mirroring configuration on the Switch. show mirror This command - D-Link 3324SRi | Reference Manual - Page 128
pre-defined protocols for configuring protocol-based VLANs. The user may also choose a protocol that is not one of the fifteen defined protocols by properly configuring the userDefined protocol VLAN. The supported protocols for the protocol VLAN function on this Switch include IP, IPX, DEC, DEC LAT - D-Link 3324SRi | Reference Manual - Page 129
Switch Command Line Interface Manual create vlan Parameters user Switch supports 15 pre-configured protocol-based VLANs plus one user defined protocol based VLAN where the administrator may configure on the Switch include: protocol-ip - Using this parameter will instruct the Switch to forward - D-Link 3324SRi | Reference Manual - Page 130
Switch Command Line Interface Manual create vlan Corporation (DEC) Local Area Transport (LAT) protocol. protocol-decOther - Using this parameter will instruct the Switch Virtual Intergrated Network Service (VINES) Protocol. protocol-ipV6 - Using this parameter will instruct the Switch to forward - D-Link 3324SRi | Reference Manual - Page 131
vlan v1 tag 2 Command: create vlan v1 tag 2 Success. DGS-3324SRi:4# delete vlan Purpose Syntax Description Parameters Restrictions Example usage: To remove the vlan "v1": Used to delete a previously configured VLAN on the Switch. delete vlan This command will delete a previously - D-Link 3324SRi | Reference Manual - Page 132
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#delete vlan v1 Command: delete vlan v1 Success. DGS-3324SRi:4# config vlan add Purpose Syntax Description Parameters Restrictions Used to add additional ports to a previously configured VLAN. config vlan {[ - D-Link 3324SRi | Reference Manual - Page 133
-level users can issue this command. Example usage: To delete ports 5-7 of module 2 of the VLAN v1: DGS-3324SRi:4#config vlan v1 delete 2:5-2:7 Command: config vlan v1 delete 2:5-2:7 Success. DGS-3324SRi:4# config gvrp Purpose Syntax Description Parameters Used to configure GVRP on the Switch - D-Link 3324SRi | Reference Manual - Page 134
to enable and disable GVRP globally on the Switch, without changing the GVRP configuration on the Switch. None. Only administrator-level users can issue this command. Example usage: To enable the generic VLAN Registration Protocol (GVRP): DGS-3324SRi:4#enable gvrp Command: enable gvrp Success - D-Link 3324SRi | Reference Manual - Page 135
GVRP on the Switch, without changing the GVRP configuration on the Switch. None. Only administrator-level users can issue this command. Example usage: To disable the Generic VLAN Registration Protocol (GVRP): DGS-3324SRi:4#disable gvrp Command: disable gvrp Success. DGS-3324SRi:4# show vlan - D-Link 3324SRi | Reference Manual - Page 136
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show vlan Command: show vlan VID VLAN TYPE UserDefinedPid Encap Member ports Static ports Untagged ports Forbidden ports : 1 : 1QVLAN : : : 1:1-1:24,2:1-2:24 : 1:1-1:24,2:1-2:24 : 1:1-1:24,2:1-2:24 : VLAN Name : default Protocol ID - D-Link 3324SRi | Reference Manual - Page 137
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show gvrp Command: show gvrp Global GVRP : Disabled Port PVID GVRP Ingress Checking Acceptable Frame Type ------ ---- -------- 1:1 1 Disabled Enabled All Frames 1:2 1 Disabled Enabled All Frames 1:3 1 - D-Link 3324SRi | Reference Manual - Page 138
1-32> − Specifies the group ID. The Switch allows up to 32 link aggregation groups to be configured. The group number identifies each of the groups. type - Specify the type of link aggregation used for the group. If the type is not specified the default type is static. lacp - This designates the - D-Link 3324SRi | Reference Manual - Page 139
| disable] This command allows you to configure a link aggregation group that was created with the create link_aggregation command above. The DGS-3324SRi supports link aggregation cross box which specifies that link aggregation groups may be spread over multiple switches in the Switching stack. 131 - D-Link 3324SRi | Reference Manual - Page 140
Switch Command Line Interface Manual Parameters Restrictions group _id − Specifies the group ID. The Switch allows up to 32 link aggregation groups to be configured. DGS-3324SRi:4# config link_aggregation algorithm Purpose Syntax Description Parameters Used to configure the link - D-Link 3324SRi | Reference Manual - Page 141
examine the IP destination address. ip_source_dest − Indicates that the Switch should examine the IP source address and the destination address. Only administrator-level users can issue this command. Example usage: To configure link aggregation algorithm for mac-source-dest: DGS-3324SRi:4#config - D-Link 3324SRi | Reference Manual - Page 142
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show link_aggregation Command: show link_aggregation Link Aggregation Algorithm = MAC-source-dest Group ID : 1 Master Port : 2:17 Member Port : 1:5-1:10,2:17 Active Port: Status : Disabled Flooding Port : 1:5 DGS-3324SRi:4 config - D-Link 3324SRi | Reference Manual - Page 143
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#config lacp_port 1:1-1:12 mode active Command: config lacp_port 1:1-1:12 mode active Success. DGS-3324SRi:4# show lacp_port Purpose Syntax Description Parameters Restrictions Used to display current LACP port mode settings. - D-Link 3324SRi | Reference Manual - Page 144
. NOTE: Only the primary IP interface will support the BOOTP relay agent. IP Multinetting is a valuable tool for network administrators requiring a multitude of IP addresses, but configuring the Switch for IP multinetting may cause troubleshooting and bandwidth problems, and should not be used - D-Link 3324SRi | Reference Manual - Page 145
state enable Command: create ipif p1 ipaddress 12.1.1.1 Trinity secondary state enable Success. DGS-3324SRi:4# config ipif Purpose Syntax Used to configure an IP interface set on the Switch. config ipif [{ ipaddress | vlan | state [enable | disable - D-Link 3324SRi | Reference Manual - Page 146
the selection of the DHCP protocol for the assignment of an IP address to the Switch's System IP interface. Only administrator-level users can issue this command. Example usage: To configure the IP interface System: DGS-3324SRi:4#config ipif System ipaddress 10.48.74.122/8 Command: config ipif - D-Link 3324SRi | Reference Manual - Page 147
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#enable ipif s2 Command: enable ipif s2 Success. DGS-3324SRi:4# disable ipif Purpose Syntax Description Parameters Restrictions Used to disable the configuration of an IP interface on the Switch. disable ipif { - D-Link 3324SRi | Reference Manual - Page 148
Settings Interface Name : System Secondary : FALSE IP Address : 10.48.74.122 Subnet Mask : 255.0.0.0 VLAN Name : default Admin. State : Enabled Link Status : Link UP Member Ports : 1:1-1:24 (MANUAL) DGS-3324SRi:4# NOTE: In the IP Interface Settings table shown above, the Secondary - D-Link 3324SRi | Reference Manual - Page 149
Manual 18 IGMP COMMANDS (INCLUDING IGMP V3) IGMP or Internet Group Management Protocol is a protocol implemented by systems utilizing IPv4 to collect the membership information needed by the multicast routing protocol through various query messages sent out from the router or switch addresses. - D-Link 3324SRi | Reference Manual - Page 150
specific query messages. The default is 1 second. state [enable | disable] − Enables or disables IGMP for the specified IP interface. Only administrator-level users can issue this command. Example Usage: To configure the IGMPv3 for all IP interfaces. DGS-3324SRi:4#config igmp all version 3 state - D-Link 3324SRi | Reference Manual - Page 151
xStack Gigabit Layer 3 Switch Command Line Interface Manual show igmp Restrictions None. Example Usage: To display IGMP configurations: DGS-3324SRi:4#show igmp Command: show igmp IGMP Interface Configurations Interface IP Address/Netmask Ver- Query sion System 10.90.90.90/8 p1 20 - D-Link 3324SRi | Reference Manual - Page 152
Switch Command Line Interface Manual Total Entries: 5 DGS-3324SRi:4# Example usage: To view details regarding the IGMP group in version 3: DGS-3324SRi 233 DGS-3324SRi:4# Multicast Group : 224.0.1.1 IP Querier : 10.9.68.96 NOTE: To view the IGMP Group Detail Information in total, the user MUST - D-Link 3324SRi | Reference Manual - Page 153
Layer 3 Switch Command Line Interface Manual 19 IGMP SNOOPING configure IGMP snooping for all VLANs on the Switch. host_timeout − Specifies the maximum amount of time a host can be a member of a multicast group without the Switch receiving a host membership report. The default - D-Link 3324SRi | Reference Manual - Page 154
on the Switch. Configuring this function when IGMP is enabled will produce the error message "Cannot set Fast leave when IGMP is running" and consequently will not be implemented. Example usage: To configure igmp snooping including fast leave.: DGS-3324SRi:4#config igmp_snooping default host_timeout - D-Link 3324SRi | Reference Manual - Page 155
that must pass before a multicast router decides there are no more Switch to be specified as an IGMP Querier or Non-querier. Restrictions Only administrator-level users can issue this command. Example usage: To configure the igmp snooping: DGS-3324SRi:4#config igmp_snooping querier default - D-Link 3324SRi | Reference Manual - Page 156
