Adaptec AVA1515 Installation Guide
Adaptec AVA1515 - AVA 1515 Storage Controller Fast SCSI 10 MBps Manual
 |
View all Adaptec AVA1515 manuals
Add to My Manuals
Save this manual to your list of manuals |
Adaptec AVA1515 manual content summary:
- Adaptec AVA1515 | Installation Guide - Page 1
R AVA-1515 AT-to-SCSI Host Adapter Installation Guide vvvvvvvvvvvv - Adaptec AVA1515 | Installation Guide - Page 2
1 Getting Started This guide tells you how to install and configure the AVA™-1515 AT®-to-SCSI host adapter. Installation instructions are given in Sections 4 through 8. 2 Board Layout This figure identifies the major AVA-1515 components, and the table describes each component. AVA-1515 Host Adapter - Adaptec AVA1515 | Installation Guide - Page 3
to change options in the software (see Section 6, Software Installation). s If another Adaptec SCSI host adapter is already installed in your computer, you may need to change the interrupt channel and IRQ channel of the AVA-1515. Interrupt and IRQ setting must be the same number. If you change the - Adaptec AVA1515 | Installation Guide - Page 4
before you remove the chassis cover. See your computer's documentation for instructions on how to do this. 1 Remove the cover of your computer Connecting Peripherals Setting SCSI IDs You must assign a different SCSI ID to each device on the AVA-1515 SCSI bus. See your SCSI peripheral documentation - Adaptec AVA1515 | Installation Guide - Page 5
Caution: AVA-1515 host adapters support only single-ended SCSI devices. Differential SCSI devices may be damaged if connected to the host adapter. The peripheral documentation will tell you whether the device is single-ended or differential. 1 Lay - Adaptec AVA1515 | Installation Guide - Page 6
devices only (host adapter at end of bus) Internal and external devices (host adapter in the middle of the bus) AVA-1515 Terminators All three installed All three installed All three removed Terminating SCSI Peripherals 1 Check the manufacturer's documentation to determine how to enable or disable - Adaptec AVA1515 | Installation Guide - Page 7
AVA-1515 provides booting capability at AT port address 340h-35Fh. If you change this option, disable the BIOS, because the host adapter BIOS supports follow the instructions onscreen or in Troubleshooting Checklist If you have a problem during installation, check these items first: s Are all SCSI - Adaptec AVA1515 | Installation Guide - Page 8
see your dealer. 8 Jumper Block Settings The AVA-1515 jumper block settings are silkscreened on the board and 140h-15Fh 340h-35Fh* SCSI Parity Check I10 Interrupt 10 On Disabled option, disable the BIOS, because the host adapter BIOS supports booting only from the default port address range. 2 - Adaptec AVA1515 | Installation Guide - Page 9
bit, no parity. s For the latest online information about Adaptec products and services, call the Interactive Fax Service 23 hours a day at 408-957-7150. s For technical assistance, call Adaptec's Technical Support Hot Line at 800-959-SCSI (7274), or 408-945-2550. M-Th: 6:00a.m.-5:00p.m., F: 6:00a - Adaptec AVA1515 | Installation Guide - Page 10
used in accordance with the instructions, may cause harmful interference to user's authority to operate such equipment. Each AVA-1515 is equipped with an FCC compliance label Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are registered trademarks, and AVA is a trademark of Adaptec
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
R
▲▲▲▲▲▲▲▲▲▲▲▲
AVA-1515
AT-to-SCSI Host Adapter
Installation Guide