Apple MB194G/A Replacement Guide

Apple MB194G/A - 8 GB Memory Manual

Get Apple MB194G/A - 8 GB Memory PDF manuals and user guides View all Apple MB194G/A manuals
Add to My Manuals
Save this manual to your list of manuals

Apple MB194G/A manual content summary:

  • Apple MB194G/A | Replacement Guide - Page 1
     Mac Pro Memory (FB-DIMM) Replacement Instructions Follow the instructions in this document carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: The Mac Pro computer has two memory riser cards with a total of 8 memory slots. On each
  • Apple MB194G/A | Replacement Guide - Page 2
    computers is not compatible with Mac Pro. Important: For proper operation of Mac Pro computers, Apple recommends using only Appleapproved Mac Pro FB-DIMMs. Refer to GSX for Apple FB-DIMMs service part numbers. Tools Required No tools are required for this procedure. Opening the Computer 1. Shut
  • Apple MB194G/A | Replacement Guide - Page 3
    5. Unplug the power cord. 6. Hold the side access panel and lift the latch on the back of the computer. Warning: The edges of the access panel and the enclosure can be sharp. Be very careful when handling them. 7. Remove the access panel and place it on a flat surface covered by a soft, clean cloth.
  • Apple MB194G/A | Replacement Guide - Page 4
    Removing the Installed FB-DIMM 1. Carefully lay the computer on its side so that the open side faces up. 2. Locate the FB-DIMMs. 3. Holding the memory riser card by the two finger holes, pull it out of the memory cage and place the card DIMM-side-up on a soft, clean cloth. Mac Pro Memory (FB-DIMM)
  • Apple MB194G/A | Replacement Guide - Page 5
    4. Open the ejectors on the DIMM slot by pushing them out to the sides, and remove the FB-DIMM from the riser card. Warning: FB-DIMMs carry heatsinks on either side of the DIMM. Never attempt to remove the heatsinks from the DIMMs. Doing so could damage the DIMM. Mac Pro Memory (FB-DIMM) 
  • Apple MB194G/A | Replacement Guide - Page 6
    Installing the Replacement FB-DIMM 1. Align the DIMM in the slot on the memory riser card and push both ends of the DIMM down until the ejectors snap back up into place. 2. Insert the replacement riser card into position in the memory cage, pushing slightly until the card is seated in its logic
  • Apple MB194G/A | Replacement Guide - Page 7
    effort has been made to ensure that the information in this document is accurate. Apple is not responsible for printing or clerical errors. Apple 1 Infinite Loop Cupertino, CA 95014-2084 USA + 1 408 996 1010 http://www.apple.com Apple, the Apple logo, Mac, Macintosh, and Mac Pro are trademarks of
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
 Mac Pro
073-1062 Rev. A
Memory (FB-DIMM)
Replacement Instructions
Follow the instructions in this document carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Note:
The Mac Pro computer has two memory riser cards with a total of 8 memory slots. On each
card, the slots are arranged as two banks of two slots each. The computer comes with a minimum
of 1 GB of memory, installed as a pair of 512 MB fully buffered, dual inline memory modules (FB-
DIMMs) in two of the DIMM slots. Additional DIMMs can be installed in the open DIMM slots, as
illustrated below.
DIMMs must be installed in pairs of equal size from the same vendor. In the illustration below,
DIMMs in one colored pair do not need to match DIMMs in a different colored pair.