multicast traffic to a multicast-enabled router. Otherwise, the Switch will forward all multicast traffic to any IP router. Only administrator-level users can issue this command. Example usage: To enable IGMP snooping on the Switch: DGS-3324SRi:4#enable igmp_snooping Command: enable igmp_snooping - D-Link 3324SRi | Reference Manual - Page 157
users can issue this command. Example usage: To set up static router ports: DGS-3324SRi:4#config router_ports default add 2:1-2:10 Command: config router_ports default add 2:1-2:10 Success. DGS-3324SRi:4# config router_ports_forbidden Purpose Syntax Description Parameters Used to configure - D-Link 3324SRi | Reference Manual - Page 158
: DGS-3324SRi:4#config router_ports_forbidden default add 2:1-2:10 Command: config router_ports_forbidden default add 2:1-2:10 Success. DGS-3324SRi:4# show router_ports Purpose Syntax Description Parameters Restrictions Used to display the currently configured router ports on the Switch. show - D-Link 3324SRi | Reference Manual - Page 159
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show router_ports Command: show router_ports VLAN Name : default Static router port : 2:1-2:10 Dynamic router port : Forbidden Router Port: VLAN Name : vlan2 Static router port : Dynamic router port : Forbidden Router Port: Total - D-Link 3324SRi | Reference Manual - Page 160
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show igmp_snooping Command: show igmp_snooping IGMP Snooping Global State : Disabled Multicast router Only : Disabled VLAN Name Query Interval Max Response Time Robustness Value Last Member Query Interval Host Timeout - D-Link 3324SRi | Reference Manual - Page 161
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show igmp_snooping group Command: show igmp_snooping group VLAN Name : default Multicast group: 224.0.0.2 MAC address : 01-00-5E-00-00-02 Reports : 1 Port Member : 1:26,2:7 VLAN Name : default Multicast group: 224 - D-Link 3324SRi | Reference Manual - Page 162
forwarding table entries currently configured on the Switch. − The name of the VLAN for which to view IGMP snooping forwarding table information. None. Example usage: To view the IGMP snooping forwarding table for VLAN "Trinity": DGS-3324SRi:4#show igmp_snooping forwarding vlan - D-Link 3324SRi | Reference Manual - Page 163
on the Switch. enable mac_notification This command is used to enable MAC Address Notification without changing configuration. None. Only administrator-level users can issue this command. Example Usage: To enable MAC notification without changing basic configuration: DGS-3324SRi:4#enable - D-Link 3324SRi | Reference Manual - Page 164
in the history log used for notification. Only administrator-level users can issue this command. Example usage: To configure the Switch's MAC address table notification global settings: DGS-3324SRi:4#config mac_notification interval 1 historysize 500 Command: config mac_notification interval - D-Link 3324SRi | Reference Manual - Page 165
] - These commands will enable or disable MAC address table notification on the Switch. Only administrator-level users can issue this command. Example usage: To enable port 7 for MAC address table notification: DGS-3324SRi:4#config mac_notification ports 1:7 enable Command: config mac_notification - D-Link 3324SRi | Reference Manual - Page 166
Manual DGS-3324SRi:4#show mac_notification Command: show mac_notification Global Mac Notification Settings State : Enabled Interval : 1 History Size : 1 DGS-3324SRi:4# show mac_notification ports Purpose Syntax Description Parameters Restrictions Used to display the Switch's MAC address - D-Link 3324SRi | Reference Manual - Page 167
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show mac_notification ports Command: show mac_notification ports Port # MAC Address Table Notification State 1:1 1:2 1:3 1:4 1:5 1:6 1:7 1:8 1:9 1:10 1:11 1:12 1:13 1:14 1:15 1:16 1:17 1:18 1:19 1:20 Disabled Disabled - D-Link 3324SRi | Reference Manual - Page 168
for authentication and can be responsible for receiving user connection requests, authenticating the user and returning all configuration information necessary for the client to deliver service through the user. RADIUS may be facilitated on this Switch using the commands listed in this section. In - D-Link 3324SRi | Reference Manual - Page 169
xStack Gigabit Layer 3 Switch Command Line Interface Manual NOTE: TACACS, XTACACS and TACACS+ are separate entities and are not compatible. The switch and the server must be configured exactly the same, using the same protocol. (For example, if the Switch is set up for TACACS authentication, so must - D-Link 3324SRi | Reference Manual - Page 170
for users trying to access the Switch. When enabled, the device will check the method list and choose a technique for user authentication upon login. None. Only administrator-level users can issue this command. Example usage: To enable the system access authentication policy: DGS-3324SRi:4#enable - D-Link 3324SRi | Reference Manual - Page 171
command is used to create a list for authentication techniques for user login. The Switch can support up to eight method lists, but one is reserved as a default and cannot be deleted. Multiple method lists must be created and configured separately. - Enter an alphanumeric string of up to - D-Link 3324SRi | Reference Manual - Page 172
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#create authen_login method_list_name Trinity Command: create authen_login method_list_name Trinity Success. DGS-3324SRi:4# config authen_login Purpose Syntax Description Parameters Used to configure a user-defined or default method list - D-Link 3324SRi | Reference Manual - Page 173
list or on the default method list. Restrictions Only administrator-level users can issue this command. Example usage: To configure the user defined method list "Trinity" with authentication methods TACACS, XTACACS and local, in that order. DGS-3324SRi:4#config authen_login method_list_name - D-Link 3324SRi | Reference Manual - Page 174
xStack Gigabit Layer 3 Switch Command Line Interface Manual To configure the default method list with authentication methods XTACACS, TACACS+ and local, in that order: DGS-3324SRi:4#config authen_login default method xtacacs tacacs+ local Command: config authen_login default method xtacacs tacacs - D-Link 3324SRi | Reference Manual - Page 175
the Switch). default - Entering this parameter will display the default method list for users logging on to the Switch. login methods currently configured on the Switch. Only administrator-level users can issue this command. Example usage: To view all method list configurations: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 176
Success. DGS-3324SRi:4# config authen_enable Purpose Syntax Description Parameters Used to configure a user-defined method list of authentication methods for promoting normal user level privileges to Administrator level privileges on the Switch. config authen_enable [default | method_list_name - D-Link 3324SRi | Reference Manual - Page 177
parameter will require the user to be authenticated using a user-defined server group previously configured on the Switch. local_enable - Adding this parameter will require the user to be authenticated using the local user account database on the Switch. The local enable password of the device can - D-Link 3324SRi | Reference Manual - Page 178
Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#config authen_enable method_list_name Trinity method tacacs xtacacs local Command: config authen_enable method_list_name Trinity method tacacs xtacacs local Success. DGS-3324SRi:4# Example usage: To configure the default method list - D-Link 3324SRi | Reference Manual - Page 179
password on the Switch) and none (no authentication necessary to access any function on the Switch). default - Entering this parameter will display the default method list for users login methods currently configured on the Switch. None. Example usage: To display all method lists for promoting user - D-Link 3324SRi | Reference Manual - Page 180
Entries : 2 DGS-3324SRi:4# config authen application Purpose Syntax Description Parameters Used to configure various applications on the Switch for authentication using a previously configured method list. config authen application [console | telnet | ssh | http | all] [login | enable] [default - D-Link 3324SRi | Reference Manual - Page 181
Only administrator-level users can issue this command. Example usage: To configure the default method list for the web interface: DGS-3324SRi:4#config authen application http login default Command: config authen application http login default Success. DGS-3324SRi:4# show authen application - D-Link 3324SRi | Reference Manual - Page 182
entities and are not compatible with each other. The maximum supported number of server hosts is 16. Parameters server_host - The IP address of the remote server host to add. protocol - The protocol used by the server host. The user may choose one of the following: tacacs - Enter this - D-Link 3324SRi | Reference Manual - Page 183
authen server_host 10.1.1.121 protocol tacacs+ port 1234 timeout 10 retransmit 5 Success. DGS-3324SRi:4# config authen server_host Purpose Syntax Description Parameters Used to configure a user-defined authentication server host. config authen server_host protocol [tacacs | xtacacs - D-Link 3324SRi | Reference Manual - Page 184
the TACACS+ protocol. Restrictions Only administrator-level users can issue this command. Example usage: To configure a TACACS authentication server host, with port number 4321, a timeout value of 12 seconds and a retransmit count of 4. DGS-3324SRi:4#config authen server_host 10.1.1.121 protocol - D-Link 3324SRi | Reference Manual - Page 185
