Chamberlain B4613T Installation Manual - English
Chamberlain B4613T Manual
 |
View all Chamberlain B4613T manuals
Add to My Manuals
Save this manual to your list of manuals |
Chamberlain B4613T manual content summary:
- Chamberlain B4613T | Installation Manual - English - Page 1
Easy step-by-step interactive 3D instructions for this product can be found in DOWNLOAD THE FREE APP Available on most iOS and Android Devices AFTER YOUR ASSEMBLY WITH BILT, DOWNLOAD THE myQ® APP Installation Manual Inside - Chamberlain B4613T | Installation Manual - English - Page 2
- Chamberlain B4613T | Installation Manual - English - Page 3
the camera icon including the points ( ). 2. Send it in by texting the photo to 71403 (US). • Please read this manual and the enclosed safety materials carefully! • Fasten the manual near the garage door after installation. • The door WILL NOT CLOSE unless the Protector System® is connected and - Chamberlain B4613T | Installation Manual - English - Page 4
Open the Door Manually 41 Maintenance 42 Troubleshooting 43 Warranty 45 Automatic Garage Door Opener Safety & Maintenance Guide 46 Repair Parts service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. - Chamberlain B4613T | Installation Manual - English - Page 5
door halfway up. Release the door. If balanced, it should stay in place, supported entirely by its springs. 3. Raise and lower the door to check for binding walls and other objects • Buy a Wi-Fi range extender Visit support.chamberlaingroup.com for more details. See myQ® App Control page 36 to - Chamberlain B4613T | Installation Manual - English - Page 6
see if you will need any of the following items: l (2) 2X4 Pieces of wood : May be used to fasten the header bracket to the structural supports. Also used to position the garage door opener during installation and for testing the safety reversing sensors - Chamberlain B4613T | Installation Manual - English - Page 7
the carton and packing material until the installation and adjustment is complete. Instructions for the accessories will be attached to the accessory and are not included in this manual. The images throughout this manual are for reference only and your product may look different. 1. Header bracket - Chamberlain B4613T | Installation Manual - English - Page 8
Preparation Hardware ASSEMBLY Bolt Bolt 1/4"-20x1-3/4" INSTALLATION Lag Screw 5/16"-9x1-5/8" (4) Self-Threading Screw 1/4"-14x5/8" (2) DOOR CONTROL Threaded Shaft with Spring Trolley Nut Master Link Lock Washer 3/8" Hex Screw #8x3/8" (3) (packed with the sprocket cover) Nut 3/8" Lock - Chamberlain B4613T | Installation Manual - English - Page 9
rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has a cut out "window" at , and rest the back end of the rail on top. For convenience, put a support under the front end of the rail. 4. As a temporary stop, insert a screwdriver - Chamberlain B4613T | Installation Manual - English - Page 10
shown. Tighten securely with a1/4"-20 lock nut. DO NOT overtighten. 2. Remove the bolts from the top of the motor unit. 3. Use the carton to support the front end of the rail. 4. Place the "U" bracket, flat side down onto the motor unit and align the bracket holes with the bolt holes - Chamberlain B4613T | Installation Manual - English - Page 11
Assembly STEP 3 Install the Idler Pulley 1. L ay the belt beside the rail, as shown. Grasp the end with the hooked trolley connector and pass approximately 12" (30 cm) of belt through the window. Keep the ribbed side toward the rail, and allow it to hang until Assembly Step 4. 2. R emove the tape - Chamberlain B4613T | Installation Manual - English - Page 12
Assembly STEP 4 Install the Belt 1. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley. 2. Hook the trolley connector into the retaining slot on the trolley as shown (Figure 1). 3. With the trolley against the screwdriver, dispense the remainder of - Chamberlain B4613T | Installation Manual - English - Page 13
Assembly STEP 5 Tighten the Belt 1. By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley. Do not use any tools. Remove the screwdriver. 2. Insert a flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley. - Chamberlain B4613T | Installation Manual - English - Page 14
