Hunter 40135 Owner's Manual

Hunter 40135 Manual

Get Hunter 40135 PDF manuals and user guides View all Hunter 40135 manuals
Add to My Manuals
Save this manual to your list of manuals

Hunter 40135 manual content summary:

  • Hunter 40135 | Owner's Manual - Page 1
    Electronic/Mechanical Thermostat installation and operation manual Model 40135 1 44017-01 04-01-2008
  • Hunter 40135 | Owner's Manual - Page 2
    Our Technical Support Group is available from 8 am to 5 pm CST. They may be reached toll-free at 1-888-830-1326. 2
  • Hunter 40135 | Owner's Manual - Page 3
    Table of Contents Important Information 5 Tools 6 Uninstalling the Existing Unit 9 Installing the Thermostat 12 Installing the wall plate 14 connecting the wires 15 attaching the thermostat 17 Operation 20 Indicators & Adjustments 22 Troubleshooting 25 Wiring Diagrams 27 3
  • Hunter 40135 | Owner's Manual - Page 4
    Electronic/Mechanical Thermostat Model 40135 Congratulations! Thank you for choosing a Hunter thermostat. Your new Hunter thermostat will provide years of reliable service and year-round energy savings. Please read this manual before beginning installation and save this booklet for complete
  • Hunter 40135 | Owner's Manual - Page 5
    work on the following heating and cooling systems: Gas - Standing Pilot Gas - Electronic Ignition Gas - Fired Boilers Gas - Millivolt Systems Oil - Fired Boilers Oil - Fired Furnace Electric Air conditioner Electric Furnace This thermostat is not designed for heat pump systems or 110/220 V baseboard
  • Hunter 40135 | Owner's Manual - Page 6
    Tools This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your new thermostat, you will need the following supplies: Flat-head screwdriver Small Phillips-head screwdriver Hammer Electric drill and 3/16" bit Two fresh 1.5 Volt (AA) size alkaline
  • Hunter 40135 | Owner's Manual - Page 7
    NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ensure proper reconnection. 7
  • Hunter 40135 | Owner's Manual - Page 8
    RC Y G W RC Y G W 8
  • Hunter 40135 | Owner's Manual - Page 9
    to access the wires from the wall. (Some thermostats may have multiple covers, screws or other locking devices that must be removed or disengaged.) 3. Locate, but do not disconnect the wires. (If wires are not visible, they may be connected to the back of the wall plate. Some models may have doors
  • Hunter 40135 | Owner's Manual - Page 10
    If your existing thermostat is marked... RH / r / vr / 4 rc / vc y / c* / m w / h g / f label the wire with this sticker: G W Y RC RH 24 Volt RH 24 Volt Cool RC air conditioning compressor Y heating W fan G * See pg 27 for complete wiring diagram. 10
  • Hunter 40135 | Owner's Manual - Page 11
    and should not be used. If you have a wire marked C, do not connect it to any terminal. This wire is used only for non-battery powered thermostats. 5. Do not let the wires slip back into the wall during disconnection. You may want to secure the wires to the wall as you disconnect them. After all
  • Hunter 40135 | Owner's Manual - Page 12
    installing the thermostat INSTALLING THE THERMOSTAT 1. Remove the new thermostat from the back plate by pulling the two halves apart. Wall Plate Thermostat 12
  • Hunter 40135 | Owner's Manual - Page 13
    G 13 Y RC W
  • Hunter 40135 | Owner's Manual - Page 14
    installing the thermostat, cont. INSTALLING THE WALL PLATE 2. Position the new wall plate on the wall and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes, level the wall plate and mark the wall for
  • Hunter 40135 | Owner's Manual - Page 15
    Y G RC W RH 15
  • Hunter 40135 | Owner's Manual - Page 16
    installing the thermostat, cont. CONNECTING THE WIRES 1. Loosen, but do not remove, the terminal screws. Note: A jumper wire has been provided, connecting the RC and RH terminals for systems that do not provide both an RH and RC wire. If you have both an RH and RC wire, remove this jumper. If you do
  • Hunter 40135 | Owner's Manual - Page 17
    HE/HG Switch 17
  • Hunter 40135 | Owner's Manual - Page 18
    installing the thermostat, cont. ATTACHING THE THERMOSTAT 4. Locate the HE/HG switch on the back of the thermostat. Set the switch to HG mode.) 5. Insert two fresh AA alkaline batteries. 6. Align the thermostat with the the wall plate, and snap the two halves together. 7. Restore power at the
  • Hunter 40135 | Owner's Manual - Page 19
    19
  • Hunter 40135 | Owner's Manual - Page 20
    System Switch Thermometer Set Temperature Slider SY STEM 90 COOL OFF HEAT 90 30 80 80 70 70 20 60 60 AUTO 50 10 50 ON F F C Fan Switch Battery Indicator 20
  • Hunter 40135 | Owner's Manual - Page 21
    The System Switch determines the operating mode of the thermostat. Select Cool, Off, or Heat. 3. The Fan Switch should normally be located in the Auto position. To run the fan continuously, slide the Fan Switch to the On position. Note: In Auto , The fan will be turned on along with normal operation
  • Hunter 40135 | Owner's Manual - Page 22
    3. The second warning is the Shut-down Indicator, indicated by the Battery Indicator flashing approximately twice every second. When this warning appears, the thermostat is shut down and will turn your system OFF. Your system will remain shut-off until you install two fresh AA alkaline batteries. 22
  • Hunter 40135 | Owner's Manual - Page 23
    Span Adjust SPAN 23
  • Hunter 40135 | Owner's Manual - Page 24
    run LONGER, turn the Span Adjust clockwise. 3. To make your system run SHORTER, turn the Span Adjust counter clockwise. 4. Reattach the top cover to the thermostat. Note: The Span range is 0.6oF - 3oF. The Span setting remains the same in both the Heat and Cool modes and can be changed regardless
  • Hunter 40135 | Owner's Manual - Page 25
    AA alkaline batteries. 1 e. If applicable, make sure the furnace blower door is closed properly. 1 f. If your system has 4 wires, ensure the jumper wire is installed between the RC and RH terminals. 2. My system continues to operate when the thermostat is in the off position. 2 a. Replace unit. 25
  • Hunter 40135 | Owner's Manual - Page 26
    troubleshooting Is there help on the web? Yes. Visit http://www.hunterfan.com for more information. Can't I just call someone? Sure. Our Technical Support Group is available from 8 am to 5 pm CST. They may be reached toll-free at1-888-8301326. 26
  • Hunter 40135 | Owner's Manual - Page 27
    4-w ire Heat/CoolSystem G Rh Y W Fan Relay Heat/Cool Cool HeatRelay 24V Supply Contactor orValve 5-wireeaHt/oCol Ssytem G Rc Rh Y W Fan Cool Heat Cool Heat Reyla Relay 24V Supply 24V SupplyContacotr or aVlve 27
  • Hunter 40135 | Owner's Manual - Page 28
    wiring diagrams 2-w ire HeatOnlySystem Rh W Heat24V or HeatRelay M illivoltSupply orValve 3-w ire HeatOnlySystem G Rh W Fan Relay Heat24V Supply HeatRelay orValve 28
  • Hunter 40135 | Owner's Manual - Page 29
    wiring diagrams, cont. 3-w ire CoolOnlySystem G Rc Fan Relay Cool24V Supply Y Cool Contacter 29
  • Hunter 40135 | Owner's Manual - Page 30
    30 © 2007 Hunter Fan Company
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
1
Electronic/Mechanical
Thermostat
Model 40135
installation and
operation manual
44017-01
04-01-2008