to be shared with a configured TACACS+ server only. None. Only administrator-level users can issue this command. Example usage: To view authentication server hosts currently set on the Switch: DGS-3324SRi:4#show authen server_host Command: show authen server_host IP Address Protocol Port Timeout - D-Link 3324SRi | Reference Manual - Page 186
Switch Command Line Interface Manual create authen server_group Purpose Syntax Description Parameters Restrictions Used to create a user-defined Only administrator-level users can issue this command. Example usage: To create the server group "group_1": DGS-3324SRi:4#create authen server_group - D-Link 3324SRi | Reference Manual - Page 187
a server host from a server group. server_host - Enter the IP address of the previously configured server host to add or delete. protocol - Enter the protocol utilized by DGS-3324SRi:4# delete authen server_group Purpose Syntax Description Parameters Restrictions Used to delete a user - D-Link 3324SRi | Reference Manual - Page 188
Switch Command Line Interface Manual To delete the server group "group_1": DGS-3324SRi:4#delete server_group group_1 Command: delete server_group group_1 Success. DGS-3324SRi currently configured on the Switch, including built in groups and user defined groups. IP Address: The IP address of the - D-Link 3324SRi | Reference Manual - Page 189
of 0 will denote that the Switch will never time out while waiting for a response of authentication. The default setting is 30 seconds. Only administrator-level users can issue this command. Example usage: To configure the response timeout for 60 seconds: DGS-3324SRi:4# config authen parameter - D-Link 3324SRi | Reference Manual - Page 190
3 Switch Command Line Interface Manual config authen parameter attempt before being locked out. The default setting is 3 attempts. Restrictions Only administrator-level users can issue this command. Example usage: To set the maximum number of authentication attempts at 5: DGS-3324SRi:4#config - D-Link 3324SRi | Reference Manual - Page 191
a password configured by the administrator that will support the "enable" function. This function becomes inoperable when the authentication policy is disabled. None. Only administrator-level users can issue this command. Example usage: To enable administrator privileges on the Switch: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 192
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#config admin local_enable Command: config admin local_enable Enter the old password: ****** Enter the case-sensitive new password:****** Enter the new password again for confirmation:****** Success. DGS-3324SRi:4# 184 - D-Link 3324SRi | Reference Manual - Page 193
This is identical to creating any other admin-lever User account on the Switch, including specifying a password. This password is used to login to the Switch, once secure communication has been established using the SSH protocol. Configure the user account to use a specified authorization method to - D-Link 3324SRi | Reference Manual - Page 194
-level users can issue this command. Usage Example: To disable SSH: DGS-3324SRi:4# disable ssh Command: disable ssh Success. DGS-3324SRi:4# config ssh authmode Purpose Syntax Description Used to configure the SSH authentication mode setting. config ssh authmode [password | publickey - D-Link 3324SRi | Reference Manual - Page 195
the current SSH authentication set on the Switch. None. None. Example usage: To view the current authentication mode set on the Switch: DGS-3324SRi:4#show ssh authmode Command: show ssh authmode The SSH User Authentication Support Password : Enabled Publickey : Enabled Hostbased : Enabled 187 - D-Link 3324SRi | Reference Manual - Page 196
to attempt another login. rekey [10min | 30min | 60min | never] - Sets the time period that the Switch will change the security shell encryptions. Restrictions Only administrator-level users can issue this command. Usage Example: To configure the SSH server: DGS-3324SRi:4# config ssh server - D-Link 3324SRi | Reference Manual - Page 197
be chosen if the user wishes to use the publickey on a SSH server for authentication. Only administrator-level users can issue this command. Example usage: To configure the SSH user: DGS-3324SRi:4# config ssh user Trinity authmode Password Command: config ssh user Trinity authmode Password 189 - D-Link 3324SRi | Reference Manual - Page 198
: UserName Trinity Authentication Publickey DGS-3324SRi:4# Note: To configure the SSH user, the administrator must create a user account on the Switch. For information concerning configuring a user account, please see the section of this manual entitled Basic Switch Commands and then the - D-Link 3324SRi | Reference Manual - Page 199
xStack Gigabit Layer 3 Switch Command Line Interface Manual config ssh algorithm Encryption Standard AES256 encryption algorithm. , on the Switch. Restrictions Only administrator-level users can issue this command. Usage Example: To configure SSH algorithm: DGS-3324SRi:4# config ssh algorithm - D-Link 3324SRi | Reference Manual - Page 200
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show ssh algorithm Command: show ssh algorithm Encryption Algorithm 3DES AES128 AES192 AES256 ARC4 Blowfish Cast128 Twofish128 Twofish192 Twofish256 :Enabled :Enabled :Enabled :Enabled :Enabled :Enabled : - D-Link 3324SRi | Reference Manual - Page 201
of the certificate file and can be downloaded to the Switch by utilizing a TFTP server. The xStack family of switches supports SSLv3 and TLSv1. Other versions of SSL may not be compatible with this Switch and may cause problems upon authentication and transfer of messages from client to host - D-Link 3324SRi | Reference Manual - Page 202
:enable ssl Note: Web will be disabled if SSL is enabled. Success. DGS-3324SRi:4# NOTE: Enabling SSL on the Switch will enable all ciphersuites, upon initial configuration. To utilize a particular ciphersuite, the user must eliminate other ciphersuites by using the disable ssl command along with - D-Link 3324SRi | Reference Manual - Page 203
xStack Gigabit Layer 3 Switch Command Line Interface Manual NOTE: Enabling the SSL function on the Switch will disable the port for the keys. Only administrator-level users can issue this command. Example usage: To disable the SSL status on the Switch: DGS-3324SRi:4#disable ssl Command: disable - D-Link 3324SRi | Reference Manual - Page 204
xStack Gigabit Layer 3 Switch Command Line Interface Manual To disable ciphersuite RSA_EXPORT_with_RC4_40_MD5 only: DGS-3324SRi:4#disable ssl ciphersuite RSA_EXPORT_with_RC4_40_MD5 Command: disable ssl ciphersuite RSA_EXPORT_with_RC4_40_MD5 Success. DGS-3324SRi:4# config ssl cachetimeout Purpose - D-Link 3324SRi | Reference Manual - Page 205
Example usage: xStack Gigabit Layer 3 Switch Command Line Interface Manual To view the SSL cache timeout on the Switch: DGS-3324SRi:4#show ssl cachetimeout Command: show ssl cachetimeout Cache timeout is 600 second(s). DGS-3324SRi:4# show ssl Purpose Syntax Description Parameters Restrictions - D-Link 3324SRi | Reference Manual - Page 206
of the SSL function. The Switch only supports certificate files with .der file extensions. - Enter the IP address of the TFTP server. administrator-level users can issue this command. Example usage: To download a certificate file and key file to the Switch: DGS-3324SRi:4# download - D-Link 3324SRi | Reference Manual - Page 207
Switch Command Line Interface Manual 24 802.1X COMMANDS The xStack family of switches implement the server-side of the IEEE 802.1x Port-based and MAC-based Network Access Control. This mechanism is intended to allow only authorized users none] [ | all] [default | {direction [both | in] - D-Link 3324SRi | Reference Manual - Page 208
xStack Gigabit Layer 3 Switch Command Line Interface Manual Command statistics show auth_statistics Parameters {ports [ | level users can issue this command. Example usage: To enable 802.1x switch wide: DGS-3324SRi:4#enable 802.1x Command: enable 802.1x Success. DGS-3324SRi:4# - D-Link 3324SRi | Reference Manual - Page 209
control local users currently configured on the Switch. None. None. Example usage: To view 802.1X users currently configured on the Switch: DGS-3324SRi:4#show 802.1x user Command: show 802.1x user Current Accounts: Username Password Darren Trinity Total entries: 1 DGS-3324SRi:4# 201 - D-Link 3324SRi | Reference Manual - Page 210
Example Usage: To delete 802.1x users: DGS-3324SRi:4# delete 802.1x user dtremblett Command: delete 802.1x user dtremblett Success. DGS-3324SRi:4# show 802.1x auth_configuration Purpose Syntax Description Used to display the current configuration of the 802.1x server on the Switch. show 802.1x - D-Link 3324SRi | Reference Manual - Page 211
xStack Gigabit Layer 3 Switch Command Line Interface Manual show 802.1x auth_configuration and transmitting on the Switch. Restrictions Only administrator-level users can issue this command. Example usage: To display the 802.1x authentication states (stacking disabled): DGS-3324SRi:4#show 802 - D-Link 3324SRi | Reference Manual - Page 212
xStack Gigabit Layer 3 Switch Command Line Interface Manual SuppTimeout ServerTimeout MaxReq ReAuthPeriod ReAuthenticate : 30 sec − in numerical order. all - denotes all ports on the Switch Restrictions Only administrator-level users can issue this command. Example usage: To display the 802.1x - D-Link 3324SRi | Reference Manual - Page 213