with vehicles to avoid accidental release. 7. NEVER connect garage door opener to power source until instructed to do so. 8. NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms. 9. Install wall-mounted garage - Chamberlain B4613T | Installation Manual - English - Page 15
when required. Installation procedures vary according to garage door types. Follow the instructions which apply to your door. 1. Close the door and mark the ), use lag screws (not provided) to securely fasten the 2x4 to structural supports as shown here and on page 16. 3. Open your door to the - Chamberlain B4613T | Installation Manual - English - Page 16
wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided. OPTION B - CEILING INSTALLATION 1. Extend the - Chamberlain B4613T | Installation Manual - English - Page 17
way, you will need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. 2. Position the rail bracket against the opener. The trolley can remain disconnected until instructed. Clevis Pin Ring Fastener Connected Disconnected 2x4 2x4 One-piece - Chamberlain B4613T | Installation Manual - English - Page 18
the garage door opener MUST be connected to structural supports. The instructions illustrate one of the examples below. 1.On finished brackets with the hex bolts, lock washers, and nuts. 6. Remove the 2x4 and manually close the door. If the door hits the rail, raise the header bracket. EXAMPLES - Chamberlain B4613T | Installation Manual - English - Page 19
Installation STEP 6 Attach the Emergency Release Rope and Handle To prevent possible SERIOUS INJURY or DEATH from a falling garage door: l If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open - Chamberlain B4613T | Installation Manual - English - Page 20
long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit. NOTE: Many door reinforcement kits provide for - Chamberlain B4613T | Installation Manual - English - Page 21
on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.) Header Wall 2x4 Support Header Bracket (Finished Ceiling) Door Bracket Optional Placement of Door Bracket Vertical Centerline of Garage Door For a door with no exposed framing - Chamberlain B4613T | Installation Manual - English - Page 22
Installation STEP 8 Connect the Door Arm to the Trolley Installation will vary according to the garage door type. Follow the instructions which apply to your door. OPTION A - SECTIONAL DOORS IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. 1. Close - Chamberlain B4613T | Installation Manual - English - Page 23
Installation STEP 8 Connect the Door Arm to the Trolley (continued) OPTION B- ONE-PIECE DOORS IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. 1. Close the door. Disconnect the trolley by pulling the emergency release handle. 2. Fasten the straight door arm - Chamberlain B4613T | Installation Manual - English - Page 24
Installation STEP 9 Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: l Besure power is NOT connected BEFORE installing door control. l Connect door control ONLY to12 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage - Chamberlain B4613T | Installation Manual - English - Page 25
) Staple STEP 11 Attach the Warning Labels 1. Attach the entrapment warning label on the wall near the door control with tacks or staples. 2. Attach the manual release/safety reverse test label in a visible location on the inside of the garage door. 3 Wire channel RED WHITE 25 - Chamberlain B4613T | Installation Manual - English - Page 26
Nut (2) The safety reversing sensors are designed to clip onto the door track with the provided sensor brackets. If the door track will not support the sensor bracket a wall installation is recommended. The sensor beam should be NO HIGHER than 6" (15 cm) above the floor. DOOR TRACK INSTALLATION - Chamberlain B4613T | Installation Manual - English - Page 27
Installation STEP 12 Install the Protector System (continued) WALL OPTION Make sure the brackets on each side are clear of the door track and have the same amount of clearance so the sensors will align correctly. If additional clearance is needed, use extension brackets 041A5281-1 (not provided) or - Chamberlain B4613T | Installation Manual - English - Page 28
