Adaptec 2126700 Installation Guide
Adaptec 2126700 - Ultra ATA Card 1233 Storage Controller Manual
 |
UPC - 760884145838
View all Adaptec 2126700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Adaptec 2126700 manual content summary:
- Adaptec 2126700 | Installation Guide - Page 1
Adaptec ASH-1233 ATA Adapter Installation Guide R - Adaptec 2126700 | Installation Guide - Page 2
1233 Adapter 15 This Installation Guide explains how to install the Adaptec ASH-1233 adapter, connect ATA hard disk drives to it, and install the device drivers for your operating system. For more detailed installation instructions, troubleshooting tips, and support and warranty information, refer - Adaptec 2126700 | Installation Guide - Page 3
System Requirements The minimum system requirements for the ASH-1233 adapter are: s Pentium II-266 MHz Processor or higher s Microsoft® Windows® 98SE, Windows Me, Windows 2000, or Windows XP s Available PCI slot with bus-mastering enabled Note: Refer to your system or motherboard documentation for - Adaptec 2126700 | Installation Guide - Page 4
IDE Connector Primary IDE Connector LED Connector PCI Connector Installation Checklist To successfully install your Adaptec ASH-1233 adapter and ATA disk drives, perform these tasks, in order: 1 Install drives and connect the cables. (See page 12.) 5 Install the device drivers. (See page 13.) 3 - Adaptec 2126700 | Installation Guide - Page 5
ASH-1233 Adapter You can install your Adaptec ASH-1233 adapter into a 32-bit or 64-bit PCI expansion slot. Note: If you are installing the adapter into the adapter. 2 Turn off power to the computer and disconnect the power cord. Open the computer cabinet, following the manufacturer's instructions. 4 - Adaptec 2126700 | Installation Guide - Page 6
3 Locate an unused expansion slot and remove the slot cover. Save the slot cover screw for use in Step 5. Slot cover screw Expansion slot cover 64-bit PCI expansion slots 32-bit PCI expansion slots 5 - Adaptec 2126700 | Installation Guide - Page 7
4 Insert the ASH-1233 adapter in the PCI expansion slot. Press down firmly until the adapter clicks into place. When installed properly, the adapter should appear level with the expansion slot. Note: Depending on the tightness of the PCI slot, gentle but firm force may be required to insert the - Adaptec 2126700 | Installation Guide - Page 8
or computer to computer, always refer to your ATA disk drive and computer documentation for specific instructions. Note: If you refer to the ATA drive's documentation for installation instructions, return to this document to continue with installation of the software included in your kit. Before - Adaptec 2126700 | Installation Guide - Page 9
: The Adaptec ASH-1233 adapter does not support Cable Select (CSEL) settings. You must change the jumper settings to set disk drives as master or slave. Connector (to Adapter) Connector (to Slave) Connector (to Master) To connect your ATA disk drives, follow the instructions - Adaptec 2126700 | Installation Guide - Page 10
Connecting One ATA Disk Drive on a Cable When you connect only one ATA disk drive to a cable, that disk drive must be set as a master drive. (See Setting Jumpers on ATA Disk Drives on page 7 for more information.) To connect one ATA drive to the ASH-1233 adapter: 1 Connect the IDE cable to an IDE - Adaptec 2126700 | Installation Guide - Page 11
2 Connect the other end of the IDE cable to a master drive, as shown below on the left. 3 Repeat Step 1 and 2 to connect a second ATA disk drive to the second IDE connector on the ASH-1233 adapter, as shown above on the right. Both disk drives must be set as master drives. Continue with Mounting ATA - Adaptec 2126700 | Installation Guide - Page 12
Connecting Two ATA Disk Drives to the Same Cable When you connect two ATA disk drives to a cable, one disk drive must be set as the master, the other must be set as the slave. (See Setting Jumpers on ATA Disk Drives on page 7 for more information.) To connect two disk drives to the same cable: 1 - Adaptec 2126700 | Installation Guide - Page 13
each ATA disk drive in an available drive bay inside your computer (as shown below). Refer to your computer and device documentation for instructions on installing devices inside your computer. 2 Connect a power cable from your computer's power supply to each ATA disk drive. 3 Close your computer - Adaptec 2126700 | Installation Guide - Page 14
see page 15. Note: For more detailed instructions and for instructions on verifying driver installation, refer to the User's Guide on the CD. To complete the installation Hardware Installation Wizard. To complete the device driver installation: 1 Insert the Adaptec ASH-1233 CD into your CD-ROM drive - Adaptec 2126700 | Installation Guide - Page 15
Windows 2000 When you power on your computer, Windows automatically detects the new adapter and opens the New Hardware Installation Wizard. To complete the device driver installation: 1 Insert the Adaptec ASH-1233 CD into your CD-ROM drive. 2 In the Wizard, click Next. 3 Select Search for a suitable - Adaptec 2126700 | Installation Guide - Page 16
installation. When you power on your computer, Windows automatically detects the new adapter and opens the New Hardware Installation Wizard. To complete the device driver installation: 1 Insert the Adaptec ASH-1233 CD into your CD-ROM drive. 2 In the Wizard, click Next. 3 Click Search for the best - Adaptec 2126700 | Installation Guide - Page 17
R Adaptec, Inc. 691 South Milpitas Boulevard Milpitas, CA 95035 USA ©2004 Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc. which may be registered in some jurisdictions. Part Number: 513908-06, Ver. AA LB 04/04
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
 |
 |
R
Adaptec ASH-1233
ATA Adapter
Installation Guide