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show 802.1x auth_state Command: show 802.1x auth_state auth state for MAC-based 802.1x: DGS-3324SRi:4#show 802.1x auth_state Command: show 802.1x auth_state Port number : 1:1 Index MAC Address 1 00-08-02-4E-DA-FA 2 - D-Link 3324SRi | Reference Manual - Page 214
feature on the Switch. Parameters [port_based | mac_based ports] − The Switch may authenticate 802.1x by either port or MAC address. Restrictions Only administrator-level users can issue this command. Example usage: To configure 802.1x authentication by MAC address: DGS-3324SRi:4#config 802.1x - D-Link 3324SRi | Reference Manual - Page 215
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#config 802.1x capability ports 1:1 - 1:10 authenticator Command: config 802.1x capability ports 1:1 - 1:10 authenticator Success. DGS-3324SRi:4# config 802.1x auth_parameter Purpose Syntax Description Parameters Used to configure the 802 - D-Link 3324SRi | Reference Manual - Page 216
in the Re-authentication Period field, above. Restrictions Only administrator-level users can issue this command. Example usage: To configure 802.1x authentication parameters for ports 1 - 20 of switch 1: DGS-3324SRi:4#config 802.1x auth_parameter ports 1:1 - 1:20 direction both Command: config - D-Link 3324SRi | Reference Manual - Page 217
Switch Command Line Interface Manual DGS-3324SRi:4# config 802.1x auth_protocol local Command: config 802.1x auth_protocol local Success. DGS-3324SRi ports or for specified MAC addresses operating from a specified range of ports. port_based - This instructs the Switch to initialize 802.1x functions - D-Link 3324SRi | Reference Manual - Page 218
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4# config 802.1x init port_based ports all Command: config 802.1x init port_based ports all Success. DGS-3324SRi:4# config 802.1x reauth ports Purpose Syntax Description Parameters Restrictions Used to configure the 802.1x re - D-Link 3324SRi | Reference Manual - Page 219
The UDP port number for accounting requests. The default is 1813. Only administrator-level users can issue this command. Example usage: To configure the RADIUS server communication settings: DGS-3324SRi:4#config radius add 1 10.48.74.121 key dlink default Command: config radius add 1 10.48.74.121 - D-Link 3324SRi | Reference Manual - Page 220
used to configure the Switch's RADIUS settings. − Assigns a number to the current set of RADIUS server settings. Up to 3 groups of RADIUS server settings can be entered on the Switch. ipaddress − The IP address of the RADIUS server. key − Specifies that a password and - D-Link 3324SRi | Reference Manual - Page 221
xStack Gigabit Layer 3 Switch Command Line Interface Manual To configure the RADIUS settings: DGS-3324SRi:4#config radius 1 10.48.74.121 key dlink default Command: config radius 1 10.48.74.121 key dlink default Success. DGS-3324SRi:4# show radius Purpose Syntax Description Parameters Restrictions - D-Link 3324SRi | Reference Manual - Page 222
currently configured on the Switch. None. None. Example usage: To view the current RADIUS authentication client: DGS-3324SRi:4#show auth_client Command: show auth_client radiusAuthClient radiusAuthClientInvalidServerAddresses 0 radiusAuthClientIdentifier D-Link radiusAuthServerEntry - D-Link 3324SRi | Reference Manual - Page 223
Layer 3 Switch Command Line Interface Manual radiusAuthClientServerPortNumber between switch 1, port 3 and switch 2, port 4 − in numerical order. all - Specifies that all ports will be viewed. None. Example usage: To display the current authentication diagnostics for port 16: DGS-3324SRi:4#show - D-Link 3324SRi | Reference Manual - Page 224
Layer 3 Switch Command Line Interface Manual BackendResponses 0 switch 1, port 3 and switch 2, port 4 − in numerical order. all - Specifies that all ports will be viewed. None. Example usage: To display the current authentication session statistics for port 16: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 225
Gigabit Layer 3 Switch Command Line Interface Manual show auth_statistics Purpose switch 1, port 3 and switch 2, port 4 − in numerical order. all - Specifies that all ports will be viewed. None. Example usage: To display the current authentication statistics for port 16 of module 1: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 226
Switch Command Line Interface Manual 25 ACCESS CONTROL LIST (ACL) COMMANDS The xStack family of switches implement Access Control Lists that enable the Switch to deny network access to specific devices or device groups based on IP settings, MAC address xffff>} | protocol_id {user _mask - D-Link 3324SRi | Reference Manual - Page 227
this case, 1. The deny parameter instructs the Switch to filter any frames that meet the criteria − in this case, when a logical AND operation between an IP address specified in the next step and the ip_source_mask match. The default for an access profile on the Switch is to permit traffic flow. If - D-Link 3324SRi | Reference Manual - Page 228
xStack Gigabit Layer 3 Switch Command Line Interface Manual Command Parameters create access_profile ip {vlan | source_ip_mask | | dst_port_mask } | protocol_id {user _mask }]} profile_id } config access_profile profile_id - D-Link 3324SRi | Reference Manual - Page 229
802.1p profile_id 1 Command: create access_profile ethernet vlan 802.1p profile_id 1 Success. DGS-3324SRi:4# config access_profile profile_id (for Ethernet) Purpose Syntax Used to configure the Ethernet access profile on the Switch and to define specific values for the rules that will be used - D-Link 3324SRi | Reference Manual - Page 230
configured for the Ethernet access profile. ethernet - Specifies that the Switch MAC address. MAC address entries Switch that match this priority are forwarded to the CoS queue specified previously by the user. • {replace_priority} − Enter this parameter if you want to re-write the 802.1p default - D-Link 3324SRi | Reference Manual - Page 231
100 rules may be specified for the Ethernet access profile. Restrictions Only administrator-level users can issue this command. Example usage: To configure a rule for the Ethernet access profile: DGS-3324SRi:4#config access profile profile_id 1 add access_id 1 ethernet vlan Trinity 802.1p 1 port - D-Link 3324SRi | Reference Manual - Page 232
Switch Command Line Interface Manual create access_profile (IP) Restrictions • destination_ip_mask − Specifies an IP address mask for the destination IP address. • dscp − Specifies that the Switch -level users can issue this command. Example usage: To configure a rule for - D-Link 3324SRi | Reference Manual - Page 233
Interface Manual DGS-3324SRi:4#create access_profile ip protocol_id profile_id 2 Command: create access_profile ip protocol_id profile_id 2 Success. DGS-3324SRi:4# config access_profile profile_id (IP) Purpose Syntax Description Parameters Used to configure the IP access profile on the Switch and - D-Link 3324SRi | Reference Manual - Page 234
xStack Gigabit Layer 3 Switch Command Line Interface Manual config access_profile profile_id (IP) Control Message Protocol (ICMP) field within each packet. • type − Specifies that the access profile will apply to this ICMP type defined by a value - D-Link 3324SRi | Reference Manual - Page 235
100 rules may be specified for the IP access profile. Only administrator-level users can issue this command. Example usage: To configure a rule for the IP access profile: DGS-3324SRi:4#config access_profile profile_id 2 add access_id 2 ip protocol_id 2 port 1:2 deny Command: config access_profile - D-Link 3324SRi | Reference Manual - Page 236
Gigabit Layer 3 Switch Command Line Interface Manual create access_profile (packet to filter or forward it, based on the user's configuration. The user will specify which bytes to examine by entering them DGS-3324SRi:4# config access_profile profile_id (packet content mask) Purpose To configure - D-Link 3324SRi | Reference Manual - Page 237
Line Interface Manual config access_profile profile_id (packet content mask) Syntax Description Parameters identified by the Switch. When the Switch recognizes a packet with the identical byte as the one configured, it will either forward or filter the packet, based on the users command entered - D-Link 3324SRi | Reference Manual - Page 238
0x11111111 0x11111111 0x11111111 offset_16-31 0x11111111 0x11111111 0x11111111 0x11111111 port 1:1 deny Success. DGS-3324SRi:4# create access_profile (ipv6) Purpose Syntax Description Used to create an access profile on the Switch by examining the IPv6 part of the packet header. Masks can be - D-Link 3324SRi | Reference Manual - Page 239
this parameter will instruct the Switch to examine the flow label field of the IPv6 header. This flow label field is used by a source to label sequences of packets such as non-default quality of service or real time service packets. • source_ipv6_mask - Specifies an IP address mask for - D-Link 3324SRi | Reference Manual - Page 240
of packets such as non-default quality of service or real time service packets. This field is to be defined by the user in hex form. • source_ipv6 - Specifies an IP address mask for the source IPv6 address. • destination_ipv6 - Specifies an IP address mask for the destination - D-Link 3324SRi | Reference Manual - Page 241
Example usage: xStack Gigabit Layer 3 Switch Command Line Interface Manual To configure a previously created access profile based on IPv6 classification: DGS-3324SRi:4#config access_profile profile_id 4 add access_id 1 ipv6 class 1 flowlabel 0xABCD port 1:4 deny Command: config access_profile - D-Link 3324SRi | Reference Manual - Page 242