Installation STEP 13 Wire the Safety Reversing Sensors If your garage has pre-installed wiring for the safety reversing sensors, see OPTION B- PRE-WIRED INSTALLATION page 27. OPTION A- INSTALLATION WITH NO PRE-WIRING 1. Run the wire from both sensors to the garage door opener. Attach with - Chamberlain B4613T | Installation Manual - English - Page 29
Installation STEP 13 Wire the Safety Reversing Sensors (continued) OPTION B- PRE-WIRED INSTALLATION 1. Cut the sensor wires, making sure there is enough wire to reach the pre-installed wires from the wall. 2. Separate the sensor wires and strip insulation from each end. Choose two of the pre- - Chamberlain B4613T | Installation Manual - English - Page 30
Installation STEP 14 Connect Power To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: l Be sure power is NOT connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection. l Garage door installation and wiring MUST be - Chamberlain B4613T | Installation Manual - English - Page 31
garaged door opener has power, check the safety reversing sensors. If the sensors are aligned and wired correctly, both LEDs will glow steadily. SAFETY SENSOR TROUBLESHOOTING If either of the sensor LEDs are off, there is no power to the sensor: 1. Check that you have power to the garage door - Chamberlain B4613T | Installation Manual - English - Page 32
Adjustments Introduction Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. l Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. l - Chamberlain B4613T | Installation Manual - English - Page 33
Force Setup the door will automatically open and close. 2 - Automatic Force Set Up Once both the up and down positions have been manually set, the Safety Reversing Sensors will reconnect and become operational. Then, the opener will enter a force-sensing operation by automatically moving the - Chamberlain B4613T | Installation Manual - English - Page 34
Adjustments 3 - Test the Safety Reversal System Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month. • After ANY adjustments are made, the safety - Chamberlain B4613T | Installation Manual - English - Page 35
to persons: l Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance. l Use ONLY Chamberlain part # G4228 for replacement battery. in fire. Battery may explode. Check with local codes for disposal instructions. STEP 2 Test the Battery Depending on the power level, the - Chamberlain B4613T | Installation Manual - English - Page 36
mobile device has the latest software. 2. Download the latest version of the myQ® App. For more information on connecting your garage door opener, visit support.chamberlaingroup.com. NOTES: myQ® App control WILL NOT work if the garage door opener is operating on battery power. To erase the Wi-Fi - Chamberlain B4613T | Installation Manual - English - Page 37
® App, setup an account, and connect. See page 36. 2. Follow the instructions in the app to setup and use the camera. The camera powers up when the camera status table. For more information on using the camera, visit support.chamberlaingroup.com. NOTES: myQ® App control and camera WILL NOT work if - Chamberlain B4613T | Installation Manual - English - Page 38
if using devices or features providing unattended close. Unattended devices and features are to be used ONLY with sectional doors. 16.SAVE THESE INSTRUCTIONS. Using your Garage Door Opener The garage door opener can be activated through a wall-mounted door control, remote control, wireless keyless - Chamberlain B4613T | Installation Manual - English - Page 39
Operation Motion Detecting Control Panel Push Bar Motion Sensor Switch LEARN Button LOCK Button LIGHT Button Motion Sensor Command LED SYNCHRONIZE THE DOOR CONTROL: To synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take - Chamberlain B4613T | Installation Manual - English - Page 40
and Keyless Entry PRE-PROGRAMMED REMOTE CONTROL INCLUDED, NO NEED TO PROGRAM THE REMOTE. To add or reprogram a remote control, follow the instructions below. Older Chamberlain remote controls are NOT compatible. PROGRAM MOTION DETECTING CONTROL PANEL 1. Press the LEARN button on the door control to - Chamberlain B4613T | Installation Manual - English - Page 41
