Home » Beltronics Manuals » Radar Detectors & Jammers » Beltronics STiDRIVER » Manual Viewer

Beltronics STiDRIVER User Manual

Beltronics STiDRIVER - STi Driver Radar Detector Manual

UPC - 065789290158

View all Beltronics STiDRIVER manuals

Add to My Manuals
Save this manual to your list of manuals

Beltronics STiDRIVER manual content summary:

Beltronics STiDRIVER | User Manual - Page 1
MAGNESIUM CONSTRUCTION BELTRONICS 5442 West Chester Road West Chester OH 45069 USA USA 800-341-2288 www.beltronics.com ©2005 BELTRONICS Made in Canada Features, specifications and prices subject to change without notice. Model: STi DRIVER DIGITAL RADAR• LASER• SAFETY DETECTOR Owner's Manual
Beltronics STiDRIVER | User Manual - Page 2
a radar detector before, a review of the Quick Reference Guide on pages 4 and 5, and the Programming information on pages 12 and 13 will brieﬂy explain the new features. If this is your ﬁrst detector, please read the manual in detail to get the most out of your BELTRONICS STi DRIVER's outstanding
Beltronics STiDRIVER | User Manual - Page 3
̄ ̄ Remove card along perforations ̄ BELTRONICS STi DRIVER Quick Reference Card Press the RVW button to go from one category to the next DISPLAY PILOT (Power-on indication) ALERT LAMP VOICE POWER-ON SEQUENCE SIGNAL STRENGTH METER AUTOMUTE BRIGHTNESS BANDS * Factory Default Settings Disp STD Disp
Beltronics STiDRIVER | User Manual - Page 4
Guide To begin using your STi DRIVER, just follow these simple steps 1 Plug the small end of the power cord into the side jack of the detector, and plug the large end of the power cord into your vehicle's lighter socket. 2 Mount your STi DRIVER on the windshield using the supplied windshield mount
Beltronics STiDRIVER | User Manual - Page 5
areas that might obstruct the radar antenna or laser lens. 6 Windshield QuickMount The STi DRIVER's QuickMount windshield bracket is designed for unobtrusive and hassle-free mounting and removal. 1 Depress the adjustment button on the top of the STi DRIVER (by the word BELTRONICS) and slide the
Beltronics STiDRIVER | User Manual - Page 6
there are no trafﬁc radar guns using X-band in your area. you have a detector. Two versions are included: A coiled SmartPlug that plugs into your lighter socket, and a Direct-wire SmartPlug module that's wired into the electrical system, with an 8 foot straight cord to route to your STi DRIVER. 9
Beltronics STiDRIVER | User Manual - Page 7
meter. When STi detects radar, it displays the band (X, K, Ka), and a precise bar-graph of the signal strength. When the STi DRIVER detects a laser signal, the display will show "LASER." When it detects a POP signal, the display will show "POP." NOTE: If you are operating the STi DRIVER in the Dark
Beltronics STiDRIVER | User Manual - Page 8
. The STi DRIVER will display Complete, beep 4 times, and return to normal operation. 12 Overview of Programming Press the REVIEW button to turning the power on. The STi DRIVER's display will provide a "Reset" message, accompanied by an audible alert, acknowledging the reset. Turn bands "ON" or
Beltronics STiDRIVER | User Manual - Page 9
the distinct audio tone will be heard when a radar, Laser, or SWS message is detected. 14 Power-on Sequence PwrOnSTD (Standard) In this setting, each time you turn on the STi DRIVER, it will display "Bel STi," "LASER," "Ka-band," "K-band," "X-band," followed by a brief SWS alert. (factory default
Beltronics STiDRIVER | User Manual - Page 10
power is turned off. BrtDark In this setting, the display and backlit buttons will be totally dark. The supplied SmartPlug will provide the only visual indication that the Sti DRIVER is operational. Bands BandsDFT In this setting, the factory default settings for radar and laser Power Requirement
Beltronics STiDRIVER | User Manual - Page 11
examples will give you an introduction to understanding the STi DRIVER's warning system for radar, laser and safety alerts. Alert The STi DRIVER begins to sound slowly, then the rate of alert increases. The Signal Meter ramps accordingly. STi DRIVER emits short alerts for a few seconds and then
Beltronics STiDRIVER | User Manual - Page 12
to travel, the less energy it has for speed detection. Because intrusion alarms and motion sensors often operate on the same frequency as X-Band or K-band radar, your STi DRIVER will occasionally receive nonpolice radar signals. Since these transmitters are usually contained inside of a building
Beltronics STiDRIVER | User Manual - Page 13
DRIVER is a completely undetectable radar, laser and safety detector, driving techniques and reactions to alerts can still draw unwanted attention. Here are a few examples: 1. Hitting the brakes immediately when the STi DRIVER provides an alert can broadcast use of a detector. 2. Visible power cords
Beltronics STiDRIVER | User Manual - Page 14
One of the many Safety Radar messages (pages 22-23) Caution STi DRIVER has detected a Safety Radar Signal, but the signal isn't yet strong enough to decode the speciﬁc safety message (pages 22-23) Service STi DRIVER has failed the calibration test. Contact Beltronics for repair Required 25
Beltronics STiDRIVER | User Manual - Page 15
to us, or register online at our web address: www.beltronics.com. ̄ Service Service Procedure If your STi DRIVER ever needs service, please follow these simple steps: 1 Check the troubleshooting section of this manual. It may have a solution to your problem. 2 Call us at 1-800-341-2288. We may be
Beltronics STiDRIVER | User Manual - Page 16
WITHOUT REPRESENTATION OR WARRANTY. BELTRONICS SPECIFICALLY DISCLAIMS ANY REPRESENTATION OR BELTRONICS STi DRIVER: Standard Coiled Power Cord $14.00 Direct-wire Power Cord $10.00 Coiled SmartPlug $29.95 Direct-wire SmartPlug $29.95 Accessory Kit $19.95 Extra Windshield Mount $4.00 Carrying Case