to display all access profile entries. Only administrator-level users can issue this command. Example usage: To display all of the currently configured access profiles on the Switch: DGS-3324SRi:4#show access_profile Command: show access_profile Access Profile Table Access Profile ID: 1 TYPE - D-Link 3324SRi | Reference Manual - Page 243
xStack Gigabit Layer 3 Switch Command Line Interface Manual 1 ABCD Total Entries: 4 DGS-3324SRi:4# 235 - D-Link 3324SRi | Reference Manual - Page 244
Gigabit Layer 3 Switch Command Line Interface Manual 26 TRAFFIC SEGMENTATION switch previously specified for traffic segmentation (i.e. following the specified above for config traffic_segmentation). Only administrator-level users can issue this command. Example usage: To configure - D-Link 3324SRi | Reference Manual - Page 245
lists for segmentation and the forward list must be on the same switch. Example usage: To display the current traffic segmentation configuration on the Switch. DGS-3324SRi:4#show traffic_segmentation Command: show traffic_segmentation Traffic Segmentation Table Port Forward Portlist 1:1 1:11 - D-Link 3324SRi | Reference Manual - Page 246
xStack Gigabit Layer 3 Switch Command Line Interface Manual 1:16 1:1-1:24,2:1-2:24 1:17 1:1-1:24,2:1-2:24 1:18 1:1-1:24,2:1-2:24 CTRL+C ESC q Quit SPACE n Next Page Enter Next Entry a All 238 - D-Link 3324SRi | Reference Manual - Page 247
the Switch being configured. Range is 1-12. priority - Assigns a priority value to the box, with lower numbers having higher priority. Range is 1-16. Restrictions Only administrator-level users can issue this command. Usage Example: To configure box priority: DGS-3324SRi:4#config - D-Link 3324SRi | Reference Manual - Page 248
will pre-assign the box type of switches in a stack. Parameters current_box_id - Identifies the Switch being configured. Range is 1-12. type - Enter the type of switch to be configured. The user may choose between the following: • DGS-3324SR - Name of a xStack switch that can be set in the stack - D-Link 3324SRi | Reference Manual - Page 249
Usage Example: xStack Gigabit Layer 3 Switch Command Line Interface Manual To configure box type: DGS-3324SRi:4#config box_type current_box_id 3 type BOX_NOTEXIST Command: config box_type current_box_id 3 type BOX_NOTEXIST Success. DGS-3324SRi:4# config all_boxes_id Purpose Syntax Description - D-Link 3324SRi | Reference Manual - Page 250
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show stack_information Command: show stack_information Box User Prio- Prom ID Set Type Exist rity version --- ---- ----------- 1 AUTO DGS-3324SRi exist 16 2.00-B01 2 - USR-NOT-CFG no 3 - USR-NOT-CFG no 4 - USR - D-Link 3324SRi | Reference Manual - Page 251
xStack Gigabit Layer 3 Switch Command Line Interface Manual 28 D-LINK SINGLE IP MANAGEMENT COMMANDS Simply put, D-Link Single IP Management is a concept that will stack switches together over Ethernet instead of using stacking ports or modules. Switches using Single IP Management (labeled here as - D-Link 3324SRi | Reference Manual - Page 252
of a SIM group, additional switches may join the group by manually configuring the Switch to be a MS. The CS will then serve as the in band entry point for access to the MS. The CS's IP address will become the path to all MS's of the group and the CS's Administrator's password, and/or authentication - D-Link 3324SRi | Reference Manual - Page 253
xStack Gigabit Layer 3 Switch Command Line Interface Manual enable sim Parameters Restrictions enabled. None. Only administrator-level users can issue this command. Example usage: To enable SIM on the Switch: DGS-3324SRi:4#enable sim Command: enable sim Success. DGS-3324SRi:4# disable sim - D-Link 3324SRi | Reference Manual - Page 254
Line Interface Manual show sim Parameters Restrictions Firmware Version - Displays the current Firmware version on the Switch. Device Name - Displays the user-defined device name on the Switch. MAC Address - Displays the MAC Address of the Switch. Capabilities - Displays the type of switch, be it - D-Link 3324SRi | Reference Manual - Page 255
sim candidates ID MAC Address 1 00-01-02-03-04-00 2 00-55-55-00-55-00 Platform / Capability DGS-3324SR L3 Switch DGS-3324SR L3 Switch Hold Time ----40 140 Firmware Version --------4.00-B13 4.00-B13 Device Name The Man default master Total Entries: 2 DGS-3324SRi:4# To show the member - D-Link 3324SRi | Reference Manual - Page 256
Command Line Interface Manual To show other groups information in summary, if group is specified: DGS-3324SRi:4#show sim group Command: show sim group SIM Group Name : default ID MAC Address 1 00-01-02-03-04-00 Platform / Capability DGS-3324SR L3 Switch Hold Time ----40 Firmware Device Name - D-Link 3324SRi | Reference Manual - Page 257
ID number and a password (if necessary). delete - Use this parameter to delete a member switch of a SIM group. The member switch should be defined by it ID number. Only administrator-level users can issue this command. Example usage: To add a member: DGS-3324SRi:4#config sim_group - D-Link 3324SRi | Reference Manual - Page 258
Layer 3 Switch Command Line Interface Manual Success. To delete a member: DGS-3324SRi:4# DGS-3324SRi:4#config sim_group delete 1 Command: config sim_group delete 1 Please wait for ACK... Success. DGS-3324SRi:4# config sim Purpose Syntax Description Parameters Used to configure role parameters - D-Link 3324SRi | Reference Manual - Page 259
3 Switch Command Line Interface Manual config sim Restrictions Only administrator-level users can issue this command. To change the time interval of the discovery protocol: DGS-3324SRi:4#config sim commander dp_interval 30 Command:config sim commander dp_interval 30 Success. DGS-3324SRi:4# To - D-Link 3324SRi | Reference Manual - Page 260
parameter to specify all members of the SIM group will receive the firmware or switch configuration. Only administrator-level users can issue this command. Example usage: To download firmware: DGS-3324SRi:4# download sim_ms firmware 10.53.13.94 c:/dgssri.had members all Command: download sim_ms - D-Link 3324SRi | Reference Manual - Page 261
Interface Manual To download configuration files: DGS-3324SRi:4#download sim_ms configuration 10.53.13.94 c:/dgssri.txt members all Command: download sim_ms configuration 10.53.13.94 c:/dgssri.txt members all This device is updating configuration. Please wait... Download Status : ID MAC Address - D-Link 3324SRi | Reference Manual - Page 262
xStack Gigabit Layer 3 Switch Command Line Interface Manual 29 TIME AND SNTP configure SNTP service from a NTP server. SNTP must be enabled for this command to function (See enable sntp). primary − This is the primary server the SNTP information will be taken from. − The IP address - D-Link 3324SRi | Reference Manual - Page 263
DGS-3324SRi:4# enable sntp Purpose Syntax Description Parameters Restrictions Enables SNTP server support. enable sntp This will enable SNTP support. SNTP service must be separately configured (see config sntp). Enabling and configuring SNTP support will override any manually configured system - D-Link 3324SRi | Reference Manual - Page 264
Interface Manual To enable the SNTP function: DGS-3324SRi:4#enable sntp Command: enable sntp Success. DGS-3324SRi:4# disable sntp Purpose Syntax Description Parameters Restrictions Disables SNTP server support. disable sntp This will disable SNTP support. SNTP service must be separately configured - D-Link 3324SRi | Reference Manual - Page 265
Switch Command Line Interface Manual To manually set system time and date settings: DGS-3324SRi:4#config time 30jun2003 16:30:30 Command: config time 30jun2003 16:30:30 Success. DGS-3324SRi -level users can issue this command. Example usage: To configure time zone settings: DGS-3324SRi:4#config - D-Link 3324SRi | Reference Manual - Page 266
clock to comply with any DST requirement. DST adjustment effects system time for both manually configured time and time set using SNTP service. disable - Disable the DST seasonal time adjustment for the Switch. repeating - Using repeating mode will enable DST seasonal time adjustment. Repeating mode - D-Link 3324SRi | Reference Manual - Page 267
the summertime. The possible offset times are 30, 60, 90, 120. The default value is 60. Only administrator-level users can issue this command. Example usage: To configure daylight savings time on the Switch: DGS-3324SRi:4#config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day - D-Link 3324SRi | Reference Manual - Page 268
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show time Command: show time Current Time Source : System Clock Boot Time : 2 Jul 2003 10:59:59 Current Time : 10 2nd Tue 15:00 To : Oct 2nd Wed 15:30 Annual From : 29 Apr 00:00 To : 12 Oct 00:00 DGS-3324SRi:4# 260 - D-Link 3324SRi | Reference Manual - Page 269
Gigabit Layer 3 Switch Command Line Interface Manual 30 ARP COMMANDS address corresponding to the IP address above. Only administrator-level users can issue this command. Example Usage: To create a static ARP entry for the IP address 10.48.74.121 and MAC address 00:50:BA:00:07:36: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 270
IP address 10.48.74.121 from the ARP table: DGS-3324SRi:4#delete arpentry 10.48.74.121 Command: delete arpentry 10.48.74.121 Success. DGS-3324SRi:4# config arp_aging time Purpose Syntax Description Parameters Restrictions Used to configure the age-out timer for ARP table entries on the Switch - D-Link 3324SRi | Reference Manual - Page 271