light will turn off, then flash red. You will need to set up your camera again after resetting it. Reset Button To Open the Door Manually To prevent possible SERIOUS INJURY or DEATH from a falling garage door: l If possible, use emergency release handle to disengage trolley ONLY when garage door - Chamberlain B4613T | Installation Manual - English - Page 42
Maintenance Maintenance Schedule EVERY MONTH l Manually operate door. If it is unbalanced or binding, call a trained door radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee - Chamberlain B4613T | Installation Manual - English - Page 43
Troubleshooting Diagnostic Chart Your garage door opener is programmed with self- as needed. Check wiring connections at travel module and at the logic board. Replace travel module if necessary. Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, - Chamberlain B4613T | Installation Manual - English - Page 44
sending sensor so the receiving sensor is not in direct sunlight. Wi-Fi® troubleshooting The garage door opener will NOT enter Wi-Fi® learn mode: l LEARN mode. If your black adjustment button is not solid green go to support.chamberlaingroup.com. My vehicle's Home link® is not programming to my - Chamberlain B4613T | Installation Manual - English - Page 45
and aligned. Visit us online at: support.chamberlaingroup.com CHAMBERLAIN®LIMITED WARRANTY The Chamberlain instructions when you call. Then send the product or component, pre-paid and insured, as directed to our service center for warranty repair. Please include a brief description of the problem - Chamberlain B4613T | Installation Manual - English - Page 46
opener to ensure they function in a safe and trouble-free manner. Be sure to read all Important Safety Information found in your garage door opener's manual as it provides more details and safety considerations than can be supplied with this guide. Garage Door Openers are Not Toys Discuss garage - Chamberlain B4613T | Installation Manual - English - Page 47
TENSION. ONLY QUALIFIED INDIVIDUALS SHOULD ADJUST THEM. Visually check the door and installation: • Starting with the door in the closed position, use the manual disconnect on the opener to disconnect the door. • Look for signs of wear or damage on hinges, rollers, springs, and door panels. • These - Chamberlain B4613T | Installation Manual - English - Page 48
sensors with 2-conductor wire 8 Straight door arm 9 White and red/white wire 10 3V CR2032 lithium battery Not shown Installation Manual 2 3 1 4 6 8 8 5 5 7 6 7 Part Number 041B0035B 041A5047-1 041A2828 041A5047-2 K029B0137 041-0155 041-0136 4178B0034B 041B4494-1 K010A0020 114-5822-000 9 10 48 - Chamberlain B4613T | Installation Manual - English - Page 49
Repair Parts Garage Door Opener Parts - Model B4603T Description 1 Sprocket and sprocket cover 2 End panel 3 Cover and light pod 4 Control door panel 5 Motor with travel module 6 Logic board end panel 7 Logic board 8 Travel Module 9 Transformer 10 Line cord 11 Terminal block Not shown Badge Wire - Chamberlain B4613T | Installation Manual - English - Page 50
Repair Parts Garage Door Opener Parts - Model B4613T Description 1 Sprocket and sprocket cover 2 End panel 3 Cover and light pod 4 Transformer 5 Control door panel 6 Motor with travel module 7 Logic board end panel 8 Logic board 9 Travel module 10 Line cord 11 Terminal block Not shown Badge Wire - Chamberlain B4613T | Installation Manual - English - Page 51
Repair Parts Garage Door Opener Parts - Model B4643T and B4655T Description 1 Sprocket and sprocket cover 2 End panel 3 Cover and light pod 4 Transformer 5 Control door panel 6 Motor with travel module 7 Logic board end panel 8 Logic board 9 Travel module 10 Line cord 11 Terminal block 12 Camera - Chamberlain B4613T | Installation Manual - English - Page 52
Repair Parts Garage Door Opener Parts - Models B6713T, B6753T, and B6755T Description 1 Sprocket and sprocket cover 2 End panel Model B6713T 3 Cover and light pod Model B6753T Cover and light pod 4 Transformer 5 Control door panel 6 Motor with travel module 7 Logic board end panel 8 Logic
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
 |
 |
Easy step-by-step
interactive 3D instructions
for this product can be found in
DOWNLOAD THE
FREE
APP
Available on most iOS and Android Devices
AFTER YOUR ASSEMBLY WITH BILT,
DOWNLOAD THE myQ® APP
Installation Manual Inside