BenQ TK850 RS232 Control Guide

BenQ TK850 Manual

Get BenQ TK850 PDF manuals and user guides View all BenQ TK850 manuals
Add to My Manuals
Save this manual to your list of manuals

BenQ TK850 manual content summary:

  • BenQ TK850 | RS232 Control Guide - Page 1
    TK850 Projector RS232 Command Control Installation Guide
  • BenQ TK850 | RS232 Control Guide - Page 2
    Table of Contents Introduction ...3 Wire arrangement...3 RS232 pin assignment ...3 Connections and communication settings 4 RS232 serial port with a crossover cable ...4 Settings ...4 RS232 via LAN...6 Settings ...6 RS232 via HDBaseT...6 Settings ...6 Command table...8 2
  • BenQ TK850 | RS232 Control Guide - Page 3
    describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands. Available functions and commands vary by model. Check the specifications and user manual of the purchased
  • BenQ TK850 | RS232 Control Guide - Page 4
    Choose one of the connections and set up properly before RS232 control. RS232 serial port with a crossover cable D-Sub 9 pin (male) on a projector PC or laptop Communication cable (crossover) D-Sub 9 pin (female) Settings On-screen images in this document are for reference only. The screens may
  • BenQ TK850 | RS232 Control Guide - Page 5
    setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Data length Parity check Stop bit Flow control Check the baud rate of the connected projector from its OSD menu. 8 bit None 1 bit None 5
  • BenQ TK850 | RS232 Control Guide - Page 6
    the same network. 2. Input 8000 in the TCP port # field. RS232 via HDBaseT HDBaseT compatible device D-Sub 9 pin RJ45 RJ45 port on a projector PC or laptop D-Sub 9 pin LAN cable Settings 1. Determine the COM Port name used for the RS232 communications in Device Manager. 2. Choose Serial
  • BenQ TK850 | RS232 Control Guide - Page 7
    3. Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Data length Parity check Stop bit Flow control Check the baud rate of the connected projector from its OSD menu. 8 bit None 1 bit None 7
  • BenQ TK850 | RS232 Control Guide - Page 8
    specification, input sources, settings, etc..  Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set.  Uppercase, lowercase, and a mixture of both types of characters are accepted for a command.  If a command format is illegal, it will echo Illegal
  • BenQ TK850 | RS232 Control Guide - Page 9
    Read Mute Status *mute=?# YES Write Volume + *vol=+# YES Write Volume - *vol=-# YES Volume level for Write *vol=value# YES customer Read Volume Status *vol=?# YES Write Mic.Volume + *micvol=+# NO Write Mic.Volume - *micvol=-#<
  • BenQ TK850 | RS232 Control Guide - Page 10
    Write Set Contrast value *con=value# YES Read Contrast value *con=?# YES Write Brightness + *bri=+# YES Write Brightness - *bri=-# YES Write Set Brightness value *bri=value# YES Read Brightness value *bri=?# YES Write Color + *
  • BenQ TK850 | RS232 Control Guide - Page 11
    Read Brilliant color status *BC=?# YES Projector Write *pp=FT# YES Position-Front Table Projector Write *pp=RE# YES Position-Rear Table Projector Write *pp=RC# YES Position-Rear Ceiling Projector Write *pp=FC# YES Position-Front Ceiling
  • BenQ TK850 | RS232 Control Guide - Page 12
    Baud Rate Quick auto search Read *QAS=?# NO status Projector Position Read *pp=?# YES Status Write Direct Power On-on *directpower=on# YES Write Direct Power On-off *directpower=off#<
  • BenQ TK850 | RS232 Control Guide - Page 13
    Write 4800 *baud=4800# NO Write 9600 *baud=9600# NO Write 14400 *baud=14400# NO Write 19200 *baud=19200# NO Write 38400 *baud=38400# NO Write 57600 *baud=57600# NO Write 115200 *baud=115200# NO Read Current Baud Rate *
  • BenQ TK850 | RS232 Control Guide - Page 14
    Write 3D Sync Off *3d=off# NO Write 3D Auto *3d=auto# YES Write 3D Sync Top Bottom *3d=tb# YES 3D Sync Frame Write *3d=fs# NO Sequential Write 3D Frame packing *3d=fp# YES Write 3D Side by side *3d=sbs# YES Write 3D inverter disable <
  • BenQ TK850 | RS232 Control Guide - Page 15
    Installation Write Broadcasting on *broadcasting=on# NO Write Broadcasting off *broadcasting=off# NO Read Broadcasting Status *broadcasting=? NO AMX Device Write *amxdd=on# NO Discovery-on AMX Device Write *amxdd=off# NO Discovery-off AMX
  • BenQ TK850 | RS232 Control Guide - Page 16
    Write Tint - *tint=-# YES Write Set Tint value *tint=value# YES Read Get Tint value *tint=?# YES Write Set BenQ gamma value *gamma=value# YES Read Gamma value status *gamma=?# YES Set HDR Brightness Write *hdrbri=value# YES value
  • BenQ TK850 | RS232 Control Guide - Page 17
    Write Set Blue Offset value *BOffset=value# YES Read Get Blue Offset value *BOffset=?# YES Write Primary Color *primcr=value# YES Read Primary Color Status *primcr=?# YES Write Hue + *hue=+# YES Write Hue - *hue=-# YES Write Set Hue
  • BenQ TK850 | RS232 Control Guide - Page 18
    18
  • BenQ TK850 | RS232 Control Guide - Page 19
    BenQ.com © 2019 BenQ Corporation All rights reserved. Rights of modification reserved. Version: 1.01-C 19
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
TK850
Projector RS232 Command Control
Installation Guide