table entry was made, resides on. − The network address corresponding to the IP interface name above. static − Displays the static entries to the ARP table. None. Example Usage: To display the ARP table: DGS-3324SRi:4#show arpentry Command: show arpentry ARP Aging Time : 30 Interface - D-Link 3324SRi | Reference Manual - Page 272
Example Usage: xStack Gigabit Layer 3 Switch Command Line Interface Manual To remove dynamic entries in the ARP table: DGS-3324SRi:4#clear arptable Command: clear arptable Success. DGS-3324SRi:4# 264 - D-Link 3324SRi | Reference Manual - Page 273
will forward packets sent to this IP address. This will allow any Virtual Router IP address on the LAN to be used as the default first hop router by end hosts. Utilizing VRRP, the administrator can achieve a higher available default path cost without needing to configure every end host for dynamic - D-Link 3324SRi | Reference Manual - Page 274
Manual enable vrrp Restrictions Only administrator-level users can issue this command. Example Usage: To enable VRRP globally on the Switch: DGS-3324SRi:4#enable vrrp Command: enable vrrp Success. Example usage: DGS-3324SRi:4# To enable the virtual IP address to be pinged: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 275
Gigabit Layer 3 Switch Command Line Interface Manual To disable the virtual IP address from being pinged: DGS-3324SRi:4#disable vrrp ping Command: disable vrrp ping Success. DGS-3324SRi:4# create vrrp vrid Purpose Syntax Description Parameters To create a VRRP router on the Switch. vrid - D-Link 3324SRi | Reference Manual - Page 276
Interface Manual create vrrp vrid Master router. A false entry will disable the backup router from becoming the Master router. This setting must be consistent with all routers participating within the same VRRP group. The default setting is true. critical_ip - Enter the IP address of - D-Link 3324SRi | Reference Manual - Page 277
this router will become the backup router. VRRP routers that are assigned the same priority value will elect the highest physical IP address as the Master router. The default value is 100. (The value of 255 is reserved for the router that owns the IP address associated with the virtual router and - D-Link 3324SRi | Reference Manual - Page 278
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#config vrrp vrid 1 ipif Trinity state enable priority 100 advertisement_interval 2 config vrrp ipif Purpose Syntax Description Parameters Restrictions To configure the authentication type for the VRRP routers of an IP interface. config - D-Link 3324SRi | Reference Manual - Page 279
Switch (VRRP Enabled): DGS-3324SRi:4#show vrrp Command: show vrrp Global VRRP :Enabled Non-owner response PING : Disabled Interface Name Authentication type : System : No Authentication VRID : 2 Virtual IP Address : 10.53.13.3 Virtual MAC Address : 00-00-5E-00-01-02 Virtual Router State - D-Link 3324SRi | Reference Manual - Page 280
will delete all VRRP entries on the Switch. ipif - Enter the name of the IP interface which holds the VRRP router to delete. Only administrator-level users can issue this command. Example usage: To delete a VRRP entry: DGS-3324SRi:4#delete vrrp vrid 2 ipif Trinity Command: delete - D-Link 3324SRi | Reference Manual - Page 281
metric entry, representing the number of routers between the Switch and the IP address above. The default setting is 1. [primary | backup] - The user may choose between Primary and Backup. If the Primary Static/Default Route fails, the Backup Route will support the entry. Please take note that - D-Link 3324SRi | Reference Manual - Page 282
number of routers between the Switch and the IP address above. The default setting is 1. Only administrator-level users can issue this command. Example Usage: To add the default static address 10.48.74.121, with a metric setting of 1, to the routing table: DGS-3324SRi:4#create iproute default 10 - D-Link 3324SRi | Reference Manual - Page 283
will delete an existing default entry from the Switch's IP routing table. - The gateway IP address for the next hop router. Only administrator-level users can issue this command. Example usage: To delete the default IP route 10.53.13.254: DGS-3324SRi:4#delete iproute default 10.53.13.254 - D-Link 3324SRi | Reference Manual - Page 284
: To display the contents of the IP routing table: DGS-3324SRi:4#show iproute Command: show iproute Routing Table IP Address/Netmask Gateway 0.0.0.0 10.1.1.254 10.0.0.0/8 10.48.74.122 Interface System System Cost Protocol 1 Default 1 Local Total Entries: 2 DGS-3324SRi:4# 276 - D-Link 3324SRi | Reference Manual - Page 285
Switch Command Line Interface Manual 33 routing information between the OSPF and RIP routing protocols to all routers on the network that are running OSPF or RIP. Routing Count in the RIP routing protocol. Only administrator-level users can issue this command. Routing information source − RIP. - D-Link 3324SRi | Reference Manual - Page 286
: create route redistribute dst ospf src rip Success. DGS-3324SRi:4# create route redistribute dst rip src Purpose Syntax Description Parameters Used to add route redistribution settings for the exchange of OSPF routes to RIP routes on the Switch. create route redistribute dst rip src {all - D-Link 3324SRi | Reference Manual - Page 287
redistribute dst rip src ospf all metric 2 Success. DGS-3324SRi:4# config route redistribute dst ospf src Purpose Syntax Description Used configure route redistribution settings for the exchange of RIP routes to OSPF routes on the Switch. config route redistribute dst ospf src [static | rip - D-Link 3324SRi | Reference Manual - Page 288
the RIP routing protocol. Restrictions Only administrator-level users can issue this command. Routing information source − DGS-3324SRi:4# config route redistribute dst rip src Purpose Syntax Used configure route redistribution settings for the exchange of RIP routes to OSPF routes on the Switch - D-Link 3324SRi | Reference Manual - Page 289
Switch Command Line Interface Manual config route redistribute dst rip src internal | external | type_1 | type_2 | inter+e1 | inter+e2]] {metric } Description Route redistribution allows routers users can issue this command. Example Usage: To configure route redistributions: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 290
src ospf Command: delete route redistribute dst rip src ospf Success. DGS-3324SRi:4# show route redistribute Purpose Syntax Description Parameters Restrictions Used to display the route redistribution on the Switch. show route redistribute {dst [rip | ospf] | src [rip | static | local | ospf - D-Link 3324SRi | Reference Manual - Page 291
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show route redistribute Command: show route redistribute Source Protocol -------STATIC LOCAL Destination Type Protocol RIP All OSPF Type-2 Metric -------1 20 Total Entries : 2 DGS-3324SRi:4# 283 - D-Link 3324SRi | Reference Manual - Page 292
xStack Gigabit Layer 3 Switch Command Line Interface Manual 34 BOOTP RELAY COMMANDS The BOOTP relay is exceeded, the Switch will relay the BOOTP packet. Only administrator-level users can issue this command. Example Usage: To configure bootp relay status. DGS-3324SRi:4#config bootp_relay hops 4 - D-Link 3324SRi | Reference Manual - Page 293
IP destination addresses in the Switch's BOOTP relay table. − The name of the IP interface that contains the IP address below. − The BOOTP server IP address. Only administrator-level users can issue this command. Example Usage: To delete a BOOTP relay: DGS-3324SRi:4#config - D-Link 3324SRi | Reference Manual - Page 294
the BOOTP relay function on the Switch. None. Only administrator-level users can issue this command. Example Usage: To enable the BOOTP relay function: DGS-3324SRi:4#enable bootp_relay Command: enable bootp_relay Success. DGS-3324SRi:4# disable bootp_relay Purpose Syntax Description Parameters - D-Link 3324SRi | Reference Manual - Page 295
configuration for the Switch, or if an IP interface name is specified, the BOOTP relay configuration for that IP interface. − The name of the IP interface for which to display the current BOOTP relay configuration. None. Example Usage: To display bootp relay status: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 296
relay function. − The domain name of the entry. − The IP address of the entry. Only administrator-level users can issue this command. Example Usage: To set IP address 10.43.21.12 of primary. DGS-3324SRi:4#config dnsr primary 10.43.21.12 Command: config dnsr primary 10.43 - D-Link 3324SRi | Reference Manual - Page 297
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#config dnsr add static dns1 10.43.21.12 Command: config dnsr add static dns1 10.43.21.12 Success. DGS-3324SRi:4# Example Usage: To delete an entry domain name dns1, IP address 10.43.21.12 from DNS static table. DGS-3324SRi:4#config dnsr - D-Link 3324SRi | Reference Manual - Page 298
Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#enable dnsr cache Command: enable dnsr cache Success. Example Usage: DGS-3324SRi:4# To enable static table lookup for DNS relay. DGS-3324SRi:4#enable dnsr static Command: enable dnsr static Success. DGS-3324SRi:4# disable dnsr - D-Link 3324SRi | Reference Manual - Page 299
Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#disable dnsr cache Command: disable dnsr cache Success. Example Usage: DGS-3324SRi:4# To disable static table lookup for DNS relay. DGS-3324SRi:4#disable dnsr static Command: disable dnsr static Success. DGS-3324SRi:4# show dnsr - D-Link 3324SRi | Reference Manual - Page 300
Layer 3 Switch Command Line Interface Manual 36 RIP configure RIP on the Switch. − The name of the IP interface. all - To configure all RIP receiving mode for all IP interfaces. authentication [enable | disable] − Enables or disables authentication for RIP on the Switch. • - D-Link 3324SRi | Reference Manual - Page 301
xStack Gigabit Layer 3 Switch Command Line Interface Manual config rip Restrictions reception of RIP packets. • disabled on the Switch. Only administrator-level users can issue this command. Example Usage: To change the RIP receive mode for the IP interface System: DGS-3324SRi:4#config rip ipif - D-Link 3324SRi | Reference Manual - Page 302
specified, the show rip command will display the global RIP configuration for the Switch. None. Example Usage: To display RIP configuration: DGS-3324SRi:4#show rip Command: show rip RIP Global State : Disabled RIP Interface Settings Interface IP Address System 10.41.44.33/8 TX Mode RX Mode - D-Link 3324SRi | Reference Manual - Page 303
state [enable | disable]} This command is used to configure DVMRP on the Switch. ipif − The name of the IP interface for which DVMRP is to be configured. all − Specifies that DVMRP is to be configured for all IP interfaces on the Switch. metric − Allows the assignment of - D-Link 3324SRi | Reference Manual - Page 304
Layer 3 Switch Command Line Interface Manual config dvmrp Restrictions state [enable | disable] − Allows DVMRP to be enabled or disabled. Only administrator-level users can issue this command. Example Usage: To configure DVMRP configurations of IP interface System: DGS-3324SRi:4#config dvmrp - D-Link 3324SRi | Reference Manual - Page 305
Example Usage: xStack Gigabit Layer 3 Switch Command Line Interface Manual To disable DVMRP: DGS-3324SRi:4#disable dvmrp Command: disable dvmrp Success. DGS-3324SRi:4# show dvmrp routing_table Purpose Syntax Description Parameters Restrictions Used to display the current DVMRP routing table. - D-Link 3324SRi | Reference Manual - Page 306
xStack Gigabit Layer 3 Switch Command Line Interface Manual show dvmrp neighbor Parameters Restrictions − The name of the IP interface for which to display the DVMRP neighbor table. ipaddress − The IP address and netmask of the destination. The address and mask - D-Link 3324SRi | Reference Manual - Page 307
table. − This parameter will allow the user to display DVMRP settings for a specific IP interface. None. Example Usage: To show DVMRP configurations: DGS-3324SRi:4#show dvmrp Command: show dvmrp DVMRP Global State : Disabled Interface IP Address System 10.90.90.90/8 Trinity 12 - D-Link 3324SRi | Reference Manual - Page 308
Switch Command Line Interface Manual by the router to automatically remove IP interface. The default is disabled. Note that PIM settings must also be enabled globally for the Switch with the enable pim described below for PIM to operate on any configured IP interfaces. Only administrator-level users - D-Link 3324SRi | Reference Manual - Page 309
will enable PIM for the Switch. PIM settings must first be configured for specific IP interfaces using the config pim command. None. Only administrator-level users can use this command. Usage Example: To enable PIM as previously configured on the Switch: DGS-3324SRi:4#enable pim Command: enable - D-Link 3324SRi | Reference Manual - Page 310
IP address and netmask information using the traditional format or the CIDR format. For example, 10.1.2.3/255.255.0.0 or 10.2.3.4/16. If no parameters are specified, all PIM neighbor router tables are displayed. None. Example usage: To display PIM settings as configured on the Switch: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 311
for all interfaces. None. Usage Example: To display PIM settings as configured on the Switch: DGS-3324SRi:4#show pim Command: show pim PIM Global State : Disabled PIM-DM Interface Table Hello Join/Prune Interface IP Address Interval Interval State System 10.90.90.90/8 35 60 Enabled - D-Link 3324SRi | Reference Manual - Page 312
Gigabit Layer 3 Switch Command Line Interface Manual 39 IP MULTICASTING COMMANDS The IP multicasting commands in the the current IP multicast forwarding cache: DGS-3324SRi:4#show ipmc cache Command: show ipmc cache Multicast Group 224.1.1.1 224.1.1.1 224.1.2.3 Source Address/Netmask Upstream - D-Link 3324SRi | Reference Manual - Page 313
that are related to the PIM protocol. None. Usage Example To display the current IP multicast interface table by DVMRP entry: DGS-3324SRi:4#show ipmc protocol dvmrp Command: show ipmc protocol dvmrp Interface Name IP Address Multicast Routing System 10.90.90.90 DVMRP Total Entries - D-Link 3324SRi | Reference Manual - Page 314
administrator-level users can issue this command. Usage Example To create an entry in the MD5 key table: DGS-3324SRi:4# create md5 key 1 dlink Command: create md5 key 1 dlink Success. DGS-3324SRi:4# config md5 key Purpose Syntax Description Parameters Used to enter configure the password for - D-Link 3324SRi | Reference Manual - Page 315
Gigabit Layer 3 Switch Command Line Interface Manual config md5 key Restrictions Only administrator-level users can issue this command. Usage Example To configure an MD5 Key password: DGS-3324SRi:4#config md5 key 1 taboo Command: config md5 key 1 taboo Success. DGS-3324SRi:4# delete md5 key - D-Link 3324SRi | Reference Manual - Page 316
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show md5 Command: show md5 MD5 Key Table Configurations Key-ID -----1 2 3 4 Key ---------dlink develop fireball intelligent Total Entries: 4 DGS-3324SRi:4# 308 - D-Link 3324SRi | Reference Manual - Page 317
Gigabit Layer 3 Switch Command Line Interface Manual 41 OSPF CONFIGURATION COMMANDS The OSPF configuration commands in the | dead_interval | authentication [none | simple | md5 ] | metric state [enable | disable - D-Link 3324SRi | Reference Manual - Page 318
config ospf router_id This command is used to configure the OSPF router ID. − The IP address of the OSPF router. Only administrator-level users can issue this command. Usage Example To configure the OSPF router ID: DGS-3324SRi:4#config ospf router_id 10.48.74.122 Command: config - D-Link 3324SRi | Reference Manual - Page 319
is used to enable and disable OSPF on the Switch. None. Only administrator-level users can issue this command. Usage Example To disable OSPF on the Switch: DGS-3324SRi:4#disable ospf Command: disable ospf Success. DGS-3324SRi:4# show ospf Purpose Syntax Description Parameters Restrictions Usage - D-Link 3324SRi | Reference Manual - Page 320
xStack Gigabit Layer 3 Switch Command Line Interface Manual To show OSPF state: DGS-3324SRi:4#show ospf Command: show ospf OSPF Router ID : 10.1.1.2 State : Enabled OSPF Interface Settings Interface -----------System ip2 ip3 IP Address Area ID 10.90.90.90/8 0.0.0.0 20.1.1.1/8 0.0.0.0 30 - D-Link 3324SRi | Reference Manual - Page 321
an OSPF area and configure its settings. − The OSPF area ID. The user may enter a 32-bit number in the form of an IP address (xxx.xxx.xxx. . The default setting is 0. Only administrator-level users can issue this command. Usage Example: To create an OSPF area: DGS-3324SRi:4#create ospf - D-Link 3324SRi | Reference Manual - Page 322
advertisements to be enabled or disabled. metric − The OSPF area stub default cost. Only administrator-level users can issue this command. Usage Example To configure an OSPF area's settings: DGS-3324SRi:4#config ospf area 10.48.74.122 type stub stub_summary enable metric 1 Command - D-Link 3324SRi | Reference Manual - Page 323
of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. metric − A metric between 1 and 65535, which will be advertised. Only administrator-level users can issue this command. Usage Example To configure the OSPF host route settings: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 324
xStack Gigabit Layer 3 Switch Command Line Interface Manual delete ospf host_route Parameters Restrictions − The IP address of the OSPF host. Only administrator-level users can issue this command. Usage Example To delete an OSPF host route: DGS-3324SRi:4#delete ospf host_route 10.48.74 - D-Link 3324SRi | Reference Manual - Page 325
Gigabit Layer 3 Switch Command Line Interface Manual show ospf host_route Parameters Restrictions − The IP address of the host. None. Usage Example: To display the current OSPF host route table: DGS-3324SRi:4#show ospf host_route Command: show ospf host_route Host Address 10.48.73 - D-Link 3324SRi | Reference Manual - Page 326
of an IP address that uniquely identifies the network that corresponds to the OSPF Area. lsdb_type summary − Specifies the type of address aggregation. Only administrator-level users can issue this command. Usage Example To configure the OSPF area aggregation settings: DGS-3324SRi:4#delete ospf - D-Link 3324SRi | Reference Manual - Page 327
− Specifies the type of address aggregation. advertise [enable | disable] − Allows for the advertisement trigger to be enabled or disabled. Only administrator-level users can issue this command. Usage Example To configure the OSPF area aggregation settings: DGS-3324SRi:4#config ospf aggregation 10 - D-Link 3324SRi | Reference Manual - Page 328
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show ospf aggregation Command: show ospf aggregation OSPF Area Aggregation Settings Area ID -----------10.1.1.1 10.1.1.1 Aggregated LSDB Network Address Type 10.0.0.0/8 Summary 20.2.0.0/16 Summary Advertise - D-Link 3324SRi | Reference Manual - Page 329
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#show ospf lsdb Command: show ospf lsdb Area ID ----------0.0.0.0 0.0.0.0 1.0.0.0 1.0.0.0 1.0.0.0 * LSDB Type RTRLink Summary RTRLink Summary Summary ASExtLink Advertising Link State Cost Router ID ID 50.48.75.73 50.48.75. - D-Link 3324SRi | Reference Manual - Page 330
Area ID -----------10.1.1.1 Router ID of IP Address of Virtual Neighbor Virtual Neighbor Virtual Neighbor State 10.2.3.4 10.48.74.111 Exchange Total Entries : 1 DGS-3324SRi:4# config ospf ipif Purpose Syntax Description Parameters Used to configure the OSPF interface settings - D-Link 3324SRi | Reference Manual - Page 331
none | simple | md5 ] | metric | state [enable | disable]} This command is used to configure all of the OSPF interfaces on the Switch, using a single group of parameters, at one time. area - A 32-bit number in the form of an IP address (xxx.xxx.xxx - D-Link 3324SRi | Reference Manual - Page 332
OSPF interface. The default metric is 1. state [enable | disable] - Used to enable or disable this function. Only administrator-level users can issue this command. Usage Example To configure all of the OSPF interfaces on the Switch with a single group of parameters: DGS-3324SRi:4#config ospf all - D-Link 3324SRi | Reference Manual - Page 333
Hello Interval: 10 Transmit Delay: 1 Authentication: None IP Address: 123.234.12.34/24 ((Link Up) Metric: 1 Administrative State: Enabled DR State: DR Backup DR Address: None Dead Interval: 40 Retransmit Time: 5 Total Entries: 1 DGS-3324SRi:4# show ospf all Purpose Syntax Description Parameters - D-Link 3324SRi | Reference Manual - Page 334
xStack Gigabit Layer 3 Switch Command Line Interface Manual Priority: 1 DR Address: 123.234.12.34 Hello Interval: 10 Transmit Delay: 1 Authentication: None DR State: DR Backup DR Address: None Dead Interval: 40 Retransmit Time: 5 Total Entries: 2 DGS-3324SRi:4# create ospf virtual_link Purpose - D-Link 3324SRi | Reference Manual - Page 335
[none | simple | md5 ]} This command is used to configure the OSPF virtual interface settings. − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. − The OSPF router ID for the - D-Link 3324SRi | Reference Manual - Page 336
of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the remote area's Area Border Router. The router ID of the neighbor router. Only administrator-level users can issue this command. Usage Example: To delete an OSPF virtual interface from the Switch: DGS-3324SRi:4#delete ospf virtual_link - D-Link 3324SRi | Reference Manual - Page 337
in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the remote area's Area Border Router. This is the router ID of the neighbor router. Restrictions None. Usage Example: To display the current OSPF virtual interface configuration: DGS-3324SRi:4#show ospf virtual_link Command - D-Link 3324SRi | Reference Manual - Page 338
compatible when used in conjunction with each other. This switch supports and may be configured for many routing protocols, as a stand alone switch or more importantly, in utilizing the stacking function and Single IP Management of the Switch. Therefore the ability to exchange route information and - D-Link 3324SRi | Reference Manual - Page 339
Layer 3 Switch Command Line Interface Manual config route preference Purpose Syntax Description Parameters Restrictions Used to configure the route administrator-level users can issue this command. Example usage: To configure the route preference value for RIP as 50: DGS-3324SRi:4#config route - D-Link 3324SRi | Reference Manual - Page 340
xStack Gigabit Layer 3 Switch Command Line Interface Manual show route preference Parameters Restrictions local - Enter . Example usage: To view the route preference values for all routes: DGS-3324SRi:4# show route preference Command: show route preference Route Preference Settings Route Type - D-Link 3324SRi | Reference Manual - Page 341
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4# show route preference rip Command: show route preference rip Route Preference Settings Route Type Preference ---------- ---------- RIP 100 DGS-3324SRi:4# 333 - D-Link 3324SRi | Reference Manual - Page 342
Line Interface Manual 43 JUMBO FRAME COMMANDS Certain switches can support jumbo frames (frames larger than the standard Ethernet frame size of 1518 bytes). To transmit frames of up to 9K (and 9004 bytes tagged), the user can increase the maximum transmission unit (MTU) size from the default of - D-Link 3324SRi | Reference Manual - Page 343
of the jumbo frame function on the Switch. show jumbo_frame This command will show the status of the jumbo frame function on the Switch. None. None. Usage Example: To show the jumbo frame status currently configured on the Switch: DGS-3324SRi:4#show jumbo_frame Command: show jumbo_frame Off - D-Link 3324SRi | Reference Manual - Page 344
xStack Gigabit Layer 3 Switch Command Line Interface Manual 44 FILE SYSTEM COMMANDS File System commands are used to configure files stored on a storage accessory located in the Switch, such as a CompactFlash card that can be used with the DGS-3324SRi only. These commands are based on DOS - D-Link 3324SRi | Reference Manual - Page 345
xStack Gigabit Layer 3 Switch Command Line Interface Manual Example usage: To view the storage media accessory information: DGS-3324SRi:4#show storage_media_info Command: show storage_media_info Drive Media_Type Size Label C: CF Card 30MB TEST FS_Type FAT16 DGS-3324SRi:4# cd Purpose Syntax - D-Link 3324SRi | Reference Manual - Page 346
the information of a specific path. Only administrator-level users can issue this command. Example usage: To view the directory files on the media storage accessory: DGS-3324SRi:4#dir Command: dir ABC ABC.CFG CINDY_~1.CFG DEF.TXT TEST TEST1 2003/06/20 18:57 2003/07/27 - D-Link 3324SRi | Reference Manual - Page 347
xStack Gigabit Layer 3 Switch Command Line Interface Manual erase Purpose Syntax Description Parameters Restrictions Used to delete users can issue this command. Example usage: To delete a file: DGS-3324SRi:4#erase c:/aaa.cfg Command: erase c:/aaa.cfg processing...100 % Done!! DGS-3324SRi:4# - D-Link 3324SRi | Reference Manual - Page 348
xStack Gigabit Layer 3 Switch Command Line Interface Manual DGS-3324SRi:4#format c: FAT16 fast Command: format c: FAT16 fast formatting...100 % Format media successfully!! DGS-3324SRi:4# To full format the storage media accessory: DGS-3324SRi:4#format c: FAT16 full DOG Command: format c: FAT16 full - D-Link 3324SRi | Reference Manual - Page 349
3 Switch Command Line Interface Manual mkdir Parameters Restrictions - Enter the path and name of the file to be created. This entry cannot exceed 64 characters in length. Only administrator-level users can issue this command. Example usage: To create a new directory: DGS-3324SRi - D-Link 3324SRi | Reference Manual - Page 350
xStack Gigabit Layer 3 Switch Command Line Interface Manual ren Restrictions to be renamed. This entry cannot exceed 64 characters in length. Only administrator-level users can issue this command. Example usage: To rename a file: DGS-3324SRi:4#ren c:/abc.txt c:/cba.txt Command: ren c:/abc.txt - D-Link 3324SRi | Reference Manual - Page 351
xStack Gigabit Layer 3 Switch Command Line Interface Manual rmdir Restrictions Only administrator-level users can issue this command. Example usage: To delete a diectory: DGS-3324SRi:4#rmdir c:/test Command: rmdir c:/test Done!! DGS-3324SRi:4# 343 - D-Link 3324SRi | Reference Manual - Page 352
xStack Gigabit Layer 3 Switch Command Line Interface Manual 45 COMMAND HISTORY LIST The command history list the command. None. Example usage To display all of the commands in the CLI: DGS-3324SRi:4#? .. ? clear clear arptable clear counters clear fdb clear log config 802.1p default_priority - D-Link 3324SRi | Reference Manual - Page 353
Layer 3 Switch Command Line Interface Manual config authen_application CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All To display the parameters for a specific command: DGS-3324SRi:4#? config vlan2 tag 3 create vlan vlan2 tag 2 show router_ports show router ports login DGS-3324SRi:4# 345 - D-Link 3324SRi | Reference Manual - Page 354
> − The number of previously executed commands maintained in the buffer. Up to 40 of the latest executed commands may be viewed. None. Example usage To configure the command history: DGS-3324SRi:4#config command_history 20 Command: config command_history 20 Success - D-Link 3324SRi | Reference Manual - Page 355
xStack Gigabit Layer 3 Switch Command Line Interface Manual A TECHNICAL SPECIFICATIONS Physical and Environmental AC input & DXS-3350SR - 441 mm x 430 mm x 44 mm (1U), 19 inch rack-mount width DGS-3324SR and DGS-3324SRi - 3.15kg DXS-3326GSR - 6.5kg DXS-3350SR - 6.41kg FCC Part 15 Class A / IECES - D-Link 3324SRi | Reference Manual - Page 356
3 Switch Command Line Interface Manual General Protocols: Data Transfer Rates: Control IEEE 802.3ad Link Aggregation -568 100-ohm screened twisted-pair (STP)(100m) DGS-3324SRi - 24 x 10/100/1000 Mbps NWay ports, 8 SFP Ports, 6 10-Gigabit Staking ports DGS-3324SR - 24 x 10/100/1000 Mbps NWay ports - D-Link 3324SRi | Reference Manual - Page 357
/ DGS-3324SR / DXS-3326GSR - 2 MB per device DXS-3350SR - 4 MB per device 16 K MAC addresses per device 3K IP addresses per device Full-wire speed for all connections. 148,810 pps per port (for 100Mbps) 1,488,100 pps per port (for 1000Mbps) Automatic update. Max age: 10 - 1000000 seconds. Default
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
 |
 |
xStack
High-density Layer 3 Intelligent Gigabit Switch
Command Line Interface Reference Manual
Release IV
First Edition (October 2004)
6XSTACKCLI01
RECYCLABLE